TECHNICAL DATASHEET POUR TYPE ACRYLIC RESIN PDFTPT-082
|
|
- Alice Johnson
- 5 years ago
- Views:
Transcription
1 TCHNICAL DATASHT POUR TYP ACRYLIC RSIN 1 PRODUCT OVRVIW Methacrylate polymers have enjoyed great popularity in dentistry because they are easily processed by using relatively simple techniques; they have the capacity to provide essential properties and the necessary characteristics to use them in oral restoration. One of the main applications is for the manufacture of dental restorations such as total, partial, and removable prostheses. 2 CHARACTRISTICS OF TH ACRYLIC RSIN The acrylic resin for pouring is used in the manufacture of total and partial prostheses. This acrylic resin allows to prepare dental rehabilitation in only one hour, thus facilitating the work time in the laboratory; besides, it provides better finishing wince the waxing is copied in duplicate liquid material instead of using gypsum, therefore, the prostheses is cleaner. 3 COMPOSITION INFORMATION Polymer components: Self-polymerizing acrylic (Type II). Poly (Methyl Methacrylate). Pigments. Polyester (If a reference with mottled appearance is required). Additives. Components of self-polymerizing monomers (Type II). Methyl Methacrylate. Dimethacrylate ethylene glycol. Amine-type chemical initiator. 1 de 7
2 TCHNICAL DATASHT POUR TYP ACRYLIC RSIN 4 PRODUCT PROPRTIS The physical properties of polymers are measured in the Quality Control Laboratory by using specialized and calibrated equipment, based on the ISO :2013 standard. The following table shows the most relevant physical properties. Parameter Requirement xperimental Result Absorption It must not exceed 32 µg/mm Solubility It must not exceed 8.0 µg/mm Flexural strength Minimum 60 MPa 62.6 Flexural module Minimum 1500 MPa 1800 Residual Monomer Maximum 4.5% in weight US AND APPLICATIONS The composition of the self-polymerizing acrylic resins for use by means of the pouring technique (monomer and polymer) Veracril Pour, Opti-Cryl Pour is indicated for the preparation of dental restorations such as total, partial, and removable prostheses. They have the following characteristics: The time required for the preparation of the dental restoration is one hour, and it allows for optimal work time for pouring. They are resistant to fractures. They require a thermal treatment by means of pressurizing equipment. They are asily polished, allowing to recover their gloss. Vertical and linear contractions that the acrylic structure may suffer are avoided by using the appropriate ratio of polymer and monomer. 2 de 7
3 TCHNICAL DATASHT POUR TYP ACRYLIC RSIN 6 PRODUCT QUALITY ASSURANC Acrylic resins are manufactured with raw materials of the highest quality, through a completely standardized productive process certified under ISO 9001:2008 and ISO 13485:2003. Besides, the compliance with the requirements of the ISO :2013 standard is verified in the Quality Control Laboratory for the finished product by means of specialized equipment. Water absorption and solubility: Verifies the amount of water that the acrylic resins absorb or the amount of weight they lose when immersed in water. Acrylic is insoluble in saliva or in any other fluid present in the mouth. Porosity: The processed acrylic has a surface free of imperfections and porosities. Bending strength and Flexure Module: They measure the degree of deformation of acrylic resins to be able to support occlusal forces exerted at the time of use. Additionally, they measure the force a resin supports until fracture, which guarantees their good clinical performance. Transluscency: An object must be visible when placed on the opposite side of the acrylic test piece. Residual Monomer: The content of monomer that may remain during the preparation of the prosthesis must be minimum in order to ensure absence of irritation in the mouth tissues. 7 INSTRUCTIONS FOR US WORKING TCHNIQU. WAXING AND FLASKING Use the conventional waxing and teeth placing technique. Place the pouring weirs properly for the acrylic resin. Condition the items necessary for flasking, using the flask for the pouring technique. Hydrate the model in water at ambient temperature for an approximate time of 30. Fix the model to the base of the flask with the aid of plastiline. Verify that the model does not have retentions on the base and/or around the bottom of the groove. 3 de 7
