Instructions. Fibrlok Optical Fiber Splicing System. Issue 6, August 1991

Size: px
Start display at page:

Download "Instructions. Fibrlok Optical Fiber Splicing System. Issue 6, August 1991"

Transcription

1 Instructions TM Fibrlok Optical Fiber Splicing System Issue 6, August 1991

2 1.0 General The 3M brand Fibrlok TM Optical Fiber Splicing System provides permanent mechanical splices for single or multi mode fiber having 125 µm diameter cladding. Three color coded versions of the Fibrlok Splice are available for splicing 250 µm and 900 µm diameter plastic coated fiber. The Fibrlok 2525 Splice is for splicing 250 µm fiber to 250 µm fiber: The Fibrlok 2590 Splice is for splicing 250 µm fiber to 900 µm fiber: The Fibrlok 2599 Splice is for splicing 900 µm fiber to 900 µm fiber: 1.01 Fibrlok Optical Fiber Splice Cap Fiber Size Designation Circles (1/4 circle for 250 µm coating, full circle for 900 µm coated fiber) End Plug (each end) Fiber Entry Port (each end) Jacket

3 1.02 Fibrlok 2501 Assembly Tool Fiber Retention Pad Fiber Alignment Guides (2) Splice Holding Cradle Pivoted Handle (shown open) Fiber Retention Pad Toggle Arm Toggle Arm Mounting Holes (4) Instruction Label (2) Finger Cutout Base Fiber Cleave Length Gauge (both ends of tool) 1.03 Tools and Materials Required Fibrlok TM 2500 or 2501 Assembly Tool Plastic Coating (Buffer) Stripper Reagent Grade Isopropyl Alcohol Lint Free Wipes Cleaver Fibrlok 2505 Assembly Tool Mounting Adaptor (optional) Fibrlok Video Instruction Tape (optional) Tool Kit (optional) 1.04 Compatible Organizers 3M 2118, 3M 2524 AT&T UC-SS/M1 GTE Part , Siecor M Others compatible with minor modifications: DiTel UST 3000, UST 3010, UST 3500 AT&T , , , Raychem FOSC 100/TK

4 2.0 Splicing Set-Up 2.01 The splicing area should be clean, dry and well-lighted. A clean, well organized splicing area will improve splicing efficiency and minimize the risk of contamination of fibers or splices Open the buffer tubes, expose and clean the fibers per company practice. Storage, use and disposal of isopropyl alcohol should be per company health and safety instructions. Refer to solvent label or Material Safety Data Sheet See Section 5.0 for recommended procedures for fiber organization and splice storage Remove Fibrlok splice from protective package. Load the splice into the assembly tool by pressing firmly at the ends of the splice. Carefully follow health and safety information on Fibrlok Splice label or Material Safety Data Sheet If using the Fibrlok 2501 Assembly Tool, rotate the toggle arms for the appropriate fiber size. Inward µm Outward µm

5 3.0 Fiber Preparation 1" to 2" (depending on cleaver) 3.01 Remove the minimum length of fiber required to prepare and splice the fibers Strip approximately 1 to 2 inches (2.5 to 5 cm) of plastic coating from the fiber using a mechanical stripper. The stripper used should be in good operating condition to prevent scratches or other damage to the glass cladding Clean the bare glass by pulling the fiber through an alchohol soaked lint-free wipe. This will remove any fragments or dirt remaining on the fiber. Do not wipe the fibers more than two times, and limit the time that the bare fiber is exposed to the atmosphere Cleave fiber to the length indicated on the chart. Fibrlok Splice Designation 3M Fibrlok 2525 (250 µm x 250 µm) 3M Fibrlok 2590 (250 µm x 900 µm) 3M Fibrlok 2599 (900 µm x 900 µm) Cleave Length for End of Splice with Black Plug & Symbol 12.5 mm ± 0.5 mm (.492 in. ±.020 in.) 12.5 mm ± 0.5 mm (.492 in. ±.020 in.) Cleave Length for End of Splice with White Plug & Symbol 14.0 mm ± 0.5 mm (.551 in. ±.020 in.) 14.0 mm ± 0.5 mm (.551 in ±.020 in.) The cleaver should be in good operating condition and used in accordance with the manufacturer s instructions. A cleaver that produces cleaved ends within 2 of perpendicular and free of major defects is recommended. Dispose of cleaved fiber ends per company practice. 12.5mm 3.05 Check the cleave length using the cleave length gauge on the Fibrlok Assembly Tool. Adjust the cleaver to provide the prescribed cleave lengths. Check cleave lengths periodically during subsequent splicing operations. Do not allow cleaved end to contact tool. 14.0mm

6 4.0 Splice Assembly 4.01 Push the fiber down into the fiber retention pad on the proper side of the splice. Hold the coated portion of the fiber ONLY. Do not allow the cleaved end to contact any surface before insertion into the splice Grasp the coated fiber about.25 inches (6 mm) from the bare glass and move the fiber end onto the fiber alignment guide on the Assembly Tool such that the end is resting on the alignment guide outside of the splice. Fiber should be inserted into the splice immediately following cleaning and placing in retention pad to minimize exposure to the atmosphere and reduce the risk of contamination. Push fiber straight into fiber alignment guide... Not at an angle Gently continue pushing the fiber into the splice until resistance is felt. When fully inserted, the first fiber should be straight or have a slight bow - up to.1 inch (3 mm). If properly inserted, bare glass should not be visible outside of splice. If bare glass is visible, pull back slightly on fiber and continue insertion until resistance is met. Never fully remove fibers from splice after initial insertion. Do not pull on fiber after it has been properly inserted.

7 4.04 Prepare second fiber (strip, clean and cleave) as described in Section Lay fiber into foam retention pad and begin to insert the fiber end into the splice, as in 4.01 and Gently push the second fiber in small increments straight through the alignment guide into the fiber entry port. As the coating of the second fiber enters the fiber entry port, watch for the bow in the first fiber to increase. This occurs when the end face of the second fiber contacts the first fiber and pushes the first fiber slightly back out of the splice. Continue gently pushing the second fiber until it meets resistance. Following proper insertion, the second fiber will be approximately straight but may have up to a.1 inch (3 mm) maximum bow. At this point, the first fiber will have a larger bow than the second fiber and larger than it had initially Push the first fiber back against the second fiber until there are equal bows in both fibers. Do not pull on either of the fibers following establishment of the bows in the first and second fibers. The fiber ends must be held together by the compressive forces induced by the bows to produce a low loss splice Pivot the handle of the Fibrlok Assembly Tool down until it contacts the cap of the Fibrlok Splice. Squeeze the handle of the assembly tool as shown in order to close cap and actuate the splice. When possible, secure the tool to a work surface for added support. A snap sound will be heard when the splice is actuated.

