SKELETAL PROTHESIS with Vertys Prothesis Excel / Plus heat-curing resin
|
|
- Mildred Cole
- 5 years ago
- Views:
Transcription
1 SKELETAL PROTHESIS with Vertys Prothesis Excel / Plus heat-curing resin What you need for this working: EQUIPMENT VERTYS SPLIT CAST & GUM APOLIX AR.GO FURBO ALU BIG APOLIX CU-BA (Curing Basket) MIXING KIT VERTYS DYNAMO BLOCK VERTYS ARTIC LINK 1F + 1M VERTYS SIRIN- GHE + HANDLE HELP CONSUMABLES SIS EXCEL LIQUID SIS EXCEL CLASSIC PINK VEINED VERTYS ORANGE SPECIAL LUBE SIS PLUS LIQUID SIS PLUS CLASSIC PINK VEINED VERTYS ORANGE PLUS VERTYS EASY PUTTY 5 Kg HIGH SECURITY FLUID VERTYS LUBE 1/5
2 INTRO The dental impressions arrive in the laboratory already disinfected and together with the work requirements, medical office, data and references about the pacient or an identification code. The operator responsible for acceptance checks the completeness of the data, records the work and completes the technical sheet The operator verifies the material with which the impressions were taken and establishes the type of material to be used to develop the models. Class IV gypsum is recommended Mix the vaccum-sealed gypsum, in accordance with the proportions and time-table indicated by the manufacturer An electric shaker could be helpful to cast the impression The model plater socket must be realized on the adequate VERTYSYSTEM s systematic Split Cast. As an alternative, VERTYS ARTIC LINK M base may be used. Before disconnecting the model from the impression, wait for the hardening time indicated by the manufacturer A. MODEL PREPARATION The developped model is desengaged, trimmed and squared The model should have a minimum heel of 15 mm of height and a 5 mm lateral border Place the models in articulator through the VERTYS ARTIC LINK F bases Construction of the skeleton as usual Perform tooth assembly and complete the wax modeling of the saddles With a wax casting plug,diameter of 3/5 mm, connect the saddle of the skeleton (always in the front).fix the ends of the plugs with the wax. If possible always place the wax plug on the metal part, in case of a upper model on the palatine plaque, in the lower following the lingual bar. This allows, once the skeleton is finished, and cut with a disk separating the two ends, to easily remove the resin plug. B. FIRST TEMPLATE-MOLD REALIZATION WITH VERTYS ORANGE PLUS Prepare about 20 g (10 g A + 10 g B) of HIGH SECURITY FLUID silicone and brush with a small brush all the teeth, including the occlusal part. We recommend also covering the gingival collars in waxand! - Apply the remaining material with a spatula - Let it harden for about 8/10 min. - This material allows us to obtain a precision of the gingival modeling and an extraordinary tooth stability! Prepare about 60 g (30 g A + 30 g B) of VERTYS ORANGE PLUS silicone Knead for 20 sec.and adapt the silicone on the skeleton covering it completely Be careful to cover both wax parts and metal parts (hooks and plate/bar) If the plaster model presents, above all vestibularly, holes in undercuts, eliminate them with VERTYS EASY PUTTY silicone Insert the model, with VERTYS ORANGE PLUS mask, in the APOLIX heat press - without water - at temperature 0 C / zero degrees celsius (with thermostat deactivated) - at the pressure of at least 2 atmospheres, maximum 6 atmospheres - let the silicone harden for 7 minutes Once hardened, put the model on the Split Cast of the FURBO ALU BIG / SMALL muffle Insert the steel spacer needed in the 3 guide rods of the muffle Now insert the muffle cover on the 3 guide rods and check that there are not interferences and contacts In particular, make sure that there is a space of at least 1 cm between the template-mold and the cover of the muffle Once hardening occured, apply the VERTYS ORANGE SPECIAL LUBE insulation spray on the silicone VERTYS EASY PUTTY, with which the sub-squares have been eliminated C. BOXAGGIO WITH VERTYS EASY PUTTY SILICONE Knead 160 g (80 g A + 80 g B) of VERTYS EASY PUTTY for at least 20 sec. Adapt about half of the mixture on the inside of the FURBO ALU BIG / SMALL muffle cover and use the remaining VERTYS EASY PUTTY for the boxing of the second stamp-stain, containing the model and the product Insert the muffle cover into the appropriate guide rods and compress until the cover is fitted with the spacers on the 3 gide rods Immediately block the muffle cover with the appropriate stop nuts Tighten with the VERTYS VERTYS DYNAMO BLOCK dynamometric nut First compress the silicone leaked from the top slot of the muffle, and immediately after, the silicone leaked out at the base of the model You will obtain the adaptation of the silicone on the second mask and a perfect sealing This step must be carried out with the utmost care in order to prevent the leakage of the resin during the injection phase To check the perfect closure of the FURBO ALU BIG/SMALL, the spacers must not rotate on the guide rods Wait for the hardening of the VERTYS EASY PUTTY for about 7 minutes After hardening, unscrew the nuts, remove the muffle cover from the 3 guide rods, and extract the model from the first silicone mask 2/5