4 TCHNICAL DATASHT POUR TYP ACRYLIC RSIN Follow the instructions indicated in the silicon or hydrocolloid duplicate material. WAX LIMINATION Wasth the teeth and the gypsum model with hot water to remove the wax with the aid of metal grid. After having the teeth completely clean, place them properly on their position. APPLICATION OF TH GYPSUM ACRYLIC SPARATOR Apply a thin layer of Novafoil gypsum separator on the gypsum model after washing the wax. Brush very well to avoid leaving excess material. TH PROPORTIONS OF US FOR TH MIX AR AS FOLLOWS: For the preparation of the mix, use 2.5 parts of polymer (powder) and 1 measure of monomer (liquid) measured in volume. PRPARATION OF TH MIX The mix is prepared in an appropriate container (glass or porcelain container). 4 de 7
5 TCHNICAL DATASHT POUR TYP ACRYLIC RSIN Mix softly in a criss-cross pattern continuously to avoid generation of air and to ensure that the polymer particles are incorporated completely to the monomer, until obtaining a semi-liquid mixture. (honey-like consistency). POURING. Pour in the flask through the central orifice, taking the precaution of filling the three orifices (the flask must comply with the requirements for the technique) and leave to rest for 3 to 4 minutes. POLYMRIZING Place the flask inside the pressurizing device in vertical position. Caution must be taken so that water does not touch the acrylic resin. Close the pressuring device and apply 30 pounds of pressure at a temperature of 60 C during 60 minutes. Let the flask cool down before deflasking. POLISHING Use the regular procedure according to the dental laboratory techniques. 5 de 7
6 TCHNICAL DATASHT POUR TYP ACRYLIC RSIN 8 COMMRCIAL PRSNTATIONS Self-polymerizing acrylic polymer: Jars of: 60 g, 500 g Plastic drum: 2.5 kg, 10 kg Self-polymerizing liquid acrylic: High-density polyethylene plastic package of 32 oz. High-density polyethylene plastic package of 8 oz. 9. SHLF LIF Self-polymerizing acrylic polymer: Four (4) years. Self-polymerizing acrylic monomer: Two (2) years 6 de 7
7 TCHNICAL DATASHT POUR TYP ACRYLIC RSIN 10. STORAG AND PRSRVATION CONDITIONS Storage: Keep the product in a cool, well ventilated place (air atmosphere). Keep away from all flame or spark source. Do not smoke. Keep away from heat and direct sunlight. Store away from oxidizing agents, acids, bases, and polymerizing initiators. Do not store for extended periods of time. 7 de 7
We express. Acrylics rich in color and texture. GENERAL PRODUCT INFORMATION
We express Saint Basil Cathedral, Rusia. Visual riches for a changing aesthetic. Acrylics rich in color and texture. GENERAL PRODUCT INFORMATION Acrylic resins result from a mixture of powdered polymers
More informationISO 1567 INTERNATIONAL STANDARD. Dentistry Denture base polymers. Art dentaire Polymères pour base de prothèses dentaires. Third edition
INTERNATIONAL STANDARD ISO 1567 Third edition 1999-02-15 Dentistry Denture base polymers Art dentaire Polymères pour base de prothèses dentaires A Reference number Contents 1 Scope...1 2 Normative references...1
More informationISO INTERNATIONAL STANDARD. Dentistry Base polymers Part 1: Denture base polymers
INTERNATIONAL STANDARD ISO 20795-1 First edition 2008-08-01 Dentistry Base polymers Part 1: Denture base polymers Art dentaire Polymères de base Partie 1: Polymères pour base de prothèses dentaires Reference
More informationRelining and Rebasing of complete denture
Relining and Rebasing of complete denture It is the procedures used to resurface the tissue-side of a denture with new material layer, thus producing an accurate adaptation to the denture foundation area.
More informationRELINING AND REBASING
RELINING AND REBASING Relining: The process used to resurface the tissue side of a denture with new material layer, thus producing an accurate adaptation to the denture foundation area. Rebasing: The laboratory
More informationEvaluation of bond to Enigma High Impact Denture Base
page 13 Evaluation of bond to Enigma High Impact Denture Base 1 Assignment Evaluation of the bonding strength between each layer of artificial tooth material and denture base resin at the site of fracture
More informationDepartment of Prosthodontics, Faculty of Dentistry, Mahidol University, Bangkok, Thailand
Dental Journal Mahidol Dental Journal Original Article Dimensional stability of compression and injection molding denture bases in long and short curing procedures Noppavan Nagaviroj, Krantarat Wanitchanont,
More informationPegasus. Schottlander Denture Base Ranges. Part of the Award Winning Enigma & Natura Denture Systems
