Tri-Rez Polyol Polyester Resin Product Data

Size: px
Start display at page:

Download "Tri-Rez Polyol Polyester Resin Product Data"

Transcription

1 Tri-Rez Polyol Polyester Resin Product Data TRI-REZ POLYOL TECHNICAL DATA SHEET Tri-Rez Polyol is a highly crystalline saturated linear polyester polyol designed for use in polyurethane based coatings and adhesives. GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: TRIMET@geosc.com GEO Specialty Chemicals, Ltd. Customer Service (Europe) Suite 4, Fairview Court Fairview Road Cheltenham, Glos. GL52 2EX UK Tel: Fax: TRIMET-EU@geosc.com The hydrophobic crystalline structure of Tri-Rez Polyol makes it an ideal polyol for formulating high solids and water-borne polyurethane resins for heat activated laminating adhesives. Technical Data 25 C Acid value (as supplied), mg KOH/g Typical Properties Solid opaque resin 0.8 max Hydroxyl number (as supplied), mg KOH/g Non-volatile % Brookfield 60 C (as supplied) Colour, APHA Density Pounds / 25 C Grams / 25 C 98 min poise 250 max 8.9 +/ /- 40 Website: Moisture, % 0.05 max

2 Tri-Rez Polyol Technical Datasheet Handling & Storage Tri-Rez Polyol is a hygroscopic material; contamination from atmospheric moisture will cause undesirable side reactions in urethane formulations. Container should be sealed at all times unless discharging. If pre-heating is required, a maximum temperature of 70 C is recommended. Tri-Rez Polyol can be stored for up to 30 days at 70 C with no adverse reactions. The shelf-life of the material is 12 months after receipt if stored in the original container at 0-50 C All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Created: February 2011

3 Tri-Rez Polyol Polyester Resin Product Data TRI-REZ POLYOL TECHNICAL DATA SHEET GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Suite 4, Fairview Court Fairview Road Cheltenham, Glos. GL52 2EX UK Tel: Fax: Tri-Rez Polyol is a non-crystalline low viscosity saturated linear polyester polyol designed for polyurethane based coatings, adhesives and foams. The hydrophobic flexible structure of Tri-Rez Polyol makes it an ideal polyol for formulating high solids and water-borne polyurethane resins. Technical Data Appearance Acid value (as supplied), mg KOH/g Typical Properties Clear viscous liquid 0.8 max Hydroxyl number (as supplied), mg KOH/g Non-volatile % Brookfield 25 C (as supplied) Colour, APHA Density Pounds / 25 C Grams / 25 C 98 min poise 250 max 9.1 +/ /- 40 Website: Moisture, % 0.05 max

4 Tri-Rez Polyol Technical Datasheet Handling & Storage Tri-Rez Polyol is a hygroscopic material; contamination from atmospheric moisture will cause undesirable side reactions in urethane formulations. Container should be sealed at all times unless discharging. If pre-heating is required, a maximum temperature of 70 C is recommended. Tri-Rez Polyol can be stored for up to 30 days at 70 C with no adverse reactions. The shelf-life of the material is 12 months after receipt if stored in the original container at 0-50 C All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Created: February 2011

5 Tri-Rez Polyol Polyester Resin Product Data TRI-REZ POLYOL TECHNICAL DATA SHEET GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Suite 4, Fairview Court Fairview Road Cheltenham, Glos. GL52 2EX UK Tel: Fax: Tri-Rez Polyol is a non-crystalline low viscosity saturated linear polyester polyol designed for polyurethane based coatings, adhesives and foams. The hydrophobic flexible structure of Tri-Rez Polyol makes it an ideal polyol for formulating high solids and water-borne polyurethane resins. Technical Data Appearance Acid value (as supplied), mg KOH/g Typical Properties Clear viscous liquid 0.8 max Hydroxyl number (as supplied), mg KOH/g Non-volatile % Brookfield 25 C (as supplied) Colour, APHA Density Pounds / 25 C Grams / 25 C 98 min poise 250 max 9.1 +/ /- 40 Website: Moisture, % 0.05 max

6 Tri-Rez Polyol Technical Datasheet Handling & Storage Tri-Rez Polyol is a hygroscopic material; contamination from atmospheric moisture will cause undesirable side reactions in urethane formulations. Container should be sealed at all times unless discharging. If pre-heating is required, a maximum temperature of 70 C is recommended. Tri-Rez Polyol can be stored for up to 30 days at 70 C with no adverse reactions. The shelf-life of the material is 12 months after receipt if stored in the original container at 0-50 C All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Created: February 2011

7 Tri-Rez Polyol Polyester Resin Product Data TRI-REZ POLYOL TECHNICAL DATA SHEET GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Suite 4, Fairview Court Fairview Road Cheltenham, Glos. GL52 2EX UK Tel: Fax: Tri-Rez Polyol is a non-crystalline low viscosity saturated linear polyester polyol designed for polyurethane based coatings, adhesives and foams. The hydrophobic flexible structure of Tri-Rez Polyol makes it an ideal polyol for formulating high solids and water-borne polyurethane resins. Technical Data Appearance Acid value (as supplied), mg KOH/g Typical Properties Clear viscous liquid 0.8 max Hydroxyl number (as supplied), mg KOH/g Non-volatile % Brookfield 25 C (as supplied) Colour, APHA Density Pounds / 25 C Grams / 25 C 98 min poise 250 max 9.0 +/ /- 40 Website: Moisture, % 0.05 max

8 Tri-Rez Polyol Technical Datasheet Handling & Storage Tri-Rez Polyol is a hygroscopic material; contamination from atmospheric moisture will cause undesirable side reactions in urethane formulations. Container should be sealed at all times unless discharging. If pre-heating is required, a maximum temperature of 70 C is recommended. Tri-Rez Polyol can be stored for up to 30 days at 70 C with no adverse reactions. The shelf-life of the material is 12 months after receipt if stored in the original container at 0-50 C All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Created: February 2011

9 Tri-Rez Polyol Polyester Resin Product Data TRI-REZ POLYOL TECHNICAL DATA SHEET Tri-Rez is a semi-crystalline saturated linear polyester polyol designed for polyurethane based coatings, adhesives and foams. GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: TRIMET@geosc.com GEO Specialty Chemicals, Ltd. Customer Service (Europe) Suite 4, Fairview Court Fairview Road Cheltenham, Glos. GL52 2EX UK Tel: Fax: TRIMET-EU@geosc.com The hydrophobic flexible structure of Tri-Rez Polyol makes it an ideal polyol for formulating high solids and water-borne polyurethane resins. Technical Data Appearance Acid value (as supplied), mg KOH/g Typical Properties Clear viscous liquid 0.8 max Hydroxyl number (as supplied), mg KOH/g Non-volatile % Brookfield 60 C (as supplied) Colour, APHA Density Pounds / 25 C Grams / 25 C 98 min poise 250 max 9.0 +/ /- 40 Website: Moisture, % 0.05 max

10 Tri-Rez Polyol Technical Datasheet Handling & Storage Tri-Rez Polyol is a hygroscopic material; contamination from atmospheric moisture will cause undesirable side reactions in urethane formulations. Container should be sealed at all times unless discharging. If pre-heating is required, a maximum temperature of 70 C is recommended. Tri-Rez Polyol can be stored for up to 30 days at 70 C with no adverse reactions. The shelf-life of the material is 12 months after receipt if stored in the original container at 0-50 C All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Created: February 2011

11 Tri-Rez Polyol Polyester Resin Product Data TRI-REZ POLYOL TECHNICAL DATA SHEET GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Suite 4, Fairview Court Fairview Road Cheltenham, Glos. GL52 2EX UK Tel: Fax: Tri-Rez Polyol is a semi-crystalline saturated linear polyester polyol designed for polyurethane based coatings, adhesives and foams. The hydrophobic flexible structure of Tri-Rez Polyol makes it an ideal polyol for formulating high solids and water-borne polyurethane resins. Technical Data Appearance Acid value (as supplied), mg KOH/g Typical Properties Clear viscous liquid 0.8 max Hydroxyl number (as supplied), mg KOH/g Non-volatile % Brookfield 40 C (as supplied) Colour, APHA Density Pounds / 25 C Grams / 25 C 98 min poise 250 max 9.3 +/ /- 40 Website: Moisture, % 0.05 max

12 Tri-Rez Polyol Technical Datasheet Handling & Storage Tri-Rez Polyol is a hygroscopic material; contamination from atmospheric moisture will cause undesirable side reactions in urethane formulations. Container should be sealed at all times unless discharging. If pre-heating is required, a maximum temperature of 70 C is recommended. Tri-Rez Polyol can be stored for up to 30 days at 70 C with no adverse reactions. The shelf-life of the material is 12 months after receipt if stored in the original container at 0-50 C All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Created: February 2011

13 Tri-Rez Polyol Polyester Resin Product Data TRI-REZ POLYOL TECHNICAL DATA SHEET GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Suite 4, Fairview Court Fairview Road Cheltenham, Glos. GL52 2EX UK Tel: Fax: Tri-Rez Polyol is a non-crystalline saturated linear polyester polyol designed for polyurethane based coatings, adhesives and foams. The hydrophobic flexible structure of Tri-Rez Polyol makes it an ideal polyol for formulating high solids and water-borne polyurethane resins. Technical Data Appearance Acid value (as supplied), mg KOH/g Typical Properties Clear viscous liquid 0.8 max Hydroxyl number (as supplied), mg KOH/g Non-volatile % Brookfield 25 C (as supplied) Colour, APHA Density Pounds / 25 C Grams / 25 C 98 min poise 250 max 9.3 +/ /- 40 Website: Moisture, % 0.05 max

14 Tri-Rez Polyol Technical Datasheet Handling & Storage Tri-Rez Polyol is a hygroscopic material; contamination from atmospheric moisture will cause undesirable side reactions in urethane formulations. Container should be sealed at all times unless discharging. If pre-heating is required, a maximum temperature of 70 C is recommended. Tri-Rez Polyol can be stored for up to 30 days at 70 C with no adverse reactions. The shelf-life of the material is 12 months after receipt if stored in the original container at 0-50 C All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Created: February 2011