3 D. PREPARATION OF THE INLET AND OUTLET HOLES IN THE SILICONE DURING THE INJECTION PHASE Take the muffle cover with the second mold template inserted and, with the supplied reamers, drill two holes in the silicone in correspondence of the two ends of the molding, starting from the inside of the template mold, until it comes out of the muffle cover In this way the inlet and outlet channels for the acrylic resin injection will be created Entry hole with large reamer # Output hole with small reamer # Using the correct reamer ensures that the hole diameter exactly matches the diameter of the syringe tip that will be used for resin injection The exit hole must always be done with the small reamer Using a scalpel, perform a flaring on the silicone in correspondence with both holes This will create two wells that will serve to contain the resin reserve when injected E. WASHING AND DEGREASING THE PLASTER MODEL ANDACRYLIC THEET Carefully wash and degrease the model and any hooks with steam or hot water Immerse the model in water at a temperature of C Leave it soak for 10 minutes to allow saturation In this way it is avoided that the plaster can absorb the resin monomer when it is injected Open the cover of the HELP # basket and insert the teeth into the specially created seats, thus avoiding to confuse them when the washing is finished. Screw the HELP lid and proceed with the degreasing by steaming or boiling in hot water Dry with compressed air F. PREPARATION OF THE FURBO ALU BIG / SMALL MUFFLE FOR THE RESIN INJECTION Create mechanical/chemical retentions, channel shapped, to acrylic teeth Reinsert the teeth into their seats, inside the second silicone mold template Remove the model from the lukewarm water and insulate it with a very thin layer of VERTYS LUBE alginic insulation Let the model dry Opacify the retentions with the VERTYS OPAK PINK Insert the Skelethon in the first silicone mold mask. The prepared model, must now be inserted into the second silicone mold mask and brought together with VERTYS SPLIT CAST of the FURBO ALU BIG / SMALL muffle. Make sure that the necessary spacers are inserted in the 3 guide rods Insert the appropriate muffle lid in the appropriate guide rods and slide it until it contacts the steel spacers Close it with the fixing muffle bolts. Tighten with the VERTYS VERTYS DYNAMO BLOCK dynamometric nut G. PREPARATION OF THE RESIN FOR VERTYS PROTHESIS EXCEL / PLUS INJECTION Weigh the necessary amount of powder and liquid of the acrylic resin for orthodontics, in the proportions indicated in the instruction fot the use of VER- TYS PROTHESIS EXCEL / PLUS Approximately 10 g of powder and 6 g of liquid are required for a medium-sized partial denture Pour the liquid in the MIXING CUP Then pour the powder and mix it for 10 seconds. let it rest for another seconds Pour the resin into a one time use syringe,versare ora la resina in una siringa monouso da 30 cc, having the foresight to close the exit hole with a finger Insert the plunger and turn the syringe upside down Push the plunger until any air bubbles will escape Maintain the pressure on the plunger until you obtain a small resin leakage from the tip of the syringe. The resin is ready when it assume a filamentous consistency. The consistency time and injection time may vary, depending even significantly, based on the environmental conditions H. INJECTION PROCEDURE FOR THE ACRYLIC RESIN With one hand hold the muffle inclined at 45 so that the outlet hole is lower than the inlet hole By doing so you, air bubbles will be avoided during the injection phase Insert now the syringe tip in the lower inlet hole and slowly and continuously push the plunger until there is a leakage of the resin from the top hole (the injection time is usually of 1/1,30 min.) Always maintaining the syringe plunger under pressure, straighten the muffle, place it on the workbench and continuous the injection and pressure phase It is important not to remove all the resin, but leave the groove previously created full Slowly remove the syringe but always maintain the pressure Immediately also fill the second reserve groove The injection phase is now completed, the injection phase is now completed and in correspondence of the inlet and outlet grooves, there are now visible the two reserve buttons The muffle can be placed into the heat press once the resin of the button becomes slightly elastic and it doesn t stick to the fingers 3/5
4 I. ACRYLIC RESIN POLYMERIZATION Insert the FURBO ALU BIG/SMALL muffle into the APOLIX heat press by paying attention to: 1. The water, inside the heat press, must be at room temperature 2. The water lever must not be over the muffle cover ( it is very important that the two inlet and outlet holes of the resin are not covered) 3. The pressure must not be over 2 atmospheres For the temperature and the polymerization times please follow the instruction for the resin VERTYS PROTHESIS EXCEL / PLUS resin Once the polymerization has been completed, remove the muffler from the APOLIX heat press (or pressure cooker) Remove the two resin buttons, in correspondence of the grooves, by breaking them with the help of plaster knife or by cutting them with a diamond disc Open the muffle and remove the model and artefact from the silicone template mask Remove the two imput and output plugs with a cutter Cut the resin connection plug J. CONTROL IN THE ARTICULATOR Insert the model together with the bite in the AR.GO articulator for a check ( or