Schottlander Denture Base Ranges Part of the Award Winning Enigma & Natura Denture Systems Colour Tone Gingival Colouring Acrylic High-Base High Impact Denture Base Pegasus Plus Denture Base, Plus Repair
More information1. RPD Acrylic portions = denture teeth (DT), denture base (DB) (and veneering)
REMOVABLE PROSTHODONTICS Page 1 Lecture: "Removable Partial Denture Acrylic Materials" INTRODUCTION A. Overview: 1. RPD Acrylic portions = denture teeth (DT), denture base (DB) (and veneering) 2. Potential
More informationBEGO PMMA Multicolor Processing information for CAD/CAM-produced restorations
BEGO PMMA Multicolor Processing information for CAD/CAM-produced restorations Partners in Progress CAD/CAM-PRODUCED RESTORATIONS FROM BEGO PMMA Multicolor High-performance PMMA with color gradient BEGO
More informationINJECTION TECHNOLOGY FOR DENTURE PRODUCTION
INJECTION TECHNOLOGY FOR DENTURE PRODUCTION Ofer Darey, master-technician, consultant, Sun Rise Laboratories, Israel Interest to production of removable dentures from thermoplastic materials, which is
More informationAN INJECTION MOULDING DEVICE, IMPROVING THE EXISTING INJECTION SYSTEM FOR ACRYLIC DENTURE FABRICATION
ORIGINAL ARTICLES AN INJECTION MOULDING DEVICE, IMPROVING THE EXISTING INJECTION SYSTEM FOR ACRYLIC DENTURE FABRICATION Kalina Georgieva, Metodi Abadjiev Department of Prosthetic Dental Medicine and Orthodontics,
More informationSTEP-BY-STEP-ANLEITUNG
STEP-BY-STEP-ANLEITUNG VON TECHNIKERN FÜR TECHNIKER LABORATORY PROCEDURES, STEP BY STEP BY TECHNICIANS FOR TECHNICIANS Eclipse junior Laboratory Procedures, Step by Step* Splints Drilling Stents Temporaries
More information(Instruction For Use) Vertex ThermoSens Rigid
(Instruction For Use) Page 1 of 5 Vertex ThermoSens Rigid User content: Page Page Preface 1 Pretreatment flask 2 1. Introduction 1 Processing times 2 2. Description and effects 1 Injection 3 3. Contra-indication
More informationDURATEMP Temporary Crown & Bridge Material. Temrex Corporation October 2009
DURATEMP Temporary Crown & Bridge Material Temrex Corporation October 2009 DURATEMP Temporary Crown & Bridge Material Overview Product Characteristics Physical Properties Case Report Instructions Ordering
More informationIMPRESSION MATERIALS
IMPRESSION MATERIALS Function of Impression Materials To make a negative copy of an oral structure single tooth, quadrant, or arch edentulous or dentulous Negative copy must be accurate to produce an accurate
More informationAcknowledgments Introduction p. 1 Objectives p. 1 Goals p. 2 History of Dental Materials p. 3 The Oral Environment p. 4 Characteristics of the Ideal
Preface p. v Acknowledgments p. vii Introduction p. 1 Objectives p. 1 Goals p. 2 History of Dental Materials p. 3 The Oral Environment p. 4 Characteristics of the Ideal Dental Material p. 5 Quality Assurance
More informationAnnotation to the lesson 21 Topic: Methods of provisory crowns fabrication. Chair-side technique. Evaluation of
Annotation to the lesson 21 Topic: Methods of provisory crowns fabrication. Chair-side technique. Evaluation of crown fitting quality Contemporary methods of restoration of tooth tissues pathology, using
More informationUDELL DENTAL LABORATORY Instructions for Use
DALLA BONA Summary Cylindrical Dalla Bona Rigid precision attachment. Radicular telescopic stud. Adjustable frictional retention. Gold alloy male (Elitor) and female (OSV). Fixation: Male - soldered to
More informationAn evaluation of the hardness of flexible Denture Base Resins
ORIGINAL STUDY An evaluation of the hardness of flexible Denture Base SHEEBA GLADSTONE, SUDEEP S, ARUN KUMAR G Department of Prosthodontics, PMS College of Dental Science & Research, Golden Hills, Vattappara,
More informationPetrolatum. Stage 4, Revision 1. Petrolatum is a purified semi solid mixture of hydrocarbons obtained from petroleum.
1 001-1208PDG.pdf Petrolatum Stage 4, Revision 1 Definition Petrolatum is a purified semi solid mixture of hydrocarbons obtained from petroleum. It may contain a suitable antioxidant. Description and Solubility
More informationEffect of Thickness and Recycling on Transverse Strength of Relined Acrylic Resin Denture
ISSN: 1812 1217 Effect of Thickness and Recycling on Transverse Strength of Relined Acrylic Resin Denture Base. Nadira A Hatim BDS, MSc ( Prof) Aliaa W AL-Omari BDS, MSc (Asst Lec) Department of Prosthetic
More informationAvaDent Bonding Procedure Results: The AvaDent bond exceeds ADA requirements.