15 Tri-Rez Polyol Polyester Resin Product Data TRI-REZ POLYOL TECHNICAL DATA SHEET GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Suite 4, Fairview Court Fairview Road Cheltenham, Glos. GL52 2EX UK Tel: Fax: Tri-Rez Polyol is a non-crystalline saturated linear polyester polyol designed for polyurethane based coatings, adhesives and foams. The hydrophobic flexible structure of Tri-Rez Polyol makes it an ideal polyol for formulating high solids and water-borne polyurethane resins. Technical Data Appearance Acid value (as supplied), mg KOH/g Typical Properties Clear viscous liquid 0.8 max Hydroxyl number (as supplied), mg KOH/g Non-volatile % Brookfield 25 C (as supplied) Colour, APHA Density Pounds / 25 C Grams / 25 C 98 min poise 250 max 9.3 +/ /- 40 Website: Moisture, % 0.05 max

16 Tri-Rez Polyol Technical Datasheet Handling & Storage Tri-Rez Polyol is a hygroscopic material; contamination from atmospheric moisture will cause undesirable side reactions in urethane formulations. Container should be sealed at all times unless discharging. If pre-heating is required, a maximum temperature of 70 C is recommended. Tri-Rez Polyol can be stored for up to 30 days at 70 C with no adverse reactions. The shelf-life of the material is 12 months after receipt if stored in the original container at 0-50 C All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Created: February 2011

17 Tri-Rez Polyol Polyester Resin Product Data TRI-REZ POLYOL TECHNICAL DATA SHEET GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Suite 4, Fairview Court Fairview Road Cheltenham, Glos. GL52 2EX UK Tel: Fax: Tri-Rez Polyol is a non-crystalline low viscosity saturated linear polyester polyol designed for polyurethane based coatings, adhesives and foams. The hydrophobic flexible structure of Tri-Rez Polyol makes it an ideal polyol for formulating high solids and water-borne polyurethane resins. Technical Data Appearance Acid value (as supplied), mg KOH/g Typical Properties Clear viscous liquid 0.8 max Hydroxyl number (as supplied), mg KOH/g Non-volatile % Brookfield 25 C (as supplied) Colour, APHA Density Pounds / 25 C Grams / 25 C 98 min poise 250 max 9.3 +/ /- 40 Website: Moisture, % 0.05 max

18 Tri-Rez Polyol Technical Datasheet Handling & Storage Tri-Rez Polyol is a hygroscopic material; contamination from atmospheric moisture will cause undesirable side reactions in urethane formulations. Container should be sealed at all times unless discharging. If pre-heating is required, a maximum temperature of 70 C is recommended. Tri-Rez Polyol can be stored for up to 30 days at 70 C with no adverse reactions. The shelf-life of the material is 12 months after receipt if stored in the original container at 0-50 C All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Created: February 2011

19 DICAP 2020 Acid Functional Saturated Polyester Polyol Product Data DICAP 2020 TECHNICAL DATA SHEET DICAP 2020 is a linear saturated polyester diol with a pendant carboxylic functional group. GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: TRIMET@geosc.com The OH terminated polyester chains are DMPA Dimethylolpropionic acid initiated polycaprolactone. The combination of both hydroxyl and carboxyl functionalities produces unique benefits and versatility. The acid group promotes water dispersability of the resin after neutralisation with a base or can improve adhesion to difficult substrates. Technical Data Typical Properties Appearance Waxy solid GEO Specialty Chemicals, Ltd. Customer Service (Europe) Unit C, Pate Court, North Place Cheltenham, Glos. GL50 4DY UK Tel: Fax: TRIMET-EU@geosc.com Website: Melting point (DSC), C 58.3 Non-volatile content, wt. % 99 min Hydroxyl number, mgkoh / g Acid number, mgkoh / g Hydroxyl equivalent weight, g / eqv. (as supplied) Acid equivalent weight, g / eqv Water content wt., % < 0.2 Colour, Gardner 2 max 60 C, cp

20 DICAP Technical Datasheet O CH 3 O H[O(CH 2 ) 5 C] m O-C-C-C-O-[C(CH 2 ) 5 O] n H COOH CAS Registry No Exempt Under EINECS Polymer Exemption Applications DICAP 2020 can be used in combination with polyester, polyether, acrylic or polycarbonate polyols to formulate pre-polymers for polyurethane dispersions without DMPA. Since no DMPA is required to formulate water dispersible pre-polymers, NMP may be reduced or eliminated from the formulations. Pre-polymers formulated with DICAP products have very good solubility in monomers for hybrid applications and in acetone for solvent-free PUDs. Depending on the molecular weight of the DICAP polyol and the formulating technique, hard films can be formulated for durable coatings or soft urethane polymers can be formulated for coating textiles and leathers. Solubility DICAP products can be used in compliance with 21CFR for indirect contact with food. DICAP 2020 is soluble in aromatic hydrocarbons, esters, ether esters, ketones and TBAC. It is insoluble in aliphatic hydrocarbon solvents. Most solutions will stay liquid at 25 C at 50% solids. Higher concentrations require gentle heating to remain liquid. Packaging DICAP products are available in 200kg open head lined steel drums. Shipping, Storage & Handling DICAP 2020 is supplied as a waxy solid that can be easily melted with steam or in a hotbox for easy handling. DICAP products should be melted at C 48 to 72 hours before use. It is not recommended to leave DICAP products at elevated temperature for extended periods of time. Not DOT regulated. Store products in airtight containers in a cool, dry ventilated area. NPFA rating: Health: 1, Flammability: 1, Reactivity: 0. Please refer to the product MSDS for more information. All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Revised: May 2010

21 DMPA Dimethylolpropionic Acid DMPA Brand of Dimethylolpropionic Acid PRODUCT TECHNICAL GUIDE GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Unit C, Pate Court, North Place Cheltenham, Glos. GL50 4DY UK Tel: Fax: Website: DMPA Dimethylolpropionic Acid, C 5 H 10 O 4 CH 2 OH CH 3 C COOH CH 2 OH CAS Registry No EINECS Registry No

22 DMPA Brand of Dimethylolpropionic Acid - Product Technical Guide Introduction DMPA Brand of Dimethylolpropionic Acid is a unique and versatile hindered diol molecule with both hydroxyl and carboxyl functionality. The neopentyl structure of this trifunctional compound, having two primary hydroxyl groups and one tertiary carboxylic group, permits simplified processing by allowing the combining of all reactants in a single kettle charge. Good control of the reaction is possible due to the slower esterification rate of the tertiary carboxyl, assuring a uniform distribution of carboxyl groups along the resin backbone. The free acid group actively promotes resin water solubility or water dispersability after neutralization with a base, easily introduces a polar group to improve coating adhesion and synthetic fibre dye receptivity, and increases the alkali solubility of deposited films. DMPA is an odourless, free flowing white crystalline solid which provides superior advantages in the formulation and processing of water soluble resins. Specifications Hydroxyl Content, wt % Neutralization Equivalent, g / eq min max Ash as Na 2 O, wt % 0.03 max Moisture, wt % 0.3 max Water Insolubles, ppm 50.0 max Colour, APHA 250 max Typical Properties Molecular Weight Acid Number, mg KOH / g Melting Point, C Flashpoint (Cleveland Open Cup), C 220 Decomposition Temperature, C 230 Bulk Density, lbs / ft Solubility, g / 100g 25 C Water 11 Acetone 2.3 Ethanol insoluble Uses DMPA is widely used in: Aqueous urethane dispersions, resulting in fast air-drying, high gloss waterborne coatings with superior toughness and flexibility. Water soluble alkyd and polyester resins for improved hydrolytic stability, minimal coupling solvent and improved early water spot resistance in air dried resins. Powder coatings as a modifier for improved gloss, impact resistance and flow properties in epoxy-polyester systems. In polyester blocked isocyanate systems, DMPA imparts a high melting point hydroxyl functional reactive diluent for improved coating flexibility. 2

23 DMPA Brand of Dimethylolpropionic Acid - Product Technical Guide Epoxy ester coatings to permit resin formulating flexibility for improved cure response or larger oil strengths, to make resins water soluble, and for electrodeposition resins. Urethane elastomers as a modifier for improved adhesion to plastics, glass and steel. Electrodeposition coatings as a high performance neutralizing acid for cathodic electro deposition and as a source of free acid groups in formulating anodic electrodeposition resins. Nylon / polyester fibre blends for improved compatibility and tear resistance. Lubricating oil additives as a carrier for thiophosphates or in rust inhibiting derivatives. Photo resists / photo print plates as a modifier of phenolic and urethane resists for improved alkali solubility and improved resolution in aqueous development systems. Additional data on uses of DMPA and patent references may be found in A Complete Guide to the DMPA Brand of Dimethylolpropionic Acid which can be obtained from your GEO Specialty Chemicals, Paints & Coatings Group customer service representative. Toxicity DMPA is essentially non-toxic. Tests with white mice indicate an LD 50 for oral ingestion of greater than 5000mg / kg. No data is available on inhalation of DMPA dust; no problems have been reported. DMPA is not irritating to intact skin but may be slightly irritating to abraded skin. It is moderately irritating to the eyes with the irritation limited to the conjunctival area. First aid: for skin contact, wash thoroughly with mild soap and water; for eyes, flush with water for at least fifteen minutes. See an ophthalmologist if irritation persists. Contaminated clothing should be laundered before re-use. Refer to the product MSDS for all safety and first aid information. Shipping, Handling and Storage DMPA is packaged in 250lb fibre drums, 50lb and 25kg multi-wall paper bags with HDPE liners and 500kg super sacks with LDPE liners. DMPA is classified as DOT not regulated by the US Department of Transportation and requires no special labelling for shipment. The Harmonized Tariff Code is DMPA should be stored in a clean, dry area, following good warehousing practices. The NFPA Hazardous Materials Identification System rating for DMPA is: Health Hazard - 0; Flammability: - 1; Reactivity: - 0. This rating indicates that DMPA is a minimal hazard substance. Dimethylolpropionic acid is listed on the Chemical Substance Inventory under the US Toxic Substances Control Act, on the Canadian DSL and in the European Inventory of Existing Chemical Substances. The US and Canadian CAS Registry Number is and the European EINECS Registry Number is The REACH pre-registration number for GEO Specialty Chemical s DMPA Dimethylolpropionic acid is All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 3 Revised: October 2009

24 DMPA Dimethylolpropionic Acid Hydrolytic Stability vs. Trimellitic Anhydride (TMA) DMPA Brand of Dimethylolpropionic Acid TECHNICAL BULLETIN #7 GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Unit C, Pate Court, North Place Cheltenham, Glos. GL50 4DY UK Tel: Fax: Website:

25 DMPA Brand of Dimethylolpropionic Acid - Technical Bulletin # 7 Introduction This bulletin summarizes the processing and evaluation of DMPA Brand of Dimethylolpropionic Acid versus Trimellitic Anhydride (TMA) in isophthalic acid polyesters for water borne baking enamels. Table 1 - Polyester Starting Point Formulation Polyester Formulations EX EX Supplier Raw materials Dipropylene glycol Aldrich Trimethylolethane GEO Isophthalic acid Flint Hills DMPA 55 0 GEO TMA Flint Hills Total parts Water Loss Yield Procedure: Equipment: Round bottom four neck flask J-Kem temperature controller Nitrogen sparge tube Overhead mechanical stirrer Vigoreaux column Reflux condenser Water trap 1. Charge dipropylene glycol and TME to a reactor set up for fusion processing. 2. Heat glycol solution to C with low nitrogen sparge and moderate agitation. 3. At C, charge isophthalic acid and set the temperature to C. 4. At 205 C, hold for 2 hours, then continue heating to 230 C at a rate of 5-10 C per hour with low nitrogen sparge. 5. Hold at 230 C until one half of the theoretical water is collected, then cool to 190 C and charge DMPA. 6. Reheat to C and hold for acid value of Cool batch and discharge to container 2

26 Table 2 - Typical Resin Properties DMPA Brand of Dimethylolpropionic Acid - Technical Bulletin # 7 Properties Non Volatile content, % (Method 24) Results 98 min Acid Value on solids, mgkoh /g Hydroxyl Number, mgkoh /g Viscosity, Gardner - 70% in butyl cellosolve Colour, 70% in butyl cellosolve X - Z 2-4 Table 3 - Solvent Free Water Borne Baking Enamel Formulation Raw Materials Parts Polyester polyol 238 Cymel 303 * 102 Dimethylethanol amine (DMEA) 14.3 De-ionized water Total parts 1000 * Cytec Industries Procedure: 1. Warm polyester and Cymel 303 to C then charge to vessel and begin mixing at moderate shear. 2. When resin blend is homogeneous, charge the DMEA and continue to mix at moderate shear. 3. Warm de-ionized water to C. 4. Increase the shear and begin charging the de-ionized water at an even rate. 5. When the viscosity has decreased to the minimum, reduce the shear and adjust ph and viscosity as needed. 3

27 Table 4 - Typical Coating Properties DMPA Brand of Dimethylolpropionic Acid - Technical Bulletin # 7 Properties Results Non-Volatile content, % Viscosity, cp ph Table 5 - Stability 120 F Time 0 week 1 week 2 weeks 3 weeks DMPA Polyester ph Visual clear clear clear slight haze * TMA Control ** ph Visual opaque separated - - * ph adjusted to 7.5 with DMEA and solution cleared ** TMA control was prepared using standard TMA polyester processing Conclusion It can be concluded that DMPA gives greater hydrolytic stability All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 4 Created: March 2010

28 DMPA Polyol HA-0135 Product Data DMPA Polyol HA-0135 TECHNICAL DATA SHEET DMPA Polyol HA-0135 is a linear polyester polyol that contains both hydroxyl and acid functionality. GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: TRIMET@geosc.com GEO Specialty Chemicals, Ltd. Customer Service (Europe) Unit C, Pate Court, North Place Cheltenham, Glos. GL50 4DY UK Tel: Fax: TRIMET-EU@geosc.com The structure of DMPA Polyol HA-0135 has been specifically designed to achieve maximum hydrolytic stability in water-borne applications. DMPA Polyol HA-0135 can be used to formulate high solids and NMP free polyurethane dispersions. Technical Data Appearance Properties Clear / lightly hazy viscous liquid Acid Value, mgkoh / g (as supplied) Hydroxyl Number, mgkoh / g (as supplied) Non-volatile, % Brookfield 100% NV C C C P 25 C, grams / litre Website: Colour, APHA Moisture, % 450 max 0.5 max

29 DMPA Polyol HA Technical Datasheet Applications Source of acid functionality for water-borne applications. Co-resin to improve pigment wetting, dispersing and stabilising. Pendant acid group can be used to improve adhesion in baking enamels and 2K urethanes. Acid groups can react with epoxy functional monomers to add acrylate functionality for UV / EB applications. Hydroxyl groups can be reacted with isocyanate functional acrylates to produce UV / EB cured water-borne coatings. Storage DMPA Polyol HA-0135 is very hygroscopic. Container should be sealed at all times unless discharging. Due to the reactive nature of the material, containers should be tightly sealed and stored at 0-30 C. If preheating is required for discharging, DMPA Polyol HA-0135 should be heated to a maximum temperature of 70 C for no longer than 48 hours. If the material is exposed to >70 C for extended periods of time, undesirable side reactions could occur that could cause variations in the properties of the prepared formulations. The shelf life of the material is twelve months after receipt of the material if stored in a sealed container at 0-30 C. All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Revised: May 2010

30 DMPA Polyol HA-0135 Low VOC PUDs for Heat Activated Laminated Adhesives DMPA Polyol HA-0135 TECHNICAL BULLETIN #6 GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Unit C, Pate Court, North Place Cheltenham, Glos. GL50 4DY UK Tel: Fax: DMPA Polyol HA-0135 is a low molecular weight linear polyester polyol that contains primary hydroxyl and tertiary carboxyl groups in the terminal positions. The fact that the DMPA is built into a polymeric polyol eliminates the crystalline properties associated with pure DMPA and as a result, formulating low VOC PUDs with a solvent-free process is much easier. At 25 C, DMPA Polyol HA-0135 is a viscous liquid; however, when mild heat is applied, the viscosity of the resin decreases rapidly. DMPA Polyol HA-0135 has a unique structure that provides excellent hydrolytic stability in PUD formulations. To illustrate the benefits and properties of DMPA Polyol HA-0135 in PUD formulations, a low VOC PUD formulation utilizing a solvent-free process is provided. Website:

31 DMPA Polyol HA Technical Bulletin #6 DMPA Polyol HA-0135 visc cps temp C Part I - Synthesis of the NCO terminated pre-polymer (parts by weight) Pre-Polymer Formulation EXP EXP Diexter-G * DMPA Polyol HA Desmodur I ** TMXDI **** Acclaim Polyol N2220 ** Dipropyleneglycol DME *** Total parts EXP * Coim USA Inc. *** Clariant Corporation ** Bayer MaterialScience LLC **** Cytec Industries 1. Charge Diexter G and DMPA Polyol HA-0135 to a reactor equipped with agitator, inert gas sparging tube, a temperature controller and a water-cooled condenser. 2. Heat the contents to 80 C and hold until the solution is homogeneous. Add isocyanate (Desmodur I or TMXDI ), then reheat the batch to 80 C and hold for 1 hour. After one hour, charge N2220 and solvent (DPG-DME) if needed, heat to 90 C and hold for the NCO end point. Note: % NCO is determined by the di-n-butylamine titration method. 3. When the anticipated percent NCO is obtained, prepare for "Neutralization", Dispersion and Chain Extension". 4. Determine and record the final properties of the pre-polymer solution, such as % non-volatile, viscosity, and % NCO. 2

32 DMPA Polyol HA Technical Bulletin #6 Pre-Polymer Properties EXP EXP Non-Volatile, % EXP C, Brookfield #5 20 rpm, cp NCO : OH Free NCO, % Acid Value on solids, mgkoh / g Part II - Neutralization, Dispersion & Chain Extension (parts by weight) Dispersion Formulation EXP EXP Pre-Polymer Triethylamine (TEA) Di-ionized Water * Ethylene Diamine De-ionized Water Total parts EXP * Note: for lab reactions the pre-polymer was charged to the dispersing vessel and neutralized before adding first charge of water. The water was heated to C prior to charging. For production, TEA and water are first charged to the dispersing vessel followed by the pre-polymer. Dispersion Procedure Neutralization and dispersing pre-polymer: 1. At 75 C, begin transferring pre-polymer solution to dispersing vessel equipped with high-speed dispersing agitator. Begin agitation on low to medium speed and charge triethylamine (TEA). Allow time for TEA to mix in, typically 3-5 minutes for a 1000g lab batch. 2. Increase agitator speed to rpm and begin charging de-ionized water at a rate sufficient to maintain a vortex. Once water is in and the resin is dispersed, reduce agitator speed and rapidly cool to C. 3

33 DMPA Polyol HA Technical Bulletin #6 Chain Extension: 3. While dispersion is cooling, pre-mix ethylene diamine (EDA) and second charge of water. 4. Once the dispersion is below 30 C, begin agitation of EDA and water. Note: it is best to start addition slowly then gradually increase rate if viscosity is stable. If viscosity increases, stop addition until viscosity reduces. If viscosity does not reduce after 1-2 minutes, add more de-ionized water in small increments until it does. Repeat process if viscosity continues to increase during chain extension. 5. Once all the EDA water pre-mix is in, reduce agitator speed to rpm and continue mixing for approx. 20 minutes. Dispersion Properties EXP EXP Non-volatile, % EXP C, Brookfield #2 20 rpm, cp KU-2 Viscometer Kreb units cp ph Density lbs/gallon, grams/litre 8.76 / / 1050 VOC (as supplied), g / l / Minimum activation temperature, C

34 DMPA Polyol HA Technical Bulletin #6 Commercial Process for PUD Synthesis OCN Isocyanate NCO OH HA 0135 OH HO Polyester OH HO Polycarbonate OH HO Polyether OH Chain Extending Diols Note: for commercial scale isocyanates are metered in to control exotherm. For lab scale isocyanate can be added all at once after polyols are homogeneous Pre polymer reactor: Nitrogen sparge, agitator, Temperature controller, condenser. NCO Terminated Pre polymer OCN Isocyanate NCO OCN Isocyanate NCO OCN Isocyanate NCO OCN Isocyanate NCO HO Polyester OH OH HA 0135 OH HO Polyester OH Note: for lab batches charge pre polymer, neutralize with TEA then add water Dispersing vessel with high speed mixer and dispersing blade Water and TEA already in reactor Increase agitator speed and begin charging pre polymer Once pre polymer is in and all resin is dispersed, begin addition of EDA/water pre mix Finished Polyurethane Dispersion (PUD) Ready for ph adjustment and filtration All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 5 Created: May 2010

