Smll Tool Instruments n t Mngement igimti Cliper igimti Height Gges iner Height epth Gges SuperCliper ABSOUTE Coolnt Proof Cliper ABSOUTE igimti Cliper INEX Cliper SuperCliper -2 ABSOUTE Solr Cliper -3 ABSOUTE Coolnt Proof Cliper -4 ABSOUTE igimti Cliper -6 Vernier Cliper -8 ABSOUTE igimti & Vernier Cliper -12 ABSOUTE igimti Cliper -13 il Cliper -14 ABSOUTE Coolnt Proof Cron Fier Cliper -15 Vernier Cliper (Ni Style Jws) -18 ong Jw Vernier Cliper -19 Offset Cliper -20 Offset Centerline Cliper -21 ABSOUTE Bk-Jw Centerline Cliper -22 Point Cliper -23 Ble Type Cliper -24 Nek Cliper -25 ABSOUTE Insie Cliper -26 Tue Thikness Cliper -28 Hook Type Vernier Cliper -29 Swivel Vernier Cliper -29 ABSOUTE ow Fore Cliper -30 ABSOUTE Snp Cliper -30 Sriing Cliper -31 Plsti Cliper -32 Height Gges Heightmti -33 igimti Height Gge -34 ABSOUTE igimti Height Gge -36 il Height Gge -38 Vernier Height Gge -40 CERA Cliper Cheker -42 Crie-tippe Srier -43 Optionl Aessories -43 iner Height iner Height -44 QM-Height -46 epth Gges epth Mirometer -48 epth Miro Cheker -49 ABSOUTE igimti epth Gge -50 Vernier epth Gge -51 epth Gge -52 il epth Gge -53 Extension Bses -53 ABSOUTE igimti/il epth Gge -54 Tire Tre epth Gge -56 epth Bse Atthment -56 ABSOUTE igimti Offset Cliper igimti Height Gge -1
SuperCliper SERIES 500 No ttery or origin reset neee for IP67 igitl liper With no nnoying origin restortion neessry, mesurement n e strte ny time n there is no restrition on operting spee. Insuffiient illumintion stte Worl s unique* solr-powere SuperCliper tht is eo-frienly with no ttery *Aoring to Mitutoyo reserh in Jnury, 2005 The impt resistne of the isply unit hs een inrese for improve usility in workshop onitions. IP67 protetion ssures wterproof reliility. This SuperCliper uses omponents tht o not ontin hrmful sustnes n is omptile with RoHS iretives. (Refer to the pge VIII for etils.) 0000006683 Suffiient illumintion stte 16.78mm No nee for orgin set up High qulity guie surfe finish for smooth slier movement Conventionl SuperCliper iretion of the length iretion of the length R: 0.126µm R: 0.07µm Tehnil t Aury: ±0.02mm (exluing quntizing error) Resolution: 0.01mm or.0005"/0.01mm Repetility: 0.01mm isply: C Sle type: ABSOUTE eletromgneti liner enoer Mx. response spee: Unlimite Bttery: Solr ttery* ust/wter protetion level: IP67 *Cn e use ontinuously ove 60lux mient illumintion. Funtions Origin-set, inh/mm onversion (inh/mm moels) Alrm: Counting vlue omposition error 500-774 Optionl Aessories 05CZA624: SPC le with t swith (1m) 05CZA625: SPC le with t swith (2m) 02AZ790A: SPC le for U-WAVE w/ t swith (160mm) Rnge Orer No. Remrks 0-150mm 500-776 with t output 0-150mm 500-774 w/o t output 0-200mm 500-777 with t output 0-200mm 500-775 w/o t output Inh/ Rnge Orer No. Remrks 0-6" 500-786 with t output 0-6" 500-784 w/o t output 0-8" 500-787 with t output 0-8" 500-785 w/o t output IP67 protetion level evel 6: ust-tight No ingress of ust. evel 7: Protete ginst the effets of temporry immersion in wter. Ingress of wter in quntities using hrmful effets shll not e possile when the enlosure is temporrily immerse 1 meter in wter uner stnrize onitions of pressure n time (30 min.). 