Tests Summary: AvaDent Bonding Procedure Results: The AvaDent bond exceeds ADA requirements. AvaDent Color Stability Results: AvaDent is more color stable than conventional dentures. AvaDent Acrylic Porosity
More informationRPD ACRYLIC MATERIALS
RPD ACRYLIC MATERIALS Stephen C. Bayne Department of Operative Dentistry School of Dentistry University of North Carolina Chapel Hill, NC 27599-7450 7450 Now that we have examined the cast metal frameworks
More informationTECHNICAL GUIDE. For use with CEREC
TECHNICAL GUIDE For use with CEREC THE FUTURE AND SOLUTION OF INNOVATIVE ZIRCONIA FEATURES TRANSLUCENCY SIMILAR TO NATURAL TOOTH ENAMEL BY SPEED SINTERING The collaboration of Kuraray Noritake Dental s
More informationrigidity of polymer, icrease thermal and wear resistances and decrease water sorption and solubility.
د.شيماء POLYMERS polymer is a chemical compound consisting of giant molecule formed by the union of many (poly) smaller repeatingn parts (mers). Monomer (one part): It is a molecule that forms the basic
More informationM-PM DISC DIGITAL PRECISION BRILLIANT AESTHETIC
M-PM DISC DIGITAL PRECISION BRILLIANT AESTHETIC M-PM DISC BIOCOMpATIBLE, DurABLE, versatile, AESThETIC Merz Dental pmma Discs are industrially made of highly cross-linked filler and fibre free OMp-N -
More informationlec: Dental material dr. Aseel Mohammed Filling material
Filling material Filling material: the material that is used to replace a missing part of the tooth which may result from dental caries, trauma or abrasion. It can be divided in to: 1. Direct filling materials:
More informationThe product must be only used by specifically trained personnel and under the relevant application by proven techniques.
Instruction manual Intended use: DD Bio ZX² monolith zero Liquids are indicated for coloring of pre-sintered Dental Direkt Zirconia milling blanks for the manufacture of dental restorations. Application:
More informationMaterial Safety Data Sheet
1 Material Safety Data Sheet MSDS0061 revised 18-MAY-2002 "PERSPEX" CLEAR CAST ACRYLIC SHEET CHEMICAL PRODUCT/COMPANY IDENTIFICATION "PERSPEX" IS A REGISTERED TRADEMARK OF LUCITE INTERNATIONAL INC. Material
More informationallinone... unbelievable? But true! Picture: Dr. Thano Kristallis
allinone... unbelievable? But true! Picture: Dr. Thano Kristallis A well-made provisional is the basis of a successful restorative treatment 2 It is desirable that a provisional system is strong and durable,
More informationIvoBase Material. The innovative denture base material. Tissue friendly, tough, predosed
Material The innovative denture base material Tissue friendly, tough, predosed Denture base material of The innovative denture base material Material The fabrication of every quality prosthetic appliance
More informationKEY PRODUCT FOR HL SAFETY DATA SHEET
January 2012 KEY PRODUCT FOR HL SAFETY DATA SHEET SECTION 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product name Synonym Use Chemical formula Registration numbers Manufacturer/Supplier Address Key
More informationOliNano Seal Professional prophylaxis for long-term protection
Professional prophylaxis for long-term protection NEW The patented formula of silicone polymer NANO Technology General information Dental health is one of the main factors to maintain overall health, and
More informationFR Attachment Instructions Removable Partial Dentures
www.preat.com 800-232-7732 FR Attachment Instructions Removable Partial Dentures 1 2 Adjust the master cast on mounting platform of the surveyor to the chosen angle of insertion. Check to be sure the tooth
More informationArtic Posteriors 30 U 30 L 32 U 32 L 30 U 30 L 32 U 32 L 30 U 30 L 32 U 32 L. Jump to Product Item Numbers
Artic Posteriors 28.9 8.4 0 30 U 30 L 30.7 33.1 9.1 8.8 0 32 U 32 L 34.8 9.2 10 30 U 30 L 29.4 8.8 31.0 7.9 10 32 U 32 L 32.1 9.5 35.3 8.7 20 30 U 30 L 29.2 7.6 31.0 6.9 20 32 U 32 L 31.4 9.0 33.5 7.5
More informationOfficial Journal of the European Union REGULATIONS
L 30/2 6.2.2015 REGULATIONS COMMISSION REGULATION (EU) 2015/174 of 5 February 2015 amending and correcting Regulation (EU) No 10/2011 on plastic materials and articles intended to come into contact with
More information: Corian Joint Adhesive Kit - Component A
This SDS adheres to the standards and regulatory requirements of Great Britain and may not meet the regulatory requirements in other countries. 1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE
More informationSteps in construction of an interim dental implant-supported hybrid prosthesis:
Steps in construction of an interim dental implant-supported hybrid prosthesis: 1. Identify the desired tooth position (natural teeth, dentures, etc.) in order to plan for Implant placement. 2. Make impressions
More informationThe Puzzle of OSHA Compliance and Infection Control in the Dental Laboratory. The Puzzle of OSHA Compliance in the Dental Laboratory
The Puzzle of OSHA Compliance and Infection Control in the Dental Laboratory The Puzzle of OSHA Compliance in the Dental Laboratory The Bloodborne Pathogen Standard: 29 CFR 1910.1030 1991/2001 The Hazard
More informationDenture Duplicator Flask
Denture Duplicator Flask Package Contents REF 0398 One Flask REF 0395 One Flask, Jet Tooth Shade Powder: 2x45 g Net Wt., Jet Denture Repair Powder: 2x100 g Net Wt., Jet Liquid: 236 ml Net Vol., Silicone
More informationAim of this study is to analyse the flexural strength of resin denture base which is incorporated with carbon nano
ISSN: 0975-766X CODEN: IJPTFI Available Online through Research Article www.ijptonline.com ANALYSING FLEXURAL STRENGTH OF RESIN DENTURE BASE, INCORPORATED WITH CARBON NANO PARTICLES S.Suvitha* 1, Dr.V.Ashok
More informationUnBreakable. Arian Deutsch, CDT
UnBreakable Arian Deutsch, CDT UnBreakable is there such a material? In Dentistry, the quest for a material that blends with nature both esthetically and functionally has been a long journey indeed. Many
More informationThe Aerosol Dispensers Directive. Labelling Requirements
The Aerosol Dispensers Directive Labelling Requirements The Aerosol Dispensers Directive Labelling Requirements The Aerosol Dispensers Directive Labelling Requirements by Charlotte Blackburn, Ph.D., Chemical
More informationCOLOURS ON CERAMIC PRODUCTS FOR DENTAL USE
COLOURS ON CERAMIC PRODUCTS FOR DENTAL USE BTEETH : COLOUR LINE FOR DENTAL CERAMICS ZIRCONIA The technological evolution of dental laboratories will be increasingly based on the use of innovative materials
More informationCompressor Nebulizer System
MedPro The Professional Choice Le choix des professionnels MedProTM MC Compressor Nebulizer System 705-445 Instruction Manual Index 1. Introduction...2 2. Product Identification...2 3. Important Safeguards...3
More information-SQA-SCOTTISH QUALIFICATIONS AUTHORITY. Hanover House 24 Douglas Street GLASGOW G2 7NG NATIONAL CERTIFICATE MODULE DESCRIPTOR
-SQA-SCOTTISH QUALIFICATIONS AUTHORITY Hanover House 24 Douglas Street GLASGOW G2 7NG NATIONAL CERTIFICATE MODULE DESCRIPTOR -Module Number- 0069146 -- -Superclass- PF -Title- DENTURE REPAIR AND REBUS/RELINE
More informationProsthetic V. Removable dentures I.
Prosthetic V. Removable dentures I. Removable dentures Partial Complete (full) lenka.roubalikova@tiscali.cz 2 Prosthetic dentistry replacement of Damaged teeth reconstruction of the crown (inlays, crowns)
More informationMATERIAL SAFETY DATA SHEET (MSDS)
MATERIAL SAFETY DATA SHEET (MSDS) HEALTH: 2 FLAMMABILITY: 1 REACTIVITY: 1 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product Name: Trade Name: Codes and colours: Manufacturer name: Ultraviolet light
More information1. PRODUCT NAME 2. SUPPLIER 3. CONTACT FOR PRODUCT INFORMATION OR EMERGENCY. 4. RECOMMENED USE Surfacing Material
1. PRODUCT NAME 2. SUPPLIER Basix Solid Surface Basix Surfaces 28241 Crown Valley Pkwy. Ste. F #297 Laguna Niguel, CA 92677 Tel: 888-719-1126 3. CONTACT FOR PRODUCT INFORMATION OR EMERGENCY Michelle Kraushaar
More informationDentistry Ceramic materials
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 6872 Fourth edition 2015-06-01 Dentistry Ceramic materials Médecine bucco-dentaire Matériaux céramiques Reference number ISO 2015 Provläsningsexemplar
More informationLABORATORY PROCEDURES, STEP BY STEP
LABORATORY PROCEDURES, STEP BY STEP BY TECHNICIANS FOR TECHNICIANS Eclipse Laboratory Procedures, Step by Step* Dentures with cast-metal frameworks Combination dentures Complete dentures Splints Drilling
More informationFDA > CDRH > CFR Title 21 Database Search
Page 1 of 10 FDA Home Page CDRH Home Page Search CDRH A-Z Index Contact CDRH 510(k) Registration Listing Adverse Events PMA Classification CLIA CFR Title 21 Advisory Committees Assembler Recalls Guidance
More informationDH220 Dental Materials