35 DMPA Polyol HA-0135 Solvent-Free PUD Process For Soft-Feel Coatings DMPA Polyol HA-0135 TECHNICAL BULLETIN #7 GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Unit C, Pate Court, North Place Cheltenham, Glos. GL50 4DY UK Tel: Fax: DMPA Polyol HA-0135 is a low molecular weight linear polyester polyol that contains primary hydroxyl and tertiary carboxyl groups in the terminal positions. The fact that the DMPA is built into a polymeric polyol eliminates the crystalline properties associated with pure DMPA and as a result, formulating low VOC PUDs with a solvent-free process is much easier. At 25 C, DMPA Polyol HA-0135 is a viscous liquid; however, when mild heat is applied, the viscosity of the resin decreases rapidly. DMPA Polyol HA-0135 has a unique structure that provides excellent hydrolytic stability in PUD formulations. To illustrate the benefits and properties of DMPA Polyol HA-0135 in PUD formulations, a low VOC PUD formulation utilizing a solvent-free process is provided. Website:

36 DMPA Polyol HA Technical Bulletin #7 DMPA Polyol HA-0135 visc cps temp C Part I - Synthesis of the NCO terminated pre-polymer Pre-Polymer Formulation EXP EXP Terathane 650 * DMPA Polyol HA TMXDI ** Desmodur I *** Total * DuPont ** Cytec Industries *** Bayer MaterialScience LLC 1. Charge Terathane 650 and DMPA Polyol HA-0135 to a reactor equipped with agitator, inert gas sparging tube, a temperature controller and a water-cooled condenser. 2. Heat the contents to 80 C and hold until the solution is homogeneous. Add isocyanate (Desmodur I or TMXDI ), then reheat the batch to 80 C and hold for 1 hour. After one hour, increase the temperature to 90ºC and hold for the NCO end point. Note: % NCO is determined by the di-n-butylamine titration method. 3. When the anticipated percent NCO is obtained, prepare for "Neutralization", Dispersion and Chain Extension". 4. Determine and record the final properties of the pre-polymer solution, such as % non-volatile, viscosity, and % NCO. 2

37 DMPA Polyol HA Technical Bulletin #7 Pre-Polymer Properties EXP EXP Non-Volatile, % C, Brookfield #5 20 rpm, cp NCO : Hydroxyl Free NCO, % Acid Value, mgkoh / g Part II - Neutralization, Dispersion & Chain Extension (parts by weight) Dispersion Formulation EXP EXP Pre-Polymer Triethylamine (TEA) De-ionized Water * Ethylene Diamine De-ionized Water Total parts * Note: for lab reactions the pre-polymer was charged to the dispersing vessel and neutralized before adding first charge of water. The water was heated to C prior to charging. For production, TEA and water are first charged to the dispersing vessel followed by the pre-polymer. Neutralization and Dispersion Procedure: 1. At 75 C, begin transferring pre-polymer solution to dispersing vessel equipped with high-speed dispersing agitator. Begin agitation on low to medium speed and charge triethylamine (TEA). Allow time for TEA to mix in, typically 3-5 minutes for a 1000g lab batch. 2. Increase agitator speed to rpm and begin charging de-ionized water at a rate sufficient to maintain a vortex. Once water is in and the resin is dispersed, reduce agitator speed and rapidly cool to C. 3

38 DMPA Polyol HA Technical Bulletin #7 Chain Extension: 3. While dispersion is cooling, pre-mix ethylene diamine (EDA) and second charge of water. 4. Once the dispersion is below 30 C, begin addition of EDA / water mixture. Note: it is best to start addition slowly then gradually increase rate if viscosity is stable. If viscosity increases, stop addition until viscosity decreases. If viscosity does not decrease after 1-2 minutes, add more de-ionized water in small increments until it does. Repeat process if viscosity continues to increase during chain extension. 5. Once all the EDA / water mixture is in, reduce agitator speed to rpm and continue mixing for approx. 20 minutes. 6. After 20 minutes, stop agitation and transfer dispersion to a new container and hold for one day before adjusting ph and characterizing dispersion. Note: the one day hold is to allow for entrained air to escape. Dispersion Properties EXP EXP Non-Volatile, % Viscosity, Brookfield, cp KU-2 Viscometer Kreb units cp ph Density, lbs / gallon grams / litre 8.67 / / 1040 VOC (as supplied), g / l Film Properties EXP * % CoatOSil 2287 Silane** on TW Chemical Resistance 0.00% 0.60% 0.80% 1.00 % Sunscreen DEET, insect repellent Isopropyl alcohol % Ammonium hydroxide % Hydrochloric acid % Sulfuric acid % Acetic acid * 3 mils / 70 µm wet film baked 5 90 C, 30 minute 25 C. ** Momentive Performance Materials 4

39 DMPA Polyol HA Technical Bulletin #7 Commercial Process for PUD Synthesis OCN Isocyanate NCO OH HA 0135 OH HO Polyester OH HO Polycarbonate OH HO Polyether OH Chain Extending Diols Note: for commercial scale isocyanates are metered in to control exotherm. For lab scale isocyanate can be added all at once after polyols are homogeneous Pre polymer reactor: Nitrogen sparge, agitator, Temperature controller, condenser. NCO Terminated Pre polymer OCN Isocyanate NCO OCN Isocyanate NCO OCN Isocyanate NCO OCN Isocyanate NCO HO Polyester OH OH HA 0135 OH HO Polyester OH Note: for lab batches charge pre polymer, neutralize with TEA then add water Dispersing vessel with high speed mixer and dispersing blade Water and TEA already in reactor Increase agitator speed and begin charging pre polymer Once pre polymer is in and all resin is dispersed, begin addition of EDA/water pre mix Finished Polyurethane Dispersion (PUD) Ready for ph adjustment and filtration All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 5 Created: May 2010

40 DMPA Polyol HA-0135LV2 Product Data DMPA Polyol HA-0135LV2 TECHNICAL DATA SHEET GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Unit C, Pate Court, North Place Cheltenham, Glos. GL50 4DY UK Tel: Fax: Website: DMPA Polyol HA-0135LV2 is a low crystalline polyester polyol with both acid and hydroxyl functionality. Like DMPA Polyol HA-0135, this resin is designed to eliminate the need for NMP as a processing solvent in the manufacturing of polyurethane dispersions. Technical Data Properties Hydroxyl Value, mgkoh / g Acid Value, mgkoh / g Acid Eq. Wt., g / eqv Hydroxyl Eq. Wt., g / eqv Colour, APHA < 250 max 25 C, grams / litre Moisture, % < C, poise 172

41 DMPA Polyol HA-0135LV2 - Technical Datasheet VIscosity HA-0135 vs HA-0135LV Visc Poise Insert table with Viscosity graph HA-0135 HA-0135LV Temperature C Increased Hydroxyl Concentration Increased coating hardness Chemical resistance Low Crystallinity Allows for ease of handling at lower temperatures Storage DMPA Polyol HA-0135LV2 is very hygroscopic. Container should be sealed at all times unless discharging. Due to the reactive nature of the material, containers should be tightly sealed and stored at 0-30 C. If preheating is required for discharging, DMPA Polyol HA-0135LV2 should be heated to a maximum temperature of 50 C for no longer than 48 hours. If the material is exposed to >50 C for extended periods of time, undesirable side reactions could occur that could cause variations in the properties of the prepared formulations. The shelf life of the material is six months after receipt of the material if stored in a sealed container at 0-30 C. All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Revised: May 2010

42 DMPA Polyol HC-0123 Product Data DMPA Polyol HC-0123 GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Unit C, Pate Court, North Place Cheltenham, Glos. GL50 4DY UK Tel: Fax: Website: TECHNICAL DATA SHEET DCPD and DCPD resins are common raw materials to both coatings and composite resin formulators. DCPD resins are recognised for a variety of properties such as tackifying, pigment dispersing and moisture / corrosion resistance. Most DCPD based resins are used in non-aqueous applications due to their limited functionality and extremely hydrophobic character. Through a unique process, a hydroxyl functional polymeric DCPD polyol - DMPA Polyol HC is now available. This resin allows formulators to take advantage of the properties of DCPD in a variety of resin formulations through the reactivity of the hydroxyl groups. DMPA Polyol HC-0123 can be used to prepare both solvent-borne and water-borne resins, including polyurethane dispersions. Technical Data Properties Appearance Amber Resin Acid value (as supplied), mgkoh / g 5.0 max Hydroxyl number (as supplied), mgkoh / g Non-volatile % 98 min Brookfield 25 C, cp % in NMP % in acetone % in mineral spirits Density, grams / litre Colour, Gardner (as supplied) 12 max Hydroxyl equiv. weight (as supplied), g / eqv Iodine value

43 DMPA Polyol HC Technical Datasheet Applications Polyurethane dispersions for direct to metal application can be prepared with excellent early water spot, wet adhesion and corrosion resistance properties (Refer to DMPA Polyol HC-0123 Technical Bulletins #1 and #2). Solubility in water miscible and low boiling aprotic solvents allows PUD chemists to formulate zero VOC or NMP free polyurethane dispersions for adhesive applications. The combination of DCPD and linear aliphatic hydrocarbons in the same molecule can be an advantage in formulating low HAPS UPR for composite applications. Moisture curable urethane pre-polymers can easily be prepared with aromatic or aliphatic isocyanates for direct to metal primer or adhesive applications. Water-borne and solvent-borne alkyd resins with improved moisture and corrosion resistance can be prepared by replacing a portion of the oil and polyol with DMPA Polyol HC All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Revised: October 2009

44 DMPA Polyol BA-0132 Product Data DMPA Polyol BA-0132 TECHNICAL DATA SHEET GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: DMPA Polyol BA-0132 is a low colour solid resin prepared through a unique process that combines DMPA Dimethylolpropionic Acid with bis-phenol A epoxy resins. The result is an aromatic polymeric polyol with a high concentration of primary hydroxyl groups that can be utilised in a variety of applications. Technical Data Appearance Properties Clear solid resin Acid value (as supplied), mgkoh / g 10.0 max GEO Specialty Chemicals, Ltd. Customer Service (Europe) Unit C, Pate Court, North Place Cheltenham, Glos. GL50 4DY UK Tel: Fax: TRIMET-EU@geosc.com Hydroxyl number (as supplied), mgkoh / g Non-volatile % Weight per gallon Colour, 60% nvm Hydroxyl Equivalent Weight, g / eqv. (as supplied) 98 min N/A 3 max Website: Melt Point DSC, C 60-70

