Table of Contents Alliance Revision Balance Stanmore Bio-Moore II Taperloc Mallory-Head P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Answer Design Features: Forged cobalt chrome approximately twice the fatigue strength of cast CoCr. Interlok finish enhances cement-to-implant bonding. 3 bi-planar taper to promote compressive loading vs. shear of the cement mantle. Integrated A/P spacers to centralize proximally to allow for uniform cement mantle. PMMA distal centralizer to guard against varus or valgus positioning. Lateralized option Morse taper is shifted 6mm medially without altering leg length. Duckbill collar stresses the medial calcar and helps prevent subsidence of the stem. Reduced medial aspect allows for a 3.5mm proximal/medial cement mantle. Alliance instrumentation. The Answer is marketed for use with bone cement in the United States. Answer, Alliance and Interlok are registered trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Answer Answer Femoral Components Answer Distal Stem Positioners Lateralized 162601 162602 162603 162604 162605 162501 162502 162503 162504 162505 9 x 125mm 11 x 135mm 13 x 145mm 15 x 155mm 17 x 165mm 162656 162640 162657 162641 162658 162642 162659 162643 162660 162644 162661 162646 9mm 10mm 11mm 12mm 13mm 14mm 15mm 16mm 17mm 18mm 19mm 20mm
Bi-Metric Head/Neck Design Features: Forged cobalt chrome approximately twice the fatigue strength of cast CoCr. Interlok finish enhances cement-to-implant bonding. 3 bi-planar taper to promote compressive loading vs. shear of the cement mantle. Lateral flange holes for reattachment of trochanter. PMMA distal centralizer guards against varus or valgus positioning. Medial keel for rotational stability. 34, 45, 55mm resection levels 9, 11, 13 and 15mm diameters. 150mm, 200mm and 250mm lengths. Alliance instrumentation. The Bi-Metric Head/Neck is marketed for use with bone cement in the United States. Bi-Metric, Interlok and Alliance are registered trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Bi-Metric Head/Neck 150mm 12-162380 12-162381 12-162382 12-162383 12-162384 12-162385 12-162386 12-162387 12-162388 200mm 12-162480 12-162481 12-162482 12-162489 12-162483 12-162484 12-162485 12-162490 12-162486 12-162487 12-162488 12-162491 9 x 34 x 150mm 11 x 34 x 150mm 13 x 34 x 150mm 9 x 45 x 150mm 11 x 45 x 150mm 13 x 45 x 150mm 9 x 55 x 150mm 11 x 55 x 150mm 13 x 55 x 150mm 9 x 34 x 200mm 11 x 34 x 200mm 13 x 34 x 200mm 15 x 34 x 200mm 9 x 45 x 200mm 11 x 45 x 200mm 13 x 45 x 200mm 15 x 45 x 200mm 9 x 55 x 200mm 11 x 55 x 200mm 13 x 55 x 200mm 15 x 55 x 200mm 250mm Left 12-162580 12-162582 12-162584 12-162574 12-162586 12-162588 12-162590 12-162576 12-162592 12-162594 12-162596 12-162578 PMMA Centering Sleeves 162907 162909 162911 162913 162915 162917 250mm Right 7mm 9mm 11mm 13mm 15mm 17mm 12-162581 12-162583 12-162585 12-162575 12-162587 12-162589 12-162591 12-162577 12-162593 12-162595 12-162597 12-162579 9 x 34 x 250mm 11 x 34 x 250mm 13 x 34 x 250mm 15 x 34 x 250mm 9 x 45 x 250mm 11 x 45 x 250mm 13 x 45 x 250mm 15 x 45 x 250mm 9 x 55 x 250mm 11 x 55 x 250mm 13 x 55 x 250mm 15 x 55 x 250mm
Bi-Metric X-Series Porous Primary Design Features: Net-forged Ti alloy provides precise and consistent development of hip implants and related instrumentation. Proximal 1/3 PPS coated. 3 bi-planar taper. Collared in standard offset with neck angle of 140. Non-collared in standard offset with neck angle of 135 and 130 for lateralized option. Offset option increases proportionally based on stem size (5 9mm of additional offset). Medialized insertion hole. HA option over porous plasma spray. Use only with Exact Alliance Instrumentation. Bi-Metric, Alliance, Exact and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Bi-Metric X-Series Porous Primary Non-Collared Part No. Collared Part No. Collarless Lat. Part No. HA* Standard HA* Lateralized X180307 X180308 X180309 X180310 X180311 X180312 X180313 X180314 X180315 X180316 X180317 X180318 X180319 X180320 X180321 X181307 X181308 X181309 X181310 X181311 X181312 X181313 X181314 X181315 X181316 X181317 X181318 X181319 X181320 X181321 X11-180308 X11-180309 X11-180310 X11-180311 X11-180312 X11-180313 X11-180314 X11-180315 X11-180316 X11-180317 X11-180318 X11-180319 X11-180320 X11-180321 7 x 115mm 8 x 120mm 9 x 125mm 10 x 130mm 11 x 135mm 12 x 140mm 13 x 145mm 14 x 150mm 15 x 155mm 16 x 160mm 17 x 165mm 18 x 170mm 19 x 175mm 20 x 180mm 21 x 185mm X21-180307 X21-180308 X21-180309 X21-180310 X21-180311 X21-180312 X21-180313 X21-180314 X21-180315 X21-180316 X21-180317 X21-180318 X21-180319 X21-180320 X21-180321 X21-182308 X21-182309 X21-182310 X21-182311 X21-182312 X21-182313 X21-182314 X21-182315 X21-182316 X21-182317 X21-182318 X21-182319 X21-182320 X21-182321 7mm 8mm 9mm 10mm 11mm 12mm 13mm 14mm 15mm 16mm 17mm 18mm 19mm 20mm 21mm * HA offered in collarless option only.