DH220 Dental Materials Lecture #5 Prof. Lamanna RDH, MS Restorative Dentistry: Glass Ionomer Bird & Robinson p.740-741 I. Use Liner Base Luting agent Restorative material: Class III, V, & eroded/abraded
More informationSafety Data Sheet. according to Regulation (EU) No. 1907/ Identification of the substance/preparation and of the company/undertaking
Print date: 12.04.2011 MSDS: Page 1 of 5 1. Identification of the substance/preparation and of the company/undertaking MSDS-ID: Company/undertaking identification Company name: Street: Place: Fahltskamp
More informationISO INTERNATIONAL STANDARD. Dentistry Reversible-irreversible hydrocolloid impression material systems
INTERNATIONAL STANDARD ISO 13716 First edition 1999-05-01 Dentistry Reversible-irreversible hydrocolloid impression material systems Art dentaire Systèmes de produits pour empreintes à base d'hydrocolloïdes
More informationAn Evaluation on the Flexural Strength of Heat Cure Polymethyl methacrylate Denture Base Resin with and without Reinforcement of Polyethylene Fiber
Vol. 1/No. 1/January-June, 2018 Original Research An Evaluation on the Flexural Strength of Heat Cure Polymethyl methacrylate Denture Base Resin with and without Reinforcement of Polyethylene Fiber Pathak
More informationSafety Data Sheet. according to Regulation (EC) No 1907/2006. SECTION 1: Identification of the substance/mixture and of the company/undertaking
Sterngold Dental, LLC Page 1 of 5 SECTION 1: Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier EZ Pickup 10ml 1.2. Relevant identified uses of the substance
More informationProtect-All Rapid Weld (Part B) Vendor. Contact: Phone: Web:
1 Page 1 of 5 PRODUCT AND COMPANY IDENTIFICATION Manufacturer Manufactured Exclusively for Vendor 5585 North Huron Avenue Oscoda, MI 48750 Contact: Phone: Info-Trac 1-800-535-5053 Contact: Phone: Web:
More informationINSTRUCTIONS FOR USE AND CARE
DIAMONDS INSTRUCTIONS FOR USE AND CARE DIAMONDS, MULTI-USE, FRICTION GRIP Quala Diamonds are a rotary cutting device made of stainless steel and coated with diamond particles on the working end. It is
More informationMaterial Safety Data Sheet PERMABOND MM115
Material Safety Data Sheet PERMABOND MM115 Revision Number: 1 Issue date: 04/23/10 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product name: PERMABOND MM115 Telephone: 732-868-1372 Product type: Anaerobic
More informationPulpdent Corporation Revision Date: January 1, 2014
1.0 Commercial Product Name and Supplier 1.1 Commercial product name / designation Kool-Dam Heatless Liquid Dam & Block Out Resin 1.2 1.2.2 1.2.3 Application / Use SIC Use Category Dental material for
More informationAn Alternative Approach for Fabrication of a Hollow Maxillary Complete Denture: A Case Report
IOSR Journal of Dental and Medical Sciences (IOSR-JDMS) e-issn: 2279-0853, p-issn: 2279-0861.Volume 15, Issue 4 Ver. IX (Apr. 2016), PP 68-72 www.iosrjournals.org An Alternative Approach for Fabrication
More informationAn Obturator With A Soft Touch: A Case Report
An Obturator With A Soft Touch: A Case Report Dr. Puneet Batra Abstract:- Factors that affect the management of maxillary defects are the presence of teeth, amount of remaining support area and defect
More informationMATERIAL SAFETY DATA SHEET
Page 1 of 5 MATERIAL SAFETY DATA SHEET 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product Identification Product Name: Savin Toner Type 5570 Black Product Number: 887997 (9852) Chemical Name: mixture
More informationColourf low. light cured dental flowable composite
Colourf low light cured dental flowable composite DENTAL LIFE SCIENCES (mfg) Ltd. Unit A3, Wigan Enterprise Court, Wigan Enterprise Park, WN2 2LE United Kingdom www.dentallifesciences.com Colourf low flowable
More information"Artless solution to resolve the problem of retention in resorbed alveolar ridge cases"
Article ID: ISSN 2046-1690 "Artless solution to resolve the problem of retention in resorbed alveolar ridge cases" Peer review status: No Corresponding Author: Dr. Khurshid Mattoo, Assistant Professor,
More informationOur story. All products are made by Stomadent Dental Lab
Our story Since 2000, Stomadent Dental Laboratory has been a great and reliable partner to hundreds of dental professionals and labs throughout the United States. With your help, we have become a full-service
More information1. Introduction Technical data In-vitro investigations with Systemp.link Clinical assessment Biocompatibility...