1m IMENSIONS Aout the hrge funtion (SuperCliper) The minimum illumintion require in the unhrge stte is 60lux. As shown in the tle JIS Z 9110 Artifiil Illumintion Intensity Stnr, this SuperCliper n e use with onfiene in norml work environment. Rnge 0-150mm/0-6 233 21 16.5 40 16 0-200mm/0-8 290 24.5 20 50 16 Jw thikness: 3.5mm The hrge funtion llows the opertor to use this SuperCliper without interrupting work even if the mient illumintion is temporrily insuffiient. In the fully hrge stte this SuperCliper n operte for pproximtely n hour in n environment of 50lux illumintion (less thn the minimum neessry illumintion intensity). The time neessry for full hrge iffers, epening on the hrging onitions. If this SuperCliper is left unuse in n illumintion of 500 lux (usul for mnufturing environments), it tkes pproximtely one hour to reh full hrge. -2
ABSOUTE Solr Cliper SERIES 500 No ttery or origin reset neee Mitutoyo's Asolute Solr igimti Cliper retins its origin point even if the isply turns off for the entire life of the liper. At 60 ux n ove the ABSOUTE solr liper is turne on rey to strt mesurement. No more repete zero setting use y shortge of light intensity. Hr-ote solr pnel for sfe opertion. No fer of overspee errors. High qulity guie surfe finish for smooth slier movement Conventionl ABSOUTE Solr Cliper Sliing iretion R: 0.126µm Sliing iretion R: 0.071µm Tehnil t Aury: ±0.02mm (exluing quntizing error) Resolution: 0.01mm or.0005"/0.01mm Repetility: 0.01mm isply: C Sle type*: ABSOUTE eletrostti liner enoer Mx. response spee: Unlimite Bttery: Solr ttery* *Cn e use ontinuously ove 60lux mient illumintion. Funtions Origin-set, t hol, t output, inh/mm onversion (inh/ mm moels) Alrm: Counting vlue omposition error Optionl Aessories 959143: t hol unit 959149: SPC le with t swith (1m) 959150: SPC le with t swith (2m) 02AZ790A: SPC le for U-WAVE w/ t swith (160mm) Rnge Orer No. epth r Fine justment 0-100mm 500-443 ø1.9mm ro with thum roller 0-100mm 500-453* ø1.9mm ro with thum roller 0-150mm 500-444 Ble with thum roller 0-150mm 500-454* Ble with thum roller 0-200mm 500-445 Ble with thum roller 0-200mm 500-455* Ble with thum roller *without SPC t output Inh/ Rnge Orer No. epth r Fine justment 0-4" 500-463 ø3/40" ro with thum roller 0-4" 500-473* ø3/40" ro with thum roller 0-6" 500-464 Ble with thum roller 0-6" 500-474* Ble with thum roller 0-8" 500-465 Ble with thum roller 0-8" 500-475* Ble with thum roller *without SPC t output 500-444 IMENSIONS 16 Rnge 0-100mm/0-4 182 40 21 16.5 0-150mm/0-6 233 40 21 16.5 0-200mm/0-8 290 50 24.5 20-3
ABSOUTE Coolnt Proof Cliper SERIES 500 with ust/wter Protetion Conforming to IP67 evel Cn e use in workshop onitions expose to oolnt, wter, ust or oil. Esy to use no nee to wipe or len the sle. Avne esign styling. Inorportes solute mesurement system. Automti power-on/off. t output funtion. High qulity guie surfe finish for smooth slier movement Conventionl ABSOUTE Coolnt Proof Cliper Sliing iretion Sliing iretion R: 0.126µm R: 0.071µm 500-712-10 500-752-10 500-763-10 Built-in ABS (solute) sle mens tht these lipers re rey to use immeitely fter poweron without origin resetting. It s s esy s vernier liper mesurements. Tehnil t Aury: ±0.02mm ( 200mm), ±0.03mm (>200mm) (exluing quntizing error) Resolution: 0.01mm or.0005"/0.01mm Repetility: 0.01mm isply: C Sle type: ABSOUTE eletromgneti liner enoer Mx. response spee: Unlimite Bttery: SR44 (1 p.), 938882 Bttery life: Approx. 