Denture Duplicator Flask
|
|
|
- Austin Rodgers
- 5 years ago
- Views:
Transcription
1 Denture Duplicator Flask Package Contents REF 0398 One Flask REF 0395 One Flask, Jet Tooth Shade Powder: 2x45 g Net Wt., Jet Denture Repair Powder: 2x100 g Net Wt., Jet Liquid: 236 ml Net Vol., Silicone Spray: 236 ml Net Vol., measuring cups, glass dropper REF 0399 One Flask, Jet XR Powder: 2x45 g Net Wt., Ortho-Jet Powder: 2x100 g Net Wt., Jet Liquid: 236 ml Net Vol., Silicone Spray: 236 ml Net Vol., measuring cups, glass dropper Intended Purpose To create a duplicate denture from a patient s original denture, or to create a surgical guide/implant stent. DENTURE DUPLICATION Other Materials / Equipment Needed Alginate Spatula Aquapres / pressure curing unit, optional Instructions for Use 1 Bur, pumice, lab polish Measuring cup Jet Adjusters, optional Jet Seal, optional Spray inside of flask with silicone spray to facilitate post procedure clean-up. Fill half of flask with alginate.
2 2 Place existing denture into alginate. Teeth should be perpendicular to the bottom of the flask. With wet fingers, smooth alginate from borders of denture to rim of flask, removing excess alginate. After alginate is set, trim excess that covers the denture Spray denture and surrounding alginate with silicone spray. Fill other half of flask and palate side of denture with alginate. With wet fingers, smooth alginate to ensure complete coverage, working quickly before alginate sets. Close flask with steady pressure. Secure thumb screw and allow alginate to set. Trim excess alginate. Open flask and remove denture. If there are any gross defects in the impression, make corrections now or retake impression.
3 6 7 8 Select appropriate Jet Tooth Shade powder. Fill teeth in impression as follows: Shake liquid. Moisten surface with Jet liquid. Spray on Jet powder. Alternate liquid and powder until teeth are filled to gingival border. When acrylic appears dull, use small spatula to push acrylic down to redefine gingival borders of all teeth. Cure for 15 minutes, either on bench or, for best results, in Aquapres at 30 psi. (Curing under pressure eliminates porosity, making a strong, dense, aesthetically superior denture.) With bur, trim teeth interproximally. Place trimmed teeth back into impression. Place 30cc of Jet Denture Repair powder into measuring cup. Add 15cc of Jet liquid and mix for 10 seconds. Pour 75% of mixture into lower half of flask. Pour remaining acrylic over palate on upper half of flask. With slow and steady pressure, close and secure flask. (Excess speed or pressure may cause distortion.) Remove excess acrylic flashing from outside of flask, as hardened acrylic will inhibit movement of hinge and thumb screw. Cure for 15 minutes as previously instructed.
4 9 Remove denture from flask, clearing away all excess acrylic. Grind to a smooth finish. Polish with pumice, then high shine. 10 Use Jet Adjusters for polishing and characterizing teeth. Finish with Jet Seal to fill in any surface porosity and leave a shiny, finished surface. CLEAR SURGICAL GUIDE / IMPLANT STENT Other Materials / Equipment Needed Alginate Spatula Measuring Cup Aquapres pressure curing unit, optional Bur, pumice, lab polish Instructions for Use Clear Guide Follow Steps 1-5 as shown for Denture Duplication. 6. Place 30cc of Ortho-Jet powder into a measuring cup. Add 15cc of Jet liquid and mix for 10 seconds. Pour 75% of mixture into the impression of the denture in the lower half of flask. Ensure that acrylic flows completely into all incisal and occlusal spaces without trapping any air. Pour the rest of the mixture over the palate on the upper half of the flask.
5 7. With slow and steady pressure close and secure flask. (Excess speed or pressure may cause distortion.) Cure for 20 minutes either on bench or, for best results, in Aquapres at 30 psi. Follow Step 9 for the Denture Duplication to complete procedure. Instructions For Use Radiopaque Appliance Follow steps 1-5 as shown for Denture Duplication. 6. Follow instructions for Denture Duplication, replacing the Jet Tooth Shade powder with the Jet XR Opaque powder. 7. Same as for Denture Duplication. 8. Follow instructions for Denture Duplication, replacing the Jet Denture Repair powder with the Jet XR Shadow powder. Follow Step 9 for Denture Duplication to complete procedure. Warranty Manufacturer warrants this product to be free from manufacturing defects for one year from date of purchase. Warranty is void if product is not used for intended purpose or not used as instructed.