Bio-Groove HA Design Features: Forged Ti alloy. Interlok finish enhances cement-to-implant bonding. Proximal 1/3 HA coated (Hydroxyapatite) promotes bony ingrowth in the HA coated grooved surface. 3 bi-planar taper. 50 micron coating of HA. Large V shaped grooves on proximal 1/3 promotes bony interdigitation. Collarless. Alliance instrumentation. Bio-Groove, Interlok and Alliance are registered trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Bio-Groove HA 11-162807 11-162808 11-162809 11-162810 11-162811 11-162812 11-162813 11-162814 11-162815 11-162816 11-162817 11-162818 11-162819 7 x 115mm 8 x 120mm 9 x 125mm 10 x 130mm 11 x 135mm 12 x 140mm 13 x 145mm 14 x 150mm 15 x 155mm 16 x 160mm 17 x 165mm 18 x 170mm 19 x 175mm
Hip Fracture Design Features: Forged cobalt chrome approximately twice the fatigue strength of cast CoCr. Interlok finish enhances cement-to-implant bonding. 3 bi-planar taper to promote compressive loading vs. shear of the cement mantle. Duckbill collar stresses medial calcar and helps prevent subsidence. 140 neck angle. Can be cemented or press-fit. If press-fitting, special gold-nitrided Hip Fracture broaches must be used. Sizing is one-to-one. Example: If you template to a 10, ream and broach to a 10. If you are cementing, implant an 8mm stem. If you are press-fitting, implant a 10mm stem. PMMA centering sleeve centralizes stem within the canal. Alliance instrumentation. Interlok and Alliance are registered trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Hip Fracture Hip Fracture Femoral Components Broach PMMA Centering Sleeve 162900 162901 162902 162903 162904 31-473900 31-473901 31-473902 31-473903 31-473904 31-473905 162908 162910 162912 162914 162916 8mm 10mm 12mm 14mm 16mm 18mm
Integral Centralizer* Design Features: Forged cobalt chrome approximately twice the fatigue strength of cast CoCr. Interlok finish enhances cement-to-implant bonding. 3 bi-planar taper to promote compressive loading vs. cylindrical designs. Integrated A/P and medial spacers allow for centralized placement and an even cement mantle. Cobra flare for cement pressurization. Duckbill collar stresses medial calcar and helps prevent subsidence of stem. PMMA distal centralizer for more consistent cement mantle. Alliance instrumentation. 99.3% survivorship at mean follow-up of 7 years (Bankston; Total Joint and Sports Medicine Symposium, 2001). *Also offered in a lateralized version where the Morse taper is shifted 6mm medially. When using the lateralized option, the offset is increased, thereby tightening soft tissues without affecting leg length. Integral, Interlok and Alliance are registered trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Integral Centralizer Integral Femoral Components Distal Stem Positioners Lateralized 12-162609 12-162611 12-162613 12-162615 12-162617 11-162709 11-162711 11-162713 11-162715 11-162717 9 x 125mm 11 x 135mm 13 x 145mm 15 x 155mm 17 x 165mm 162656 162640 162657 162641 162658 162642 162659 162643 162660 162644 162661 162646 9mm 10mm 11mm 12mm 13mm 14mm 15mm 16mm 17mm 18mm 19mm 20mm
Integral X-Series Porous Primary Design Features: Net-forged Ti alloy provides precise and consistent development of hip implants and related instrumentation. Extended level of PPS coating (tuxedo tail) creates a tight circumferential scratch-fit that provides initial stability. 3 bi-planar taper. 140 neck angle (both standard and lateralized). Broad lateral shoulder for rotational stability to promote compressive loading. Porous coated duckbill collar stresses the medial calcar and helps prevent subsidence of the stem. Also offered in a reduced proximal profile (RPP) option to fit the stove pipe femur. Exact RPP broaches (nitrided black) must be used. Use only with Exact Alliance Instrumentation. Integral, Alliance, Exact and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Integral X-Series Porous Primary X170307 X170308 X170309 X170310 X170311 X170312 X170313 X170314 X170315 X170316 X170317 X170318 X170319 X170320 X170321 Lateralized X11-170308 X11-170309 X11-170310 X11-170311 X11-170312 X11-170313 X11-170314 X11-170315 X11-170316 X11-170317 X11-170318 X11-170319 X11-170320 X11-170321 7 x 115mm 8 x 120mm 9 x 125mm 10 x 130mm 11 x 135mm 12 x 140mm 13 x 145mm 14 x 150mm 15 x 155mm 16 x 160mm 17 x 165mm 18 x 170mm 19 x 175mm 20 x 180mm 21 x 185mm
