Peening Technologies of Georgia s Non Destructive department provides a wide range of NDT processes to fit your needs. Our highly trained level II and level III inspectors have close to 20 years, hands on, experience in a wide variety of industries and disciplines. All of our personnel are qualified and certified in accordance with SNT-TC-1A and NAS-410 requirements and prepared to bring nothing but the best in quality and customer satisfaction to your job every time. Need quality inspections at high production? No problem. Our state of the art NDT lab is capable of processing thousands of parts per day. We offer one of the largest fluorescent penetrant lines in the South East and we have 3 Magnaflux benches capable of inspecting parts up to 52 inches in length and up to 10,000 amperes. If it s Aircraft quality or general services, Peening Technologies NDT offers the highest quality at economical prices right for any client. NDT METHODS Visual Testing (VT) Borescope, Videoscopes, Aircraft windshield inspections, etc. o CWI inspectors on staff for your welding and structural needs. Magnetic Particle Testing (MT) Fluorescent and Visible Particles. AC and DC methods. Direct and Induced magnetism. No part to big or too small. Liquid Dye Penetrant Inspection (PT) - Fluorescent and visible penetrants at any sensitivity. Eddy Current Testing (ET) Bolt holes, composites, near edge defects. Ultrasonic Testing (UT)- Shear wave, Phased array, thickness, PMI, Etc. Radiographic Testing (RT)- Digital and traditional films X-ray and Gamma. Additional Services Include Positive Material Analysis Part Marking / Pin Stamping New Part Technique Development
Magnetic Particle Inspections Magnetic Particle is a quick effective method of detecting flaws in ferromagnetic materials at or just below the surface. Peening technologies offers a wide range of Magnetic Particle Inspections to satisfy the requirements of any job. We have 3 wet stationary benches for inspections of parts up to 52 inches in length. Larger parts can be inspected with our portable cable wrap unit or electromagnetic yokes. Wet fluorescent, wet nonfluorescent, and dry powders are available to locate the smallest of discontinuities in any part. Services offered in our lab or your facility. No job is too big or too small. 5,000 Ampere Unit Wet Nonfluorescent 10,000 Ampere Unit Wet Fluorescent Electromagnetic Yoke and Cable wrap
Radiographic Inspections Peening Technologies offers conventional and computed Radiographic Testing with traditional film or phosphoric imaging plates. The computed radiographic method produces ultra-high sensitivity radiographs that can be kept on your computer for long term storage or image sharing. Our highly trained radiographers are versed, trained and qualified in both traditional and computed radiographic testing methods. We will settle for nothing less than the highest quality and safest method for our clients. We offer both X-Ray and Gamma radiography. We can use X-Ray tube for high traffic work areas so other work will not be halted for radiographic testing thus eliminating traditional shot windows or late night shoots. Computed Radiography Traditional Film
Liquid Dye Penetrant Inspection Liquid penetrant testing reveals the smallest flaws open to the surface in nearly any type of material. Plastics, composite, or metallic materials can all be inspected using this method. Peening technologies has one of the largest fluorescent penetrant lines in the south east. With 220 gallon tanks capable of handling parts of nearly any size or geometry. Large parts can be inspected at high productivity with the greatest of accuracy. Need inspections at your facility? Not a problem. We can dispatch our services to your location with our highly trained technicians to provide both visible and fluorescent methods. Any Sensitivity any part. Fluorescent Penetrant Line
Ultrasonic Inspections We offer precise flaw detection with the use of Ultrasonic Testing Shearwave or Phased Array inspections or thickness testing. Peening Technologies has state of the art equipment and AWS certified phased array technicians on staff ready to provide these services anywhere. If it s your facility or ours, our level II and level III UT technicians provide nothing but the best in down home southern hospitality and highly trained hands-on experience to provide our clients trusted reliable results every time. Phased Array Inspections Shearwave Inspections Thickness Inspections
Eddy Current Inspection Electromagnetic Current testing, or Eddy Current Testing, can locate changes in conductivity in any conductive material thus providing a nearly flawless representation of a discontinuity in the material. Our Highly trained technicians are experienced and thorough. We provide bolt hole inspections, near edge inspections, flaw and conductivity inspections with state of the art equipment capable of providing computed documentation of the inspection. From aircraft to compressor blades we offer the best in ET inspections. Eddy Current Testing Aircraft Compressor Blades Bolt Hole Scans Near Edge Scans Changes in conductivity Material analysis Changes in conductivity Near Edge Scans
Additional Services Peening Technologies of Georgia is proud to announce our Non Destructive Testing Services to our current and prospective clients. We would also like to mention some of our additional services. Positive Material Verification and Analysis With the use of our Nitron Analyzer we are able to measure with extreme accuracy the exact element content of any material. A vital tool when dealing with heat treated super alloys. Parts Marking / Pin Stamping When our clients need to sort parts and have positive, permanent, and nondetrimental identification. We have the tool. Our Pin Stamping Machine can permanently scribe identification to any part.