6 MediMark Europe Sarl BP Grenoble Cedex 2 France Lang Dental Mfg. Co., Inc. 175 Messner Drive Wheeling, IL USA Ph Fax Lang Dental Mfg. Co., Inc. LANG and AQUAPRES are the registered trademarks of Lang Dental Mfg. Co., Inc. JET, JET XR and ORTHO-JET are the trademarks of Lang Dental Mfg. Co., Inc. All rights reserved. LDD 0398 R.8
VIP Partner Laboratory (PL) Process Flow
VIP Partner Laboratory (PL) Process Flow 1. VIP Software 2. CT Scan Appliance 3. CT Scan Clinician purchases VIP for PL fabricates CT Scan Appliance Patient submitted for scans treatment planning purposes
Surgical Guide Technique
Surgical Guide Technique Safety glasses should be worn for all lab procedures as well as gloves when handling acrylics. Items featured in this technique are found on the last page. 1 Select a denture tooth
Steps in construction of an interim dental implant-supported hybrid prosthesis:
Steps in construction of an interim dental implant-supported hybrid prosthesis: 1. Identify the desired tooth position (natural teeth, dentures, etc.) in order to plan for Implant placement. 2. Make impressions
Invisible Retainer with Single-Tooth Pontic Fabrication Technique (Multi-Tooth Pontic Procedure also available)
Invisible Retainer with Single-Tooth Pontic Fabrication Technique (Multi-Tooth Pontic Procedure also available) Safety glasses should be worn for all lab procedures as well as gloves when handling acrylics.
DURATEMP Temporary Crown & Bridge Material. Temrex Corporation October 2009
DURATEMP Temporary Crown & Bridge Material Temrex Corporation October 2009 DURATEMP Temporary Crown & Bridge Material Overview Product Characteristics Physical Properties Case Report Instructions Ordering
Austenal PermaSoft Soft Denture Liner
Austenal PermaSoft Soft Denture Liner Directions for Use Laboratory Technique Chairside Technique Indications for Use: Intended for use as soft liner for acrylic full dentures and the acrylic saddle areas
ZEST DANVILLE MATERIALS PERIOSCOPY
ZEST DANVILLE MATERIALS PERIOSCOPY Attachment Processing Material is easy to use and predictable when processing attachments into full and partial overdentures,using either a chairside or laboratory procedure.
Occlusal Splint Fabrication Technique
Occlusal Splint Fabrication Technique Safety glasses should be worn for all lab procedures as well as gloves when handling acrylics. Items featured in this technique are found on the last page. 1 Mount
STEP-BY-STEP-ANLEITUNG
STEP-BY-STEP-ANLEITUNG VON TECHNIKERN FÜR TECHNIKER LABORATORY PROCEDURES, STEP BY STEP BY TECHNICIANS FOR TECHNICIANS Eclipse junior Laboratory Procedures, Step by Step* Splints Drilling Stents Temporaries
Invisible Retainer with Multi-Tooth Pontic Fabrication Technique (Single-Tooth Pontic Procedure also available)
Invisible Retainer with Multi-Tooth Pontic Fabrication Technique (Single-Tooth Pontic Procedure also available) Safety glasses should be worn for all lab procedures as well as gloves when handling acrylics.
INJECTION TECHNOLOGY FOR DENTURE PRODUCTION
INJECTION TECHNOLOGY FOR DENTURE PRODUCTION Ofer Darey, master-technician, consultant, Sun Rise Laboratories, Israel Interest to production of removable dentures from thermoplastic materials, which is
DIRECTIONS FOR USE. Laboratory Technique Chairside Technique
Sealer: Contains: Methyl Ethyl Ketone/Danger/Highly flammable liquid and vapour./causes serious eye irritation./may cause drowsiness or dizziness./keep away from heat, sparks, open flames, and hot surfaces.
