bliss 1 Sonic Bliss Happiness sounds just like this Happiness sounds just like this. bliss Fitting Guide

Transcription

1 bliss Sonic Bliss Happiness sounds just like this Happiness sounds just like this. bliss Fitting Guide

2

3 Sonic Bliss Happiness sounds just like this 3 Table of Contents Introduction Bliss BTE Overview 4 Bliss minibte Overview 5 Bliss Custom Instruments Overview 6 Acoustic Performance 8 Fitting ranges 8 Bliss BTE and minibte Hearing Instruments 9 Acoustic options 9 Thin Tube lengths 9 Determining the proper Thin Tube length 9 Installing right and left instrument markers on Bliss BTE 0 Installing right and left instrument markers on Bliss minibte 0 Attaching and removing the Earhook or Thin Tube Adapter Attaching and removing the Thin Tube Changing Thin Tube Domes Bliss BTE DAI 3 Attaching the DAI Boot minibte 4 Removing the DAI Boot minibte 4 Bliss Custom Hearing Instruments 5 Replacing the ProWax 5 Replacing the microphone protection cap 6 Fitting a Bliss IIC 8 Programming Bliss with EXPRESSfit 0 Attaching programming cables 0 Programming Bliss Using the EXPRESSfit Fitting Software Ordering Information 30 This document introduces you to the Bliss hearing instrument family. Here you will find step-by-step instructions on everything from exchanging the Thin Tubes and Earhooks, to fine-tuning adjustments in the EXPRESSfit fitting software. For additional information, please contact your local Sonic Customer Care Representative.

4 4 Sonic Bliss Happiness sounds just like this Bliss BTE Overview Thin Tube and Dome Front microphone Thin Tube Adapter 3 Rear microphone 4 Thin Tube 5 Program Button 6 Battery door grip 7 Battery door 8 Sound outlet 9 Dome 0 Volume Control Retention lock DAI Port Earhook and Earmold Front microphone Earhook 3 Rear microphone 4 Program Button 5 Earmold tubing 6 Battery door grip 7 Battery door 8 Volume Control 9 Earmold 0 DAI Port 0

5 Sonic Bliss Happiness sounds just like this 5 Bliss minibte Overview Thin Tube and Dome Front microphone Thin Tube Adapter 3 Rear microphone 4 Thin Tube 5 Battery door 6 Sound outlet 7 Program Button 8 Dome 9 Tamper-resistant lock 0 Retention lock DAI Port Earhook and Earmold Front microphone Earhook 3 Rear microphone 4 Earmold tubing 5 Battery door 6 Program Button 7 Tamper-resistant lock 8 Earmold 9 DAI Port 9

6 6 Sonic Bliss Happiness sounds just like this Bliss Custom Instruments Overview ITEPDW and ITED Sound outlet with wax protection Canal 3 Microphone openings with O-Cap filter 4 Battery door 5 Air vent 6 Program Button Note! Bliss ITEPDW and ITED can be built with an optional Program Button. Bliss ITED can be built with an optional Volume Control. ITCPDW and ITCD Sound outlet with wax protection Canal 3 Program Button 4 Battery door 5 Microphone openings with O-Cap filter 6 Air vent Note! Bliss ITCPDW and ITCD can be built with an optional Program Button. Bliss ITCD can be built with an optional Volume Control.

7 Sonic Bliss Happiness sounds just like this 7 CICP and CIC Sound outlet with wax protection Microphone opening with T-Cap filter 3 Canal 4 Battery door 5 Removal cord 6 Air vent Note! Bliss CICP can be built with an optional Program Button. IIC (Bliss 00 only) Sound outlet with wax protection Microphone opening with T-Cap filter 3 Canal 4 Battery door 5 Removal cord 6 Air vent