in the articulator that is usually used) Proceed with the finishing touch and polishing SILICONE WEIGHTS MATERIALS First mask mold: 60g VERTYS ORANGE PLUS First mask mold: VERTYS ORANGE PLUS Second mask mold: Insulators - VERTYS LUBE Boxaggio: 160g VERTYS EASY PUTTY Optional: 20g HIGH SECURITY FLUID Boxaggio: VERTYS EASY PUTTY (70 Shore) Resin: VERTYS PROTHESIS EXCEL / PLUS PROCESSING TIME First mask mold: minimum manipulation 20 sec. Hardening in the heat press 7 min. Second mask mold: Boxaggio: minimum manipulation 20 sec. Hardening 7 min. Model saturation in water: a 40 C at least 10 min Resin proccessing time: Polymerization: mixing: rest: injection time: C per 30 min. in ASTERIX 10 sec. 15/20 sec. 1 min. SILICONE TOTAL TOTAL TIME TOTAL RESIN 160g VERTYS EASY PUTTY Processing 20 min. 10g Powder 6-7g Liquid 100g VERTYS ORANGE PLUS Polymerization 30 min. 4/5
5 TO COMPLETE THE WORKFLOW WITH MATERIALS THAT ARE USEFUL TO IMPROVE THE QUALITY OF FINAL ARTIFACT, CONSULT KIT LAVORAZIONI TABLES ON THE WEBSITE In order to extend the working time of our Putty silicones, we advesi the use of the liquid # VERTYS RETARD (One drop corresponds to one more minute of processing) ATTENTION: assumes no responsibility for the final result, if all the consumables of the VERTYSYSTEM are not used! The times, quantities and temperatures of this protocol, relates only to these materials. 5/5
PARTIAL MOBILE DENTURE with Vertys Prothesis Excel / Plus termo-polimerizing resin
PARTIAL MOBILE DENTURE with Vertys Prothesis Excel / Plus termo-polimerizing resin What you need for this working: EQUIPMENT 10-0010 VERTYS SPLIT CAST & GUM 10-100 APOLIX 10-3000 AR.GO 10-2501 FURBO ALU
More informationTRANSFER OF THE FUNCTIONALISED TEMPORARY transfer of the functionalized temporary from the oral cavity to the verticulator
TRANSFER OF THE FUNCTIONALISED TEMPORARY transfer of the functionalized temporary from the oral cavity to the verticulator What you need for this working: EQUIPMENT 10-0010 VERTYS SPLIT CAST & GUM 10-401
More informationUniversal Plunger Loc Attachment
Universal Plunger Loc Attachment www.preat.com 800-232-7732 Universal Plunger Loc Complete Universal 7.5mm length TI plunger attachment. Compatible with Lew Passive and Swiss Loc NG. 1.5mm plunger, 7.5mm
More informationOT EQUATOR CASTABLE Single Attachment for Overdentures
OT EQUATOR CASTABLE Single Attachment for Overdentures pick-up impression OT EQUATOR PROFILE CASTABLE MALE ATTACHMENT individual tray RETENTIVE CAPS OT EQUATOR HOUSING VIOLET CAP RIGID RETENTION (2.7Kg)
More informationSTEP-BY-STEP-ANLEITUNG
STEP-BY-STEP-ANLEITUNG VON TECHNIKERN FÜR TECHNIKER LABORATORY PROCEDURES, STEP BY STEP BY TECHNICIANS FOR TECHNICIANS Eclipse junior Laboratory Procedures, Step by Step* Splints Drilling Stents Temporaries
More informationLABORATORY PROCEDURES, STEP BY STEP
LABORATORY PROCEDURES, STEP BY STEP BY TECHNICIANS FOR TECHNICIANS Eclipse Laboratory Procedures, Step by Step* Dentures with cast-metal frameworks Combination dentures Complete dentures Splints Drilling
More informationVIP Partner Laboratory (PL) Process Flow
VIP Partner Laboratory (PL) Process Flow 1. VIP Software 2. CT Scan Appliance 3. CT Scan Clinician purchases VIP for PL fabricates CT Scan Appliance Patient submitted for scans treatment planning purposes
More informationAnnotation to the lesson 21 Topic: Methods of provisory crowns fabrication. Chair-side technique. Evaluation of
Annotation to the lesson 21 Topic: Methods of provisory crowns fabrication. Chair-side technique. Evaluation of crown fitting quality Contemporary methods of restoration of tooth tissues pathology, using
More informationReference to primary publication Properties of alginates in ZWP 4/2014 Xantalgin Crono - Introduction
Reference to primary publication in ZWP 4/2014 Dr. Marcus Holzmeier, Wuerzburg Xantalgin Crono - Highly accurate alginate impressions. Introduction Even today when digital impression techniques are gaining
More informationHeight* FC width Prep depth RC width 4.0mm+ 4.3mm N/A 6.3mm
STERN ERA IMPLANT ABUTMENT Summary Resilient precision overdenture attachment. Universal hinge with vertical movement. Titanium abutment, nylon male. Manufactured for most popular screw and cylinder implants.
More information1. Visually survey the cast for discrepancies and surface defects. 2. Remove surface defects and fill unnatural indentations.
PROCEDURE CHECKLIST: SURVEY AND DESIGN 1. Visually survey the cast for discrepancies and surface defects. 2. Remove surface defects and fill unnatural indentations. 3. Visually survey cast to determine
More informationPreci Clix Instructions for Ball Retained Overdenture Attachments
www.preat.com 800-232-7732 Preci Clix Instructions for Ball Retained Overdenture Attachments Dentist Direct Placement Technique #1293 / 1297 In one appointment, an existing removable partial denture may
More informationFrequent use for the preparation of prosthetic products
laboratory use Frequent use for the preparation of prosthetic products Silicones gain more and more use for the preparation of prosthetic products. ERGAMIX addition silicone (polyvinylsiloxane) and ERGASIL
More informationProduct Information. Meliodent The solution for every denture Effective material from a proven partner. Giving a hand to oral health.