Osteocap rs Design Features: Forged Ti alloy. Circumferential PPS coating on proximal 1/3 and under conical collar. 30 proximal geometry for optimum physiological stress transfer coupled with a 3 bi-planar taper. Distal coronal slot to reduce stem stiffness and minimize distal point loading. Four distal flutes enhance rotational stability. 135 neck angle. rs (Reduced Stiffness). Alliance instrumentation. Must use cylindrical reamers, conical reamers, necks and reduced proximal profile (RPP) broaches. The Osteocap rs is marketed for noncemented use in skeletally mature patients undergoing primary hip replacement surgery as a result of noninflammatory degenerative joint disease. Osteocap rs, Alliance and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
110109 110110 110111 110112 110113 110114 110115 110117 Provisional Number 31-110109 31-110110 31-110111 31-110112 31-110113 31-110114 31-110115 31-110117 Osteocap rs 9 x 145mm 10 x 150mm 11 x 150mm 12 x 155mm 13 x 155mm 14 x 160mm 15 x 160mm 17 x 165mm
Progressive Design Features: Forged Ti alloy. Proximal 40% circumferential PPS coating, while remainder of stem is polished. Bi-planar taper proximal 2/3 of implant. Cylindrical distally with multiple distal splines providing increased rotational stability. 130 neck angle. 10 anteverted neck to aid in replicating normal anatomies. Duckbill collar with porous coating on the bottom of the collar. Distal coronal slot on sizes 11 and above. Alliance instrumentation with combination reamers. Progressive, Alliance and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Right 166314 166316 166318 166320 166322 166324 166326 166328 166330 Left 166315 166317 166319 166321 166323 166325 166327 166329 166331 Progressive 9 x 125mm 10 x 130mm 11 x 135mm 12 x 140mm 13 x 145mm 14 x 150mm 15 x 155mm 16 x 160mm 17 x 165mm
Rx 90 Smooth Design Features: Forged cobalt chrome approximately twice the fatigue strength of cast CoCr. Smooth satin finish (17 Ra). 3 bi-planar taper to promote compressive loading vs. shear of the cement mantle. Reduced medial collar provides optimal calcar support. Integrated PMMA proximal spacers located on the medial, anterior and posterior aspects. Large cement mantle 3.5mm proximal medially, 2.5mm proximal laterally. PMMA distal centralizers are available in 1.5mm (standard) or 2.5mm (large) sizes. 140 neck angle. Available in lateralized option Morse taper is shifted 6mm medially without altering leg length. Alliance instrumentation. The Rx 90 Primary is marketed for use with bone cement in the United States. Rx 90 and Alliance are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Rx 90 Smooth Rx 90 Smooth Femoral Components Rx 90 Smooth Cement Spacers Standard Lateralized 1.5mm 2.5mm 159009 159011 159013 159015 159017 11-159009 11-159011 11-159013 11-159015 11-159017 9 x 125mm 11 x 135mm 13 x 145mm 15 x 155mm 17 x 165mm 149019 149021 149023 149025 149027 149029 149031 149033 149035 149037 9mm 11mm 13mm 15mm 17mm