Scientific Documentation Systemp.link Page 2 of 9 Table of Contents 1. Introduction...3 1.1 Temporary restorations... 3 1.2. Temporary luting materials... 3 1.3. Systemp.link... 3 2. Technical data...4
More informationDPI Luting Cement. DPI Restorative Cement
DPI Luting Cement DPI Luting Cement is Type I glass ionomer white luting cement. DPI glass ionomers are remarkably biocompatible and can be safely used in deep cavities provided the pulp is not exposed,
More informationNextDent, the leading manufacturer of dental materials for 3D printing
NextDent, the leading manufacturer of dental materials for 3D printing Biocompatible 3D printing materials Company NextDent B.V. was founded in 2012 in The Netherlands as an independent subsidiary company
More informationGeneral Properties of Dental Materials Physical properties: 1-Color Translucence
The science of dental materials involves a study of the composition and properties of materials and the way in which they interact with the environment in which they are placed. General Properties of Dental
More informationRehabilitation of Resorbed Mandibular Ridge with Implant Supported Overdenture- A Clinical Report
Rehabilitation of Resorbed Mandibular Ridge with Implant Supported Overdenture- A Clinical Report 1 2 1 1 Mittal R, Saxena D, Rao S, Kumar M Abstract: Statement of Problem: Complete denture rehabilitation
More informationFlexural Strength of Poly Propylene Fiber Reinforced PMMA
International Journal of Pharmaceutical Science Invention ISSN (Online): 2319 6718, ISSN (Print): 2319 670X Volume 6 Issue 2 February 2017 PP. 21-25 Flexural Strength of Poly Propylene Fiber Reinforced
More informationSAFETY DATA SHEET UV LAMINATION ADHESIVE
Revision Date 06/12/2012 Revision 1 SAFETY DATA SHEET SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING 1.1. Product identifier Product name Product No. 40UC91015 1.2. Relevant
More informationPulpdent Corporation Revision Date: May 6, 2014 Safety Data Sheet
1.0 Commercial Product Name and Supplier 1.1 Commercial product name / designation Ortho-Choice OBA Bonding Resin 1.2 1.2.2 1.2.3 Application / Use SIC Use Category Dental material for use by dental professional
More informationTizian Blank. Tizian Zirconia Reinforced Composite
Tizian Blank Tizian Zirconia Reinforced Composite Inspired by Nature This innovative combination of materials offers both the advantages of high-performance acrylics and zirconium dioxide: The CAD/CAM
More informationLecture:6 dental material dr. Aseel Mohammed
4. Zinc oxide eugenol impression material: It's described as a rigid, mucostatic, irreversible (set by chemical reaction) and hydrophobic impression material. We have 2 types of zinc oxide eugenol impression
More informationItem number Item number Item number
Tall Oil products product Distilled Tall Oil (DTO) Product name UCY10 UCY15 UCY20 UCY20-25 UCY25-30 UCY30-40 Item number 10-004 10-011 10-012 10-009 10-005 10-013 Page 3 4 5 6 7 8 Item number 10-006 10-007
More information!Lorem&Ipsum& Bowen!Monofilaments!for!Toothbrushes!!
LoremIpsum Bowen MonofilamentsforToothbrushes Company Profile Qidong Bowen Engineering Plastics Company Ltd started operations in 1997 in Wuxi, with polymerization of high end polyamides Nylon 6,10, Nylon
More informationDr.N.Damodharan Professor and head Department of pharmaceutics SRM college of pharmacy
Dr.N.Damodharan Professor and head Department of pharmaceutics SRM college of pharmacy Suppositories are solid dosage forms intended for insertion into body orifices where they melt, soften, or dissolve
More informationFor the Perfect Class V and All Cervical Area Gingival Margins when Placing Direct Composites, Create an Injection Molding Matrix
Cronicon OPEN ACCESS EC DENTAL SCIENCE Case Report For the Perfect Class V and All Cervical Area Gingival Margins when Placing Direct Composites, Create an Injection Molding Paul C Belvedere* Adjunct Professor,
More informationVarseoWax CAD/Cast GEBRAUCHSANWEISUNG INSTRUCTIONS FOR USE MODE D EMPLOI INSTRUCCIONES DE USO ISTRUZIONI PER L USO Partners in Progress
www.bego.com VarseoWax CAD/Cast GEBRAUCHSANWEISUNG INSTRUCTIONS FOR USE MODE D EMPLOI INSTRUCCIONES DE USO ISTRUZIONI PER L USO Partners in Progress EN INSTRUCTION FOR USE VarseoWax CAD/Cast VarseoWax
More information3D Printing Dentures. Dental Application Print Guide
Dental Application Print Guide 3D Printing Dentures Denture Base Resin is a highly accurate material specifically formulated for the creation of custom denture bases of all types. Production capabilities