8 8 Sonic Bliss Happiness sounds just like this Acoustic Performance Fitting ranges The fitting ranges below will help you select the appropriate hearing instrument model and acoustic configuration for your patient s specific hearing needs. Fitting Range BTE minibte Frequency in Hertz (Hz) Fitting Range ITEPDW Frequency in Hertz (Hz) Fitting Range ITCPDW Frequency in Hertz (Hz) Hearing Level in decibels (db) Hearing Level in decibels (db) 8000 Fitting Range ITED ITCD Frequency in Hertz (Hz) Hearing Level in decibels (db) Hearing Level in decibels (db) Fitting Range CICP Frequency in Hertz (Hz) Fitting Range CIC IIC Frequency in Hertz (Hz) Hearing Level in decibels (db) Hearing Level in decibels (db)

9 Sonic Bliss Happiness sounds just like this 9 Bliss BTE and minibte Hearing Instruments Acoustic options All Bliss BTE and minibte instruments are available with either a conventional Earhook or Thin Tube with Adapter and Dome system. Thin Tube Domes Custom Fit Conventional Earhook Thin Tube 0.9 mm.3 mm 6 mm (XS) 8 mm (S) 0 mm (M) mm (L) Open Dome Tulip Dome Dome, Large Vent Dome, Small Vent Power Dome Various Custom Molds available Thin Tube lengths To ensure a secure fitting with maximum patient comfort, the proper Thin Tube length should be selected for each patient before fitting a Bliss BTE or minibte. Sonic Thin Tubes come in four different lengths, and a red (Right) or blue (Left) marker on the Thin Tube identifies the orientation. Length Size Code XShort 0 Short Medium Long 3 Determining the proper Thin Tube length To determine which Thin Tube length is most appropriate for your patient, use the fitting tool from your Sonic BTE Dispensing Kit. 0 3 Note! Right and left markings on the fitting tool indicate which hand to use and which ear to measure. Four sightlines (0---3) indicate the proper tubing length, according to the table above.

10 0 Sonic Bliss Happiness sounds just like this Installing right and left instrument markers on Bliss BTE Locate the space inside the battery compartment which shows the receptacle for the right and left marker. Line up the end of the red (Right) or blue (Left) marker and slide the tip into the slot until it firmly fits as shown. 3 Twist and break off the long post of the marker tool, ensuring that the marker remains in position. 3 4 Installing right and left instrument markers on Bliss minibte Locate the space on the back of the instrument which shows the receptacle for the right and left marker. Insert the end of the red (Right) or blue (Left) marker into the slot until it firmly fits as shown. 3 Twist and break off the long post of the marker tool, ensuring that the marker remains in the instrument s opening. 3

11 Sonic Bliss Happiness sounds just like this Attaching and removing the Earhook or Thin Tube Adapter Remove the Earhook or Thin Tube Adapter from the hearing instrument by unscrewing it (counter-clockwise). Replace the Earhook or Thin Tube Adapter with the desired part. 3 To attach either the Earhook or Thin Tube Adapter, screw it (clockwise) onto the hearing instrument. 3 3 Note! Be careful not to over-rotate (more than 3 full rotations) the Earhook or Thin Tube Adapter. The BTE Thin Tube Adapter may have a small space between it and the casing, so do not over-rotate.

12 Sonic Bliss Happiness sounds just like this Attaching and removing the Thin Tube If the Thin Tube becomes discolored, stiff or brittle, it should be replaced. Pull firmly to remove the old Thin Tube. Hold the instrument by the Thin Tube Adapter and grasp the Thin Tube close to the threaded connector. 3 Attach the new Thin Tube by pushing it firmly into the Thin Tube Adapter. Changing Thin Tube Domes The soft Domes are a disposable part. The patient should be supplied with spare Domes and shown how to change them. Pull the used Dome off the Thin Tube and discard. With clean hands, firmly push a new Dome onto the Thin Tube as far as it will go. Note! If the Dome is not pushed all the way onto the Thin Tube, it could fall off into the ear canal.

13 Sonic Bliss Happiness sounds just like this 3 Bliss BTE DAI Locate the DAI pins at the bottom of the hearing instrument. Insert the DAI/Euro Plug or FM Receiver of the assistive listening device into this area.