3 yers uner norml use (1 yer: over 300mm moels) ust/wter protetion level: IP67 Power OFF 16.38 Power ON No origin resetting Funtions Origin-set, Zero-setting, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Certifite of inspetion Mesurement t output funtion is ville with wterresistnt SPC le. Optionl Aessories 05CZA624: SPC le with t swith (1m) 05CZA625: SPC le with t swith (2m) 02AZ790A: SPC le for U-WAVE w/ t swith (160mm) 05CZA624-4
Air lekge etetion system use for wter-proof testing Generlly, ir lekge tests re performe to evlute wter resistne. Testing egins y pling mesuring tool into the psule. Next, ir t the require test pressure is supplie to the psule n the mster psule, then the vlves re lose. If none of the ir in the psule seeps into the mesuring tool, the psule s ir pressure will remin equl to tht in the mster, n the ifferentil pressure guge will ontinue to point to the enter. However, if some ir oes seep into the mesuring tool, it will rete n ir pressure ifferene tht will e inite y the ifferentil pressure guge. Thus, etetion of ir pressure ifferenes is use s riterion for juging lekge. Every single unit of ABS Coolnt Proof liper n Coolnt Proof mirometer is teste this wy to help ensure prout qulity. Cpsule Vlve ifferentil pressure guge Air Vlve Mster Rnge Orer No. epth r Fine justment Remrks 0-150mm 500-702-10* Ble with thum roller 0-150mm 500-712-10 Ble with thum roller 0-150mm 500-706-11* Ble 0-150mm 500-716-11 Ble 0-150mm 500-709-11* ø1.9mm ro 0-150mm 500-719-10 ø1.9mm ro with thum roller 0-150mm 500-721-10 Ble with thum roller Crie-tippe jws for outsie mesurement 0-150mm 500-723-10 Ble with thum roller Crie-tippe jws for outsie n insie mesurement 0-150mm 500-727-11 Ble Crie-tippe jws for outsie n insie mesurement 0-200mm 500-703-10* Ble with thum roller 0-200mm 500-713-10 Ble with thum roller 0-200mm 500-707-11* Ble 0-200mm 500-717-11 Ble 0-200mm 500-722-10 Ble with thum roller Crie-tippe jws for outsie mesurement 0-200mm 500-724-10 Ble with thum roller Crie-tippe jws for outsie n insie mesurement 0-200mm 500-728-11 Ble Crie-tippe jws for outsie n insie mesurement 0-300mm 500-714-10 Ble with thum roller 0-300mm 500-718-11 Ble 0-300mm 500-704-10* Ble with thum roller 0-300mm 500-708-11* Ble *without SPC t output IP66 protetion level evel 6: ust-tight No ingress of ust. evel 6: Protete ginst powerful wter jets. Wter projete in powerful jets* ginst the enlosure from ny iretion shll hve no hrmful effets. *Size of iret jets: 12.5 mm (inner imeter) nozzle emitting 100 kp jet of wter t 100 liters per minute for t lest 3 minutes from istne of pprox. 