Product Information Meliodent The solution for every denture Effective material from a proven partner Giving a hand to oral health. Meliodent products from Kulzer. A range of impressive cost effective
More informationDenture Duplicator Flask
Denture Duplicator Flask Package Contents REF 0398 One Flask REF 0395 One Flask, Jet Tooth Shade Powder: 2x45 g Net Wt., Jet Denture Repair Powder: 2x100 g Net Wt., Jet Liquid: 236 ml Net Vol., Silicone
More informationUDELL DENTAL LABORATORY Instructions for Use
DALLA BONA Summary Cylindrical Dalla Bona Rigid precision attachment. Radicular telescopic stud. Adjustable frictional retention. Gold alloy male (Elitor) and female (OSV). Fixation: Male - soldered to
More informationPreci Clix Instructions for Ball Retained Overdenture Attachments
www.preat.com 800-232-7732 Preci Clix Instructions for Ball Retained Overdenture Attachments Dentist Direct Placement Technique In one appointment, an existing removable partial denture may be converted
More informationRelining and Rebasing of complete denture
Relining and Rebasing of complete denture It is the procedures used to resurface the tissue-side of a denture with new material layer, thus producing an accurate adaptation to the denture foundation area.
More informationFR Attachment Instructions Removable Partial Dentures
www.preat.com 800-232-7732 FR Attachment Instructions Removable Partial Dentures 1 2 Adjust the master cast on mounting platform of the surveyor to the chosen angle of insertion. Check to be sure the tooth
More informationident CT Guide Protocol
ident CT Guide Protocol The ident computer planning and iguide production starts with the CT Guide. This is a simple device which can be made by a dental technician, but it is essential that it is made
More informationThe fitting process of SomnoGuard
The fitting process of SomnoGuard Hints to complement the actual user instructions AP Tomed Dr. Toussaint GmbH, 31.07.2010 Needed accessories Spray disinfectant for all working tools Boling water bath
More informationInvisible Retainer with Single-Tooth Pontic Fabrication Technique (Multi-Tooth Pontic Procedure also available)
Invisible Retainer with Single-Tooth Pontic Fabrication Technique (Multi-Tooth Pontic Procedure also available) Safety glasses should be worn for all lab procedures as well as gloves when handling acrylics.
More informationFace-Bow Instructions
M Panadent Corporation 580 S. Rancho Avenue Colton, California 92324, USA Tel: (909) 783-1841 USA & Canada (800) 368-9777 The following procedure is followed when Panadent Bite-Tab compound discs are used
More informationThe fitting process of SomnoGuard AP. Hints to complement the user instructions
The fitting process of SomnoGuard AP Hints to complement the user instructions Essential equipment and instruments Spray disinfectant for all instruments Boling water bath Water boiler Disposable gloves
More informationINJECTION TECHNOLOGY FOR DENTURE PRODUCTION
INJECTION TECHNOLOGY FOR DENTURE PRODUCTION Ofer Darey, master-technician, consultant, Sun Rise Laboratories, Israel Interest to production of removable dentures from thermoplastic materials, which is
More informationInstruction Guide. Today is the day you change the way you live with dentures. How to Apply DenSureFit Soft Silicone Reline Material
Instruction Guide Today is the day you change the way you live with dentures. How to Apply DenSureFit Soft Silicone Reline Material Dentist-grade soft silicone denture reline materialnow available in an
More informationUDELL DENTAL LABORATORY Instructions for Use PREAT Precision Attachments
Indications Instructions The Locator Root Attachment is designed for use with overdentures or partial dentures, retained in whole or in part by endodontically treated roots in the mandibular or maxilla.
More informationIMPRESSION PROCEDURES TRAINING MANUAL
IMPRESSION PROCEDURES TRAINING MANUAL 01 01 A.B. DENTAL A.B. Dental is proud to present this impression taking procedure protocol. This manual explains, step by step, the procedure while using A.B. Dental
More informationRhino Clear Sprint Atomizer
Visit us online to view our wide range of sinus therapy medications for use with the Rhino Clear Sprint atomizer. www.woodlandhillspharmacy.com 20631 Ventura Blvd, Ste 305 Woodland Hills, CA 91364 Phone:
More informationHex-Lock Abutment System. Restorative Manual
System Restorative Manual 32 Restorative options with s s are manufactured from titanium alloy and used as the support foundation for single- or multiple-unit cement-retained, partially edentulous fixed
More informationQuintessence copyright. You are not allows to show or use this file for any other purpose than personal use.