8 4.09 Remove the Fibrlok Splice from the Assembly Tool by first removing the fibers from the foam retention pads and then lifting the splice from the splice holding cradle. Do not attempt to tune or optimize the splice as this may result in higher splice loss. Fibrlok splices optimize fiber alignment within the metal element inside the splice when properly installed per the previous instructions. If fiber bows are NOT observed as described, repeat steps of Splice Assembly but DO NOT fully remove fibers from splice. If bows are still not observed, remove fibers, strip, and recleave checking for proper cleave length. Resplice per splicing procedure using_a_new splice. In the event a splice must be refabricated, simply cut the fibers at each end of the splice (this will remove 1 1/2" of fiber from the loop) and resplice per instructions. Splice refabrication will require a length of 2 inches on each fiber. DO NOT REUSE FIBRLOK SPLICES. 5.0 Fiber Organization and Splice Storage When storing fiber slack in a splice tray, the spliced fiber ends will twist one full turn for each full loop of fiber being stored. This rotation places stress on the fibers. This rotational stress makes fiber organization more difficult and may affect fiber/splice performance, particularly in 900 µm coated fibers. The stiffness of the 900 µm fiber does not distribute this stress in the same manner as 250 µm coated fiber. The following procedure is strongly recommended when splicing 900 µm coated fibers and will improve fiber organization when splicing all fiber types Secure the buffer tubes of the fibers to be spliced to the tray so that the fibers are free to rotate through the point of attachment Select the first two fibers to be spliced and lay them into the tray. Trim the fibers so they are the right length for splicing plus approximately 1 to 2 inches (2.5 to 5 cm) for fiber end preparation.

9 5.03 Place the splice assembly tool close to or on top of the splice tray. Match the orientation of the tool to that of the splice holder or tray whenever possible Remove the minimum amount of fiber required for fiber preparation and splicing. Remove less than one loop if possible Prepare fibers and complete splice as desribed in Section 3 and Carefully lay the splice on top of the holder without securing the splice into the holder.

10 5.07 Storing 250 µm to 250 µm and 900 µm to 900 µm splices: 1. Store the shorter of the two fibers in the tray. 2. Observe how the splice lays in its relaxed state. Rotate the splice through the smallest possible angle to install it in the tray. 3. Store the second fiber. Storing 250 µm to 900 µm splices: 1. Store the 900 µm fiber first. 2. Grasping the splice by the 900 µm fiber, observe how the splice lays in its relaxed state. Rotate the splice through the smallest possible angle to install it into the tray. 3. Store the 250 µm fiber. 6.0 Splicing Accessories 6.01 The 3M Fibrlok TM 2524 Splice Organizer Tray holds up to 24 Fibrlok Splices and provides superior fiber and splice organization. Easily installed, the tray will accommodate up to eight buffer tubes holding up to 48 fibers (250 µm or 900 µm coated fibers) and can be adapted for fusion splice storage. The 2524 Splice Tray fits and mounts into the 3M 2177 Fiber Optic Splice Closure, the 3M 2178 Fiber Optic Splice Case and the 3M 2190 PST Fiber Optic Splice Closure. It is also compatible with a variety of non-3m closures The 3M Fibrlok TM 2505 Assembly Tool Mounting Adapter permits mounting of the Fibrlok Assembly Tool on standard 3M MS 2TM Splicing Rigs, conventional camera-type tripods, and other standard telco splicing rig components. The 2505 Mounting Adapter provides the ability to mount the Fibrlok Assembly Tool on a variety of surfaces, and in any orientation, for splicing in difficult locations such as manholes, aerial splice points, pedestals and distribution frames.

11 6.03 3M Fiber Preparation Kits provide all the tools necessary for the assembly of the Fibrlok Splice. Fiber Splice Preparation Kits are available in a variety of combinations with or without the Fibrlok Assembly Tool and/or the cleaving tool, for those who may already own these splicing tools: Fiber Splice Preperation Kits: #2530 Kit with all components listed below and Thomas & Betts Cleave Tool #2531 Kit with all components listed below #2533 Kit with all components listed below excluding Fibrlok Assembly 3M Stock Number Splice Kits Components Listing (available seperately) Fibrlok Assembly Tool Cable Strippers Cleaning Alcohol Bottle Scissors No-Nik Stripper (.008) Micro-Stripper (.006) Lint Free Cloth (100/pkg.) Magnifier, Cleaved Fiber Inspection Coaxial Cable Stripper Instruction Manual

12 Important Notice All statements, technical information and recommendations related to the Seller's products are based on information believed to be reliable, but the accuracy or completeness thereof is not guaranteed. Before utilizing the product, the user should determine the suitability of the product for its intended use. The user assumes all risks and liability whatsoever in connection with such use. Any statements or recommendations of the Seller which are not contained in the Seller's current publications shall have no force or effect unless contained in an agreement signed by an authorized officer of the Seller. The statements contained herein are made in lieu of all warranties, express or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose which warranties are hereby expressly disclaimed. SELLER SHALL NOT BE LIABLE TO THE USER OR ANY OTHER PERSON UNDER ANY LEGAL THEORY, INCLUDING BUT NOT LIMITED TO NEGLIGENCE OR STRICT LIABILITY, FOR ANY INJURY OR FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES SUSTAINED OR INCURRED BY REASON OF THE USE OF ANY OF THE SELLER'S PRODUCTS THAT WERE DEFECTIVE M TelComm Products Division 6801 River Place Blvd. Austin, TX M Litho in U.S.A.