Index. Why Choose TCS UK? For the dentist 4. For the lab 7. Why Choose tcs material? 8. tcs Unbreakable 9. tcs iflex 10.
Why Choose TCS UK? As always, our mission is to be the company you can rely on for removable, partial material and equipment, providing outstanding customer service and high quality products. Made in the
DENTAL MATERIALS STUDY GUIDE
DENTAL MATERIALS STUDY GUIDE WORKSHEET Dentalelle Tutoring www.dentalelle.com Study Guide for Dental Materials Dentalelle Tutoring 1. When completing a large composite restoration, how should the composite
Hex-Lock Abutment System. Restorative Manual
System Restorative Manual 32 Restorative options with s s are manufactured from titanium alloy and used as the support foundation for single- or multiple-unit cement-retained, partially edentulous fixed
Listing of Standards By Task
Orthodontics Listing of Standards By Task ORTHODONTICS 1. Disinfect the impression and/or model 2. Evaluate the prescription for completeness 3. Document changes to the prescription and/or design requirements
Product Ordering Information
Attachment Processing Material is easy to use and predictable when processing attachments into full and partial overdentures,using either a chairside or laboratory procedure. Two size options to suit your
Relining and Rebasing of complete denture
Relining and Rebasing of complete denture It is the procedures used to resurface the tissue-side of a denture with new material layer, thus producing an accurate adaptation to the denture foundation area.
ÆLITE Composites. Bisco. Instructions for Use. Light- Cured. U.S. Patent: 6,709,271
Bisco ÆLITE Composites 0459 Light- Cured Instructions for Use U.S. Patent: 6,709,271 IN-131R6 Rev. 4/16 BISCO, Inc. 1100 W. Irving Park Road Schaumburg, IL 60193 U.S.A. 847-534-6000 1-800-247-3368 Caution:
PARTIAL MOBILE DENTURE with Vertys Prothesis Excel / Plus termo-polimerizing resin
PARTIAL MOBILE DENTURE with Vertys Prothesis Excel / Plus termo-polimerizing resin What you need for this working: EQUIPMENT 10-0010 VERTYS SPLIT CAST & GUM 10-100 APOLIX 10-3000 AR.GO 10-2501 FURBO ALU
Peninsula Dental Social Enterprise (PDSE)
Peninsula Dental Social Enterprise (PDSE) Laboratory Procedures for Dentures and Indirect Restorations Version 1.0 Date approved: November 2016 Approved by: The Board Review due: November 2019 Policy will
We express. Acrylics rich in color and texture. GENERAL PRODUCT INFORMATION
We express Saint Basil Cathedral, Rusia. Visual riches for a changing aesthetic. Acrylics rich in color and texture. GENERAL PRODUCT INFORMATION Acrylic resins result from a mixture of powdered polymers
Listing of Standards By Task
Listing of Standards By Task PARTIAL DENTURES 1. Disinfect the impression and/or model 2. Evaluate the prescription for completeness 3. Document changes to the prescription 4. Evaluate the impression or
FLEXSTAR-V. Flexible Appliances. Instruction Manual
FLEXSTAR-V TM Flexible Appliances Instruction Manual Aesthetic Comfort Invisible Partial Dentures, Comfortable & Metal-Free Index Survey and Design Master Model...3 Clasping...3 Block Out Master Model
eliminate interlocking with new QUick Up method
eliminate interlocking with new QUick Up method TissUe colored implant pick-up system THe new QUick Up TecHniQUe in a complete system eliminates THe risk of interlocking In many cases the fit of full dentures
R.A.P.T.O.R. SYSTEM. Bisco. Instructions for Use. Composite/Porcelain Finishing Burs. U.S. Patent: 5,779,476
Bisco R.A.P.T.O.R. SYSTEM Composite/Porcelain Finishing Burs. 0459 Instructions for Use U.S. Patent: 5,779,476 IN-049R5 Rev. 3/16 BISCO, Inc. 1100 W. Irving Park Rd. Schaumburg, IL 60193 U.S.A. 847-534-6000
Full Arch Rehabilitation All-on-4 Technique Restorative Steps Recipe for Success