Balance Design Features: Forged Ti alloy. Proximal 40% PPS coating for enhanced bone ingrowth. 3 bi-planar taper promotes compressive loading. 5 proximal anterior build-up for maximum A/P fill. 5 anteverted neck, right and left specific, aids in replicating normal anatomies. 135 neck angle. Middle 1/3 Interlok finish and distal 1/3 is satin finish. Simple ream only surgical technique. The Balance is marketed for non-cemented use in skeletally mature patients undergoing primary hip replacement surgery as a result of noninflammatory degenerative joint disease. Balance, Interlok and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Balance Provisional Number Provisional Number 180000 180001 180002 180003 180004 180005 180006 180007 180008 180009 180010 180011 180012 180013 180014 180015 180016 180017 180018 180019 180020 180021 180022 180023 31-200013 31-200014 31-200015 31-200016 31-200017 31-200018 31-200019 31-200020 31-200021 31-200022 31-200023 31-200024 31-200025 31-200026 31-200027 31-200028 31-200029 31-200030 31-200031 31-200032 31-200033 31-200034 31-200035 31-200036 7 x 140mm Rt 7 x 140mm Lt 8 x 145mm Rt 8 x 145mm Lt 9 x 150mm Rt 9 x 150mm Lt 10 x 155mm Rt 10 x 155mm Lt 11 x 160mm Rt 11 x 160mm Lt 12 x 165mm Rt 12 x 165mm Lt 13 x 170mm Rt 13 x 170mm Lt 14 x 175mm Rt 14 x 175mm Lt 15 x 180mm Rt 15 x 180mm Lt 16 x 180mm Rt 16 x 180mm Lt 17 x 180mm Rt 17 x 180mm Lt 18 x 180mm Rt 18 x 180mm Lt 170096 170097 170098 170099 Slots in distal portion of implant begin at size 16mm. 31-200040 31-200041 31-200042 31-200043 19 x 180mm Rt 19 x 180mm Lt 20 x 180mm Rt 20 x 180mm Lt
Bio-Moore II Design Features: Forged Ti alloy. Interlok finish enhances cement-to-implant bonding. Type I Morse taper. I-beam design for rotational stability. Incorporates a lateral fin for rotational stability. Offered in solid or fenestrated options. Can press-fit or cement solid components, and can ONLY press-fit fenestrated components. Needs taper inserts for use with Endo II heads (5 neck lengths: -6, -3, Std., +3, and +6mm). Compatible with all Biomet acetabular components. Bio-Moore, Interlok and Biomet are registered trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Bio-Moore II Solid 139202 139203 139204 139205 Fenestrated 139209 139210 139211 10 x 165mm 12 x 165mm 14 x 165mm 16 x 165mm
Mallory-Head Interlok Design Features: Forged cobalt chrome approximately twice the fatigue strength of cast CoCr. Interlok finish on proximal 1/3 of stem and the distal 2/3 of the stem is smooth. 3 bi-planar taper to promote compressive loading vs. cylindrical designs. Duckbill collar anchors the implant to the bone and directs the cement to the distal canal. Distal I-beam channel resists rotational forces. Two 20 ribs located proximally on the anterior and posterior sides force cement medially into compression. PMMA centering sleeve used distally for central alignment in the canal. Mallory-Head cemented instrumentation. The Mallory-Head Interlok is marketed for use with bone cement in the United States. Mallory-Head and Interlok are registered trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Mallory-Head Interlok PMMA Centering Sleeve 105606 105607 105609 105611 105613 105615 5/7 x 135mm 7 x 140mm 9 x 150mm 11 x 160mm 13 x 170mm 15 x 180mm 162907 162909 162911 162913 162915 7mm 9mm 11mm 13mm 15mm
Mallory-Head Porous Primary Design Features: Forged Ti alloy. PPS (Porous Plasma Spray) coating on proximal 1/3 of stem, middle 1/3 of stem is roughened Interlok finish, and distal 1/3 is smooth finish. Dual tapered geometry provides a lateral to medial taper and a 3 included taper from proximal to distal. Proximal finned geometry designed to minimize rotation due to torsional loads. Standard 136 neck angle; lateralized 131 neck angle. Offset option increases proportionately based on stem size (6 8mm of additional offset). Provides quadrilateral fixation via: Lateral fin, anterior fin, posterior fin, and medial contact. HA option over PPS coating. 99.5% survivorship at 11 years (Head, et al.; Orthopedics, 1999). Mallory-Head, Interlok and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Mallory-Head Porous Primary 11-104106 11-104107 11-104108 11-104109 11-104110 11-104111 11-104112 11-104113 11-104114 11-104115 11-104116 21-104117 21-104118 21-104119 Mallory-Head Porous Primary HA 21-104109 21-104110 21-104111 21-104112 21-104113 21-104114 21-104115 21-104116 21-104117 21-104118 21-104119 6 x 135mm 7 x 140mm 8 x 145mm 9 x 150mm 10 x 155mm 11 x 160mm 12 x 165mm 13 x 170mm 14 x 175mm 15 x 180mm 16 x 180mm 17 x 180mm 18 x 180mm 19 x 180mm 11-104209 11-104210 11-104211 11-104212 11-104213 11-104214 11-104215 11-104216 11-104217 Mallory-Head Lateralized Porous Primary HA 21-124309 21-124310 21-124311 21-124312 21-124313 21-124314 21-124315 21-124316 21-124317 9 x 150mm 10 x 155mm 11 x 160mm 12 x 165mm 13 x 170mm 14 x 175mm 15 x 180mm 16 x 180mm 17 x 180mm