Quintessence copyright. You are not allows to show or use this file for any other purpose than personal use. P. Tardieu November 2005 2. Radiological Templates A radiological template is a radiopaque duplicate
More informationSS Implant System 2013 PROSTHETIC PROCEDURE
SS Implant System 2013 PROSTHETIC PROCEDURE Contents TS Implant System Cement retained restoration 06 Cement-retained bridges with the Solid abutment system (non-modified abutment) 16 Cement-retained bridges
More informationSimpleLine II Surgical / Prosthesis Manual
SimpleLine II Surgical / Prosthesis Manual SimpleLine II SURGICAL MANUAL Surgical Drill Sequence 04 Fixture Installation 05 Fixture Connection 06 Surgical Kit Maintenance 08 Warnings 09 04 SimpleLine ll
More informationInvisible Retainer with Multi-Tooth Pontic Fabrication Technique (Single-Tooth Pontic Procedure also available)
Invisible Retainer with Multi-Tooth Pontic Fabrication Technique (Single-Tooth Pontic Procedure also available) Safety glasses should be worn for all lab procedures as well as gloves when handling acrylics.
More informationOcclusal Splint Fabrication Technique
Occlusal Splint Fabrication Technique Safety glasses should be worn for all lab procedures as well as gloves when handling acrylics. Items featured in this technique are found on the last page. 1 Mount
More informationTECHNICAL DATASHEET POUR TYPE ACRYLIC RESIN PDFTPT-082
TCHNICAL DATASHT POUR TYP ACRYLIC RSIN 1 PRODUCT OVRVIW Methacrylate polymers have enjoyed great popularity in dentistry because they are easily processed by using relatively simple techniques; they have
More informationDiagnosis 220 Temporary Filling Carrier. Periodontics Periodontal Curette / Sharpener
Diagnosis 220 Temporary Filling Carrier Periodontics Periodontal Curette / Sharpener Conservative Treatment Composite Syringe / Rubber Dam Punch / Clamp Forceps / Rubber Dam Kit / Reamer Stand / Endodontic
More informationHow something small, can make such a big difference!! Your best choice in overdenture
How something small, can make such a big difference!! Your best choice in overdenture Why? Kerator has the worldʼs most powerful competitiveness in overdenture attachment system. KERATOR was chosen over
More informationThe Reinforced Removable Retainer
The Reinforced Removable Retainer Abstract The aim of this paper is to present a new type of orthodontic removable retainer, which is of great help to the orthodontist as well as to the patient. The procedures
More informationDigital Impression Scanning
Digital Impression Scanning Table of Contents Using ScanIt Orthodontics (Recommended Software) Software Settings... 1 Control Panel... 1 System Settings... 1 Export Format... 1 Filling Out Patient Information...
More informationTreatment Options for Restoring Edentulous Jaws using One- and Two-Piece Implants from Implant Direct Int l
Treatment Options for Restoring Edentulous Jaws using One- and Two-Piece Implants from Implant Direct Int l Two-Piece ReActive Tri-Lobe Implants with Multi-Unit Abutments One-Piece ScrewIndirect Implants
More informationSteps in construction of an interim dental implant-supported hybrid prosthesis:
Steps in construction of an interim dental implant-supported hybrid prosthesis: 1. Identify the desired tooth position (natural teeth, dentures, etc.) in order to plan for Implant placement. 2. Make impressions
More information2. Gap closure and replacement of the missing tooth 35 with directly modelled bridge region 34-36
GrandTEC Test Kit Dear User, This Test Kit has been put together to enable you to test GrandTEC on the model before using it in a clinical situation. GrandTEC is a resin-impregnated glass fibre strip.
More informationChapter 5: Checking and Maintaining Ultrasound Equipment
Chapter 5: Checking and Maintaining Ultrasound Equipment Care and Cleaning (BB1564-AJ) Chapter 5: Checking and Maintaining Ultrasound Equipment 45 Ultrasound equipment requires regular checks and maintenance.
More informationAustenal PermaSoft Soft Denture Liner
Austenal PermaSoft Soft Denture Liner Directions for Use Laboratory Technique Chairside Technique Indications for Use: Intended for use as soft liner for acrylic full dentures and the acrylic saddle areas
More informationIMPRESSION MATERIALS
IMPRESSION MATERIALS Function of Impression Materials To make a negative copy of an oral structure single tooth, quadrant, or arch edentulous or dentulous Negative copy must be accurate to produce an accurate
More informationUse of the Sicat Surgical Guide In Reconstruction of the Hemi-Mandilectomy Patient
Use of the Sicat Surgical Guide In Reconstruction of the Hemi-Mandilectomy Patient Dr. Michael J. Maginnis Dr. Glenn E. Appleton Prosthodontics and Family Dentistry www.drsmanda.com Sarcoma of the Mandible
More informationTable of Contents. Flexi-Overdenture Characteristics