Full Arch Rehabilitation All-on-4 Technique Restorative Steps Recipe for Success Treatment Planning/Diagnosis 1. Setup meeting with Treatment Team to discuss case communication is key 2. Qualifying the
UnBreakable. Arian Deutsch, CDT
UnBreakable Arian Deutsch, CDT UnBreakable is there such a material? In Dentistry, the quest for a material that blends with nature both esthetically and functionally has been a long journey indeed. Many
FR Attachment Instructions Removable Partial Dentures
www.preat.com 800-232-7732 FR Attachment Instructions Removable Partial Dentures 1 2 Adjust the master cast on mounting platform of the surveyor to the chosen angle of insertion. Check to be sure the tooth
ident CT Guide Protocol
ident CT Guide Protocol The ident computer planning and iguide production starts with the CT Guide. This is a simple device which can be made by a dental technician, but it is essential that it is made
Occ 5002, Summer Semester /24/2010
Trimming Casts: Occlusion 5002 (three types) 1. Removable casts with vestibule 2. Fixed cast with no vestibule 3. Bleaching cast with no palate What do we know? Pouring casts Trimming casts Duplicating
Gingiva Solution SR Phonares II, IvoBase, SR Nexco
Gingiva Solution SR Phonares II, IvoBase, SR Nexco Preface 5 Framework design 6 Framework preparation 8 Finishing of the denture base 10 Gingival modification 12 Mobile mucosa 14 Immobile mucosa 16 Lip
STEP-BY-STEP INSTRUCTIONS ON TEMPORARY ABUTMENTS. Straumann Temporary Abutments, VITA CAD-Temp
STEP-BY-STEP INSTRUCTIONS ON TEMPORARY ABUTMENTS Straumann Temporary Abutments, VITA CAD-Temp The ITI (International Team for Implantology) is academic partner of Institut Straumann AG in the areas of
1. Visually survey the cast for discrepancies and surface defects. 2. Remove surface defects and fill unnatural indentations.
PROCEDURE CHECKLIST: SURVEY AND DESIGN 1. Visually survey the cast for discrepancies and surface defects. 2. Remove surface defects and fill unnatural indentations. 3. Visually survey cast to determine
Removable Partial Dentures
Removable Partial Dentures Replacement of missing teeth Fixed partial denture Removable partial denture Complete removable Transitional denture Partial removable Implant retained prosthodontics No prosthetic
LOCATOR ROOT ATTACHMENT SYSTEM
TECHNIQUE MANUAL LOCATOR ROOT ATTACHMENT SYSTEM IMPORTANT: This document contains the most current instructions for use. Please, read and retain. DESCRIPTION: Universal hinge, resilient attachment for
Fuji II LC. A Perfect Choice
A Perfect Choice is a remarkable restorative material The world s first resin-reinforced glass ionomer has remained the benchmark for light cured glass ionomer cements, delivering more than 15 years of
GUIDELINES FOR PROCESSING CELTRA DUO
GUIDELINES FOR PROCESSING CELTRA DUO 2 CONTENTS Minimum wall thickness 4 CAD / CAM processing 5 Finishing / polishing 5 Staining and glazing 5 Glaze-firing 7 Firing recommendations 8 Cementing 9 Ordering
Nexco Flask. Veneered. in a jiffy. The flask for the press technique with laboratory composites
SR Nexco Flask The flask for the press technique with laboratory composites Veneered in a jiffy Many small components lead to a great result Flexibility mirrored in every detail Developed by experts The
DPI Luting Cement. DPI Restorative Cement
DPI Luting Cement DPI Luting Cement is Type I glass ionomer white luting cement. DPI glass ionomers are remarkably biocompatible and can be safely used in deep cavities provided the pulp is not exposed,
2. Gap closure and replacement of the missing tooth 35 with directly modelled bridge region 34-36
GrandTEC Test Kit Dear User, This Test Kit has been put together to enable you to test GrandTEC on the model before using it in a clinical situation. GrandTEC is a resin-impregnated glass fibre strip.