3 meters. Inh/ Rnge Orer No. epth r Fine justment Remrks 0-6" 500-752-10* Ble with thum roller 0-6" 500-762-10 Ble with thum roller 0-6" 500-768-10* ø3/40 ro with thum roller 0-6" 500-769-10 ø3/40 ro with thum roller 0-6" 500-731-10* Ble with thum roller Crie-tippe jws for outsie mesurement 0-6" 500-735-10 Ble with thum roller Crie-tippe jws for outsie mesurement 0-6" 500-733-10* Ble with thum roller Crie-tippe jws for outsie n insie mesurement 0-6" 500-737-10 Ble with thum roller Crie-tippe jws outsie n insie mesurement 0-8" 500-753-10* Ble with thum roller 0-8" 500-763-10 Ble with thum roller 0-8" 500-732-10* Ble with thum roller Crie-tippe jws for outsie mesurement 0-8" 500-736-10 Ble with thum roller Crie-tippe jws for outsie mesurement 0-8" 500-734-10* Ble with thum roller Crie-tippe jws for outsie n insie mesurement 0-8" 500-738-10 Ble with thum roller Crie-tippe jws for outsie n insie mesurement 0-12" 500-764-10 Ble with thum roller 0-12" 500-754-10* Ble with thum roller *without SPC t output IP67 protetion level evel 6: ust-tight No ingress of ust. evel 7: Protete ginst the effets of temporry immersion in wter. Ingress of wter in quntities using hrmful effets shll not e possile when the enlosure is temporrily immerse 1 meter in wter uner stnrize onitions of pressure n time (30 min.). 1m IMENSIONS Rnge 0-150mm/0-6 233 40 21 16.5 16 0-200mm/0-8 290 50 24.5 20 16 0-300mm/0-12 404 64 27.5 21.8 20-5
ABSOUTE igimti Cliper SERIES 500 with Exlusive ABSOUTE Enoer Tehnology Mitutoyo's solute igimti Cliper is the next genertion of eletroni lipers. It keeps trk of its origin point one set. Whenever turne on, the lrge C sreen isplys the tul slier position rey to strt mesurement. No more repete zero setting is neessry with solute enoer tehnology s well s no no more onerns out overspee errors. High qulity guie surfe finish for smooth slier movement Conventionl ABS igimti Cliper rge n ler C reout. The ZERO/ABS key llows the isply to e Zero-Set t ny slier position long the sle for omprison mesurements. This swith will lso llow return to the solute (ABS) moe n isply of the true position from the origin (usully jwslose point). t Hol Unit (959143) is optionl. Crie-tippe jw type lipers re lso ville. *Up to 300mm/12 rnge moels. iretion of the length R: 0.126µm iretion of the length R: 0.071µm 500-150-20 IMENSIONS 500-181-20 Tehnil t Aury: ±0.02mm ( 200mm), ±0.03mm ( 300mm) ±0.05mm ( 600mm), ±0.07mm ( 1000mm) (exluing quntizing error) Resolution: 0.01mm or.0005"/0.01mm Repetility: 0.01mm isply: C Sle type*: ABSOUTE eletrostti liner enoer Mx. response spee: Unlimite Bttery: SR44 (1 p.), 938882 Bttery life: Approx. 3.5 yers uner norml use Funtions Origin-set, Zero-setting, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Rnge 0-100mm/0-4 182 40 21 16.5 16 0-150mm/0-6 233 40 21 16.5 16 0-200mm/0-8 290 50 24.5 20 16 0-300mm/0-12 404 64 27.5 22 20 Optionl Aessories 959143: t hol unit 959149: SPC le with t swith (1m) 959150: SPC le with t swith (2m) 02AZ790C: SPC le for U-WAVE w/ t swith (160mm) 959143 959149 Rnge 0-450mm/0-18 630 90 47 38 25 0-600mm/0-24 780 90 47 38 25 0-1000mm/0-40 1240 130 61 50 32-6
