An Electrically Actuated Pin-Puller for Space Application using Nickel- Titanium Memory Alloy Peter M. Cipollo, Brendan S. Surrusco Advisor: Dr. Sven G. Bilén The Pennsylvania State University Frank J. Redd Student Scholarship Competition Small Satellite Conference August 11, 2004 Logan, Utah
LionSat Program Objectives Mission Statement The LionSat mission will investigate the local ambient and perturbed plasma environments surrounding a small satellite in the Earth s ionosphere. LionSat will measure the ambient plasma environment and the satellite s ram and wake regions using a novel hybrid plasma probe instrument. LionSat will test a miniature RF ion thruster system that will augment the satellite spin, which is necessary for mapping the plasma environment surrounding the satellite. Technology Demonstration LionSat will demonstrate the Hybrid Plasma Probe as a plasma diagnostic instrument. LionSat will also test in situ a miniature RF Ion Thruster as a satellite spin control device. Science Mission Goals Primary Objectives: P1. To map the ram and wake plasma structure surrounding a small satellite P2. To collect data on ionospheric plasma in a variety of geophysically interesting locations in low Earth orbit P3. To test, on orbit, a miniature RF ion thruster Secondary Objective: S1. To test IP communications for uplink and downlink to a spacecraft in low Earth orbit
Spacecraft Technical Data Dimensions Diameter: 18.25 inches Length: 18.5 inches Shape: Octagon Mass Budget 30 kg maximum Power Budget 26.2 W 12 20 V bus depending on load Cost $100K from Air Force, seed money
Mission Timeline
Hybrid Plasma Probes (HPP) Boom length: 17 in. Linear deployment via winch Motor Cable Tensioner Boom Boom Guide
HPP Inhibit Requirement Requirement Functions Resulting in Critical Hazards. A function whose inadvertent operation could result in a critical hazard must be controlled by two independent inhibits, whenever the hazard potential exists. NSTS 1700.7B, section 201.2 Solution a low cost, electrically actuated pin-puller that makes use of Nickel-Titanium (NiTi) memory alloy to be used as part of the boom deployment inhibit system.
Pin-Puller Criteria Low Mass - strict mass budget < 200 g Low Cost - COTS hardware where possible Reusable - must be able to cycle multiple times to reduce testing costs Remote Reset - not practical to disassemble satellite to reset device 12-V unregulated supply for operation, current draw 500 ma No magnetic parts No hazardous materials
Commercial Possibilities None could be found that meet all the criteria
NiTi Pin-Puller Design Low force linear actuator using NiTi shape memory alloy Low power Automatically resettable Reusable Nonmagnetic Nonhazardous Light weight Inexpensive
NiTi Pin-Puller Design Issues Anodized aluminum construction provides electrical insulation for NiTi wire Ø 0.004" NiTi shape memory alloy actuator provides the required displacements and forces Steel bias/reset spring keeps the pin engaged at >75 g acceleration Capacitive discharge circuit reduces the requirements on the power system 25 g mass (not including electronics) 0.125" stroke ensures pin is engaged 3.5" overall length 0.5" largest diameter
NiTi Mechanical Response Mechanical Response of Ø0.004 NiTi Actuator Wire with Steel Bias Spring Load [lbf] 3.0 2.9 2.8 2.7 2.6 2.5 2.4 2.3 2.2 NiTi, Austenite 2.1 NiTi, Martensite 2.0 Steel Spring 1.9 1.8 1.7 1.6 Austenitic Equilibrium 1.5 1.4 Martensitic Equilibrium 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 Stroke 0.3 0.2 0.1 0.0 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 Deflection [in]
NiTi Pin-Puller Charging Circuit Design Issues Charging Current 500-mA peak current draw at 5 V Capacitor is fully charged in <60 s 0.8-F capacitor chosen for energy capacity/favorable discharge time constant 10-Ω resistor in series with capacitor reduces peak current draw without dropping excessive power Current [A] 0.600 0.500 0.400 0.300 0.200 0.100 0.000 0 10 20 30 40 50 60 Time [s] Capacitor Voltage (Charging) 5.5 5 4.5 4 Voltage [V] 3.5 3 2.5 2 1.5 1 0.5 0 0 10 20 30 40 50 60 Time [s]
NiTi Pin-Puller Capacitive Discharge Circuit Design Issues Discharge Current 30-Ω power resistor in series with capacitor to achieve time constant 0.35-W maximum power dissipation in resistor NiTi wire transitions from -55 C to 90 C in 38 s, holds above 90 C for minutes Discharge controlled by the flight computer Allows precise coordination of components in the deployment system Current [A] Power Dissipated in Resistor During Discharge [W] 0.120 0.100 0.080 0.060 0.040 0.020 0.000 0.40 0.30 0.20 0.10 0 20 40 60 80 100 120 Time [s] Dissipated Power 0.00 0.0 20.0 40.0 60.0 80.0 100.0 120.0 Time [s]
NiTi Pin-Puller Status Work Completed NiTi wire obtained for experimentation Alpha prototype designed and fabricated Testing showed initial bias spring was too stiff and NiTi wire failed mechanically Steel spring selected for LionSat application Equipment developed for conditioning of NiTi wires Beta prototype designed Beta prototype fabricated Testing Regimen Apply 200 ma to NiTi wire at 5% strain with bench supply Test pin-puller with capacitive discharge circuit Test pin-puller in thermal vacuum
Conclusion Inexpensive pin puller designed for LionSat mission Meets all LionSat requirements and NS-3 safety requirements Simple design should be applicable to other nanosat missions