Complete denture copy technique A practical application
Singapore Dental Journal 35 (2014) 65 70 Available online at www.sciencedirect.com journal homepage: www.elsevier.com/locate/sdj Case report Complete denture copy technique A practical application Steven
Chairside Reference Guide
Chairside Reference Guide With this Chairside Reference Guide, you re on your way to efficiency and accuracy with LUMINEERS with LUMITray. As you familiarize yourself with the procedure, follow these
Product Information. Meliodent The solution for every denture Effective material from a proven partner. Giving a hand to oral health.
Product Information Meliodent The solution for every denture Effective material from a proven partner Giving a hand to oral health. Meliodent products from Kulzer. A range of impressive cost effective
Instructions for Use SomnoDent Signature and Standard Line Fusion, Flex, Classic, Herbst Advance, Herbst Telescopic, Herbst Shim, AIR & AIR+ Devices
Instructions for Use SomnoDent Signature and Standard Line Fusion, Flex, Classic, Herbst Advance, Herbst Telescopic, Herbst Shim, AIR & AIR+ Devices Shim www.somnomed.com 1 Introduction The SomnoDent is
Use of the Sicat Surgical Guide In Reconstruction of the Hemi-Mandilectomy Patient
Use of the Sicat Surgical Guide In Reconstruction of the Hemi-Mandilectomy Patient Dr. Michael J. Maginnis Dr. Glenn E. Appleton Prosthodontics and Family Dentistry www.drsmanda.com Sarcoma of the Mandible
Complete denture impressions
Lec.5 Complete denture impressions د. غسان الطائي Dental Impression: a negative imprint of an oral structure used to produce a positive replica of the structure to be used as a permanent record or in the
HydroSet. Fast-setting HA bone substitute
HydroSet Fast-setting HA bone substitute Features The HydroSet material is formulated to harden in a wet field environment. Fast-setting Excellent wet-field properties Injectable or manual implantation
Height* FC width Prep depth RC width 4.0mm+ 4.3mm N/A 6.3mm
STERN ERA IMPLANT ABUTMENT Summary Resilient precision overdenture attachment. Universal hinge with vertical movement. Titanium abutment, nylon male. Manufactured for most popular screw and cylinder implants.
IvoBase Material. The innovative denture base material. Tissue friendly, tough, predosed
Material The innovative denture base material Tissue friendly, tough, predosed Denture base material of The innovative denture base material Material The fabrication of every quality prosthetic appliance
SKELETAL PROTHESIS with Vertys Prothesis Excel / Plus heat-curing resin
SKELETAL PROTHESIS with Vertys Prothesis Excel / Plus heat-curing resin What you need for this working: EQUIPMENT 10-0010 VERTYS SPLIT CAST & GUM 10-100 APOLIX 10-3000 AR.GO 10-2501 FURBO ALU BIG 10-130
Universal Plunger Loc Attachment
Universal Plunger Loc Attachment www.preat.com 800-232-7732 Universal Plunger Loc Complete Universal 7.5mm length TI plunger attachment. Compatible with Lew Passive and Swiss Loc NG. 1.5mm plunger, 7.5mm
Pala Digital Dentures. Better Precision. Faster Production. Higher Profitability. Giving a hand to oral health.
Brochure Get great results with fully 3D printed options designed to save time and cost! Pala Digital Dentures Better Precision. Faster Production. Higher Profitability. Giving a hand to oral health. The
The Essential Guide to Chairside Denture Reline
Clinical Technique: Chairside Denture Reline Made Easy The Essential Guide to Chairside Denture Reline Do you think chairside hard and soft denture reline procedures are messy and complicated? In this
Digital Impression Scanning
Digital Impression Scanning Table of Contents Using ScanIt Orthodontics (Recommended Software) Software Settings... 1 Control Panel... 1 System Settings... 1 Export Format... 1 Filling Out Patient Information...
Fuji ORTHO LC CAPSULE. 1 Capsule = 1 Full Arch Bonded
Efficient Bonding With Fuji ORTHO LC CAPSULE 1 Capsule = 1 Full Arch Bonded Prior To Bonding Appointment Fuji Ortho LC Capsules stored in the refrigerator Glass slab stored in the freezer (or refrigerator)
Tips & Tricks Direct fabrication of provisionals. Giving a hand to oral health.