45 DMPA Polyol BA Technical Datasheet Applications Co-resin for blending with polyesters, alkyds and acrylic in baking or ambient cure enamels for improved adhesion, corrosion resistance and tack-free time. Excellent cross-linking resin for two components urethanes and powder coatings. Reaction with unsaturated fatty acids will produce high solids air cured and forced cure one component epoxy primers. Further reactions with trimellitic anhydride (TMA) or acrylic acid will produce water-reducible epoxy esters or epoxy ester dispersions. The high concentration of primary hydroxyls makes DMPA Polyol BA-0132 an excellent building block for epoxy modified alkyd dispersions. DMPA Polyol BA-0132 can be easily acrylated due to the high concentration of primary hydroxyl groups. Acrylated DMPA Polyol BA-0132 can be used in combination with low viscosity acrylated polyethers and polyesters to produce high solids UV cure coatings with excellent hardness, chemical and scratch resistance. All information and data, including the formulations and procedures discussed herein, are believed to be correct. However, this should not be accepted as a guarantee of their accuracy, and confirming tests should be run in your laboratory or plant. No statement should be construed as a recommendation for any use which would violate any patent rights. Sales of all products are pursuant to terms and conditions included in GEO Specialty Chemicals sales documents. Nothing contained therein shall constitute a guarantee or warranty with respect to the products described or their use. Safety information regarding these products is contained in their Material Safety Data Sheets. Users of these products are urged to review and use this information. 2 Created: August 2010

46 TRIMET Trimethylolethane TRIMET Brand of Trimethylolethane (TME) PRODUCT TECHNICAL GUIDE GEO Specialty Chemicals, Inc. Paints & Coatings Group Customer Service (USA) 340 Mathers Road Ambler PA USA Tel: (Toll Free ) Fax: GEO Specialty Chemicals, Ltd. Customer Service (Europe) Unit C, Pate Court, North Place Cheltenham, Glos. GL50 4DY UK Tel: Fax: Website: TRIMET Trimethylolethane (TME), C 5 H 12 O 3 CH 2 OH CH 3 C CH 2 OH CH 2 OH CAS Registry No EINECS Registry No

Application Data MPDIOL Glycol MPDIOL Glycol in Polyester Resins for Low-VOC Waterborne Can or Coil Coatings

Application Data MPDIOL Glycol MPDIOL Glycol in Polyester Resins for Low-VOC Waterborne Can or Coil Coatings in Polyester Resins for General Information Key Features and Benefits MPDIOL glycol (2-methyl-1,3-propanediol) is a aliphatic diol with unique properties and high performance. Its branched structure imparts

More information

POLYTONE UA 810. Aldehyde Resin

POLYTONE UA 810. Aldehyde Resin An Aldehyde Resin which is yellowing resistant, practically soluble in almost all paint solvents and compatible with almost all coating raw material. Aldehyde Resin POLYOLS & POLYMERS PVT.LTD. C-1/58-59,

More information

Product Focus Customer Commitment Performance Flexibility

Product Focus Customer Commitment Performance Flexibility NAXCAT Acid Catalysts Product Focus Customer Commitment Performance Flexibility The Industry Leader for the Dependable Quality Difference Cost Effective Solutions-When Quality Counts NEASE Co manufactures

More information

Bio-based Solutions for High-Performance Polyurethane Adhesives. Angela Smits Bio-based Adhesives Conference 2013

Bio-based Solutions for High-Performance Polyurethane Adhesives. Angela Smits Bio-based Adhesives Conference 2013 Bio-based Solutions for High-Performance Polyurethane Adhesives Angela Smits Bio-based Adhesives Conference 213 Bio-based building blocks sustainable solutions CRODA: Naturally derived speciality chemicals

More information

MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION Product Name: Plastics Bonding UV Visible Light Adhesive Item Numbers MATERIAL SAFETY DATA SHEET Extreme 3106 UV curing Adhesive Product Use/Class: Extreme

More information

AROLON 6436 Product Code: Acrylic Polyol

AROLON 6436 Product Code: Acrylic Polyol March 216 Product Code: 9162- Acrylic Polyol DESCRIPTION is an acrylic polyol resin designed for high solids, high performance polyurethane coatings. Low VOC (42 grams per liter) polyurethane coatings

More information

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE COMPANY/UNDERTAKING

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE COMPANY/UNDERTAKING 1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE COMPANY/UNDERTAKING Product Name: Product Number: 60439, 60455 Date Prepared: 2/25/2004 Manufacturer: Telephone: MEDICAL EMERGENCY TRANSPORTATION

More information

MATERIAL SAFETY DATA SHEET Mercury 5 Min and 15 Min Epoxy. Mercury 5 Min Mercury 15 Min A

MATERIAL SAFETY DATA SHEET Mercury 5 Min and 15 Min Epoxy. Mercury 5 Min Mercury 15 Min A MATERIAL SAFETY DATA SHEET Mercury 5 Min and 15 Min Epoxy COMPANY NAME: Mercury Adhesives Inc ADDRESS: 6110 Parkway North Dr Cumming GA 30040 PHONE: 1 770-886-9566 TRADE NAME: CHEMICAL NAME: Mercury 5

More information

Araldite Advanced Materials. Two component toughened methacrylate adhesive system. Structural Adhesives TECHNICAL DATASHEET

Araldite Advanced Materials. Two component toughened methacrylate adhesive system. Structural Adhesives TECHNICAL DATASHEET Advanced Materials Araldite 2022-1 Structural Adhesives TECHNICAL DATASHEET Araldite 2022-1 Two component toughened methacrylate adhesive system Key properties Excellent ratio working time / cure time

More information

MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET MATERIAL SAFETY DATA SHEET SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION Product Name: Sign Bonder Activator Extreme EXT-410 Activator Item Numbers MANUFACTURER: Extreme Adhesives 63 Epping Road Raymond,

More information

MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET MATERIAL SAFETY DATA SHEET SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION Product Name: Metal Bonding-high performance 1;1 MMA Activator Item Numbers Extreme 5395GB Activator 09/05/13 1 of 5 MANUFACTURER:

More information

Fatty acid product guide

Fatty acid product guide Fatty acid product guide Kraton Corporation s Sylfat and Century fatty acids are useful in a wide range of industrial applications. These fatty acids (tall oil fatty acid, monomer acid, stearic acid and

More information

Versatic. Acids and Derivatives. Product Overview

Versatic. Acids and Derivatives. Product Overview Versatic Acids and Derivatives Product verview Hexion is the number one global supplier of Versatic acids and derivatives, primarily to the polymer, paints, coatings, construction and adhesives markets.

More information

PRIMAL HG-98 Binder. Pure Acrylic Polymer for Gloss and Semi-Gloss Paints

PRIMAL HG-98 Binder. Pure Acrylic Polymer for Gloss and Semi-Gloss Paints Technical Data Sheet PRIMAL HG-98 Binder Pure Acrylic Polymer for Gloss and Semi-Gloss Paints Regional Product Availability EMEA Description PRIMAL HG-98 Binder is a pure acrylic emulsion polymer designed

More information

MATERIAL SAFETY DATA SHEETS

MATERIAL SAFETY DATA SHEETS REVISED DEC./2014 1. CHEMICAL PRODUCT Adhesive Systems, Inc. 9411 Corsair Road Frankfort, IL 60423 1-800-552-0299 Phone 1-815-464-5650 Fax EMERGENCY PHONE 1-800-255-3924 International +01+813-248-0585

More information

Item number Item number Item number

Item number Item number Item number Tall Oil products product Distilled Tall Oil (DTO) Product name UCY10 UCY15 UCY20 UCY20-25 UCY25-30 UCY30-40 Item number 10-004 10-011 10-012 10-009 10-005 10-013 Page 3 4 5 6 7 8 Item number 10-006 10-007

More information

SURFACE COATINGS. Paint, Ink, Adhesives, Elastomers, Performance Coatings, UV Curing, Latex Emulsion

SURFACE COATINGS. Paint, Ink, Adhesives, Elastomers, Performance Coatings, UV Curing, Latex Emulsion SURFACE COATINGS Paint, Ink, Adhesives, Elastomers, Performance Coatings, UV Curing, Latex Emulsion Harcros Chemicals-Introduction 1 Since our inception in 1917, we have been committed to safety, quality

More information

Polycarbonate diol - Improving polyurethane durability in adhesives, coatings and pavements

Polycarbonate diol - Improving polyurethane durability in adhesives, coatings and pavements Polycarbonate diol - Improving polyurethane durability in adhesives, coatings and pavements Daniel Hernandes Sales Executive November 8 th, 2012 1 OUTLINE 1. Introduction: Polycarbonate diol 2. High-performance

More information

Protect-All Rapid Weld (Part B) Vendor. Contact: Phone: Web:

Protect-All Rapid Weld (Part B) Vendor. Contact: Phone: Web: 1 Page 1 of 5 PRODUCT AND COMPANY IDENTIFICATION Manufacturer Manufactured Exclusively for Vendor 5585 North Huron Avenue Oscoda, MI 48750 Contact: Phone: Info-Trac 1-800-535-5053 Contact: Phone: Web:

More information

CLiQSPERSE. CLiQFLOW. CLiQSMART

CLiQSPERSE. CLiQFLOW. CLiQSMART CLiQSPERSE CLiQFLOW CLiQSMART Product Overview Additives - 2018 CLiQSPERSE wetting and dispersing agents for non-aqueous CLiQSPERSE Product Chemistry Active Content Solvents / Diluents BA polymeric resin-like

More information

slight, characteristic colour Gardner max. 4

slight, characteristic colour Gardner max. 4 Castor oil CAS No. 8001-79-4 Castor oil (also known as Ricinus oil) is a vegetable oil extracted by mechanical pressing of the Castor seed. It is pale-yellowish or almost colorless with a mild characteristic

More information

Material Safety Data Sheet

Material Safety Data Sheet * * * Section 1 - Chemical Product and Company Identification * * * Part Number: 840 Product Use: Brake Fluid Manufacturer Information BG Products Inc. Phone: (316) 265-2686 701 S. Wichita Street Fax:

More information

Can Coil (PCM) E-Coat Elastomers/Foam General Industrial. 1051, NACORR 1552 Acrylic Anodic 188, XM-332, XM ,188, A308

Can Coil (PCM) E-Coat Elastomers/Foam General Industrial. 1051, NACORR 1552 Acrylic Anodic 188, XM-332, XM ,188, A308 While not all inclusive, this quick reference chart has been designed to offer starting point product choices by application, solvent based systems (font-black), solventless (font-green), waterborne (font-blue),

More information

Allylic alcohols improve acrylic polyols

Allylic alcohols improve acrylic polyols Allylic alcohols improve acrylic polyols Efforts to reduce the VOC content of two-component urethane coatings have focused primarily on lowering the molecular weight of the polyols. Unfortunately, the

More information

HPHP- A Component for Enviornmentally Advanced Coatings

HPHP- A Component for Enviornmentally Advanced Coatings HPHP- A Component for Enviornmentally Advanced Coatings m 2 fd- Don Morris Texas Eastman Division, P.O. Box 7444 Longview, Texas 75607 The coating s industry is undergoing a dramatic shift from solvent

More information

Eastman t-baa (tertiary-butyl acetoacetate)

Eastman t-baa (tertiary-butyl acetoacetate) Eastman t-baa (tertiary-butyl acetoacetate) for the synthesis of acetoacetyl-functional resins CH 3 O O H 3 C C O C CH 2 C CH 3 CH 3 Eastman t-baa Introduction Eastman t-baa (tertiary-butyl acetoacetate)

More information

MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET MATERIAL SAFETY DATA SHEET 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION REVISION DATE: 01/14/2010 PRODUCT NUMBER HMIS CODES 800014 Health 2 Flammability 1 Reactivity 1 PRODUCT NAME PPE X CA-40 LDI (US)

More information

MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET MATERIAL SAFETY DATA SHEET SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION Product Name: Sign Bonder Resin Item Numbers Product Use/Class: Extreme EXT-410 Clear, Extreme EXT-410 White Methyl Methacrylate

More information

MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET MATERIAL SAFETY DATA SHEET SECTION 1 - PRODUCT AND COMPANY Product Name: Jet Adhesive 5300 Resin Product Type: Methacrylate Adhesive Company Address: JET CHEMICAL PRODUCTS, Inc., Zona Franca Palmaseca

More information

Usable in formulations. Active content [%] Flash point [ C] Delivery form. Chemical description. Product. Solvent. Solvent free UV curing.

Usable in formulations. Active content [%] Flash point [ C] Delivery form. Chemical description. Product. Solvent. Solvent free UV curing. Product Chemical description Active content [%] Solvent ph-value Flash point [ C] Delivery form Usable in formulations Solvent free UV curing Solvent based Water based LUCRAMUL 1820 LIQ. LUCRAMUL AP LUCRAMUL

More information

Product Safety Assessment Propoxylated/Ethoxylated Ethylenediamine Polyol

Product Safety Assessment Propoxylated/Ethoxylated Ethylenediamine Polyol Product Safety Assessment Propoxylated/Ethoxylated Ethylenediamine Polyol Select a Topic: Names Product Overview Manufacture of Product Product Description Product Uses Exposure Potential Health Information

More information

BEPD butyl ethyl propane diol your glycol of choice for high performance polyester resins. Henrik Bernquist product manager Perstorp AB ECS 2013

BEPD butyl ethyl propane diol your glycol of choice for high performance polyester resins. Henrik Bernquist product manager Perstorp AB ECS 2013 BEPD butyl ethyl propane diol your glycol of choice for high performance polyester resins Henrik Bernquist product manager Perstorp AB ECS 2013 BEPD your glycol of choice for high performance polyester

More information

KEYWAX WX1014 RUBBER WAX CONCENTRATE

KEYWAX WX1014 RUBBER WAX CONCENTRATE PRODUCT DESCRIPTION ADVANTAGES KEYWAX WX1014 RUBBER WAX CONCENTRATE (TYPICAL PROPERTIES) These should not be considered as specifications. KEYWAX WX1014 is a is a blend of 15% polyisobutylene rubber in

More information

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE COMPANY/UNDERTAKING

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE COMPANY/UNDERTAKING 1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE COMPANY/UNDERTAKING Product Name: Product Number: 11757-04, 40551-02, 91388-05, 91748-05, 91757-06, 91757-20 Date Prepared: 2/26/2014 Manufacturer:

More information

MATERIAL SAFETY DATA SHEET PRODUCT: Magellan XPA Universal

MATERIAL SAFETY DATA SHEET PRODUCT: Magellan XPA Universal Product: Chemical Family: Product Use: Manufacturer: SECTION 1: PRODUCT AND COMPANY IDENTIFICATION Magellan XPA Universal Aromatic isocyanate Adhesive Magellan XPA P.O. Box 390425 Cambridge, MA 02139 Telephone

More information

MATERIAL SAFETY DATA SHEET (MSDS)

MATERIAL SAFETY DATA SHEET (MSDS) MATERIAL SAFETY DATA SHEET (MSDS) HEALTH: 2 FLAMMABILITY: 1 REACTIVITY: 1 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product Name: Trade Name: Codes and colours: Manufacturer name: Ultraviolet light

More information

FOOTBALL WHEN LEAKS MUST BE STOPPED! Material Safety Data Sheet FlowStop FootBall TM. 1. Product and Company Identification

FOOTBALL WHEN LEAKS MUST BE STOPPED! Material Safety Data Sheet FlowStop FootBall TM. 1. Product and Company Identification FOOTBALL WHEN LEAKS MUST BE STOPPED! 1. Product and Company Identification Material Safety Data Sheet FlowStop FootBall TM Product Name: FLOWSTOP FOOTBALL TM Supplier: LOGOS INC. P.O. Box 634, Denver,

More information

EMERGENCY PHONE MATERIAL SAFETY DATA SHEET MP5405/5430/5445 PART A (RESIN)

EMERGENCY PHONE MATERIAL SAFETY DATA SHEET MP5405/5430/5445 PART A (RESIN) 9411 Corsair Road Frankfort, IL 60423 1-800 - 552-0299 Phone 1-815 - 464-5650 Fax EMERGENCY PHONE 1-800 - 255-3924 MATERIAL SAFETY DATA SHEET MP5405/5430/5445 PART A (RESIN) HMIS HEALTH 2 FLAMMABILITY

More information

Polyester Diols. A comprehensive range of polyester diols that can be customized with flexibility and responsiveness. It s all about the chemistry

Polyester Diols. A comprehensive range of polyester diols that can be customized with flexibility and responsiveness. It s all about the chemistry Polyester Diols A comprehensive range of polyester diols that can be customized with flexibility and responsiveness Formulators can achieve specific properties geared to the final application with our

More information

MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET SECTION 1: PRODUCT AND COMPANY IDENTIFICATION Product: Q-Seal 290S (grey/black) Chemical Family: Polyurethane prepolymer Product Use: Loop detector sealant Responsible Party: Chemque, Inc. 266 Humberline

More information

MATERIAL SAFETY DATA SHEET PRODUCT: Fortane One SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

MATERIAL SAFETY DATA SHEET PRODUCT: Fortane One SECTION 1: PRODUCT AND COMPANY IDENTIFICATION Product: Chemical Family: Product Use: Manufacturer: SECTION 1: PRODUCT AND COMPANY IDENTIFICATION Fortane One Aromatic isocyanate Adhesive Chemque, Inc. 266 Humberline Drive Rexdale, ON M9W 5X1 CANADA

More information

Material Safety Data Sheet MSDS ID: CR-156

Material Safety Data Sheet MSDS ID: CR-156 * * * Section 1 - Chemical Product and Company Identification * * * PRODUCT NAME: Thermo-Gel 300L Chemical Name: Anionic Emulsion Copolymer of acrylamide Manufacturer Information Thermo Technologies, LLC.

More information

CASTING BANDAGES WITHOUT FIBREGLASS

CASTING BANDAGES WITHOUT FIBREGLASS SECTION 1 IDENTIFICATION OF THE MATERIAL AND SUPPLIER Product Product Name CASTING BANDAGES WITHOUT FIBREGLASS Other Names DELTA-CAST ELITE DELTA-CAST PRINTS DELTA-CAST SOFT Manufacturer s Product Code

More information

Defoaming Surfactants

Defoaming Surfactants TERGITOL L Series Biodegradable Surfactants TERGITOL L-61 E, L-62 E, L-64 E, L-81 E Defoaming Surfactants Trademark of The Dow Chemical Company ( Dow ) or an affiliated company of Dow. These surfactants

More information

BALANCE RCF Polymer. INCI: Acrylates/Ceteareth-20 Methacrylate Crosspolymer. Cost Effective Fixative and Rheology Modifier

BALANCE RCF Polymer. INCI: Acrylates/Ceteareth-20 Methacrylate Crosspolymer. Cost Effective Fixative and Rheology Modifier AkzoNobel Surface Chemistry INCI: Acrylates/Ceteareth-2 Methacrylate Crosspolymer Cost Effective Fixative and Rheology Modifier INTRODUCTION Traditionally, anionic polymers are not compatible with Carbomer.

More information

Tektamer 38 A.D. Product Information. Dibromodicyanobutane dispersion, VOC-free 1/9

Tektamer 38 A.D. Product Information. Dibromodicyanobutane dispersion, VOC-free 1/9 Product Information Tektamer 38 A.D. Dibromodicyanobutane dispersion, VOC-free Tektamer is a registered trademark of LANXESS Corporation. Page 1 of 9: This document contains important information and must

More information

Chemical Name: Interior Acrylic Latex. Manufacturer: Sherwin Williams. Container size: 1 gallon. Location: VLA

Chemical Name: Interior Acrylic Latex. Manufacturer: Sherwin Williams. Container size: 1 gallon. Location: VLA Chemical Name: Interior Acrylic Latex Manufacturer: Sherwin Williams Container size: 1 gallon Location: VLA Disposal: Place empty container in trash. MATERIAL SAFETY DATA SHEET 20 00 DATE OF PREPARATION

More information

WE INVEST IN CAPACITY AND QUALITY.

