SAFETY DATA SHEET Difficil-S Part A. Difficil-S Part A Powder

Transcription

1 SAFETY DATA SHEET DifficilS Part A SECTION 1. IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING 1.1 Product Identification Product Name Product Type Product 1.2. Relevant Identified uses of substance and uses advised against DifficilS Part A Powder 1.3. Details of supplier Clinimax Limited Shepherds Grove West Stanton Bury ST Edmunds Suffolk IP31 2AR UK Component of Surface Disinfectant. DifficilS Powders A and B are added at 1:400 in water, the resultant working solution contains approximately 300ppm chlorine dioxide in solution. The material is intended to be mixed with DifficilS Part B and water to make a Surface Disinfectant. The material should only be used in conjunction with Clinimax DifficilS Part B and mixed in accordance with the manufacturer s instructions using manufacturer s specified mixing equipment. Telephone +44 (0) address of person responsible for this SDS info@clinimax.co.uk 1.4. Emergency telephone number +44 (0) Opening Hours 9.00am to 4.30pm, Mon Fri SECTION 2. HAZARDS IDENTIFICATION 2.1 Classification according to Regulation (EC) No 1272/2008 [CLP] Ox Sol. 3 H272 may intensify fire; oxidiser Acute Tox. 4 H302 Harmful if swallowed Acute Tox 2 H330 Fatal if inhaled Skin Corr. 1B Causes severe skin burns and eye damage STOT RE 2 May cause damage to organs (spleen) through prolonged or repeated exposure Aquatic Acute 1 H400 Very toxic to aquatic life. Date of issue/revision: 06/12/16 1 of 17

2 Aquatic Chronic 3 H412 Harmful to aquatic life with longlasting effects For full text of CLP/GHS phrases: see SECTION 16. For further details on the health effects and symptoms: see SECTION Labelling in accordance with the classification Labelling and Packaging Regulation (EC) 1272 /2008 Hazard Statements Precautionary Statements Hazardous Ingredients Supplemental label requirements DANGER H272 May Intensify fire; oxidiser H302 Harmful if swallowed H314 Causes severe skin burns and eye damage H330 Fatal if inhaled H373 May cause damage to organs (spleen) through prolonged or repeated exposure H400 Very toxic to aquatic life H412 Harmful to aquatic life with longlasting effects P210 Keep away from heat P221 Avoid combustible materials and acids P260 Do not breathe dust/fume P273 Avoid release to the environment. Refer to special instructions/safety data sheet P280 Wear protective gloves/clothing/eye/face protection P302 + P352 IF ON SKIN: Wash with plenty of soap and water P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing Sodium Chlorite, Sodium Dodecyl Sulphate EUH032 Contact with acids liberates toxic gas EUH071 Corrosive to the respiratory tract Special packaging requirements Containers to be fitted with childresistant fastenings Tactile warning of danger Not applicable. Not applicable. 2.3 Other Hazards Handling and/or processing of this material may generate a dust which is corrosive to the respiratory tract. Fine dust clouds may form explosive mixtures with air. Date of issue/revision: 06/12/16 2 of 17

3 SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS 3.1 Substance Product/ingredient name Identifiers % Classification Type Regulation (EC) No 1272/2008 sodium chlorite EC: CAS: Sodium dodecyl sulphate EC: CAS: Sodium carbonate EC: CAS: Index: Acute Tox. 3, H301 Acute Tox. 2, H310 Acute Tox. 1, H330 Skin Corr. 1B STOT RE 2 H373 Aquatic Acute 1, H400 Aquatic Chronic 3 H Acute Tox. 4, H302 Skin Irrit. 2, H315 Eye Dam. 1 H318 Aquatic Acute 3, H412 <10 Eye Irrit. 2, H319 See Section 16 for the full text of the H phrases declared above. There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment, are PBTs or vpvbs or have been assigned a workplace exposure limit and hence require reporting in this section. Type [1] Substance classified with a health or environmental hazard. [1] [1] [1] Date of issue/revision: 06/12/16 3 of 17