Tips & Tricks Tips & Tricks Direct fabrication of provisionals. Giving a hand to oral health. Content 01 02 Manufacturing techniques p. 06 Impression materials p. 07 06 07 Preparation of provisional crown
Annotation to the lesson 21 Topic: Methods of provisory crowns fabrication. Chair-side technique. Evaluation of
Annotation to the lesson 21 Topic: Methods of provisory crowns fabrication. Chair-side technique. Evaluation of crown fitting quality Contemporary methods of restoration of tooth tissues pathology, using
Construction of Removable Partial Denture
Construction of Removable Partial Denture Peter Hermann Department of Prosthodontics Semmelweis University Treatment options for edentulous spaces Fixed prosthodontics (crowns/bridges) Removable prosthodontics
Solid Zirconia Full-Arch Implant Prosthesis (Protocol C All-CAD with Multi-Unit Abutments) BruxZir. FIRST Appointment. The BruxZir
(Protocol C All-CAD with Multi-Unit Abutments) Step-by-Step Restorative Protocol C The BruxZir Full-Arch Implant Prosthesis offers a fixed, all-zirconia implant solution for edentulous patients desiring
Quick Up. Self-curing luting material for attachments and secondary components in dentures
Self-curing luting material for attachments and secondary components in dentures One set for all luting needs In many cases the hold of full dentures is unsatisfactory. The main reasons for this are bone
Introducing the Pala 3D-printed Denture
ebook Create your best workflow and optimize production with cara 3D printing technology. Introducing the Pala 3D-printed Denture Powered by cara Print 4.0 and dima Print materials. < 2 hrs. Giving a hand
Reference to primary publication Properties of alginates in ZWP 4/2014 Xantalgin Crono - Introduction
Reference to primary publication in ZWP 4/2014 Dr. Marcus Holzmeier, Wuerzburg Xantalgin Crono - Highly accurate alginate impressions. Introduction Even today when digital impression techniques are gaining
Total Rehabilitation Of Poor Edentulous Arches With Metal Denture Bases And Finger Prosthesis.
CASE REPORT Total Rehabilitation Of Poor Edentulous Arches With Metal Denture Bases And Finger Prosthesis. Dr. Rajni Kalla, Dr. Sunil Kumar M V 2, Dr. Harikesh Rao 3, 1- M.D.S., Senior Lecturer; 2- Professor
Denture Troubleshooting Guide
Denture Troubleshooting Guide Technical bulletin from National Dentex Comfort Sore spot in vestibule upper or lower denture Sore spot in upper post dam. (posterior limit of upper) Single sore spots on
Excel Formula Dental Products
Dental Products Welcome to St. George Technology Our world class scientists continuously research and develop our extensive line of plastics, acrylics, and specialized polymers to accommodate various industries
Triad Visible Light Cure System
Triad Visible Light Cure System Triad Visible Light Cure System Denture Relines & Repairs For Complete Control from Design to Delivery Dentsply Sirona s unique Visible Light Cure Technology delivers maximum
STAR DENTAL LAB JACK FOUNTAIN C.D.T CEDAR PARK TX Please cut out
STAR DENTAL LAB CEDAR PARK TX 78613 512-267-6776 Dr, Thank you for taking time to look over our services. We are Austin area NOBEL ESTHETIC LAB that specializes in implant bars and custom abutments. We
ADJUSTABLE HERBST APPLIANCE - OASYS HINGE ACRYLIC
P SYSTEMS The delivery visit should confirm the fit and comfort of the appliance, as well as the patients ability to insert and remove the appliance properly and without difficulty. It may be necessary
DIGITAL WORKFLOWS IN THE PRIVATE PRACTICE TOURO DENTAL SEMINAR MARCH 9, 2018
DIGITAL WORKFLOWS IN THE PRIVATE PRACTICE TOURO DENTAL SEMINAR MARCH 9, 2018 WORKFLOW FOR SINGLE UNIT CROWN/ MULTIPLE UNIT PREP RETRACTION SCAN PREP ARCH SCAN OPPOSING SCAN "BITE" SEND TO LAB PRINT MODELS
synocta Meso abutment for cement-retained restorations PROSTHETICS Step-by-step instructions
synocta Meso abutment for cement-retained restorations PROSTHETICS Step-by-step instructions INTRODUCTION synocta Meso abutment for cement-retained restorations 1 The synocta Meso abutments, available
ACRYL-MARVEL STEPS TO SUCCESS
ACRYL-MARVEL STEPS TO SUCCESS (READ CAREFULLY PRIOR TO ACRYL-MARVEL USE) 800.228.6696 951.270.0606 www.dentalventures.com ACRYL-MARVEL STEPS FOR SUCCESS (READ CAREFULLY PRIOR TO ACRYL-MARVEL USE) ACRYL-MARVEL
Watson Dental Lab Fixed Hybrid Protocol
Watson Dental Lab Fixed Hybrid Protocol Watson Dental Lab has put Protocols in place to: Ensure maximum quality and fit of the final restoration. Maximize Dr. /Patient/ Lab communication and participation
illustrated technique guide
DENTSPLY Caulk 38 West Clarke Avenue Milford, DE 9963 www.dentsply.com www.caulk.com -302-422-45 In Canada call -800-263-437 illustrated technique guide Complete Luting System for: 2006 DENTSPLY International.