A s with Flexi-Post Flexi-Overdenture has the unique threaded split shank that creates maximum retention with minimum stress to the root. It is manufactured in stainless steel for the direct/non-coping
More informationProsthodontic Procedure
Prosthodontic Procedure TSA TSA Advance Regeneration Implant Systems CAD-CAM Digital Solutions Services IMPORTANT: BEFORE USING Phibo The innovative and patented design of the Phibo implant systems incorporates
More informationRemovable Prosthodontics. Complete Denture Procedures for a Team Approach
Department of General Dentistry Division of Removable Prosthodontics Complete Denture Procedures for a Team Approach For Competency #9 1 Rev. April 2010 Ronni A. Schnell, D.M.D., M.A.G.D. Complete Denture
More information(Instruction For Use) Vertex ThermoSens Rigid
(Instruction For Use) Page 1 of 5 Vertex ThermoSens Rigid User content: Page Page Preface 1 Pretreatment flask 2 1. Introduction 1 Processing times 2 2. Description and effects 1 Injection 3 3. Contra-indication
More informationPatient Information Publications Warren Grant Magnuson Clinical Center National Institutes of Health
Warren Grant Magnuson Clinical Center National Institutes of Health What is a subcutaneous injection? A subcutaneous injection is given in the fatty layer of tissue just under the skin. A subcutaneous
More informationWe express. Acrylics rich in color and texture. GENERAL PRODUCT INFORMATION
We express Saint Basil Cathedral, Rusia. Visual riches for a changing aesthetic. Acrylics rich in color and texture. GENERAL PRODUCT INFORMATION Acrylic resins result from a mixture of powdered polymers
More informationFITTING CROWN TO EXISTING PARTIAL DENTURE
FITTING CROWN TO EXISTING PARTIAL DENTURE Here are a series of photographs to illustrate how you, when prepping a crown that has to fit an existing removable denture, can make a pattern resin matrix in
More informationTECHNICAL GUIDE. For use with CEREC
TECHNICAL GUIDE For use with CEREC THE FUTURE AND SOLUTION OF INNOVATIVE ZIRCONIA FEATURES TRANSLUCENCY SIMILAR TO NATURAL TOOTH ENAMEL BY SPEED SINTERING The collaboration of Kuraray Noritake Dental s
More information3D Printing Full Dentures with the Form 2
FORMLABS APPLICATION GUIDE: 3D Printing Full Dentures with the Form 2 Today, 50 million dentures are produced globally each year, but only 1 percent are produced using digital tools. Traditional denture
More informationProsthodontic Procedure
Prosthodontic Procedure TSH BNT Regeneration Implant Systems CAD-CAM Digital Solutions Services Important: before using Phibo The innovative and patented design of the Phibo implant systems incorporates
More informationDURATEMP Temporary Crown & Bridge Material. Temrex Corporation October 2009
DURATEMP Temporary Crown & Bridge Material Temrex Corporation October 2009 DURATEMP Temporary Crown & Bridge Material Overview Product Characteristics Physical Properties Case Report Instructions Ordering
More informationProsthodontic Procedure
Prosthodontic Procedure Aurea Regeneration Implant Systems CAD-CAM Digital Solutions Services AUREA IMPLANT SYSTEM PROSTHODONTIC PROCEDURE IMPORTANT BEFORE USING AUREA IMPLANT SYSTEM The innovative and
More informationListing of Standards By Task
Orthodontics Listing of Standards By Task ORTHODONTICS 1. Disinfect the impression and/or model 2. Evaluate the prescription for completeness 3. Document changes to the prescription and/or design requirements
More information18 INSTRUCTIONS FOR THE DOCTOR Clinical management of CA CLEAR ALIGNER. Dr. Pablo Echarri
18 INSTRUCTIONS FOR THE DOCTOR Clinical management of CA CLEAR ALIGNER Dr. Pablo Echarri All cases were carried out by Dr. Pablo Echarri. All the laboratory work was carried out by Ladent laboratory, and
More informationUDELL DENTAL LABORATORY Instructions for Use AND ERA-RV
STERN ERA AND ERA-RV Summary Extracoronal semi-precision attachment. Universal hinge with vertical resiliency. Nylon male, plastic pattern female. Female is waxed into the pattern of the abutment restoration
More informationTJF-160F/VF Cleaning and Disinfection Checklist
TJF-160F/VF Cleaning and Disinfection Checklist TJF-160F/VF Cleaning and Disinfection Checklist This checklist is used to evaluate and confirm if cleaning and disinfection of the TJF-160F/VF has been performed
More informationTooth preparation for posterior fi xed partial denture (FPD) Tooth preparation for anterior fi xed partial denture (FPD)
CHAPTER 17 Tooth preparation for posterior fi xed partial denture (FPD) 1 Defi nition and feature of FPD 2 Actual sequence of tooth preparation for posterior FPD Verify abutment teeth Occlusal guide groove
More informationHistory and innovation
LEADERSHIP History and innovation Since KROMOPAN was created it has been an incredible break through in dentistry. Thanks to a careful selection of raw materials and well-advanced manufacturing processes
More informationIndividual Tools for Controlling and Positioning Porcelain Veneers: Easychecker The Aesthetic Key Ralf Barsties, CDT and Dr.