4 SECTION 4. FIRST AID MEASURES 4.1 Description of first aid measures Eye contact Seek medical attention immediately. Flush eyes with plenty of water, also under eyelids. Check for contact lenses and remove if present and easy to do. Continue to rinse for at least 10 minutes and consult an eye physician immediately. Chemical burns must be treated promptly by a physician. Inhalation Skin contact Ingestion Protection of first aiders Seek medical attention immediately. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing perform artificial respiration with the aid of a pocket mask and contact the emergency services. Seek medical attention immediately. Remove contaminated clothing and shoes and flush contaminated skin with plenty of water. Continue to rinse for at least 10 minutes. Chemical burns must be treated promptly by a physician. Wash clothing before reuse. Clean shoes thoroughly before reuse. Seek medical attention immediately. Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do NOT induce vomiting. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Chemical burns must be treated promptly by a physician. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and contact the emergency services. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. No action shall be taken involving any personal risk or without suitable training. The rescuer should wear the appropriate PPE and follow all precautions to protect themselves and prevent contamination. 4.2 Most important symptoms and effects, both acute and delayed Potential acute health effects Eye contact Corrosive to eyes. Causes burns. Inhalation Skin contact Ingestion Overexposure signs /symptoms Eye contact Very toxic by inhalation. May give off gas, vapour or dust that is very irritating or corrosive to the respiratory system. Corrosive to the skin. Causes burns. Toxic in contact with skin. Toxic if swallowed. May cause burns to mouth, throat and stomach. Adverse symptoms may include the following: pain watering redness Date of issue/revision: 06/12/16 4 of 17

5 Inhalation Skin contact Ingestion Adverse symptoms may include the following: respiratory tract irritation coughing Adverse symptoms may include the following: pain or irritation redness blistering may occur Adverse symptoms may include the following: stomach pains, burns to the mouth and throat 4.3 Indication of any immediate medical attention and special treatment needed Notes to physician Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled. Specific treatments No specific treatment. SECTION 5. FIREFIGHTING MEASURES 5.1 Extinguishing media Suitable extinguishing media Unsuitable extinguishing media Use dry chemical powder. Do not use water jet. 5.2 Special hazards arising from the substance or mixture Hazards from the Contact with combustible material may cause fire. Fine dust clouds substance or mixture may form explosive mixtures with air. This material increases the risk of fire and may aid combustion. Hazardous thermal decomposition products 5.3 Advice for firefighters Special protective actions for firefighters Decomposition products may include the following materials: sulphur oxides halogenated compounds chlorine dioxide gas Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Move containers from fire area if this can be done without risk. Use water spray to keep fireexposed containers cool. This material is very toxic to aquatic organisms. Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or drain. Date of issue/revision: 06/12/16 5 of 17

6 SECTION 6. ACCIDENTAL RELEASE MEASURES 6.1 Personal precautions, protective equipment and emergency procedures For nonemergency personnel For emergency responders No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilt material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Do not breathe dust. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also Section 8 for additional information on hygiene measures. 6.2 Environmental precautions Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to the environment if released in large quantities. 6.3 Methods and materials for containment and cleaning up Small spill Less than 5 sachets. Wear gloves and eye safety wear as outlined in section 8. Avoid contact with the skin and eyes. Move containers from spill area. Sweep up material and place in a designated, labelled waste container. Place spilt material in an appropriate container for disposal. Do not use combustible absorbents, e.g. paper towels or saw dust to absorb spillages. Large spill For largescale spills of the powder ensure full personal protective equipment is worn. Avoid contact with the skin and eyes. Move containers from spill area. If unopened sachets are spilt these can be replaced in the container if undamaged and dry. Do not attempt to neutralise the spillage with acids. Avoid allowing the spilled material to get wet or using water to clean up spillages or residues, unless the quantity remaining is very small. Sweep up material and place in a designated, labelled waste container. Avoid creating dusty conditions and prevent wind dispersal. Do not use combustible absorbents, e.g. paper towels or saw dust to absorb spillages. Dispose of via a licensed waste disposal contractor. Note: see section 1 for emergency contact information and section 13 for waste disposal. 6.4 Reference to other sections See Section 1 for emergency contact information. See Section 8 for information on appropriate personal protective equipment. See Section 13 for additional waste treatment information. Date of issue/revision: 06/12/16 6 of 17