Instructions. Fibrlok II Optical Fiber Splicing System. Issue 1, June 1992

Instructions. Fibrlok II Optical Fiber Splicing System. Issue 1, June 1992 Instructions TM Fibrlok II Optical Fiber Splicing System Issue 1, June 1992 Contents: 1.0 General... 1 2.0 Splicing Set-up... 3 3.0 Fiber Preparation... 4 4.0 Splice Assembly... 4 5.0 Fiber Repositioning...

More information

Fibrlok II 2529 Universal Optical Fiber Splice

Fibrlok II 2529 Universal Optical Fiber Splice Fibrlok II 2529 Universal Optical Fiber Splice Instructions October 2002 34-7035-4458-4-D Contents: 1.0 General...3 2.0 Splicing Set-up...4 3.0 Fiber Preparation...5 4.0 Splice Assembly...6 5.0 Fiber Repositioning...8

More information

Fibrlok II 2529 Universal Optical Fiber Splice

Fibrlok II 2529 Universal Optical Fiber Splice Fibrlok II 2529 Universal Optical Fiber Splice Instructions January 2007 78-8128-0163-3-E Contents: 1.0 General... 3 2.0 Splicing Set-up... 4 3.0 Fiber Preparation... 5 4.0 Splice Assembly... 6 5.0 For

More information

Mass Fusion Splicing of Optical Fiber Ribbon Cables

Mass Fusion Splicing of Optical Fiber Ribbon Cables Application Notes Mass Fusion Splicing of Optical Fiber Ribbon Cables Author Prasanna Pardeshi and Sudipta Bhaumik Issued January 2014 Abstract To build a fiber optic network, one may eventually join two

More information

OPTICAL FIBER SPLICING. Courtesy from Significant Technologies Sdn Bhd

OPTICAL FIBER SPLICING. Courtesy from Significant Technologies Sdn Bhd OPTICAL FIBER SPLICING Introduction Reason for jointing: - Increase fiber span (long cable runs) Connecting devices such as amplifiers, pigtails, etc. to fibers TYPES OF SPLICING Two types of splicing

More information

Assembly Instruction for Fiber Optic Series FOH Fischer Connectors

Assembly Instruction for Fiber Optic Series FOH Fischer Connectors Assembly Instruction for Fiber Optic Series FOH Fischer Connectors Table des matières 1 Introduction... 3 2 Document history... 3 3 Definitions and Acronyms... 3 4 FOH Plugs & Receptacles with Potting

More information

C200 bands are available in a variety of colors. Visit us at LifeTrakUSA.com

C200 bands are available in a variety of colors. Visit us at LifeTrakUSA.com Information Guide HOW TO CHANGE YOUR BANDS The bands of your C200 are reversible and replaceable: 1. Carefully slide the bands off the Core. The bands can slide in either direction. 1 C200 bands are available

More information

Single Use Curlew TM Multiple Biopsy Forceps

Single Use Curlew TM Multiple Biopsy Forceps Single Use Curlew TM Multiple Biopsy Forceps 13 SPECIMEN WITH METAL STORAGE CYLINDER With In Situ Fixation, Batch or Single Specimen Collection US Patents 5,782,747; 5,980,468; 6,071,248; foreign patents

More information

USER MANUAL Rev. 1.15

USER MANUAL Rev. 1.15 QUANTUM QSP 7 TM BEACH CHAIR SHOULDER POSITIONER (BCP) USER MANUAL Rev. 1.15 Please read all the following instructions carefully to ensure proper functionality and to avoid injury or damage to your device.

More information

Product Specifications and Usage Information P4405, P4410, & P4420 Genesys 30 Dosimeter Holder System

Product Specifications and Usage Information P4405, P4410, & P4420 Genesys 30 Dosimeter Holder System DESCRIPTION The Thermo Genesys 30 Spectrophotometer (G30) is supplied with specially designed dosimeter holders to fit a variety of dosimeters, including the B3 DoseStix and B3 WINdose dosimeters. The

More information

How To Get The Most Out of Your StarSet Headset

How To Get The Most Out of Your StarSet Headset How To Get The Most Out of Your StarSet Headset Behind The Ear StarSet 1 1. StarSet capsule 5. Cord 9. Instruction pamphlet 2. Acoustic tube 3. Earpiece termination 6. Adjustable clothing clip 7. Plug

More information

Instructions for Use Reprocessed ENDOPATH XCEL Bladeless Endoscopic Trocars and Cannulas. Reprocessed Device for Single Use.

Instructions for Use Reprocessed ENDOPATH XCEL Bladeless Endoscopic Trocars and Cannulas. Reprocessed Device for Single Use. Reprocessed by Instructions for Use Reprocessed ENDOPATH XCEL Bladeless Endoscopic Trocars and Cannulas Reprocessed Device for Single Use Caution: Federal (U.S.A.) law restricts this device to sale by

More information

PCR Starter Kit. For 96-well blocks, 0.2 ml USER GUIDE USER GUIDE. Part. No. A24829 Revison B

PCR Starter Kit. For 96-well blocks, 0.2 ml USER GUIDE USER GUIDE. Part. No. A24829 Revison B USER GUIDE USER GUIDE PCR Starter Kit For 96-well blocks, 0. ml Part. No. A489 Revison B For Research Use Only. Not for use in diagnostic procedures. Manufacturer's address: Life Technologies Holdings

More information

Blood Glucose Monitoring System. User Guide

Blood Glucose Monitoring System. User Guide Blood Glucose Monitoring System User Guide Table of Contents Introduction...2 Important Safety Instructions...2 About ipet PRO Blood Glucose Monitoring System...3 About ipet PRO Meter...4 About the ipet

More information

LET OUR IMAGE ENHANCE YOUR IMAGE. Operating Instructions MedRx Video Portable OtoScope System

LET OUR IMAGE ENHANCE YOUR IMAGE. Operating Instructions MedRx Video Portable OtoScope System LET OUR IMAGE ENHANCE YOUR IMAGE Operating Instructions MedRx Video Portable OtoScope System RD2 Portable Video Otoscope Manual Rev 1 Effective September 2004 Table of Contents Introduction to the MedRx

More information

MARCY DIAMOND ELITE UTILITY BENCH MD-440. Model MD-440. Retain This Manual for Reference OWNER'S MANUAL

