Revision Number: Issue date: 12/27/ PRODUCT AND COMPANY IDENTIFICATION. IDH number: HAZARDS IDENTIFICATION

Transcription

1 Safety Data Sheet Revision Number: Issue date: 12/27/ PRODUCT AND COMPANY IDENTIFICATION Product name: LOCTITE EA 9309NA AERO PART A QT known as EA 9309 NA PART A QUART Product type: Adhesive for the Aerospace Industry Item number: AA Restriction of Use: identified Region: United States Company address: Henkel Corporation One Henkel Way Rocky Hill, Connecticut Contact information: Telephone: (860) MEDICAL EMERGENCY Phone: Poison Control Center (toll free) or TRANSPORT EMERGENCY Phone: CHEMTREC (toll free) or Internet: 2. HAZARDS IDENTIFICATION WARNING: EMERGENCY OVERVIEW CAUSES SKIN IRRITATION. MAY CAUSE AN ALLERGIC SKIN REACTION. CAUSES SERIOUS EYE IRRITATION. HAZARD CLASS HAZARD CATEGORY SKIN IRRITATION 2 EYE IRRITATION 2A SKIN SENSITIZATION 1 PICTOGRAM(S) Precautionary Statements Prevention: Response: Storage: Disposal: Avoid breathing vapors, mist, or spray. Wash affected area thoroughly after handling. Contaminated work clothing should not be allowed out of the workplace. Wear protective gloves, eye protection, and face protection. IF ON SKIN: Wash with plenty of water. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If skin irritation or rash occurs: Get medical attention. If eye irritation persists: Get medical attention. Take off contaminated clothing. Not prescribed Dispose of contents and/or container according to Federal, State/Provincial and local governmental regulations. Classification complies with OSHA Hazard Communication Standard (29 CFR ) and is consistent with the provisions of the United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS). See Section 11 for additional toxicological information. 3. COMPOSITION / INFORMATION ON INGREDIENTS Page 1 of 6

2 Hazardous Component(s) CAS Number Percentage* Bisphenol A - Epichlorohydrin Polymer Treated fumed silica Glass, oxide, chemicals * Exact percentages may vary or are trade secret. Concentration range is provided to assist users in providing appropriate protections. 4. FIRST AID MEASURES Inhalation: Skin contact: If inhaled, immediately remove the affected person to fresh air. If symptoms develop and persist, get medical attention. If breathing is difficult, give oxygen. If not breathing, give artificial respiration. Remove contaminated clothing and footwear. Immediately wash skin thoroughly with soap and water. If symptoms develop and persist, get medical attention. Eye contact: In case of contact with the eyes, rinse immediately with plenty of water for 15 minutes, and seek immediate medical attention. Ingestion: Get immediate medical attention. If symptoms develop and persist, get medical attention. Symptoms: See Section 11. Notes to physician: Treat symptomatically and supportively. 5. FIRE FIGHTING MEASURES Extinguishing media: Special firefighting procedures: Unusual fire or explosion hazards: Hazardous combustion products: Water spray (fog), foam, dry chemical or carbon dioxide. Wear self-contained breathing apparatus and full protective clothing, such as turn-out gear. Cartridge respirators do not provide adequate protection for fire fighters or exotherm mitigation. May liberate large quantities of dense, foul-smelling smoke which may contain unidentified toxic gasses. Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. Oxides of nitrogen. 6. ACCIDENTAL RELEASE MEASURES Use personal protection recommended in Section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel. Environmental precautions: Clean-up methods: Prevent further leakage or spillage if safe to do so. Wear appropriate protective equipment and clothing during clean-up. Do not allow product to enter sewer or waterways. Scrape up spilled material and place in a closed container for disposal. Dispose of according to Federal, State and local governmental regulations. Page 2 of 6

3 7. HANDLING AND STORAGE Handling: Storage: Prevent contact with eyes, skin and clothing. Do not breathe vapor and mist. Wash thoroughly after handling. Use only with adequate ventilation. Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. For information on product shelf life, please review labels on container or check the Technical Data Sheet. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Employers should complete an assessment of all workplaces to determine the need for, and selection of, proper exposure controls and protective equipment for each task performed. Hazardous Component(s) ACGIH TLV OSHA PEL AIHA WEEL OTHER Bisphenol A - Epichlorohydrin Polymer 10 mg/m3 TWA 15 mg/m3 TWA Total Inhalable dust. dust. Treated fumed silica 3 mg/m3 TWA 5 mg/m3 TWA Respirable fraction. Respirable fraction. Glass, oxide, chemicals 10 mg/m3 TWA Inhalable dust. 3 mg/m3 TWA Respirable fraction. 15 mg/m3 TWA Total dust. 5 mg/m3 TWA Respirable fraction. Engineering controls: Respiratory protection: Eye/face protection: Skin protection: Provide local and general exhaust ventilation to effectively remove and prevent buildup of any vapors or mists generated from the handling of this product. If ventilation is not sufficient to effectively prevent buildup of aerosols, mists or vapors, appropriate NIOSH/MSHA respiratory protection must be provided. Safety goggles or safety glasses with side shields. Wear impervious gloves for prolonged contact. Use of impervious apron and boots are recommended. 9. PHYSICAL AND CHEMICAL PROPERTIES Physical state: Liquid, paste Color: Beige Odor: Slight Odor threshold: ph: Neutral Vapor pressure: Not applicable Boiling point/range: Melting point/ range: Specific gravity: Vapor density: > 1 Flash point: > 140 C (> 284 F) Flammable/Explosive limits - lower: Flammable/Explosive limits - upper: Autoignition temperature: Not applicable Flammability: Not applicable Evaporation rate: Solubility in water: Not miscible or difficult to mix Partition coefficient (n-octanol/water): VOC content: < 10 g/l per SCAQMD Rule 1124 [EPA Test Method 24/304-91] (estimated) Viscosity: Decomposition temperature: Page 3 of 6