14 4 Sonic Bliss Happiness sounds just like this Attaching the DAI Boot minibte Slip the DAI Boot over the minibte. When it is fully seated you will feel it click into place. Insert the DAI/Euro Plug or FM Receiver of the assistive listening device into the DAI Boot. Removing the DAI Boot minibte Pull the DAI/Euro Plug or FM Receiver out of the DAI Boot. Grasp the DAI Boot as shown. Pull the minibte up and out of the Boot with your other hand. A slight twisting motion will help free the DAI Boot from the minibte.

15 Sonic Bliss Happiness sounds just like this 5 Bliss Custom Hearing Instruments Replacing the ProWax All Bliss custom models are supplied with the ProWax system. Take a new removal tool from the package. Insert the removal prong of the tool into the instrument s existing ProWax and extract the old ProWax. 3 Insert the new ProWax into the instrument and pull out the removal tool. 4 Discard the removal tool and old ProWax. 3 Note! Bliss custom instruments must be used with the ProWax system. Using other wax protection systems could damage the instrument.

16 6 Sonic Bliss Happiness sounds just like this Replacing the microphone protection cap All Bliss custom models are supplied with either the T-Cap or O-Cap for microphone protection. O-Cap filter for ITCD, ITCPDW, ITED, and ITEPDW The tool has two ends, one for removal of the O-Cap (A) and one with the new O-Cap attached (B). A B Using the removal end (A), insert it into the opening of the used O-Cap and pull it out slowly. Keep the stick straight. Using the other end of the tool (B), insert the new O-Cap into the opening and gently remove the stick. 3 Discard the tool and the used O-Cap filter. A A B

17 Sonic Bliss Happiness sounds just like this 7 T-Cap filter for IIC, CIC, and CICP The tool has two ends, one for removal of the T-Cap (A) and one with the new T-Cap attached (B). A B Using the removal end (A), place it under the T-Cap edge, and push it under the top edge of the used T-Cap. Lift the used T-Cap up and out. 3 Using the other end of the tool (B), insert the new T-Cap into the opening and slightly twist the handle so that the new T-Cap is free. 4 Discard the tool and the used T-Cap filter. A A B 3 0

18 8 Sonic Bliss Happiness sounds just like this Fitting a Bliss IIC The IIC hearing instrument is designed to sit deep in the canal after the first bend. Candidacy depends on the patient s ear canal anatomy. In order to determine if an IIC is possible for your patient, follow the fitting guidelines and illustrations below. a b c b a c A Impression evaluation The candidacy evaluation for an IIC hearing instrument requires a quality ear impression that extends beyond the second bend of the ear canal. The size and fit of the IIC is determined by the ear impression. Use the ear impression tool to determine if the size and shape of the ear canal are appropriate for an IIC. a b c b a c B The IIC hearing instrument can be built with the microphone on the side (A) or on the top (B) of the faceplate. The ear impression tool can be used to determine which configuration is most suitable for the given ear impression. Using the ear impression tool a Canal length The length of the canal determines if there is enough room between the tip of the instrument and the faceplate. To determine if the canal length is sufficient, use the red line and measure from the tip of the ear impression to the first () bend. In order to make the IIC invisible, the edge of the tool should not reach the first bend. Ok a Not ok

19 Sonic Bliss Happiness sounds just like this 9 Canal height The height of the canal determines if there is enough space for the IIC to pass through the canal to the final ear canal placement. The height of the ear impression measured at a point between the first () and second () bends must be larger than the pink line on the ear impression tool. b Ok b Not ok 3 Canal width The width of the canal determines if the faceplate will fit past the first bend. The width of the ear impression measured at a point after the first () bend must be greater than the gray line on the ear impression tool. The canal should be wider than the notch and not fit within the notch. c Ok c c Not ok 4 Canal shape It is important to visually inspect the ear impression for proper canal shape. An ear canal that widens at the end is not suitable for an IIC (C). C Canal widens after nd bend Not ok

20 0 Sonic Bliss Happiness sounds just like this Programming Bliss with EXPRESSfit Bliss can be programmed using EXPRESSfit fitting software version 03. or later, and may be used with the EXPRESSlink 3, HI-PRO, NOAHlink, or nearcom wireless programming interfaces. The New Standard (no.) programming cables are required. Note! A fresh battery must be inserted into all Bliss minibte and custom hearing instruments (not necessary for Bliss BTEs) prior to programming. Attaching programming cables Bliss BTE hearing instruments Open the battery door fully to reveal the programming socket. Plug the end of the cable into the programming socket as pictured.