MARCY DIAMOND ELITE UTILITY BENCH MD-440. Model MD-440. Retain This Manual for Reference OWNER'S MANUAL NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier MARCY DIAMOND ELITE UTILITY BENCH MD-440 Assembly Instruction Parts List Warranty

More information

Quick Start Guide. Venipuncture and Intramuscular Injection Training Arm

Quick Start Guide. Venipuncture and Intramuscular Injection Training Arm Venipuncture and Intramuscular Injection Training Arm Quick Start Guide Realistic training arm for demonstrating and practicing proper venipuncture procedure and deltoid intramuscular injections. The venous

More information

Ribbon Splitting Tool (RST-000)

Ribbon Splitting Tool (RST-000) Ribbon Splitting Tool (RST-000) P/N 004-098 Issue 12 related literature Search www.corning.com/opcomm. Click on Resources. Slider button Latch 1. General Figure 1 1.1 This procedure describes how to divide

More information

FOSC. Fiber Optic Splice Closures. FOSC Splicing Trays and Storage Baskets

FOSC. Fiber Optic Splice Closures. FOSC Splicing Trays and Storage Baskets FOSC Ordering Guide FOSC Fiber Optic Splice Closures FOSC Splicing Trays and Storage Baskets This document provides assistance with the selection of FOSC trays and storage baskets for use in FOSC closures.

More information

How to Use ENBREL : Vial Adapter Method

How to Use ENBREL : Vial Adapter Method How to Use ENBREL : Vial Adapter Method SETTING UP FOR AN INJECTION Select a clean, well-lit, flat working surface, such as a table. Take the ENBREL dose tray out of the refrigerator and place it on your

More information

TABLE OF CONTENTS 1.1. WARRANTY DAMAGED SHIPMENTS SERVICE INTRODUCTION UNPACKING AND INSTALLATION

TABLE OF CONTENTS 1.1. WARRANTY DAMAGED SHIPMENTS SERVICE INTRODUCTION UNPACKING AND INSTALLATION TABLE OF CONTENTS EDITION 5 Section 1 - WARRANTY & SERVICE 1.1. WARRANTY 2 1.2. DAMAGED SHIPMENTS 2 1.3. SERVICE 2 Section 2 - INTRODUCTION 2.1. INTRODUCTION 3 Section 3 - GENERAL 3.1. UNPACKING AND INSTALLATION

More information

SDS 4.0 Tips and Tricks

SDS 4.0 Tips and Tricks SDS 4.0 Tips and Tricks Content Important information 3 SDS 4.0 Fit and Go Box overview 4 Selecting the receiver length 5 Choosing the correct earpiece for the receiver 6 Attaching / removing the retention

More information

`bob`=å~ãéê~=ó=å~êéi=åäé~åáåöi= ÇáëáåÑÉÅíáçå=~åÇ=ëíÉêáäáò~íáçå

`bob`=å~ãéê~=ó=å~êéi=åäé~åáåöi= ÇáëáåÑÉÅíáçå=~åÇ=ëíÉêáäáò~íáçå kéï=~ë=çñw MUKOMNT `bob`=å~ãéê~=ó=å~êéi=åäé~åáåöi= ÇáëáåÑÉÅíáçå=~åÇ=ëíÉêáäáò~íáçå fåëíêìåíáçåë=ñçê=`bob`=lãåáå~ã=~åç=`bob`=_äìéå~ã Eî~äáÇ=Ñçê=rp^F båöäáëü=erpf CEREC camera care, cleaning, disinfection

More information

VISTA400 REMOVABLE FOOT PLATE. Instructions For Use. Step on yellow pedals to close and open legs to go around chairs & ambulate.

VISTA400 REMOVABLE FOOT PLATE. Instructions For Use. Step on yellow pedals to close and open legs to go around chairs & ambulate. VISTA400 Instructions For Use Squeeze the yellow bar & push down/pull up to activate pneumatic stand assist. Step on yellow pedals to close and open legs to go around chairs & ambulate. Pull yellow levers

More information

PCR Starter Kit. For 3 32-well blocks, 0.2 ml USER GUIDE USER GUIDE. Part. No Revison B

PCR Starter Kit. For 3 32-well blocks, 0.2 ml USER GUIDE USER GUIDE. Part. No Revison B USER GUIDE USER GUIDE PCR Starter Kit For 3 3-well blocks, 0. ml Part. No. 4485765 Revison B For Research Use Only. Not for use in diagnostic procedures. Manufacturer's address: Life Technologies Holdings

More information

COR. Precision Targeting Cartilage Repair System. Arthroscopic Technique for Repair of Osteochondral Defects

COR. Precision Targeting Cartilage Repair System. Arthroscopic Technique for Repair of Osteochondral Defects COR Precision Targeting Cartilage Repair System Arthroscopic Technique for Repair of Osteochondral Defects Planning the Procedure An 18-gauge spinal needle is initially used to plan a perpendicular approach

More information

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following. Read all instructions before using this appliance. DANGER - To reduce

More information

INSTRUCTIONS FOR PREPARING AND GIVING AN INJECTION OF ENBREL POWDER

INSTRUCTIONS FOR PREPARING AND GIVING AN INJECTION OF ENBREL POWDER INSTRUCTIONS FOR PREPARING AND GIVING AN INJECTION OF ENBREL POWDER Introduction The following instructions explain how to prepare and inject Enbrel powder for injection. Please read the instructions carefully

More information

Tips for Training New Customers

Tips for Training New Customers Tips for Training New Customers Good Habits: Test Strips Recap vial immediately and tightly after removing a single test strip. Never remove the desiccant from the vial. Do not lay test strips out ahead

More information

weight.detach/bench ITEM NO: 76310

weight.detach/bench ITEM NO: 76310 weight.detach/bench ITEM NO: 76310 OWNER S MANUAL IMPORTANT: Read all instructions carefully before using this product. Retain this owner s manual for future reference. The specifications of this product

More information

For more information visit or contact hearx:

For more information visit   or contact hearx: USER MANUAL hearscope - Ground Floor, Building 2, Ashlea Gardens Office Park, 180 Garsfontein Road, Ashlea Gardens, Pretoria, 0081, South Africa hearscope v2. HSCP-MN-EN hearscope IFU v1.0 For more information