Rnge Orer No. epth r Fine justment Remrks 0-100mm 500-150-20 ø1.9mm ro with thum roller 0-100mm 500-180-20* ø1.9mm ro 0-150mm 500-151-20 Ble with thum roller 0-150mm 500-154-20 Ble with thum roller Crie-tippe jws for outsie mesurement 0-150mm 500-155-20 Ble with thum roller Crie-tippe jws for outsie n insie mesurement 0-150mm 500-158-20 ø1.9mm ro with thum roller 0-150mm 500-181-20* Ble 0-200mm 500-152-20 Ble with thum roller 0-200mm 500-156-20 Ble with thum roller Crie-tippe jws for outsie mesurement 0-200mm 500-157-20 Ble with thum roller Crie-tippe jws for outsie n insie mesurement 0-200mm 500-182-20* Ble 0-300mm 500-153 Ble with thum roller 0-450mm 500-500-10 0-600mm 500-501-10 0-1000mm 500-502-10 *without SPC t output Inh/ Rnge Orer No. epth r Fine justment Remrks 0-4" 500-170-20 ø3/40" ro with thum roller 0-4" 500-195-20* ø3/40" ro with thum roller 0-6" 500-171-20 Ble with thum roller 0-6" 500-174-20 Ble with thum roller Crie-tippe jws for outsie mesurement 0-6" 500-175-20 Ble with thum roller Crie-tippe jws for outsie n insie mesurement 0-6" 500-178-20 ø3/40" ro with thum roller 0-6" 500-196-20* Ble with thum roller 0-6" 500-159-20* Ble with thum roller Crie-tippe jws for outsie mesurement 0-6" 500-160-20* Ble with thum roller Crie-tippe jws for outsie n insie mesurement 0-8" 500-172-20 Ble with thum roller 0-8" 500-176-20 Ble with thum roller Crie-tippe jws for outsie mesurement 0-8" 500-177-20 Ble with thum roller Crie-tippe jws for outsie n insie mesurement 0-8" 500-197-20* Ble with thum roller 0-8" 500-163-20* Ble with thum roller Crie-tippe jws for outsie mesurement 0-8" 500-164-20* Ble with thum roller Crie-tippe jws for outsie n insie mesurement 0-12" 500-173 Ble with thum roller 0-12" 500-167 Ble with thum roller Crie-tippe jws for outsie mesurement 0-12" 500-168 Ble with thum roller Crie-tippe jws for outsie n insie mesurement 0-12" 500-193* Ble with thum roller 0-12" 500-165* Ble Crie-tippe jws for outsie mesurement 0-12" 500-166* Ble Crie-tippe jws for outsie n insie mesurement 0-18" 500-505-10 0-24" 500-506-10 0-40" 500-507-10 *without SPC t output 500-502-10 500-501-10 500-500-10-7
Vernier Cliper SERIES 530 Stnr moel Plin n si esign. Cn mesure outsie n insie imeter (O n I), epth, n steps. The smll vernier fe ngle (14 ) provies esy reing. ifferent reing sles on vernier. (metri/inh n inh moels only) Clmping srew top the slier. Crie-tippe jw type lipers re lso ville. 14 Tehnil t Aury: ±0.05mm ( 200mm), ±0.08mm ( 300mm) ±0.10mm ( 600mm), ±0.15mm ( 1000mm) High ury type: ±0.03mm ( 200mm), ±0.04mm ( 300mm) Grution: 0.05mm, 0.05mm (1/128 ) or.001 (1/128 ) High ury type: 0.02mm or 0.02mm (.001 ) 530-101 530-100 Crie-tippe Crie-tippe jw type Roun epth r type IMENSIONS Rnge 0-100mm 182 40 21 17 16 0-150mm 229 40 21 17 16 0-200mm 288 50 24.5 20.5 16 0-300mm 404 64 27.5 22 20 0-600mm 780 90 47 38 25 0-1000mm 1240 130 60 50 32-8
Mesurement Applitions O mesurement I mesurement Rnge Orer No. epth r Remrks 0-100mm 530-100 ø1.9mm ro 0-150mm 530-102 ø1.9mm ro 0-150mm 530-101 Ble 0-150mm 530-320 Ble Crie-tippe jws for outsie mesurement 0-150mm 530-335 Ble Crie-tippe jws for outsie n insie mesurement 0-150mm 530-122* Ble High ury moel: ±0.03mm 0-200mm 530-108 Ble 0-200mm 530-321 Ble Crie-tippe jws for outsie mesurement 0-200mm 530-123* Ble High ury moel: ±0.03mm 0-300mm 530-109 Ble 0-300mm 530-322 Ble Crie-tippe jws for outsie