Individual Tools for Controlling and Positioning Porcelain Veneers: Easychecker The Aesthetic Key Ralf Barsties, CDT and Dr. Franka Meuter 58 Spectrum dialogue Vol. 11 No. 4 April 2012 Ceramic veneers
More informationRemovable Prosthodontics. Complete Denture Procedures for a Team Approach in the Home
Department of General Dentistry Division of Removable Prosthodontics Complete Denture Procedures for a Team Approach in the Home For Competency #9 1 Rev. April 2010 Ronni A. Schnell, D.M.D., M.A.G.D. and
More informationSICAT Surgical Guides. Fabrication of Radiographic Templates Conebeam/CT scanning parameters 3-D Implant planning Ordering Surgical Guides
SICAT Surgical Guides Fabrication of Radiographic Templates Conebeam/CT scanning parameters 3-D Implant planning Ordering Surgical Guides 2 Table of contents 1. SICAT Surgical Guides... 4 1.1 Important
More informationLecture:6 dental material dr. Aseel Mohammed
4. Zinc oxide eugenol impression material: It's described as a rigid, mucostatic, irreversible (set by chemical reaction) and hydrophobic impression material. We have 2 types of zinc oxide eugenol impression
More informationListing of Standards By Task
Listing of Standards By Task PARTIAL DENTURES 1. Disinfect the impression and/or model 2. Evaluate the prescription for completeness 3. Document changes to the prescription 4. Evaluate the impression or
More informationWorking Instructions. Vita System. 3D - Master. VITA shade taking VITA shade communication VITA shade reproduction VITA shade control
Working Instructions VITA shade taking VITA shade communication VITA shade reproduction VITA shade control Date of issue 3-09 Teeth Veneering Materials Vita System Service 3D - Master Equipment All-Ceramics
More informationRestoring Straumann implants. with Locator abutments.
Restoring Straumann implants with Locator abutments. 1 1 Straumann is the industrial partner of the ITI (International Team for Implantology) in the areas of research, development, and education. Contents.
More informationSupplies. Online. Reliability at a great value. Dentaurum. shop.dentaurum.com
Impression material Page 296 Laboratory accessories Page 298 Appliance containers and accessories Page 300 Orthodontic study / demonstration models Page 302 Other Page 307 292 . Reliability at a great
More informationAward Matrix HPVC Dental Consumables
Award Matrix HPVC2017-123 Dental Consumables Effective 1st March 2017 3M Australia Pty Ltd Product Sub Category Number & 1 BURS 1.01 BURS DIAMOND FINISHING AND POLISHING A A A A A A A 1 BURS 1.02 BURS
More informationZEST DANVILLE MATERIALS PERIOSCOPY
ZEST DANVILLE MATERIALS PERIOSCOPY Attachment Processing Material is easy to use and predictable when processing attachments into full and partial overdentures,using either a chairside or laboratory procedure.
More informationRemovable Partial Dentures
Removable Partial Dentures Replacement of missing teeth Fixed partial denture Removable partial denture Complete removable Transitional denture Partial removable Implant retained prosthodontics No prosthetic
More informationUnBreakable. Arian Deutsch, CDT
UnBreakable Arian Deutsch, CDT UnBreakable is there such a material? In Dentistry, the quest for a material that blends with nature both esthetically and functionally has been a long journey indeed. Many
More informationPRODUCT CATALOG. Since 1985» Simple. Predictable. Profitable.
PRODUCT CATALOG Since 1985» Simple. Predictable. Profitable. 2014 IMPLANTS HEALING PLUG INSERTERS COLLAGEN PRODUCTS 3.0mm Well Integra-CP Part No. DIAMETER LENGTH Price 345-306 4.5mm mm $280.00 345-308
More informationSolid Zirconia Full-Arch Implant Prosthesis (Protocol C All-CAD with Multi-Unit Abutments) BruxZir. FIRST Appointment. The BruxZir
(Protocol C All-CAD with Multi-Unit Abutments) Step-by-Step Restorative Protocol C The BruxZir Full-Arch Implant Prosthesis offers a fixed, all-zirconia implant solution for edentulous patients desiring
More informationDevice Technical File
Device Technical File ContactPro Matrix System Instructions for Use 1.0 Product Description A. For placement of restorations in the posterior area of the oral cavity, the Microbrush ContactPro Sectional
More informationHow To Use White With Style Whitening Kit
How To Use White With Style Whitening Kit Instructions The instructions below will show you how to use the White with Style Kit. You will first mold your mouth trays to fit your mouth. Once they are fit
More informationPRO-V IDS Kit. Bisco. Instructions for Use. Provisional Restorative System
Bisco PRO-V IDS Kit Provisional Restorative System Instructions for Use U.S. Patent: 7,748,980; 8,106,110 IN-199R3 Rev. 5/16 BISCO, Inc. 1100 W. Irving Park Rd. Schaumburg, IL 60193 U.S.A. 847-534-6000
More informationLOCATOR F-Tx SEATING AND REMOVAL TOOL PROCEDURES ADDENDUM
1 LOCATOR F-Tx SEATING AND REMOVAL TOOL PROCEDURES ADDENDUM INSTRUCTIONS FOR USE DESCRIPTION Wire and Lever Wrench Tip Wrench Seating and Removal Tool Seating Tip Removal Tip with Threaded Adapter The
More informationBryan-Dumon Series II Rigid Bronchoscope and Stent Placement Kit USER MANUAL
Bryan-Dumon Series II Rigid Bronchoscope and Stent Placement Kit USER MANUAL Table of Contents Bryan-DUmon Series II rigid bronchoscope 1. 2. 3. 4. 5. Diagram and Overview Universal Barrel Bronchial and
More informationThere is one thing different. Everything.