More information

THE TOTALLY WICKED TORNADO NC CONGRATULATIONS ON PURCHASING YOUR TOTALLY WICKED TORNADO NC ELECTRONIC CIGARETTE KIT

THE TOTALLY WICKED TORNADO NC CONGRATULATIONS ON PURCHASING YOUR TOTALLY WICKED TORNADO NC ELECTRONIC CIGARETTE KIT USER MANUAL THE TOTALLY WICKED TORNADO NC CONGRATULATIONS ON PURCHASING YOUR TOTALLY WICKED TORNADO NC ELECTRONIC CIGARETTE KIT 3 QUICK START GUIDE For those familiar with e-cigarettes, the steps below

More information

Table of Contents. Section 1 Introduction... 1 Section 2 Getting Started... 2 Section 3 Components... 5

Table of Contents. Section 1 Introduction... 1 Section 2 Getting Started... 2 Section 3 Components... 5 Table of Contents Section 1 Introduction... 1 Section 2 Getting Started... 2 Section 3 Components... 5 Meter 5 Test Strips 8 Test Devices 8 Control Strips or Control Devices 13 Section 4 Initial Setup...

More information

Thank you for purchasing the AB COASTER. Our customer service staff is ready to help and to answer any questions.

Thank you for purchasing the AB COASTER. Our customer service staff is ready to help and to answer any questions. Thank you for purchasing the AB COASTER. Our customer service staff is ready to help and to answer any questions. Our phone number is: 908-879-2713 The Ab Coaster Company, 173 Route 206, P.O. Box 9 Chester,

More information

Activated Transponder & Activator Instruction Manual

Activated Transponder & Activator Instruction Manual Activated Transponder & Activator Instruction Manual Westhold Corporation General Warranty Modules and other equipment ("Goods") purchased from Westhold Corporation are warranted against defects in materials

More information

OWNER S MANUAL. Quick Insertion Guide: INSERT EARTIP into ear canal and rotate earpiece backwards & into position CHECK FOR SEAL

OWNER S MANUAL. Quick Insertion Guide: INSERT EARTIP into ear canal and rotate earpiece backwards & into position CHECK FOR SEAL OWNER S MANUAL Quick Insertion Guide: 1 2 3 4 IDENTIFY EARPIECES marked (R) for right and (L) for left ALIGN EARPIECES at the ear canal, with cord facing forward & slightly downward INSERT EARTIP into

More information

USER S MANUAL QUESTIONS? CAUTION. Visit our website at. new products, prizes, fitness tips, and much more!

USER S MANUAL QUESTIONS? CAUTION. Visit our website at.  new products, prizes, fitness tips, and much more! Model No. WEBE44.0 Serial No. Write the serial number in the space above for future reference. USER S MANUAL Serial Number Decal QUESTIONS? As a manufacturer, we are committed to providing complete customer

More information

Bryan-Dumon Series II Rigid Bronchoscope and Stent Placement Kit USER MANUAL

Bryan-Dumon Series II Rigid Bronchoscope and Stent Placement Kit USER MANUAL Bryan-Dumon Series II Rigid Bronchoscope and Stent Placement Kit USER MANUAL Table of Contents Bryan-DUmon Series II rigid bronchoscope 1. 2. 3. 4. 5. Diagram and Overview Universal Barrel Bronchial and

More information

INSTRUCTIONS FOR USE

INSTRUCTIONS FOR USE Comfort Injects 50 Comfort-in INSTRUCTIONS FOR USE English user manual 1 Introduction Thank you for choosing the Comfort in Needle free Injection system, developed with your comfort and convenience in

More information

High Strength splicing with Ericsson

High Strength splicing with Ericsson High Strength splicing with Ericsson The High Strength Concept Fusion splicing technique has developed to such a degree that low loss splices have become the rule. However, the same cannot be said of

More information

SDS 4.0 Reference Guide

SDS 4.0 Reference Guide SDS 4.0 Reference Guide Content Important information 2 SDS 4.0 Fit and Go Box overview 3 Selecting the receiver length 4 Choosing the correct earpiece for the receiver 5 Attaching / removing the retention

More information

Product Information Packet

Product Information Packet Product Information Packet Pendulum Full Rack Product Part Number: 410706 Patents: #D562670, Patent Pending Pendulum Full Rack shown with optional pull-up arches. Table of Contents Introduction..... 1

More information

User Bulletin 7500 Fast Precision Plate Holder for MicroAmp Tube Strips

User Bulletin 7500 Fast Precision Plate Holder for MicroAmp Tube Strips User Bulletin 7500 Fast Precision Plate Holder for MicroAmp Tube Strips December 19, 2007 SUBJECT: Using MicroAmp Fast 8-Tube Strips (0.1-mL) on the 7500 Fast Precision Plate Holder for MicroAmp Tube Strips

More information

MARCY WEIGHT BENCH MWB-479. Model MWB-479. Retain This Manual for Reference OWNER'S MANUAL

MARCY WEIGHT BENCH MWB-479. Model MWB-479. Retain This Manual for Reference OWNER'S MANUAL NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Important Assembly Information MARCY WEIGHT BENCH MWB-479 Care and Maintenance Parts List Warranty

More information

Home Health Foundation, Inc. To create more permanent IV access for patients undergoing long term IV therapy.

Home Health Foundation, Inc. To create more permanent IV access for patients undergoing long term IV therapy. PROCEDURE ORIGINAL DATE: 06/99 Revised Date: 09/02 Home Health Foundation, Inc. SUBJECT: PURPOSE: MIDLINE CATHETER INSERTION To create more permanent IV access for patients undergoing long term IV therapy.

More information

MARCY PRO OLYMPIC BENCH

MARCY PRO OLYMPIC BENCH NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Important Assembly Information MARCY PRO OLYMPIC BENCH PM-70210 Care and Maintenance Parts List Warranty

More information

USER S MANUAL QUESTIONS? CAUTION. Visit our website at.