WE INVEST IN CAPACITY AND QUALITY. WE INVEST IN CAPACITY AND QUALITY. Epilox EPOXY RESINS Epilox REACTIVE DILUENTS Epilox HARDENERS Epilox systems Binders for paints and coatings PRODUCT CATALOGUE 2 Epilox SYSTEMS: PROVEN, SUCCESSFUL, INNOVATIVE.

More information

Emergency telephone Gorilla Glue Europe A/S. Tel: The Gorilla Glue Company. Tel: 001 (513)

Emergency telephone Gorilla Glue Europe A/S. Tel: The Gorilla Glue Company. Tel: 001 (513) SAFETY DATA SHEET Gorilla Super Glue 1. IDENTIFICATION OF THE PREPARATION AND OF THE COMPANY Product name Product type Intended use Supplier Gorilla Super Glue Cyanoacrylate adhesive Adhesive for wood,

More information

Modified alkyd emulsions for waterborne coatings

Modified alkyd emulsions for waterborne coatings Modified alkyd emulsions for waterborne coatings Authors: Company: Contact: Dr. Carolin Wallenhorst Reinhard Winter ASK Chemicals GmbH Dieselstraße 35 41, 42489 Wülfrath, Germany www.ask-chemicals.com

More information

Material Safety Data Sheet

Material Safety Data Sheet * * * Section 1 - Chemical Product and Company Identification * * * Part Number: 711 (All Sizes) Product Use: Flush for vehicle air conditioning system Manufacturer Information BG Products Inc. Phone:

More information

DESMOLUX RADIATION CURING RESINS. All About Resins.

DESMOLUX RADIATION CURING RESINS. All About Resins. DESMOLUX RADIATION CURING RESINS www.allnex.com All About Resins FACTS & FIGURES With manufacturing, R&D and technical facilities located throughout Europe, North America, Asia Pacific and Latin America,

More information

MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET Gruber Systems, Inc. MATERIAL SAFETY DATA SHEET 1 of 5 SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION : Modified Methacrylate Resin for Seamless Rapid Cure Two Part Adhesive Item Numbers Product Use/Class:

More information

Randolph Products Company, 33 Haynes Circle, Chicopee, MA 01020

Randolph Products Company, 33 Haynes Circle, Chicopee, MA 01020 Page: 1 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION (See top of page) 2. COMPOSITION/INFORMATION ON INGREDIENTS Component/Exposure Limits CAS# % by Wt. -------------------------------------------------------------------------------------

More information

KEY PRODUCT FOR HL SAFETY DATA SHEET

KEY PRODUCT FOR HL SAFETY DATA SHEET January 2012 KEY PRODUCT FOR HL SAFETY DATA SHEET SECTION 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product name Synonym Use Chemical formula Registration numbers Manufacturer/Supplier Address Key

More information

Product Safety Assessment VORANOL VORACTIV Polyols

Product Safety Assessment VORANOL VORACTIV Polyols Product Safety Assessment VORANOL VORACTIV Polyols Select a Topic: Names Product Overview Manufacture of Product Product Description Product Uses Exposure Potential Health Information Environmental Information

More information

Determination of the acid value (AV) Application Bulletin 200/3 e. Electrodes Solvotrode easyclean

Determination of the acid value (AV) Application Bulletin 200/3 e. Electrodes Solvotrode easyclean Determination of the acid value, hydroxyl value, and Branch General analytical chemistry; organic chemistry, chemistry; plastics, photographic industry Keywords Titration; potentiometric titration; automation;

More information

Methacrylate adhesive with good thermal stability. Good adhesion even without particular pretreatment. Mix ratio Parts by weight Parts by volume

Methacrylate adhesive with good thermal stability. Good adhesion even without particular pretreatment. Mix ratio Parts by weight Parts by volume Advanced Materials Araldite 2052-1 Structural Adhesives TECHNICAL DATA SHEET Araldite 2052-1 Methacrylate adhesive with good thermal stability Key properties Fast curing Very high temperature resistance

More information

WATERBASED RADIATION-CURABLE POLYURETHANE ACRYLATE COATINGS

WATERBASED RADIATION-CURABLE POLYURETHANE ACRYLATE COATINGS WATERBASED RADIATI-CURABLE PLYURETAE ACRYLATE CATIGS by Y. eischkel*, K. Menzel+, E. Beck+, K.. Sass&, C. A. Glotfelter, F. Masson#, C. Decker#, and R. Schwalm*, BASF AG, *Polymer Research Laboratory,

More information

VANFRE Processing Aids

VANFRE Processing Aids VANFRE s High performance solutions for your processing needs CONTENTS Vanderbilt Chemicals, LLC 30 Winfield Street, P.O. Box 5150 Norwalk, CT 06856-5150 Phone: (203) 853-1400 Fax: (203) 838-6368 E-Mail:

More information

2002 =========================================================================== Section 1 PRODUCT AND COMPANY IDENTIFICATION

2002 =========================================================================== Section 1 PRODUCT AND COMPANY IDENTIFICATION WL1111100 WL3333300 MATERIAL SAFETY DATA SHEET 2002 Section 1 PRODUCT AND COMPANY IDENTIFICATION PRODUCT IDENTIFICATION HMIS CODES Health 3* WHITE LIGHTNING* STOP GAP!* Insulating Foam Flammability 4 Reactivity

More information

TO COMPLY WITH OSHA HAZARD COMMUNICATION STANDARD 29 CFR & THE GLOBALLY HARMONIZED SYSTEM OF CLASSIFICATION AND LABELLING OF CHEMICALS

TO COMPLY WITH OSHA HAZARD COMMUNICATION STANDARD 29 CFR & THE GLOBALLY HARMONIZED SYSTEM OF CLASSIFICATION AND LABELLING OF CHEMICALS TO COMPLY WITH OSHA HAZARD COMMUNICATION STANDARD 29 CFR.1910.1200 & THE GLOBALLY HARMONIZED SYSTEM OF CLASSIFICATION AND LABELLING OF CHEMICALS 1. PRODUCT AND COMPANY IDENTIFICATION 1.1 Product Identifier

More information

INVISTA TERRIN Polyols

INVISTA TERRIN Polyols Technical Data Sheet INVISTA TERRIN Polyols Cost-Effective Alternative to Conventional Polyether and Polyester Polyols Introduction TERRIN polyols can be used in lieu of or in combination with conventional

More information

CLiQSPERSE. CLiQFLOW. CLiQSMART

CLiQSPERSE. CLiQFLOW. CLiQSMART CLiQSPERSE CLiQFLOW CLiQSMART Product Overview Additives - 2017 CLiQSPERSE wetting and dispersing agents for non-aqueous CLiQSPERSE Product Chemistry Active Content Solvents / Diluents BA polymeric resin-like

More information

Barium Sulphate Pw21 Product Code: EX-SU0020 Department: inert pigments & fillers C.A.S.:

Barium Sulphate Pw21 Product Code: EX-SU0020 Department: inert pigments & fillers C.A.S.: Material Safety Data Sheet Barium Sulphate Pw21 Product Code: EX-SU0020 Department: inert pigments & fillers C.A.S.: 7727-43-7 Section: 1 Identification PRODUCT USE CHEMICAL FAMILY. SYNONYMS Industrial.

More information

SECTION 1 - IDENTIFICATION

SECTION 1 - IDENTIFICATION 1 of 5 11/25/2009 9:53 AM TARKSOL GREEN Tarksol Aqua Kleen C Material Safety Data Sheet Trade Name: Tarksol Aqua Kleen C Manufacturer: Tarksol, Inc. 3400 Ridge Road West, S-300 Rochester, New York 14626

More information

Acid & Blocked Acid Catalysts

Acid & Blocked Acid Catalysts & & Blocked Catalysts & ACID & BLOCKED ACID CATALYSTS Why Use Catalysts? Today s need for high solids and waterborne coatings requires greater use of high reactivity, low viscosity resins and crosslinkers.

More information

TECHNICAL DATA SHEET GROWCLEAR PLUS

TECHNICAL DATA SHEET GROWCLEAR PLUS TECHNICAL DATA SHEET GROWCLEAR PLUS CATHODIC ELECTROPHORETIC CLEAR / TINTED LACQUERING PROCESS Introduction Growclear Plus is an advanced version of the earlier popular electrophoretic Clearlyte lacquer.

More information

MATERIAL SAFETY DATA SHEET DATE: FEB 21, 2011 NAIL GLUE Page 1 of 4

MATERIAL SAFETY DATA SHEET DATE: FEB 21, 2011 NAIL GLUE Page 1 of 4 MATERIAL SAFETY DATA SHEET DATE: FEB 21, 2011 NAIL GLUE Page 1 of 4 SECTION 1:. PRODUCT AND COMPANY IDENTIFICATION PRODUCT NAME: NAIL GLUE PRODUCT TYPE: cyanoacrylate adhesive PRODUCT USE: fingernail adhesive

More information

Materials Safety Data Sheet DUPLI-COLOR Enamel Paint, Semi-Gloss Black

Materials Safety Data Sheet DUPLI-COLOR Enamel Paint, Semi-Gloss Black Materials Safety Data Sheet 100510 DUPLI-COLOR Enamel Paint, Semi-Gloss Black DA1603 08 00 DATE OF PREPARATION Nov 28, 2010 SECTION 1 PRODUCT AND COMPANY IDENTIFICATION PRODUCT NUMBER DA1603 PRODUCT NAME

More information

Dextrol and Strodex Surfactant Selection Guide

Dextrol and Strodex Surfactant Selection Guide Dextrol and Strodex Surfactant Selection Guide Complete solutions for coatings Dextrol and Strodex phosphate ester surfactants from Ashland Aqualon Functional Ingredients are leading technologies within

More information

Fortane MVS Ultra Moisture Vapor Urethane Membrane

Fortane MVS Ultra Moisture Vapor Urethane Membrane Product: SECTION 1: PRODUCT AND COMPANY IDENTIFICATION Fortane MVS Ultra Moisture Vapor Urethane Membrane Chemical Family: Product Use: Manufacturer: Aromatic isocyanate Adhesive Chemque, Inc. 6101 Guion

More information

SAFETY DATA SHEET. Global Agri-trade Corp. 320 Golden Shore, Suite 350 Long Beach, CA Tel. No.: (562) Fax No.