7 SECTION 7. HANDLING AND STORAGE 7.1 Precautions for safe handling Protective measures Protective measures Put on appropriate personal protective equipment (see Section 8). Do not get in eyes or on skin or clothing. Do not breathe dust. Do not ingest. Avoid release to the environment. Use only with adequate ventilation. Keep sachets in original box together with instructions for use and refer to these when handling. Keep away from acids. Keep away from combustible material. Advice on general occupational hygiene Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures. 7.2 Conditions for safe storage, including any incompatibilities Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from direct sunlight in a dry, cool and well ventilated area, away from incompatible materials (see section 10) and food and drink. Eliminate all ignition sources. Separate from acids. Separate from oxidizing materials. Separate from reducing agents and combustible materials. Do not store in unlabelled containers or packaging. Use appropriate containment to avoid environmental contamination. 7.3 Specific end use(s) Recommendations Industrial sector specific solutions Use only as a cleaning disinfectant and must be mixed with part B and water in accordance with the manufacturer s instructions. For use in the healthcare industry SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1 Control Measures Occupational exposure limits Recommended monitoring procedures Derived effect levels Predicted effect concentrations 8.2 Exposure controls Appropriate engineering controls Chlorine Dioxide: Long term exposure limit 0.1 ppm, 0.28mg.m³ (8hr TWA reference period), short term exposure limit 0.3 ppm, 0.84mg.m³ (15 minute reference period). None identified. No DNELs available. No PNECs available. Good general ventilation should be sufficient to control worker exposure to airborne contaminants. If dust is generated and ventilation is inadequate, use respirator that will protect against dust or local exhaust ventilation conforming to European (EN) Standards. Date of issue/revision: 06/12/16 7 of 17

8 Only use mixing and dispensing equipment specified by the manufacturer. Individual protection measures Hygiene measures Wash hands and forearms and any other contaminated area thoroughly after handling this chemical product, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location. Eye/face protection Skin protection : Hand protection Safety goggles or face shield giving complete eye protection complying with the European (EN) Standard EN 166 should be used when opening and mixing contents of the sachets. This is necessary to avoid exposure to mists or dusts. Chemicalresistant Nitrile or PVC gloves complying with the European (EN) Standards EN374 should be worn at all times when handling this chemical product during both mixing and end use of the disinfecting cleaning solution. Body protection Respiratory protection Environmental exposure controls Personal protective equipment for the body complying with European (EN) Standards should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. For normal use the following is advisable for both mixing and use of the working solution: Recommended: Safety Overalls or Safety Apron. In case of insufficient ventilation, wear suitable respiratory equipment complying with European (EN) Standards EN149. Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels. SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES 9.1 Information on basic physical and chemical properties Appearance Physical state Solid [powder] Colour White Odour None Odour Threshold None ph 10.6 [Conc. (% w/w): 1%] Melting point/freezing point Date of issue/revision: 06/12/16 8 of 17