USER S MANUAL QUESTIONS? CAUTION. Visit our website at. Model No. NTCCBE950 Serial No. Write the serial number in the space above for future reference. USER S MANUAL Serial Number Decal (under seat) QUESTIONS? As a manufacturer, we are committed to providing

More information

EVER Pharma D-mine Pen Pen injector for Apomorphine 10 mg/ml

EVER Pharma D-mine Pen Pen injector for Apomorphine 10 mg/ml EVER Pharma D-mine Pen Pen injector for Apomorphine 10 mg/ml Instructions for Use with Dacepton 3 ml Cartridges Apomorphine hydrochloride hemihydrate solution for injection Subcutaneous Use TABLE OF CONTENTS

More information

USER S MANUAL QUESTIONS? CAUTION. For a great selection of new CD and MP3 workouts. Visit our website at. or call

USER S MANUAL QUESTIONS? CAUTION. For a great selection of new CD and MP3 workouts. Visit our website at.  or call Model No. RBBE950 Serial No. Write the serial number in the space above for future reference. USER S MANUAL Serial Number Decal (Under Seat) QUESTIONS? As a manufacturer, we are committed to providing

More information

POWER STATION With Fold up Bench

POWER STATION With Fold up Bench NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Important Assembly Information Care and Maintenance POWER STATION With Fold up Bench STB-98502 Parts

More information

Rev 1.0. CMA 470 Refrigerated Fraction Collector

Rev 1.0. CMA 470 Refrigerated Fraction Collector 8002778 Rev 1.0 CMA 470 Refrigerated Fraction Collector CMA 470 REFRIGERATED FRACTION COLLECTOR USER S MANUAL CONTENTS 1 INTRODUCTION... 3 2 SAFETY... 3 3 UNPACKING & ASSEMBLY... 4 3.1 Packing list...

More information

Contents.

Contents. Contents Using The Video Otoscope... 3 The Battery Operated LED Light Source... 4 Connecting the Video Otoscope... 5 Connect the LEMO Cable... 6 Wiring Diagram... 7 Specula Adapter... 8 Trouble Shooting

More information

INSTALLATION MANUAL. VIDEO Camera, Probe and Lightsource OTOSCOPES.

INSTALLATION MANUAL. VIDEO Camera, Probe and Lightsource OTOSCOPES. INSTALLATION MANUAL VIDEO Camera, Probe and Lightsource OTOSCOPES www.medrx-int.com Contents Using The Video Otoscope... 3 The Battery Operated LED Light Source... 4 Wiring Diagram - Battery Operated LED

More information

RSD SYSTEM. Owner s Manual

RSD SYSTEM. Owner s Manual RSD SYSTEM Owner s Manual RSD Parts Identification Diagram Index RSD Parts Identification Diagram Page 3 Cord Guide Page 4 Attaching the RSD Page 5 Attaching the Handle Page 6 Screw Cord Guide T-nut Handle

More information

Stratis INSTRUCTIONS FOR USE. Needle-free Injection System. 0.5mL volume (+/-5%)

Stratis INSTRUCTIONS FOR USE. Needle-free Injection System. 0.5mL volume (+/-5%) Stratis Needle-free Injection System INSTRUCTIONS FOR USE 0.5mL volume (+/-5%) Stratis English Symbols Glossary (Note: All symbols are derived from ISO 15223-1, Medical Devices - Symbols to be used with

More information

WEIGHT BENCH EXERCISER User s Manual

WEIGHT BENCH EXERCISER User s Manual Model No. 81.19.0 Serial No. Write the serial number in the space above for reference. WEIGHT BENCH EXERCISER User s Manual Serial Number Decal Assembly Operation Maintenance Part List and Drawing Sears,

More information

Owner s Manual & Exercise Guide

Owner s Manual & Exercise Guide Owner s Manual & Exercise Guide Distributed by: Thane International, Inc., La Quinta, CA 92253 Thane Direct Canada, Inc., Toronto, ON. Thane Direct UK Ltd., Admail 68, PL1 1AD w w w. t h a n e. c o m Copyright

More information

St. Jude Medical 8-Channel Adapter. Clinician's Manual

St. Jude Medical 8-Channel Adapter. Clinician's Manual St. Jude Medical 8-Channel Adapter Clinician's Manual CAUTION: Federal (USA) law restricts this device to sale by or on the order of a physician. For U.S. California Only: Proposition 65, a State of California

More information

VeriFit Irritant Smoke Generators for Respirator Fit Testing SENSITIVITY CHECK PROTOCOL. Introduction. Warnings

VeriFit Irritant Smoke Generators for Respirator Fit Testing SENSITIVITY CHECK PROTOCOL. Introduction. Warnings VeriFit Irritant Smoke Generators for Respirator Fit Testing SENSITIVITY CHECK PROTOCOL Introduction This protocol is provided to you to be used in conjunction with normal irritant smoke fit test procedures

More information

Instructions for Use Reprocessed Ethicon ENDOPATH XCEL TM Bladeless Trocar with OPTIVIEW Technology

Instructions for Use Reprocessed Ethicon ENDOPATH XCEL TM Bladeless Trocar with OPTIVIEW Technology Reprocessed by Instructions for Use Reprocessed Ethicon ENDOPATH XCEL TM Bladeless Trocar with OPTIVIEW Technology Reprocessed Device for Single Use Caution: Federal (U.S.A.) law restricts this device

More information

Align Gluco-Monitoring System (BG1) Quick Start Guide

Align Gluco-Monitoring System (BG1) Quick Start Guide EN Align Gluco-Monitoring System (BG1) Quick Start Guide WELCOME Welcome to your ihealth Align Gluco-Monitoring System (the ihealth system). The ihealth system is designed to be used with the free ihealth

More information

Successful Splicing Made Easy

Successful Splicing Made Easy Successful Splicing Made Easy Years ago fiber splicing was a difficult and finicky process that was left to the fiber guru. The splicers were expensive and temperamental. Nobody wanted to be the person

More information

MARCY ECLIPSE BE1000 STANDARD BARBELL BENCH

MARCY ECLIPSE BE1000 STANDARD BARBELL BENCH NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice MARCY ECLIPSE BE1000 STANDARD BARBELL BENCH Important Assembly Information Care and Maintenance Parts

More information

A-dec 372L or 572L Dental Light on an A-dec Performer Dental Chair INSTALLATION GUIDE

A-dec 372L or 572L Dental Light on an A-dec Performer Dental Chair INSTALLATION GUIDE A-dec 37L or 57L Dental Light on an A-dec Performer Dental Chair INSTALLATION GUIDE Contents Before You Begin.......... Remove the Covers........ Choose the Procedure...... 3 Install the Rigid Arm.......