4 10. STABILITY AND REACTIVITY Stability: Hazardous reactions: Hazardous decomposition products: Incompatible materials: Reactivity: Conditions to avoid: Stable at normal conditions. May occur. Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. Oxides of nitrogen. Keep away from strong oxidizing agents, strong Lewis or mineral acids. Avoid mixing resin (Part A) and curing agent (Part B) unless you plan to use immediately. Do not heat mixed adhesive unless curing surfaces to be bonded. Failure to observe these precautions may result in excessive heat build-up causing an exotherm. 11. TOXICOLOGICAL INFORMATION Relevant routes of exposure: Skin, Inhalation, Eyes, Ingestion Potential Health Effects/Symptoms Inhalation: Skin contact: Eye contact: Ingestion: May cause respiratory tract irritation. May cause allergic respiratory reaction. This product may cause irritation to the skin. This product may cause an allergic skin reaction. This product may cause irritation to the eyes. Ingestion may cause gastrointestinal irritation, nausea, vomiting and diarrhea. May be harmful if swallowed. Hazardous Component(s) LD50s and LC50s Immediate and Delayed Health Effects Allergen, Irritant Bisphenol A - Epichlorohydrin Polymer Allergen, Irritant Treated fumed silica Irritant Glass, oxide, chemicals Allergen, Respiratory Hazardous Component(s) NTP Carcinogen IARC Carcinogen OSHA Carcinogen (Specifically Regulated) No No No Bisphenol A - Epichlorohydrin Polymer No No No Treated fumed silica No No No Glass, oxide, chemicals No No No 12. ECOLOGICAL INFORMATION Ecological information: Toxic to aquatic organisms Page 4 of 6

5 13. DISPOSAL CONSIDERATIONS Information provided is for unused product only. Recommended method of disposal: Hazardous waste number: Dispose of according to Federal, State and local governmental regulations. Material, if discarded, is not expected to be a characteristic hazardous waste under RCRA. Wastes must be tested using methods described in 40 CFR Part 261 to determine if it meets applicable definitions of hazardous wastes. 14. TRANSPORT INFORMATION The transport information provided in this section only applies to the material/formulation itself, and is not specific to any package/configuration. U.S. Department of Transportation Ground (49 CFR) Proper shipping name: Not regulated Hazard class or division: Identification number: Packing group: International Air Transportation (ICAO/IATA) Proper shipping name: Environmentally hazardous substance, liquid, n.o.s. (Bisphenol-A Epichlorhydrin resin, Bisphenol A diglycidyl ether) Hazard class or division: 9 Identification number: UN 3082 Packing group: III Water Transportation (IMO/IMDG) Proper shipping name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (Bisphenol-A Epichlorhydrin resin, Bisphenol A diglycidyl ether) Hazard class or division: 9 Identification number: UN 3082 Packing group: III Marine pollutant: Bisphenol-A Epichlorhydrin resin, Bisphenol A diglycidyl ether United States Regulatory Information 15. REGULATORY INFORMATION TSCA 8 (b) Inventory Status: TSCA 12 (b) Export Notification: CERCLA/SARA Section 302 EHS: CERCLA/SARA Section 311/312: CERCLA/SARA Section 313: California Proposition 65: All components are listed or are exempt from listing on the Toxic Substances Control Act inventory. above reporting de minimis above reporting de minimis. Immediate Health, Delayed Health above reporting de minimis. This product contains a chemical known in the State of California to cause cancer. This product contains a chemical known to the State of California to cause birth defects or other reproductive harm. Canada Regulatory Information CEPA DSL/NDSL Status: One or more components are not listed on, and are not exempt from listing on either the Domestic Substances List or the Non-Domestic Substances List. 16. OTHER INFORMATION This safety data sheet contains changes from the previous version in sections: New information added in Section(s): 1,12 Page 5 of 6

6 Prepared by: Mark Mau, Regulatory Affairs Specialist Issue date: 12/27/2016 DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. However, Henkel Corporation and its affiliates ( Henkel ) does not assume responsibility for any results obtained by persons over whose methods Henkel has no control. It is the user s responsibility to determine the suitability of Henkel s products or any production methods mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property and persons against any hazards that may be involved in the handling and use of any Henkel s products. In light of the foregoing, Henkel specifically disclaims all warranties, express or implied, including warranties of merchantability and fitness for a particular purpose, arising from sale or use of Henkel s products. Henkel further disclaims any liability for consequential or incidental damages of any kind, including lost profits. Page 6 of 6