21 Sonic Bliss Happiness sounds just like this Bliss minibte hearing instruments Insert a fresh battery into the hearing instrument, and close the battery door fully. Open the Program Button door fully to reveal the programming socket. 3 Plug the end of the cable into the programming socket as pictured. 3 Bliss custom hearing instruments Insert a fresh battery, and open the battery door slightly. With the black dot facing up, insert the end of the FlexConnect Mini into the space between the battery door and the hinge until the black dot touches the faceplate. Close the battery door. Plug the end of the cable into the FlexConnect Mini programming socket. 3 Place the instrument in the patient s ear and drape the strip over and behind the ear.

22 Sonic Bliss Happiness sounds just like this Programming Bliss Using the EXPRESSfit Fitting Software Launch the EXPRESSfit fitting software to proceed. Open EXPRESSfit When starting a new fitting, press Use Attached Devices on the Product Overview screen if instruments are connected, or select an instrument family for simulation. Use attached devices With the instrument detected, follow the prompts to start a new fitting with the hearing instrument.

23 Sonic Bliss Happiness sounds just like this 3 Acoustics EXPRESSfit will recommend acoustic options based on the patient s audiogram. You can accept the recommendations by clicking Apply or modify the acoustics by selecting the Thin Tube or Earhook, Earpiece, or Venting to be used for your patient. Navigation toolbar Use the toolbar located on the left side of your screen to navigate through the fitting process. The main screens for each segment will be reviewed in the following pages.

24 4 Sonic Bliss Happiness sounds just like this Edit hearing instrument On this screen, you can change the acoustics or the selected hearing instrument. Edit client info This screen allows you to review and select your patient s personal data, and customize the experience level and fitting rationales. The default fitting rationale is Best Fit Fast. Your patient s audiogram and the selected fitting rationale will determine the gain and frequency response for the fitting. You may also wish to perform in situ measurements or include additional audiometric data to further customize the fitting. These functions are accessible by clicking on the appropriate tab at the bottom of the screen.

25 Sonic Bliss Happiness sounds just like this 5 Manage programs This screen allows you to add, copy, swap, and delete listening programs. The Universal Program (P) and Telephone Program (P) are set by default. To view or change features, select the appropriate program, then select the Features tab near the bottom of your screen.

26 6 Sonic Bliss Happiness sounds just like this Features Optimize the features specific to each program on the Features screen. The buttons at the bottom of the screen allow you to easily switch between programs. Impulse Noise Reduction suppresses short-duration, high-intensity sounds Speech Priority Noise Reduction manages distracting environmental noises to provide comfort and clarity according to your patient s needs Directionality provides focus to sounds in front of the listener Wind Noise Reduction provides relief from noise resulting from windy environments Binaural Coordination coordinates the instruments environmental classification Click the icon to select features monaurally or binaurally. Additional program access The arrow on the bottom right of the screen allows you to configure features for the SoundGate, DAI/FM and Auto Telephone Programs, depending on the hearing instrument model or optional accessories selected.

27 Sonic Bliss Happiness sounds just like this 7 Fit hearing instrument Use this screen to make gain adjustments and view the hearing instrument s frequency response relative to prescribed targets. To adjust the levels of fine-tuning, click the Simplified, Standard, or Advanced tabs. You may also measure the feedback margin by clicking the Feedback Manager tab near the bottom of your screen. Click Measure and follow the prompts to complete measurements for one or both ears. You may also select the Fitting Assistant tab to find solutions to common problems at any time during the fitting process. Click the icon to select whether these changes are made for a single program or for all listening programs. Click the arrow on the bottom right of the screen to access the SoundGate Phone, SoundGate Entertainment, Auto Telephone and DAI/FM Programs for adjustment.