More information

STANDARD BENCH MWB-382. Model MWB-382. Retain This Manual for Reference OWNER'S MANUAL

STANDARD BENCH MWB-382. Model MWB-382. Retain This Manual for Reference OWNER'S MANUAL NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Important Assembly Information STANDARD BENCH MWB-382 Care and Maintenance Parts List Warranty Ordering

More information

Align Gluco-Monitoring System (BG1) Quick Start Guide

Align Gluco-Monitoring System (BG1) Quick Start Guide EN Align Gluco-Monitoring System (BG1) Quick Start Guide WELCOME Welcome to your ihealth Align Gluco-Monitoring System (the ihealth system). The ihealth system is designed to be used with the free ihealth

More information

InsuPad User Manual. Charger Base The charger base can be connected by the attached USB cable to the power adapter supplied for charging.

InsuPad User Manual. Charger Base The charger base can be connected by the attached USB cable to the power adapter supplied for charging. InsuPad User Manual System overview The InsuPad is designed to improve the delivery of injected insulin into the blood by controlled warming of the area which surrounds the point of injection. The device

More information

COMPETITOR COMPETITOR WEIGHT BENCH. Model CB Retain This Manual for Reference OWNER'S MANUAL

COMPETITOR COMPETITOR WEIGHT BENCH. Model CB Retain This Manual for Reference OWNER'S MANUAL NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Important Assembly Information COMPETITOR COMPETITOR WEIGHT BENCH CB-20111 Care and Maintenance Parts

More information

36 KIDS MINI TRAMPOLINE WITH HANDRAIL. Not recommended for children under 3 years of age.

36 KIDS MINI TRAMPOLINE WITH HANDRAIL. Not recommended for children under 3 years of age. 36 KIDS MINI TRAMPOLINE WITH HANDRAIL PRODUCT MANUAL - VERSION 01.18.04 FOR AGES: 3-7 WEIGHT LIMIT: 75 Lbs 35 Kgs ADULT(S) NEEDED: TOOLS NEEDED: WARNING/ADVERTENCIA CUSTOMER SERVICE Consult a physician

More information

3M MS 2. Next Generation Modular Splicing Rigs and Maintenance Kits. Simplified Systems For All Your Multi-Pair Splicing Needs

3M MS 2. Next Generation Modular Splicing Rigs and Maintenance Kits. Simplified Systems For All Your Multi-Pair Splicing Needs 3M MS 2 Next Generation Modular Splicing Rigs and Maintenance Kits Simplified Systems For All Your Multi-Pair Splicing Needs A Complete System To Meet High-Speed Demands. In 1976, 3M introduced a series

More information

2. Before Testing Monitor Checker Test...10 Inserting Lancets into Lancing Device...11 Quality Control Testing...13

2. Before Testing Monitor Checker Test...10 Inserting Lancets into Lancing Device...11 Quality Control Testing...13 Table of Contents 1. About your HemoSmart Haemoglobin Screening System Contents of Kit...4 HemoSmart Haemoglobin Meter...5 HemoSmart Haemoglobin Test Strip...7 Adjustable Lancing Device and Lancets...8

More information

USER S MANUAL QUESTIONS? CAUTION. Visit our website at. For a great selection of new CD and MP3 workouts. or call

USER S MANUAL QUESTIONS? CAUTION. Visit our website at. For a great selection of new CD and MP3 workouts.  or call Model No. IFBE3540 Serial No. Write the serial number in the space above for future reference. USER S MANUAL Serial Number Decal (Under Seat) QUESTIONS? As a manufacturer, we are committed to providing

More information

Pocket Diagnostic Instruments. Use, Care, & Maintenance

Pocket Diagnostic Instruments. Use, Care, & Maintenance Pocket Diagnostic Instruments Use, Care, & Maintenance Thank you for choosing an ADC Diagnostic set. We re proud of the care and quality that goes into the manufacture of each and every diagnostic instrument

More information

Set-up Instructions. MANUFACTURED BY COMMUNICATIONS-APPLIED TECHNOLOGY CO., INC. RESTON, VA. CAGE CODE: 0EEY2

Set-up Instructions. MANUFACTURED BY COMMUNICATIONS-APPLIED TECHNOLOGY CO., INC. RESTON, VA. CAGE CODE: 0EEY2 Set-up Instructions C-AT Level A/B Radio Interface with: Push-to-Talk Assembly, Shaped Audio Throat Microphone Bi-aural Speaker Assembly (two configurations) MANUFACTURED BY COMMUNICATIONS-APPLIED TECHNOLOGY

More information

AquaJogg Hydro Treadmill

AquaJogg Hydro Treadmill AquaJogg Hydro Treadmill PART #: F-WXAQJG 330 LB. [150 kg] MAXIMUM WEIGHT CAPACITY MANDATORY LEAVE THIS MANUAL WITH TREADMILL OWNER To assemble your equipment read entire manual and follow all instructions.

More information

Standard Operating Procedure for cannulation

Standard Operating Procedure for cannulation Standard Operating Procedure for cannulation Effective date: 26.07.2017 Review due date: 31.03.2019 Original Author Name: Richard Metcalfe Position: PhD Student Date: 05.12.2012 Reviewer Name: Pippa Heath

More information

Longevity Offset and Oblique Liners. Surgical Technique

Longevity Offset and Oblique Liners. Surgical Technique Longevity Offset and Oblique Liners Surgical Technique Longevity Offset & Oblique Liners Surgical Technique 1 Introduction Complete Acetabular System Joint instability is an important issue in both primary

More information

USER'S MANUAL QUESTIONS?