Bi-Metric Long Stem Design Features: Forged Ti alloy. Proximal 1/3 of stem PPS coated, Interlok finish distally for enhanced stability. Collar design with 2 anterior bow. Available in 200mm, 250mm and 300mm lengths (all bowed). Alliance instrumentation. The Bi-Metric Revision is marketed for use with bone cement in the United States. Bi-Metric, Interlok, Alliance and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Bi-Metric Long Stem Right 162340 162342 162344 162346 162348 162350 162352 162354 162356 162358 162360 162362 162364 162366 162368 Left 162341 162343 162345 162347 162349 162351 162353 162355 162357 162359 162361 162363 162365 162367 162369 9 x 200mm 11 x 200mm 13 x 200mm 15 x 200mm 17 x 200mm 9 x 250mm 11 x 250mm 13 x 250mm 15 x 250mm 17 x 250mm 9 x 300mm 11 x 300mm 13 x 300mm 15 x 300mm 17 x 300mm
Integral 180 Design Features: Forged Ti alloy. 70% PPS coated. 3 bi-planar taper proximally to promote compressive loading, cylindrical after 100mm. Distal coronal slot to reduce thigh pain. Porous coated duckbill collar stresses the calcar and prevents subsidence. 140 neck angle. Can be used as a primary or a short revision stem. Also offered in a reduced proximal profile (RPP) option to fit the stove pipe femur (RPP broaches must be used). Alliance instrumentation. Integral, Alliance and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Integral 180 166010 166011 166012 166013 166014 166015 166016 166017 166018 166019 Reduced Proximal Profile 11-166011 11-166012 11-166013 11-166014 11-166015 11-166016 11-166017 11-166018 11-166019 10 x 180mm 11 x 180mm 12 x 180mm 13 x 180mm 14 x 180mm 15 x 180mm 16 x 180mm 17 x 180mm 18 x 180mm 19 x 180mm
Mallory-Head Interlocking Calcar Design Features: Forged Ti alloy. Titanium PPS coating proximal 40% of stem for enhanced bone ingrowth. Proximal calcar loading implant with distal interlocking screws for added fixation. Distal targeting device for accurate screw placement. Bolt/claw for reattachment of trochanter. 45mm resection level only. Useful in most severe proximal femoral bone loss. Used in proximal femoral allograft procedures for additional rotational stability. Stem length 260mm bowed, with sizes 13 19mm in 2mm increments. Utilizes 5.0mm Kaesman screws. Mallory-Head and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Mallory-Head Interlocking Calcar Right 154781 154783 154785 154787 Left 154780 154782 154784 154786 13 x 45 x 260mm 15 x 45 x 260mm 17 x 45 x 260mm 19 x 45 x 260mm
Mallory-Head Long Stem Design Features: Forged Ti alloy. Porous coated on proximal 1/3, with distal 2/3 Interlok finish over anti-rotational grooves. Features the same proximal finned geometry as the primary porous implants. Lengths of 250 and 300mm bowed stems needed lengths required to bridge distal cortical defects and provide increased stability and fixation. Used in revisions where there is minor reconstruction to be done proximally with intact calcar and very little osteolysis. Mallory-Head instrumentation. The Mallory-Head Revision is marketed for use with bone cement in the United States. Mallory-Head and Interlok are registered trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Mallory-Head Long Stem Right 104810 104812 104814 104816 104818 104910 104912 104914 104916 104918 Left 104809 104811 104813 104815 104817 104909 104911 104913 104915 104917 9 x 250mm 11 x 250mm 13 x 250mm 15 x 250mm 17 x 250mm 9 x 300mm 11 x 300mm 13 x 300mm 15 x 300mm 17 x 300mm