Interim Denture Interim Complete Dental Prosthesis Clinical Steps
Interim Denture Interim Complete Dental Prosthesis Clinical Steps Diagnostic Appointment Comprehensive Exam Extra oral Intra oral Address: Main complaint Esthetic concerns Other concerns Discuss (if present)
LEARN FROM A LEADER. Intensive, hands-on training that will prepare you to confidently fabricate the appliances you want.
from professionals like, one of the country s most experienced Guide to Orthodontic s... A Comprehensive Resource from Theory to. Brian also has been involved in many patents in the dental field. 2011
LABORATORY PROCEDURES, STEP BY STEP
LABORATORY PROCEDURES, STEP BY STEP BY TECHNICIANS FOR TECHNICIANS Eclipse Laboratory Procedures, Step by Step* Dentures with cast-metal frameworks Combination dentures Complete dentures Splints Drilling
Lect. 14 Prosthodontics Dr. Osama
Lect. 14 Prosthodontics Dr. Osama Principles of Removable Partial Denture Design Difference in Prosthesis Support and Influence on Design: For a tooth-supported prosthesis, the movement potential is less
Lucitone HIPA High Impact Pourable Acrylic Denture Base. The Pour with More
High Impact able Acrylic Denture Base The with More Build a Lab that Keeps Your Business Profitable. There is more pressure on labs than ever before. Expedited timelines and product constraints make it
MINIMAL INTERVENTION DENTISTRY THE PENN COMPOSITE STENT
SCD Case Study MINIMAL INTERVENTION DENTISTRY THE PENN COMPOSITE STENT The Penn Composite Stent is a treatment technique following the principles of Minimal Intervention Dentistry. What is Minimal Intervention
3D Printing Dentures. Dental Application Print Guide
Dental Application Print Guide 3D Printing Dentures Denture Base Resin is a highly accurate material specifically formulated for the creation of custom denture bases of all types. Production capabilities
TECHNICAL DATASHEET POUR TYPE ACRYLIC RESIN PDFTPT-082
TCHNICAL DATASHT POUR TYP ACRYLIC RSIN 1 PRODUCT OVRVIW Methacrylate polymers have enjoyed great popularity in dentistry because they are easily processed by using relatively simple techniques; they have
TRANSFER OF THE FUNCTIONALISED TEMPORARY transfer of the functionalized temporary from the oral cavity to the verticulator
TRANSFER OF THE FUNCTIONALISED TEMPORARY transfer of the functionalized temporary from the oral cavity to the verticulator What you need for this working: EQUIPMENT 10-0010 VERTYS SPLIT CAST & GUM 10-401
For the Perfect Class V and All Cervical Area Gingival Margins when Placing Direct Composites, Create an Injection Molding Matrix
Cronicon OPEN ACCESS EC DENTAL SCIENCE Case Report For the Perfect Class V and All Cervical Area Gingival Margins when Placing Direct Composites, Create an Injection Molding Paul C Belvedere* Adjunct Professor,
UDELL DENTAL LABORATORY Instructions for Use AND ERA-RV
STERN ERA AND ERA-RV Summary Extracoronal semi-precision attachment. Universal hinge with vertical resiliency. Nylon male, plastic pattern female. Female is waxed into the pattern of the abutment restoration
The Hanau Modular Articulator System 194 Fixed 11 cm width, adjustable Radial-Shift Guidances. Illustrated Instruction Manual
The Hanau Modular Articulator System 194 Fixed 11 cm width, adjustable Radial-Shift Guidances Illustrated Instruction Manual A Study Case for Occlusal Analysis This instruction manual illustrates the
ProAir Clear 2 Pack FOR PROFESSIONAL USE ONLY
Description The Lesonal ProAir Clear Pack Fast or Slow Clear is an acrylic urethane clearcoat for use over Lesonal Basecoat SB or Lesonal WB and intended for applications in cross flow and air-dry conditions.