USER'S MANUAL QUESTIONS? Model No. WL000 QUESTIONS? USER'S MANUAL As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions or find that there are missing or damaged parts, we will

More information

Universal Monitor User s Guide. Insertion Instructions Care and Maintenance Hearing Care Information Warranty

Universal Monitor User s Guide. Insertion Instructions Care and Maintenance Hearing Care Information Warranty Universal Monitor User s Guide Insertion Instructions Care and Maintenance Hearing Care Information Warranty UM Monitor Care and Maintenance Congratulations on your choice of Westone UM monitors! The information

More information

WEIGHT SYSTEM EXERCISER User s Manual

WEIGHT SYSTEM EXERCISER User s Manual Model No. 831.14934.0 Serial No. Write the serial number in the space above for reference. WEIGHT SYSTEM EXERCISER User s Manual Serial Number Decal Assembly Operation Maintenance Part List and Drawing

More information

COMPRESSOR NEBULIZER MODEL: JB USER S MANUAL

COMPRESSOR NEBULIZER MODEL: JB USER S MANUAL COMPRESSOR NEBULIZER MODEL: JB0112-062 USER S MANUAL Read this manual before operating the nebulizer Save these instructions for future reference Caution: Federal law restricts this device to sale by or

More information

INSTRUCTIONS FOR USE TYMLOS (tim lows ) (abaloparatide) injection, for subcutaneous use

INSTRUCTIONS FOR USE TYMLOS (tim lows ) (abaloparatide) injection, for subcutaneous use INSTRUCTIONS FOR USE TYMLOS (tim lows ) (abaloparatide) injection, for subcutaneous use Instructions for Use Read and follow this Instructions for Use so that you inject TYMLOS pen the right way. Call

More information

limbsandthings.com Advanced Catheterisation Trainer User Guide For more skills training products visit Limbs & Things Ltd.

limbsandthings.com Advanced Catheterisation Trainer User Guide For more skills training products visit Limbs & Things Ltd. Advanced Catheterisation Trainer Product No: 60150 User Guide For more skills training products visit limbsandthings.com Limbs & Things Ltd. Sussex Street, St Philips Bristol, BS2 0RA, UK sales@limbsandthings.com

More information

EXERTEC FLAT BENCH ETC-2.1. Model ETC-2.1. Retain This Manual for Reference OWNER'S MANUAL IMPEX INC.

EXERTEC FLAT BENCH ETC-2.1. Model ETC-2.1. Retain This Manual for Reference OWNER'S MANUAL IMPEX INC. NOTE: Please read all instructions carefully before using this product Safety Notice Hardware Identifier Assembly Instruction EXERTEC FLAT BENCH ETC-2.1 Parts List Warranty Ordering Parts Model ETC-2.1

More information

CAREFULLY READ ALL INSTRUCTIONS PRIOR TO USE

CAREFULLY READ ALL INSTRUCTIONS PRIOR TO USE CAREFULLY READ ALL INSTRUCTIONS PRIOR TO USE INDICATIONS FOR USE The LATERA Absorbable Nasal Implant is indicated for supporting upper and lower lateral nasal cartilage. CAUTION: Federal law restricts

More information

Cardiva Catalyst III INSTRUCTIONS FOR USE

Cardiva Catalyst III INSTRUCTIONS FOR USE Cardiva Catalyst III INSTRUCTIONS FOR USE IFU 2469 Rev. G CAUTION Federal (USA) law restricts this device to sale by or on the order of a physician. For single use only GRAPHICAL SYMBOLS ON THE CARDIVA

More information

WEIGHT BENCH MWB Model MWB Retain This Manual for Reference OWNER'S MANUAL

WEIGHT BENCH MWB Model MWB Retain This Manual for Reference OWNER'S MANUAL NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice WEIGHT BENCH MWB-50100 Important Assembly Information Care and Maintenance Parts List Warranty Ordering

More information

CHAIR ASSEMBLY & CARE GUIDE

CHAIR ASSEMBLY & CARE GUIDE CHAIR ASSEMBLY & CARE GUIDE For maximum effectiveness and safety, read instructions and important tips before using the Pilates PRO Chair. important safety information assembly instructions use and care

More information

Owner s Manual. Customer Service (Option 3) Monday-Friday 6:00am to 5:00pm Pacific OR Support

Owner s Manual. Customer Service (Option 3) Monday-Friday 6:00am to 5:00pm Pacific OR  Support Owner s Manual Customer Service 888-678-2476 (Option 3) Monday-Friday 6:00am to 5:00pm Pacific OR Email Support parts@stairmaster.com IMPORTANT: READ ALL ASSEMBLY INSTRUCTIONS AND SAFETY PRECAUTIONS BEFORE

More information

COMPACT BENCH MWB Model MWB Retain This Manual for Reference OWNER'S MANUAL

COMPACT BENCH MWB Model MWB Retain This Manual for Reference OWNER'S MANUAL NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice COMPACT BENCH MWB-20100 Important Assembly Information Care and Maintenance Parts List Warranty Ordering

More information

E. SelectTech 5.1 Bench Owner s / Assembly Manual

E. SelectTech 5.1 Bench Owner s / Assembly Manual 000-6189.080118.E SelectTech 5.1 Bench Owner s / Assembly Manual Congratulations on your commitment to fitness and your purchase of the Bowflex SelectTech 5.1 Bench. Before assembling your Bowflex SelectTech

More information

Autopen 24 is an easy to use insulin injection pen, designed for use with 3.0ml sanofi aventis insulin cartridges. Compatible with all pen needles*.

Autopen 24 is an easy to use insulin injection pen, designed for use with 3.0ml sanofi aventis insulin cartridges. Compatible with all pen needles*. Instructions for use English Autopen 24 is an easy to use insulin injection pen, designed for use with 3.0ml sanofi aventis insulin cartridges. Compatible with all pen needles*. PLEASE FOLLOW THESE STEP-BY-STEP

More information

Quick Start Guide. Congratulations on your journey to better hearing

Quick Start Guide. Congratulations on your journey to better hearing Quick Start Guide Congratulations on your journey to better hearing At Starkey, we believe that to hear better is to live better. Get the most out of your hearing aids Please visit starkey.com/care for

More information

Quick Start Guide. Congratulations on your journey to better hearing

Quick Start Guide. Congratulations on your journey to better hearing Quick Start Guide Congratulations on your journey to better hearing At Starkey, we believe that to hear better is to live better. Get the most out of your hearing aids Please visit starkey.com/care for

More information