Advance Dental Simulation Module on Crown Preparation

Transcription

1 Advance Dental Simulation Module on Crown Preparation Ranier M. Adarve, DMD, MS, MHPE Prosthodontist and Instructional Designer

2 Introduction Welcome! This module is developed to guide dental students in preparing Full Crown restoration using the Advance Dental Simulation Technology-DentSim. The first part of the module covers the Principles of Preparation for Gold Crown Restoration for Tooth #19 (36) as prescribed by DentSim. The second part of the module covers the suggested step by step procedure in completing full crown preparation. At the end of the module, students are required to complete the test to evaluate performance.

3 Objectives Upon completion of this module, you will be able to: a. Understand the Principles of Preparation b. Identify the specific dimensions, forms and measurements of tooth reductions. c. Prepare accurately tooth #19 to receive Gold Crown restoration.

4 Part 1 Principles of Preparing Tooth #19 for Gold Crown Restoration

5 Tips There are 16 Principles of Tooth Preparation for Gold Crown Restoration as prescribed by the DentSim. Each of the principle will be listed in chronological order. More information will be provided by clicking the info button Use the forward arrow to navigate through the course and backward arrow if you need to review the previous slide. You may need to take down notes to remember all the dimensions and angulations for tooth reduction. Good luck!

6 1. The minimum necessary tooth structure is removed. 2. No damage to adjacent teeth. 3. No undercut exists.

7 4. In the occlusal surface appear 5 cusps: ML, DL, MB, B, and DB. These cusps follow the original contour of the tooth cusps and preserve the occlusal anatomy.

8 5. The tips of the cusps are located under the tips of the original cusps of the tooth.

9 6. Occlusal reduction: B cusps mm L cusps 1.0 mm

10 7. Functional cusps beveling is located on the buccal cusps, its width 1.0mm. 1.0

11 8. Taper of opposing walls: The M and D walls have taper of 4-6. The B and L walls have taper of 4-6.

12 9. Height of contour of the preparation walls is located parallel to the original height of contour of the enamel surface. 10.The buccal walls have 3 surfaces: from the margin to the HOC, from the HOC to the Functional Bevel, and the Functional Bevel. Height of Contour (HOC) 3 2 Height of Contour (HOC) 1

13 11. The lingual cusps have 2 surfaces: from the margin to the HOC, and from the HOC to the tip of the cusp. 12. The gradual change in the surfaces begins between the transitional line angles. 13. All the line angles of the walls and the cusps are rounded. All walls are smooth. Height of Contour (HOC) 2 1

14 14. Marginal geometry: chamfer configuration. The anatomy of the chamfer was created according to the shape of a round-end taper diamond bur, 0.8mm at its tip. 15. Axial reduction / chamfer width: Buccal chamfer width 0.5 mm Lingual chamfer width mm.

15 16. Margins are located 1.0mm occlusal to the free gingival line. As a result of the margin location, clearance is left from the adjacent teeth.

16 Procedure Evaluation Passing grade 60 Test Damage to adjacent tooth Pulp exposure Undercut 10 Occlusal reduction 12 Wall incline 16 Retention 10 Resistance (hinge movement) Grade Point reduced only in runtime Point reduced only in runtime 10 Wall smoothness 10 Margin location 6 Margin width 10 Finish line continuity 10 Interproximal clearance 6

17 Part 2 Step by Step Procedure

18 Tips There are 9 suggested step by step procedures. For beginners, it is best to follow the recommended sequence. Otherwise, you may proceed in the order that you are most comfortable with.

19 Preparation Steps 1. Occlusal Depth Guides 2. Occlusal Reduction 3. Mesial Reduction 4. Distal Reduction 5. Buccal Reduction 6. Lingual Reduction 7. Functional Cusp Bevel 8. Finishing the Preparation 9. Evaluating the Preparation

20 Step 1 Occlusal Depth Guides

21

22

23

24

25 Step 2 Occlusal Reduction

26

27

28

29 Step 3 Mesial Reduction

30

31

32

33

34

35 Step 4 Distal Reduction

36

37

38

39 Step 5 Buccal Reduction

40

41

42

43 Step 6 Lingual Reduction

44

45

46

47 Step 7 Functional Cusp Bevel

48

49 Step 8 Finishing the Preparation

50

51

52 Step 9 Evaluating the Preparation

53

54

55