VITA Akzent stands for a concept which replaces the previous generation of stains and thus enables the dental technician to achieve even more natural
for natural surface colour effects Date of issue: 08-08 Teeth Veneering Materials Vita System Service 3D - Master Equipment All-Ceramics stands for a concept which replaces the previous generation of stains
Removable Prosthodontics. Complete Denture Procedures for a Team Approach in the Home
Department of General Dentistry Division of Removable Prosthodontics Complete Denture Procedures for a Team Approach in the Home For Competency #9 1 Rev. April 2010 Ronni A. Schnell, D.M.D., M.A.G.D. and
Element-Z Screw-Retained Hybrid
Element-Z Screw-Retained Hybrid Implant-Level Restoration Step-by-Step Restorative Protocol The Element-Z Screw-Retained Hybrid offers a fixed, all-ceramic implant solution for edentulous patients desiring
Benefits of CBCT in Implant Planning
10.5005/jp-journals-10012-1032 CLINICAL SCIENCE 1 Gregori M Kurtzman, 2 Douglas F Dompkowski 1 Private General Practice in Silver Spring, Maryland, USA 2 Private Periodontal Practice in Bethesda, Maryland,
Amaris BeAuTy COmPOse it!
Beauty Compose it! Natural elegance Two simple steps layers like in nature brilliant results Easy to learn For several decades dentists have used an industry standard designed to facilitate communication
Removable Prosthodontics. Complete Denture Procedures for a Team Approach
Department of General Dentistry Division of Removable Prosthodontics Complete Denture Procedures for a Team Approach For Competency #9 1 Rev. April 2010 Ronni A. Schnell, D.M.D., M.A.G.D. Complete Denture
RELINING AND REBASING
RELINING AND REBASING Relining: The process used to resurface the tissue side of a denture with new material layer, thus producing an accurate adaptation to the denture foundation area. Rebasing: The laboratory
P r o t e mp 4 Temporisation Material
P r o t e mp 4 Temporisation Material Clinical case studies from around the world 3M ESPE Protemp 4 Temporisation Material is the first bis-acrylic material to include a new generation of sophisticated
Reimagine dentures. Revitalize your lab.
Digital Dentures Reimagine dentures. Revitalize your lab. There has never been a better time to go digital. The demand for dentures is growing, while the overall number of labs continues to decline. This
Accu-Dent. impression system. Procedural guide. System 2 TM. For removable dentate impressions
Accu-Dent impression system System 2 TM Procedural guide System 2 TM For removable dentate impressions The Complete System 2 TM Accu-Dent s System 2 is designed for partials, immediate dentures, orthodontics,
Contents. Section I WHY
Contents Section I WHY 1 Ergonomics and the Dental Microscope - 3 4 Surveys document significant ergonomic risk factors 8 Ergonomics and the Microscope 8 Positioning your Chair 9 Positioning the Patient
Frequent use for the preparation of prosthetic products
laboratory use Frequent use for the preparation of prosthetic products Silicones gain more and more use for the preparation of prosthetic products. ERGAMIX addition silicone (polyvinylsiloxane) and ERGASIL
primosplint Instruction Manual Light cured composite rods, MMA- and peroxide free
primosplint Instruction Manual Light cured composite rods, MMA- and peroxide free Especially developed for the production of function - therapy bite splints and more patent no.: 102 24 002 the product