There is one thing different. Everything. THE MODEL MAKER THE SET-UP MODEL MAKER THE OCCLUSAL PLANE REFERENCE THE SURGICAL MODEL ACCURACY DEVICE Precise - Easy - Clean - Economical - Multi Purpose - Essential
More informationARAB AMERICAN UNIVERSITY. Lab. Manual. Prosthetic Dentistry1; Removable Prosthodontics. 3 rd year
ARAB AMERICAN UNIVERSITY Lab. Manual Prosthetic Dentistry1; Removable Prosthodontics 3 rd year Department of Fixed and removable prosthetic Dentistry Faculty of Dentistry 2012/2013 Course Instructor Dr.
More informationConvex Array Transducer
User Guide Type 8823 Convex Array Transducer English BB1740-C June 2012 For Professional Users Only BK MEDICAL Mileparken 34 2730 Herlev Denmark Tel.:+45 4452 8100 / Fax:+45 4452 8199 www.bkmed.com Email:
More informationIntroducing the Pala 3D-printed Denture
ebook Create your best workflow and optimize production with cara 3D printing technology. Introducing the Pala 3D-printed Denture Powered by cara Print 4.0 and dima Print materials. < 2 hrs. Giving a hand
More informationPegasus. Schottlander Denture Base Ranges. Part of the Award Winning Enigma & Natura Denture Systems
Schottlander Denture Base Ranges Part of the Award Winning Enigma & Natura Denture Systems Colour Tone Gingival Colouring Acrylic High-Base High Impact Denture Base Pegasus Plus Denture Base, Plus Repair
More informationeliminate interlocking with new QUick Up method
eliminate interlocking with new QUick Up method TissUe colored implant pick-up system THe new QUick Up TecHniQUe in a complete system eliminates THe risk of interlocking In many cases the fit of full dentures
More informationSurgical Guide Technique
Surgical Guide Technique Safety glasses should be worn for all lab procedures as well as gloves when handling acrylics. Items featured in this technique are found on the last page. 1 Select a denture tooth
More information3. PATIENT POSITIONING & FRACTURE REDUCTION 3 8. DISTAL GUIDED LOCKING FOR PROXIMAL NAIL PROXIMAL LOCKING FOR LONG NAIL 13
Contents IMPLANT FEATURES 2 1. INDICATIONS 3 2. PRE-OPERATIVE PLANNING 3 3. PATIENT POSITIONING & FRACTURE REDUCTION 3 4. INCISION 4 5. ENTRY POINT 4-6 6. PROXIMAL NAIL INSERTION 6-7 7. PROXIMAL LOCKING
More informationTransbond PLUS Color Change Adhesive Lunch and Learn
Unitek Bonding System Transbond PLUS Color Change Adhesive Lunch and Learn Transbond PLUS Color Change Adhesive Agenda What is Transbond PLUS Color Change Adhesive? Why Transbond PLUS Color Change Adhesive?
More informationThe Hanau Modular Articulator System 194 Fixed 11 cm width, adjustable Radial-Shift Guidances. Illustrated Instruction Manual
The Hanau Modular Articulator System 194 Fixed 11 cm width, adjustable Radial-Shift Guidances Illustrated Instruction Manual A Study Case for Occlusal Analysis This instruction manual illustrates the
More informationRestoring Ocular Esthetics Using Ocular Prosthesis
Case Report Restoring Ocular Esthetics Using Ocular Prosthesis Dr. Kalavathi S.D 1*, Dr. Arvind Moldi 2**, Dr. Phaneendra Kumar 3* * Senior lecturer, ** Professor & HOD, 1 Department of Prosthodontics,
More informationDENTAL MATERIALS STUDY GUIDE
DENTAL MATERIALS STUDY GUIDE WORKSHEET Dentalelle Tutoring www.dentalelle.com Study Guide for Dental Materials Dentalelle Tutoring 1. When completing a large composite restoration, how should the composite
More informationALPROLIX Coagulation Factor IX (Recombinant), Fc Fusion Protein INSTRUCTIONS FOR USE Do not Do not YOUR KIT CONTAINS:
ALPROLIX Coagulation Factor IX (Recombinant), Fc Fusion Protein INSTRUCTIONS FOR USE Read the Instructions for Use before you start using ALPROLIX and each time you get a refill. There may be new information.
More informationDPI Luting Cement. DPI Restorative Cement
DPI Luting Cement DPI Luting Cement is Type I glass ionomer white luting cement. DPI glass ionomers are remarkably biocompatible and can be safely used in deep cavities provided the pulp is not exposed,
More informationUNICLIP DIRECTIONS FOR USE REF C226U - 0,8 MM / 1 MM FOR DENTAL USE ONLY. FISDR / F EN / 11 / updated 06/2016 1/7
UNICLIP FOR DENTAL USE ONLY DIRECTIONS FOR USE REF C226U - 0,8 MM / 1 MM EN FISDR / F19 02 31.EN / 11 / 2001 - updated 06/2016 1/7 1) Indications for use These products have to be used only in hospital
More informationTriad Visible Light Cure System
Triad Visible Light Cure System Triad Visible Light Cure System Denture Relines & Repairs For Complete Control from Design to Delivery Dentsply Sirona s unique Visible Light Cure Technology delivers maximum
More information