SAFETY DATA SHEET. Global Agri-trade Corp. 320 Golden Shore, Suite 350 Long Beach, CA Tel. No.: (562) Fax No. 1) Product and Company Information SAFETY DATA SHEET Product Name: Product Description: Material Use: Supplier: NURISOL Calcium Salts of Long Chain Fatty Acids for ruminants Livestock Feedstuff Global

More information

Suitability of (Meth)acrylates for Use in Sealant Applications

Suitability of (Meth)acrylates for Use in Sealant Applications Suitability of (Meth)acrylates for Use in Sealant Applications James E. Goodrich Sartomer USA, LLC 2 Thomas Jones Way Exton, PA, USA 19341 Abstract The use of (meth)acrylates in peroxide or amine cured

More information

Material Safety Data Sheet

Material Safety Data Sheet Material Safety Data Sheet zymöl enterprises, inc. 191 Champion Drive Brooksville, FL 34601 1. PRODUCT AND COMPANY IDENTIFICATION PRODUCT NAME PRODUCT CODE CHEMICAL FAMILY CHEMICAL NAME FORMULA ZYMÖL LEATHER

More information

Isopropyl Alcohol Wipe 99.9% Pure Anhydrous 824-W Technical Data Sheet

Isopropyl Alcohol Wipe 99.9% Pure Anhydrous 824-W Technical Data Sheet Technical Data Sheet Description The Isopropyl Alcohol Wipe is a high purity, multipurpose cleaner. The wipe is good at dissolving dirt, light organic contaminants, and ionic flux residues. Since the is

More information

Material Safety Data Sheet

Material Safety Data Sheet Material Safety Data Sheet Revision Date: 05/19/2005 Issue date: 05/19/2005 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product type: Epoxy Hardener Region: United States Company address: Contact Information:

More information

G-TEX HA is packed in non-returnable, internal-lined metal drums of net weight 205kg or delivered in larger bulk quantities using appropriate tanks.

G-TEX HA is packed in non-returnable, internal-lined metal drums of net weight 205kg or delivered in larger bulk quantities using appropriate tanks. G-TEX HA G-TEX HA X01/R1/S0126 G-TEX HA is a natural rubber latex concentrate obtained by centrifugation and preserved with a high amount of ammonia. It is a general purpose latex and is widely used in

More information

Products for unsaturated polyesters Fortifying quality & durability

Products for unsaturated polyesters Fortifying quality & durability Products for unsaturated polyesters Fortifying quality & durability The elements of success You need a partner who can see the big picture when it comes to your products, your processes and your customers.

More information

MATERIAL SAFETY DATA SHEET MSDS NUMBER: MSDS-350 ISSUE DATE: 9/1/15 PAGE 1 OF 5

MATERIAL SAFETY DATA SHEET MSDS NUMBER: MSDS-350 ISSUE DATE: 9/1/15 PAGE 1 OF 5 MSDS NUMBER: MSDS-350 ISSUE DATE: 9/1/15 PAGE 1 OF 5 1. PRODUCT IDENTIFICATION Product Name Trexel TecoCell H1 Chemical Foam Concentrate Emergency Phone: 1-973-627-4070 (U.S.A.) Medical Emergency Phone:

More information

MITIGATING CHEMICALS OF CONCERN THROUGH THE USAGE OF NOVEL ENERGY CURABLE ACRYLATE TECHNOLOGY

MITIGATING CHEMICALS OF CONCERN THROUGH THE USAGE OF NOVEL ENERGY CURABLE ACRYLATE TECHNOLOGY MITIGATING CHEMICALS OF CONCERN THROUGH THE USAGE OF NOVEL ENERGY CURABLE ACRYLATE TECHNOLOGY Philippe DeGroote, Paul Gevaert, Luc Lindekens, Colette Moulaert, Rosalyn Waldo (Allnex) and Mike Rester, Andrea

More information

Development of Suitable Methodology to Synthesize Terephthalic Acid Based Alkyd Resin

Development of Suitable Methodology to Synthesize Terephthalic Acid Based Alkyd Resin Development of Suitable Methodology to Synthesize Terephthalic Acid Based Alkyd Resin Udayakumara S.V. 1, Gunapala O. 2 1 B.Sc Engineering (Moratuwa,SL), 2 PhD(Moscow) 1 Department of Materials Science

More information

There are no supported uses of propylene oxide in consumer products.

There are no supported uses of propylene oxide in consumer products. Global Product Strategy (GPS) Safety Summary Propylene Oxide This GPS Safety Summary is a high-level summary intended to provide the general public with an overview of product safety information on this

More information

MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET MATERIAL SAFETY DATA SHEET 1. COMPANY AND PRODUCT IDENTIFICATION DUNCAN ENTERPRISES EMERGENCY TELEPHONE NUMBERS 5673 East Shields Avenue Health Emergency: 559-291-4444 7:00 am 3:30 pm Fresno, CA 93727

More information

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE COMPANY/UNDERTAKING

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE COMPANY/UNDERTAKING 1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE COMPANY/UNDERTAKING Product Name: Alcohol; Kimberly-Clark Professional Moisturizing Instant Product Number: 91562, 92562, 93044, 93047, 93050, 93053,

More information

Material Safety Data Sheet

Material Safety Data Sheet * * * Section 1 - Chemical Product and Company Identification * * * Part Number: 750 (All Sizes) Product Use: Synthetic 75W90 Gear Oil Manufacturer Information BG Products Inc. Phone: (316) 265-2686 701

More information

There are no supported uses of Allyl Alcohol in direct consumer products or applications.

There are no supported uses of Allyl Alcohol in direct consumer products or applications. Global Product Strategy (GPS) Safety Summary Allyl Alcohol This GPS Safety Summary is a high-level summary intended to provide the general public with an overview of product safety information on this

More information

SURFONIC. Performance Emulsifiers for Metalworking Fluids

SURFONIC. Performance Emulsifiers for Metalworking Fluids SURFONIC Performance Emulsifiers for Metalworking Fluids SURFONIC Performance Emulsifiers for Metalworking Fluids Metalworking Fluids Processes such as high-speed machining create increased pressure for

More information

METOLOSE: CONTENTS PAGE

METOLOSE: CONTENTS PAGE METOLOSE: CONTENTS PAGE 2 Preface What is Metolose Substitution types Specifications 1) Available grades & viscosity 2) Nomenclature 3) Packaging Characteristics of Metolose Properties of Metolose 1) Powder

More information

Date Printed: 03/03/2004 Date Updated: 09/04/2002 Version 1.2. Product Name HEXADECANE, ANHYDROUS, 99+% Product Number

Date Printed: 03/03/2004 Date Updated: 09/04/2002 Version 1.2. Product Name HEXADECANE, ANHYDROUS, 99+% Product Number SIGMA-ALDRICH MATERIAL SAFETY DATA SHEET Date Printed: 03/03/2004 Date Updated: 09/04/2002 Version 1.2 Section 1 - Product and Company Information Product Name HEXADECANE, ANHYDROUS, 99+% Product Number

More information

Lubricants for plastic processing licowax, Licolub, Licocene, licomont

Lubricants for plastic processing licowax, Licolub, Licocene, licomont Lubricants for plastic processing licowax, Licolub, Licocene, licomont Lubricants for plastic processing LICOWAX, LICOLUB, LICOCENE, LICOMONT Montan waxes For highly demanding plastic applications, our

More information

Calcium Carbonate Chalk -coarse 21um Product Code: EX-CA0035 Department: inert pigments & fillers C.A.S.: , ,

Calcium Carbonate Chalk -coarse 21um Product Code: EX-CA0035 Department: inert pigments & fillers C.A.S.: , , Material Safety Data Sheet Calcium Carbonate Chalk -coarse 21um Product Code: EX-CA0035 Department: inert pigments & fillers C.A.S.: 1317-65-3, 14808-60-7, Section: 1 Identification Product name Product

More information

MSDS Material Safety Data Sheet

MSDS Material Safety Data Sheet 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION PRODUCT NUMBER PRODUCT NAME MANUFACTURER PERMABOND LLC 14 Robinson Street Pottstown, PA 19464 EMERGENCY PHONES: MEDICAL 1 866 827 6282 TRANSPORT (CHEMTREC)

More information

SECTION 1. PRODUCT & COMPANY INFORMATION

SECTION 1. PRODUCT & COMPANY INFORMATION MATERIAL SAFETY DATA SHEET SECTION 1. PRODUCT & COMPANY INFORMATION Brand Name : MetaClaw DS Product Name : Ethylene Di Amine Tetra - Acetic Acid Di Sodium CAS No. : 6381-92-6 Supplier : Satyajit Chemicals

More information

ACRYSOL TT-615 Rheology Modifier

ACRYSOL TT-615 Rheology Modifier ACRYSOL TT-615 Rheology Modifier Description ACRYSOL TT-615 is a hydrophobically modified anionic thickener, designed to give a very pseudoplastic profile in interior/exterior latex paints. ACRYSOL TT-615

More information

Performance Additives. A-C Performance Additives WATER-BASED EMULSIONS

Performance Additives. A-C Performance Additives WATER-BASED EMULSIONS Performance Additives A-C Performance Additives WATER-BASED EMULSIONS Honeywell Gives You Every Advantage Honeywell s A-C Performance Additives help you make a wide variety of water-based emulsions that

More information

Chemical Name: Complex Chloride Sodium Chloride, Potassium Chloride, Magnesium Chloride, Calcium Chloride

Chemical Name: Complex Chloride Sodium Chloride, Potassium Chloride, Magnesium Chloride, Calcium Chloride 1. PRODUCT AND COMPANY IDENTIFICATION Product Identity: MeltDown Near Zero Chemical Name: Complex Chloride Sodium Chloride, Potassium Chloride, Magnesium Chloride, Calcium Chloride Recommended use of the

More information

: EPDM REPAIR TAPE - 6" CURED

: EPDM REPAIR TAPE - 6 CURED SECTION 1 - PRODUCT IDENTIFICATION Trade name Product code COMPANY Telephone Emergency Phone: Product use : : 68106B503 : Tremco Incorporated 3735 Green Road Cleveland, OH 44122 : (216) 292-5000 8:30-5:00

More information

Material Safety Data Sheet

Material Safety Data Sheet * * * Section 1 - Chemical Product and Company Identification * * * Part Number: 310, 310WOR, 31032, 3101, 31030, 31053 Product Use: Automatic Transmission Additive Manufacturer Information BG Products

More information