mesurement 0-300mm 530-124* Ble High ury moel: ±0.04mm 0-600mm 530-501 0-1000mm 530-502 *Grution: 0.02mm /Inh Rnge Orer No. epth r Inh grution Remrks 0-150mm 530-104 Ble 1/128" 0-150mm 530-316 Ble 1/128" Clmping srew elow the slier 0-150mm 530-312* Ble.001" High ury moel: ±0.03mm 0-200mm 530-114 Ble 1/128" 0-200mm 530-118* Ble.001" High ury moel: ±0.03mm 0-300mm 530-115 Ble 1/128" 0-300mm 530-119* Ble.001" High ury moel: ±0.04mm *Grution: 0.02mm Inh with metri/inh oule sle with inh/inh oule sle Rnge Orer No. epth r Inh grution Remrks 0-6" 530-105 Ble 1/128" 0-8" 530-116 Ble 1/128" Step mesurement Vernier Cliper SERIES 536 Prllx-Free Type Prllx-free vernier sles for esy n positive mesurement. Cn mesure outsie n insie imeter (O n I), epth, n steps. With lmping srew top the slier. Speil moel (Series 536) is esigne for left-hne users. epth mesurement Rnge Orer No. epth r Remrks 0-150mm 536-310 Ble eft-hne type 536-310 Tehnil t Aury: ±0.05mm Grution: 0.05mm IMENSIONS Rnge 0-150mm 229 40 21 16.5 16-9
Vernier Cliper SERIES 532 with Fine Ajustment Fine-justment is slier positioning. Cn mesure outsie n insie imeter (O n I), epth, n steps. 532-101 Tehnil t Aury: ±0.03mm ( 180mm), ±0.04mm ( 280mm) Grution: 0.02mm, 0.02mm (.001 ) or.001 (1/128 ) Rnge Orer No. epth r Remrks 0-130mm 532-101 Ble with fine justment 0-180mm 532-102 Ble with fine justment 0-280mm 532-103 Ble with fine justment /Inh with metri/inh oule sle Rnge Orer No. epth r Inh grution Remrks 0-130mm 532-119 Ble.001" with fine justment 0-180mm 532-120 Ble.001" with fine justment 0-280mm 532-121 Ble.001" with fine justment IMENSIONS Rnge 0-130mm/0-5 229 40 21.5 17 16 0-180mm/0-7 288 50 25 20.5 16 0-280mm/0-11 404 64 27.5 22 20-10
Vernier Cliper SERIES 531 with Thum Clmp Tehnil t Aury: Refer to the list of speifitions. Grution: 0.05mm, 0.05mm (1/128 ) or.001 (1/128 ) High ury type: 0.02mm or 0.02mm (.001 ) The slier moves only when the springloe thum grip is epresse. Thum grip Cn mesure outsie n insie imeter (O n I), epth, n steps. 531-101 IMENSIONS 53.5 epth r Remrks 0-150mm 531-101 ±0.05mm Ble 0-200mm 531-102 ±0.05mm Ble 0-300mm 531-103 ±0.08mm Ble 30 *Grution: 0.02mm Rnge 0-150mm/0-6 229 40 21.5 17 16 0-200mm/0-8 288 50 25 20.5 16 0-300mm/0-12 403 64 27.5 22 20 /Inh with metri/inh oule sle epth r Inh Remrks grution 0-150mm 531-122 ±0.05mm Ble 1/128" with inh/mm onversion lel 0-150mm 531-128* ±0.03mm Ble.001 High ury moel 0-200mm 531-108 ±0.05mm Ble 1/128" 0-200mm 531-129* ±0.03mm Ble.001 High ury moel 0-300mm 531-109 ±0.08mm Ble 1/128" 0-300mm 531-112* ±0.04mm Ble.001 High ury moel *Grution: 0.02mm Vernier Cliper SERIES 522 Prllx-Free Type Tehnil t Aury: Refer to the list of speifitions. Grution: 0.05mm (1/128 ) High ury type: 0.02mm (.001 ) The min n vernier sles re flush-fitte to eliminte prllx errors euse of the imon-shpe (otgonl) ross setion of the min sle. Cn mesure outsie n insie imeter (O n I), epth, n steps. With loking srew elow the slier. 522-602 IMENSIONS 22 17 229 epth r Remrks 0-150mm 522-600 ±0.05mm Ble 0-150mm 522-606* ±0.03mm Ble High ury moel 15 *Grution: 0.02mm 40.5 /Inh with metri/inh oule sle epth r Inh resolution Remrks 0-150mm 522-601 ±0.05mm Ble 1/128" 0-150mm 522-602* ±0.03mm Ble.001 High ury moel *Grution: 0.02mm -11