9 Initial boiling point and boiling range Flash point Evaporation rate Flammability (solid, gas) Burning time Burning rate Vapour pressure Vapour density Relative density Partition coefficient: noctanol/ water Autoignition temperature Decomposition temperature Viscosity Explosive properties Oxidising properties 9.2 Other information No additional information. Not applicable. Not applicable. >300 o C >200 o C Not applicable. Not classified as explosive Oxidising solid, corrosive. SECTION 10. STABILITY AND REACTIVITY 10.1 Reactivity No specific test data related to reactivity available for this product or its ingredients Chemical stability The product is stable Possibility of hazardous reactions Contact with acids may liberate toxic gas (chlorine dioxide). Contact with combustible materials may cause fire or intensify fires. May react violently with highly flammable materials causing fire and explosion Conditions to avoid Avoid the creation of dust when handling and avoid all possible sources of ignition (spark or flame). Prevent dust accumulation. Avoid contact with strong acids, alkali or oxidising agents. Keep dry, except for when preparing solutions Incompatible materials 10.6 Hazardous decomposition products Reactive or incompatible with the following materials: acids oxidizing materials combustible materials reducing materials Contact with acids liberates very toxic gas (chlorine dioxide). Date of issue/revision: 06/12/16 9 of 17

10 SECTION 11. TOXICOLOGICAL INFORMATION 11.1 Information on toxicological effects Acute toxicity Product/ingredient Result Species Dose Exposure name sodium chlorite LC50 Inhalation Dust LD50 Dermal LD50 Oral Rat 230 mg/m3 4 hours Rabbit Rat 134 mg/kg 165 mg/kg Sodium dodecyl sulphate LD50 Oral Rat 1288 mg/kg Sodium carbonate LD50 Oral Rat 4090 mg/kg Conclusion/Summary Product/ingredient name sodium dodecyl sulphate Result Species Score Dose Observation Eyes Mild irritant Rabbit 250 Micrograms Eyes Moderate Rabbit 24 hours irritant 100 Eyes Moderate Rabbit 10 irritant Skin Mild irritant Dog 24 hours 25 Skin Mild irritant Guinea pig 24 hours 25 Skin Mild irritant Human 504 hours 0.3 Percent Skin Mild irritant Human 24 hours 0.06 Percent Skin Mild irritant Human 22 hours 10 Percent Skin Mild irritant Human 47 hours 0.5 Percent Skin Mild irritant Human 18 hours 2 Percent Skin Moderate irritant Human 48 hours 3 Percent Skin Moderate irritant Human 24 hours 0.1 Percent Skin Moderate irritant Mouse 24 hours 25 Skin Mild irritant Pig 24 hours 25 Date of issue/revision: 06/12/16 10 of 17

11 Skin Mild irritant Rabbit 24 hours 50 Skin Moderate irritant Rabbit 24 hours 25 Skin Mild irritant Human 2 hours 2 Percent sodium carbonate Eyes Mild irritant Rabbit 50 Eyes Moderate Rabbit 50 irritant Eyes Severe irritant Rabbit 50 Eyes Severe irritant Rabbit 24 hours 500 Conclusion/Summary Sensitisation Conclusion/Summary Mutagenicity Conclusion/Summary Carcinogenicity Conclusion/Summary Reproductive toxicity Conclusion/Summary Teratogenicity Conclusion/Summary Information on the likely routes of exposure None of the components are considered to be sensitising. None of the components are considered to be mutagenic. None of the components are considered to be carcinogenic. None of the components are considered to exhibit reproductive toxicity. None of the components are considered to exhibit developmental toxicity. Skin contact and inhalation of dust most likely routes. Potential acute health effects Eye contact Corrosive to eyes. Causes burns. Inhalation Skin contact Ingestion Very toxic by inhalation. May give off gas, vapour or dust that is very irritating or corrosive to the respiratory system. Corrosive to the skin. Causes burns. Toxic in contact with skin. Toxic if swallowed. May cause burns to mouth, throat and stomach. Delayed and immediate effects and also chronic effects from short and long term exposure Short term exposure Potential immediate effects Potential delayed effects Long term exposure Potential immediate effects Date of issue/revision: 06/12/16 11 of 17