Mallory-Head Modular Calcar Proximals Design Features: Trochanteric bolts/claws/plates provide additional stability. HA option over PPS coating. Used for large defects in the calcar region with severe bone loss. Modularity allows customization via Morse taper and segmental locking screw attachment. Offers 34, 45 and 55mm resection levels (A through E bodies) to compensate for bone loss in the proximal/medial portion of the femur. Version adjustment capability with Sundial. Roller-hardened technology provides 50% stronger taper than competitive tapers. 1 1 Data on file at Biomet. Mallory-Head and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Mallory-Head Modular Calcar Proximals Mallory-Head Modular Metaphyseal Segment 108110 108112 108115 108117 108119 108130 108132 108135 108137 108139 108150 108152 108155 108157 108159 108710 108730 HA 21-108110 21-108112 21-108115 21-108117 21-108119 21-108130 21-108132 21-108135 21-108137 21-108139 21-108150 21-108152 21-108155 21-108157 21-108159 Size 34A 34B 34C 34D 34E 45A 45B 45C 45D 45E 55A 55B 55C 55D 55E 65A 75A Troch Bolt/Plates Part No. 11-105020 11-105021 11-104911 11-104914 11-104912 11-104915 11-104913 Lat Claw Connector Part No. CoCr Trochanteric Claw Medium Large 11-105005 11-105006 11-105007 11-105008 11-105009 Trochanter Bolt w/poly Plug Oblong (Mod Calcar) 13-104756 40 50mm 45 55mm 50 60mm 55 65mm 60 70mm
Mallory-Head Modular Calcar Distals Design Features: Used for large defects in the calcar region with severe bone loss. Modularity allows customization via Morse taper and segmental locking screw attachment. Several distal lengths available to bridge distal defects (75 300mm). Coronal slot to reduce thigh pain. Impact distal stems may be utilized with the system. HA option over PPS coating (220mm and 250mm options only). Roller-hardened technology provides 50% stronger taper than competitive tapers. 1 Various plasma spray porous coating levels available: 220mm (40% to 80%), 250mm (80%), and 300mm (60%). Version adjustment capability with Sundial. Macro sizes up to 23mm and stem lengths of 350mm. 1 Data on file at Biomet. Mallory-Head, Impact and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Mallory-Head Modular Calcar Distals STS Diaphyseal Segments 200mm 240mm Size 11-108740 11-108741 11-108742 11-108743 11-108744 11-108745 11-108746 11-108750 11-108751 11-108752 11-108753 11-108754 11-108755 11-108756 14mm 15mm 16mm 17mm 18mm 19mm 20mm 165mm Diaphyseal Segments 100% Coated Straight Size 11-135160 11-135161 11-135162 11-135163 11-135164 11-135165 11-135166 11-135167 11-135168 11-135169 11-135170 11mm 12mm 13mm 14mm 15mm 16mm 17mm 18mm 19mm 20mm 21mm 220mm 11-108451 11-108453 11-108455 11-108457 11-108459 11-108251 11-108253 11-108255 11-108257 11-108259 Mallory-Head Modular Diaphyseal Segments w/locking Screw 250mm 11-108271 11-108273 11-108275 11-108277 11-108279 300mm 11-108091 11-108093 11-108095 11-108097 11-108099 HA 220mm 21-108251 21-108253 21-108255 21-108257 21-108259 HA 250mm 21-108271 21-108273 21-108275 21-108277 21-108279 Size 11mm 13mm 15mm 17mm 19mm 11mm 13mm 15mm 17mm 19mm 11mm 13mm 15mm 17mm 19mm % Porous 40% Porous 40% Porous 40% Porous 40% Porous 40% Porous 80% Porous 80% Porous 80% Porous 80% Porous 80% Porous 60% Porous 60% Porous 60% Porous 60% Porous 60% Porous Spiralock Segmental Locking Screw 112000