28 8 Sonic Bliss Happiness sounds just like this View data analysis Once Bliss instruments have been worn at least 8 hours, statistics of program usage, time of use, environments, and volume adjustments can be viewed by entering the View Data Analysis screen. Bliss 00 offers the option to track volume adjustments made by the patient and gradually apply default volume settings over time. When Data Learning is enabled, volume changes will be applied only after 0 hours of use in the same listening program. Data Learning is turned off in EXPRESSfit by default.

29 Sonic Bliss Happiness sounds just like this 9 Finish session Options In this section you will find access to all local controls, including volume control range configurations and program selector settings. From this screen you can also synchronize volume and program controls, and pair Bliss with the RC-P Remote Control or SoundGate communication device. Audible indicators Select and demonstrate audible indicators on this screen. The frequency and level of these tones can be customized for better recognition. Save and quit Review program and device information, and save your session here. There is also space available for optional session comments on this screen.

30 30 Sonic Bliss Happiness sounds just like this Ordering Information Dispensing Kit Product Quantity Part Number Sonic BTE Dispensing Kit 7690 Ear Impression Tool Product Quantity Part Number Ear Impression Evaluation Tool, IIC Earhook Product Quantity Part Number Hook, Damped (BTE) 96 Hook, Damped (minibte) 454 Thin Tube Adapter Product Quantity Part Number Adaptor, So Thin Tube (BTE) 377 Adaptor, So Thin Tube (minibte) 3446 Thin Tubes 0.9 mm Product Quantity Part Number Thin Tube, 0.9 mm size 0 right Thin Tube, 0.9 mm size right Thin Tube, 0.9 mm size right Thin Tube, 0.9 mm size 3 right Thin Tube, 0.9 mm size 0 left Thin Tube, 0.9 mm size left Thin Tube, 0.9 mm size left Thin Tube, 0.9 mm size 3 left Thin Tubes.3 mm Product Quantity Part Number Thin Tube,.3 mm size 0 right Thin Tube,.3 mm size right Thin Tube,.3 mm size right Thin Tube,.3 mm size 3 right Thin Tube,.3 mm size 0 left Thin Tube,.3 mm size left Thin Tube,.3 mm size left Thin Tube,.3 mm size 3 left

31 Sonic Bliss Happiness sounds just like this 3 Thin Tube Domes Product Quantity Part Number Dome, Open, 6 mm Dome, Open, 8 mm Dome, Open, 0 mm Dome, Tulip Dome, Large Vent, 8 mm Dome, Large Vent, 0 mm 0 33 Dome, Large Vent, mm 0 33 Dome, Small Vent, 8 mm Dome, Small Vent, 0 mm Dome, Small Vent, mm Dome, Power, 6 mm Dome, Power, 8 mm Dome, Power, 0 mm Microphone Protection T-Cap, Black pack of 8 filters 3467 T-Cap, Dark Brown pack of 8 filters 3468 T-Cap, Medium Brown pack of 8 filters 3469 T-Cap, Light Brown pack of 8 filters 3476 T-Cap, Beige pack of 8 filters 3477 O-Cap, Beige pack of 8 filters 8009 O-Cap, Light Brown pack of 8 filters 800 O-Cap, Medium Brown pack of 8 filters 80 O-Cap, Dark Brown pack of 8 filters 80 Receiver Protection ProWax pack of 6 filters 3459 DAI Adapters DAI Adapter, BTE DAI ADAPTOR, minibte 9574 Programming Cables Flex Connect, Mini 7468 NOAH Link Prog Cables set HiPro/EXPRESSlink Prog cable blue/left HiPro/EXPRESSlink Prog cable red/right NOAH Link Prog cable blue/left NOAH Link Prog cable red/right

32 UK