More informationMATERIAL SAFETY DATA SHEETS
REVISED DEC./2014 1. CHEMICAL PRODUCT Adhesive Systems, Inc. 9411 Corsair Road Frankfort, IL 60423 1-800-552-0299 Phone 1-815-464-5650 Fax EMERGENCY PHONE 1-800-255-3924 International +01+813-248-0585
More informationTECHNICAL GUIDE KATANA ZIRCONIA MULTI-LAYERED SERIES
TECHNICAL GUIDE KATANA ZIRCONIA MULTI-LAYERED SERIES HIGH ESTHETIC WITH KATANA ZIRCONIA* New series which features translucency similar to natural tooth enamel is now available. Introducing the new series
More informationInternational J. of Healthcare and Biomedical Research, Volume: 04, Issue: 01, October 2015, Pages 17-25
Original article: A Comparative evaluation of shear bond strengths of denture base to cross linked acrylic resin maxillary anterior teeth with and without retentive grooves - An invitro study Dr.D.Sudha
More informationSafety Data Sheet. SECTION 1: Identification of the substance/mixture and of the company/undertaking
Product code: 110368, 110400-110404, 110406 (1300_GHS) Page 1 of 5 SECTION 1: Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier 1.2. Relevant identified uses
More informationPOLYTONE UA 810. Aldehyde Resin
An Aldehyde Resin which is yellowing resistant, practically soluble in almost all paint solvents and compatible with almost all coating raw material. Aldehyde Resin POLYOLS & POLYMERS PVT.LTD. C-1/58-59,
More informationSafety Data Sheet according to (EC) No 1907/ ISO
Safety Data Sheet according to (EC) No 1907/2006 - ISO 11014-1 Page 1 of 7 Loctite V5004 Part B sds no. : 328930 Revision: 11.06.2010 printing date: 03.01.2012 1. Identification of the substance/preparation
More informationISO INTERNATIONAL STANDARD. Dentistry Casting and baseplate waxes. Art dentaire Cires pour coulée et pour plaque de base
INTERNATIONAL STANDARD ISO 15854 First edition 2005-07-15 Dentistry Casting and baseplate waxes Art dentaire Cires pour coulée et pour plaque de base Reference number ISO 15854:2005(E) ISO 2005 PDF disclaimer
More informationCoating powders are mixtures of pigments, resins, curing. As the coating powder is sprayed through the nozzle of the
CONTROLLING EXPOSURE TO COATING POWDERS INTRODUCTION What are coating powders? Coating powders are mixtures of pigments, resins, curing agents and other additives. They give a durable finish and are used
More informationProduct Information. Meliodent The solution for every denture Effective material from a proven partner. Giving a hand to oral health.
Product Information Meliodent The solution for every denture Effective material from a proven partner Giving a hand to oral health. Meliodent products from Kulzer. A range of impressive cost effective
More informationSAFETY DATA SHEET SECTION 1 - IDENTIFICATION
SAFETY DATA SHEET SECTION 1 - IDENTIFICATION Product Identifier: RP-OCNF LIFT STATION DEGREASER Recommended Use: RED SOLVENT LIFT STATION DEGREASER Restrictions on Use: INDUSTRIAL OR PROFESSIONAL USE ONLY
More informationOperative dentistry. Lec: 10. Zinc oxide eugenol (ZOE):
Operative dentistry Lec: 10 د.عبذالمنعم الخفاجي Zinc oxide eugenol (ZOE): There are 2 types: 1) Unreinforced ZOE (ordinary type): supplied as powder (zinc oxide + some additives like zinc acetate, white
More informationACCREDITATION STANDARDS FOR DENTAL LABORATORY TECHNOLOGY EDUCATION PROGRAMS Frequency of Citings Based on Required Areas of Compliance
Page 1 ACCREDITATION STANDARDS FOR DENTAL LABORATORY TECHNOLOGY EDUCATION PROGRAMS Based on Required Areas of Compliance Total Number of Programs Evaluated: 13 July 2009 through December 2013 STANDARD
More informationSAFETY DATA SHEET SECTION 1 - IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE COMPANY / UNDERTAKING
Safety Data Sheet (in compliance with Regulation (EC) 1907/2006, Regulation (EC) 1272/2008 and Regulation (EC) 453/2010 Document Number: 728-00001 Current Revision: - Issue Date: 8/22/2017 SECTION 1 -
More informationGingiva Solution SR Phonares II, IvoBase, SR Nexco
Gingiva Solution SR Phonares II, IvoBase, SR Nexco Preface 5 Framework design 6 Framework preparation 8 Finishing of the denture base 10 Gingival modification 12 Mobile mucosa 14 Immobile mucosa 16 Lip
More informationMATERIAL SAFETY DATA SHEET
In case of spillage: Absorb with inert material. Collect in closed containers and dispose in accordance with Federal, State and local regulations. Avoid skin contact, wear protective equipment. Waste Disposal:
More information