Mallory-Head One-Piece Calcar Design Features: Forged Ti alloy. PPS coated on proximal 40% of stem. Porous coated keel allows transfer of rotational load to the calcar region. Has 2mm wire passage holes for reattachment of trochanter. Can use with trochanteric bolts/plates/claws. 34, 45 and 55mm resection levels offered. Lengths include 170 (straight) and 220/260mm (bowed). The long stems have a distal anterior bow to provide better stability and more closely match the femur. 99.2% survivorship up to 13 years follow-up. Only 1.1% femoral complications out of 1,179 revision hips (Head, et al.; AAHKS Meeting, 2001). Used clinically since 1987. The Mallory-Head Calcar is marketed for use with bone cement in the United States. Mallory-Head and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Mallory-Head One-Piece Calcar 11-104902 11-104903 11-104904 11-104905 Right 11-104947 11-104949 11-104951 11-104953 11-104955 11-104977 11-104957 11-104961 11-104965 11-104969 11-104973 11-104984 11-104959 11-104963 11-104967 11-104971 11-104975 11-104986 Left 11-104948 11-104950 11-104952 11-104954 11-104956 11-104978 11-104958 11-104962 11-104966 11-104970 11-104974 11-104985 11-104960 11-104964 11-104968 11-104972 11-104976 11-104987 Resection Level 34mm 34mm 34mm 34mm Resection Level 34mm 34mm 34mm 34mm 34mm 34mm 45mm 45mm 45mm 45mm 45mm 45mm 55mm 55mm 55mm 55mm 55mm 55mm Straight Stem 9 x 170mm 11 x 170mm 13 x 170mm 15 x 170mm 9 x 220mm 11 x 220mm 13 x 220mm 15 x 220mm 17 x 220mm 19 x 220mm 9 x 220mm 11 x 220mm 13 x 220mm 15 x 220mm 17 x 220mm 19 x 220mm 9 x 220mm 11 x 220mm 13 x 220mm 15 x 220mm 17 x 220mm 19 x 220mm 11-105020 11-105021 Troch Bolt/Plates Part No. Lat. Claw Connector Part No. 11-104911 11-104914 11-104912 11-104915 11-104913 CoCr Trochanteric Claws Medium Large Trochanter Bolt w/poly Plug Round 11-104910 11-105005 11-105006 11-105007 11-105008 11-105009 40 50mm 45 55mm 50 60mm 55 65mm 60 70mm
Modular Reach Revision Design Features: Forged Ti alloy. Titanium PPS coating for enhanced bone ingrowth. 135 neck angle. Bi-planar taper geometry. Collar and collarless proximal body. Modular system allows precise fit and fill. Six proximal body sizes. Fully interchangeable with Modular Calcar System (used with all Mallory-Head modular distal stems including STS distals). HA option over porous plasma spray. Mallory-Head, Reach and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Modular Reach Revision Collared Collarless HA Collared HA Collarless 108391 108393 108395 108397 108399 108401 108291 108293 108295 108297 108299 108301 Proximal Size 1 Proximal Size 2 Proximal Size 3 Proximal Size 4 Proximal Size 5 Proximal Size 6 21-108391 21-108393 21-108395 21-108397 21-108399 21-108291 21-108293 21-108295 21-108297 21-108299 Proximal Size 1 Proximal Size 2 Proximal Size 3 Proximal Size 4 Proximal Size 5
PLR Splined Design Features: Forged Ti alloy. Unique spline geometry reduces stem stiffness and risk of subsidence. Anatomic neck angle 135 for added offset. One piece 270mm straight tapered stem from neck resection. Lateral holes for soft tissue reattachment. 1.5 taper extends the stemʼs entire length. Spline depth 1.5mm 2.5mm provides rotational stability. 30 grit-blast surface finish for bone ingrowth. Simple, precise instruments and trials. PLR is a trademark of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
PLR Splined 11-158314 11-158315 11-158316 11-158317 11-158318 11-158319 11-158320 11-158321 11-158322 11-158323 11-158324 14 x 270mm 15 x 270mm 16 x 270mm 17 x 270mm 18 x 270mm 19 x 270mm 20 x 270mm 21 x 270mm 22 x 270mm 23 x 270mm 24 x 270mm
Reach Revision Design Features: Forged Ti alloy. Stem fully coated 100% PPS coating. 3 bi-planar taper proximally to promote compressive loading, cylindrical after 100mm. Neck extended 6mm to help restore offset. Duckbill collar stresses the medial calcar and helps prevent subsidence of the stem. Stem size includes distal porous coating Example: 13mm stem size = 13mm distal diameter with porous coating. Stem lengths: 200mm straight, 200mm bowed and 250mm bowed. Ream = 0.5mm 1mm overream distal. Reach and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Reach Revision Reach 200mm Straight 100% Coated Reach 200mm Bowed 100% Coated Right Left 12-162111 12-162113 12-162115 12-162117 12-162119 11 x 200mm 13 x 200mm 15 x 200mm 17 x 200mm 19 x 200mm 162111 162113 162115 162117 162119 162112 162114 162116 162118 162120 11 x 200mm 13 x 200mm 15 x 200mm 17 x 200mm 19 x 200mm Reach 250mm Bowed 100% Coated Right 11-162111 11-162113 11-162115 11-162117 11-162119 Left 11-162112 11-162114 11-162116 11-162118 11-162120 11 x 200mm 13 x 200mm 15 x 200mm 17 x 200mm 19 x 200mm