12 Potential delayed effects Potential chronic health effects Conclusion/Summary Potential delayed effects General Repeated or prolonged inhalation of dust may lead to chronic respiratory irritation. Sodium chlorite is classified as STOT RE 2, this may cause damage to organs (spleen) through prolonged or repeated exposure SECTION 12. ECOLOGICAL INFORMATION 12.1 Toxicity Product/ingredient name sodium chlorite sodium dodecyl sulphate Result Species Exposure Acute EC ppm Fresh water Acute EC ppm Fresh water Acute LC50 75 ppm Marine water Acute EC50 15 mg/l Marine water Acute EC ug/l Fresh water Acute EC50 5 to 10 ppm Marine water Acute LC ug/l Marine water Acute LC ug/l Marine water Acute LC ug/l Fresh water Chronic NOEC 0.15 mg/l Fresh Water sodium carbonate Acute EC mg/l Fresh water Acute LC ug/l Fresh water Acute LC50 >5600 ppm Fresh water Acute LC ug/l Fresh water Conclusion/Summary Algae Pseudokirchneriella subcapitata Daphnia Daphnia magna <24 hours Fish Cyprinodon variegatus Algae Dunaliella tertiolecta Exponential growth phase Algae Pseudokirchneriella subcapitata Aquatic plants Macrocystis pyrifera Young Crustaceans Artemia sp. Daphnia Ceriodaphnia dubia Neonate Fish Cirrhinus mrigala Larvae 2 days 4.5 mm 51 mg Fish Oncorhynchus mykiss Juvenile (Fledgling, Hatchling, Weanling) Daphnia Daphnia magna Daphnia Daphnia magna Fish Morone saxatilis Larvae Fish Morone saxatilis Larvae The mixture is toxic to aquatic organisms. 4 days 48 hours 96 hours 72 hours 96 hours 4 days 48 hours 48 hours 96 hours 4 days 48 hours 96 hours 48 hours 96 hours Date of issue/revision: 06/12/16 12 of 17

13 12.2 Persistence and degradability Conclusion/Summary The organic components of this product are considered to be biodegradable Bio accumulative potential 12.4 Mobility in soil Soil/water partition coefficient (KOC) Mobility The components are all water soluble and are expected to partition to the aquatic compartment Results of PBT and vpvb assessment PBT A PBT / vpvb assessment has not been carried out but none of the components are expected to possess these properties. vpvb As above Other adverse effects No known significant effects or critical hazards. SECTION 13. DISPOSAL CONSIDERATIONS The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be consulted for any available usespecific information provided in the Exposure Scenario(s) Waste treatment methods Product Methods of The generation of waste should be avoided or minimised wherever possible. disposal Significant quantities of waste product residues should not be disposed of via the foul sewer but processed in a suitable effluent treatment plant. Dispose of surplus and nonrecyclable products via a licensed waste disposal contractor. Disposal of this product, solutions and any byproducts should at all times comply with the requirements of environmental protection and waste disposal legislation and any Regional local authority requirements. Small amounts can be made as per manufacturer s instructions and disposed of via the foul sewer with plenty of cold running water. Hazardous waste Packaging Methods of disposal Special precautions The classification of the product may meet the criteria for a hazardous waste. The generation of waste should be avoided or minimised wherever possible. Sachets should not be cleaned, rinsed or recycled. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains and sewers. Date of issue/revision: 06/12/16 13 of 17

14 SECTION 14. TRANSPORT INFORMATION ADR/RID ADN/ADNR IMDG IATA 14.1 UN number UN1479 UN1479 UN1479 UN UN proper shipping name 14.3 Transport hazard class(es) OXIDIZING SOLID, N.O.S.,(Sodium chlorite) OXIDIZING SOLID, N.O.S.,(Sodium chlorite) 5.1 OXIDIZING SOLID, N.O.S.,(sodium chlorite), Marine pollutant. OXIDIZING SOLID, N.O.S.,(Sodium chlorite) 14.4 Packing group 14.5 Environmental hazards 14.6 Special precautions for user Additional information 14.7 Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code III III III III Yes Yes Yes Yes Hazard identification Number 50 Limited quantity 5 kgs Special provisions 274 Tunnel code (E) Emergency schedules (EMS) FA, SQ Passenger and Cargo Aircraft Quantity limitation: 25 kg Packaging instructions: 516 Cargo Aircraft Only Quantity limitation: 100 kg Packaging instructions: 518 Limited Quantities Passenger Aircraft Quantity limitation: 10 kg Packaging instructions: Y516 Date of issue/revision: 06/12/16 14 of 17