Rx 90 Revision Design Features: Cobalt chrome. Proximal 40% Interlok finish, smooth distally. 3 bi-planar taper proximally to promote compressive loading cylindrical after 100mm. Duckbill collar stresses the medial calcar and helps prevent subsidence of the stem. Lateral wire holes provide for reattachment of the trochanter. Available in 200 and 250mm lengths (bowed). Alliance instrumentation. The Rx 90 Revision is marketed for use with bone cement in the United States. Rx 90, Interlok and Alliance are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Rx 90 Revision Right 129113 129115 129117 129119 129123 129125 129127 129129 Left 129114 129116 129118 129120 129124 129126 129128 129130 13 x 200mm 15 x 200mm 17 x 200mm 19 x 200mm 13 x 250mm 15 x 250mm 17 x 250mm 19 x 250mm
Stanmore Design Features: Forged cobalt chrome approximately twice the fatigue strength of cast CoCr. Smooth satin finish (17 Ra). Unchanged design with over 30 years of clinical use. Small collar for cement pressurization. 130 neck angle. Available in standard (increased offset = 8 9mm) and straight options. Slot in top of trunion allows for rotational control during insertion. Simple starter ream and fully toothed broach surgical technique. 92% survivorship at 22 years (Deutman, JBJS 2000). The Stanmore is marketed for use with bone cement in the United States. Stanmore is a trademark of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Stanmore Standard Stem 12-164241 12-164242 12-164243 12-164244 12-164245 Straight Stem 12-164251 12-164252 12-164253 12-164254 12-164255 Size Size 1 Size 2 Size 3 Size 4 Size 5 8 x 123mm 10 x 132mm 12 x 140mm 14 x 149mm 16 x 158mm Stanmore PMMA Distal Stem Positioners 164236 164237 164238 164239 164240 Size 1 Size 2 Size 3 Size 4 Size 5
Taperloc Design Features: Forged Ti alloy. Proximal 50% PPS coated. Neck angle 138. Available in a lateralized version post is shifted 7.6mm medially so leg length is not affected, but tissues will be tightened. Flat tapered stem. HA option over porous plasma spray. Reduced distal option (Exact reduced distal rasps/provisionals are recommended). Simple starter reamer and fully toothed broach surgical technique. 99.6% survivorship at 12 year follow-up out of 4,750 patients (Rothman; Crucial Decisions in TJR and Sports Medicine, Bermuda, 1998). The Taperloc is marketed for non-cemented use in skeletally mature patients undergoing primary hip replacement surgery as a result of noninflammatory degenerative joint disease. Taperloc and PPS are trademarks of Biomet, Inc. P.O. Box 587, Warsaw, IN 46581-0587 574.267.6639 2003 Biomet, Inc. All Rights Reserved web site: www.biomet.com email: biomet@biomet.com Form No. Y-BMT-812/051503/H
Taperloc Modular Porous Taperloc Hip HA Taperloc Hip 103202 103203 103204 103205 103206 103207 103208 103209 103210 103211 103212 Lateralized 11-103202 11-103203 11-103204 11-103205 11-103206 11-103207 11-103208 11-103209 11-103210 11-103211 11-103212 7.5 x 135mm 9.0 x 137mm 10.0 x 140mm 11.0 x 142mm 12.5 x 145mm 13.5 x 147mm 15.0 x 150mm 17.5 x 155mm 20.0 x 160mm 22.5 x 165mm 25.0 x 170mm 21-103202 21-103203 21-103204 21-103205 21-103206 21-103207 21-103208 21-103209 21-103210 21-103211 21-103212 Lateralized 21-123202 21-123203 21-123204 21-123205 21-123206 21-123207 21-123208 21-123209 21-123210 21-123211 21-123212 7.5 x 135mm 9.0 x 137mm 10.0 x 140mm 11.0 x 142mm 12.5 x 145mm 13.5 x 147mm 15.0 x 150mm 17.5 x 155mm 20.0 x 160mm 22.5 x 165mm 25.0 x 170mm Reduced Distal Taperloc Hip 12-103206 12-103207 12-103208 12-103209 12-103210 12-103211 12-103212 Lateralized 13-103206 13-103207 13-103208 13-103209 13-103210 13-103211 13-103212 12.5 x 145mm 13.5 x 147mm 15.0 x 150mm 17.5 x 155mm 20.0 x 160mm 22.5 x 165mm 25.0 x 170mm