15 SECTION 15. REGULATORY INFORMATION 15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture EU Regulation (EC) No. 1907/2006 (REACH) Annex XIV List of substances subject to authorisation Substances of very high concern None of the components are listed Annex XVII Restrictions Not applicable. on the manufacture, placing on the market and use of certain dangerous substances, mixtures and articles Other EU regulations Europe inventory Black List Chemicals Priority List Chemicals Integrated pollution prevention and control list (IPPC) Air Integrated pollution prevention and control list (IPPC) Water International regulations Chemical Weapons Convention List Schedule I Chemicals Chemical Weapons Convention List Schedule II Chemicals Chemical Weapons Convention List Schedule III Chemicals All components are listed or exempted. Not listed. Not listed. Not listed. Not listed. Not listed. Not listed. Not listed Chemical Safety Assessment This product contains substances for which Chemical Safety Assessments are still required. Date of issue/revision: 06/12/16 15 of 17

16 SECTION 16. OTHER INFORMATION Abbreviations and acronyms ATE = Acute Toxicity Estimate CLP = Classification, Labelling and Packaging Regulation [Regulation (EC) No. 1272/2008] DNEL = Derived No Effect Level EUH statement = CLPspecific Hazard statement PNEC = Predicted No Effect Concentration RRN = REACH Registration Number. Procedure used to derive the classification according to Regulation (EC) No. 1272/2008 [CLP/GHS] Classification Justification Ox. Sol. 3, H272 Expert judgment Acute Tox. 4, H302 Calculation method Acute Tox. 3, H311 Calculation method Acute Tox. 2, H330 Calculation method Skin Corr. 1B Calculation method Aquatic Chronic 3, H412 Calculation method Aquatic Acute 1, H400 Calculation method STOT RE 2 Calculation method Full text of abbreviated Hazard statements Full text of classifications [CLP/GHS] H272 May intensify fire; oxidiser. H301 Toxic if swallowed. H302 Harmful if swallowed. H311 Toxic in contact with skin. H315 Causes skin irritation. H319 Causes serious eye irritation. H330 Fatal if inhaled. H400 Very toxic to aquatic life. Acute Tox. 1, H330 ACUTE TOXICITY: INHALATION Category 1 Acute Tox. 2, H310 ACUTE TOXICITY: SKIN Category 2 Acute Tox. 2, H330 ACUTE TOXICITY: INHALATION Category 2 Acute Tox. 3, H301 ACUTE TOXICITY: ORAL Category 3 Acute Tox. 3, H311 ACUTE TOXICITY: SKIN Category 3 Acute Tox. 4, H302 ACUTE TOXICITY: ORAL Category 4 Aquatic Acute 1, H400 AQUATIC TOXICITY (ACUTE) Category 1 Aquatic Chronic 3, H412 AQUATIC TOXICITY (CHRONIC) Category 3 Skin Corr. 1B STOT RE 2, H373 Eye Dam. 1 H318 SERIOUS EYE DAMAGE Category 1 Eye Irrit. 2, H319 SERIOUS EYE DAMAGE/ EYE IRRITATION Category 2 Ox. Sol. 3, H272 OXIDIZING SOLIDS Category 3 Skin Irrit. 2, H315 SKIN CORROSION/IRRITATION Category 2 Date of issue/revision: 06/12/16 16 of 17

17 Date of printing Date of issue/ Date of 06/12/16 revision Date of previous issue 29/07/16 Version 3 Changes since previous revision: Artwork and header adjustments Notice to reader To the best of our knowledge, the information contained herein is accurate. However, neither the abovenamed supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist. Date of issue/revision: 06/12/16 17 of 17