ABSOUTE igimti & Vernier Cliper SERIES 550, 160 with Ni Style Jws The roune fes of the jws re iel for urte insie imeter (I) mesurement. Insie n outsie mesurements n e re iretly from the upper n lower vernier sles (Series 160). Fine-justment type is ville (Series 160). Prllx-free vernier sle type is ville for esy n positive mesurement (Series 160). SPC output (Series 550). Min sle grutions Prllel sle fes Vernier grutions 550-301-10 Rnge* Orer No. Aury Remrks 0-200mm (10-210mm) 550-301-10 ±0.03mm IP67 0-300mm (10-310mm) 550-331-10 ±0.04mm IP67, with offset/preset funtion for esy insie mesurement 0-450mm (20-470mm) 550-203-10 ±0.05mm 0-600mm (20-620mm) 550-205-10 ±0.05mm 0-1000mm (20-1020mm) 550-207-10 ±0.07mm *( ): Insie mesurement Inh/ Rnge* Orer No. Aury Remrks 0-8" (.4-8.4 ) 550-311-10 ±.0015" IP67 0-12" (.4-12.4 ) 550-341-10 ±.002" IP67, with offset/preset funtion for esy insie mesurement 0-18" (.5-18.5 ) 550-223-10 ±.002" 0-24" (.5-24.5 ) 550-225-10 ±.002" 0-40" (1-41 ) 550-227-10 ±.003" *( ): Insie mesurement Rnge* Orer No. Aury Remrks 0 (20) - 450mm 160-130 ±0.10mm 0 (20) - 600mm 160-131 ±0.10mm 0 (20) - 1000mm 160-132 ±0.15mm *( ): Minimum imension in insie mesurement IMENSIONS igitl moel igitl moel with metri/metri oule sle 160-130 Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error for igitl moels) Resolution*: 0.01mm or.0005"/0.01mm Grution**: 0.02mm isply*: C Sle type*: ABSOUTE eletrostti liner enoer Mx. response spee*: Unlimite Bttery*: SR44 (1 p.), 938882 Bttery life*: Approx. 3 yers uner norml use (1 yer: 300mm moels) (3.5 yers: over 300mm moels) ust/wter protetion level*: IP67 (moels up to 300mm) *igitl moels **Anlog moels Funtions of igitl Moel Origin-set, Zero-setting, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Optionl Aessories for igitl Moel 05CZA624: SPC le with t swith (1m)* 05CZA625: SPC le with t swith (2m)* 02AZ790A: SPC le for U-WAVE w/ t swith (160mm)* 959143: t hol unit 959149: SPC le with t swith (1m) 959150: SPC le with t swith (2m) 02AZ790C: SPC le for U-WAVE w/ t swith (160mm) *For IP67 moels (up to 300mm) Series 550 / 160 Series 551 / 533 R Rnge R 0-200mm 60 40.5 8 5 0-300mm 75 50.5 12 5 0-450mm 100 65 18 10 0-600mm 100 65 18 10 0-1000mm 140 95 24 10 R Rnge R 0-200mm 60 43 8 30 5 0-300mm 90 68 10 40.1 5 0-450mm 150 115 15 56 10 0-600mm 150 115 15 56 10 0-1000mm 150 115 20 56 10 Roun surfe of jws for urte C mesurement -12
ABSOUTE igimti Cliper SERIES 551, 533 with Ni Style n Stnr Jws Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error for igitl moels) Resolution: 0.01mm or.0005"/0.01mm isply: C Sle type: ABSOUTE eletrostti liner enoer Mx. response spee: Unlimite Bttery: SR44 (1 p.), 938882 Bttery life: Approx. 3 yers uner norml use (1 yer: 300mm moels) (3.5 yers: over 300mm moels) ust/wter protetion level: IP67 (moels up to 300mm) Funtions of igitl Moel Origin-set, Zero-setting, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error The roune fes of the jws re iel for urte insie imeter (I) mesurement. SPC output. (Series 551) Insie n outsie mesurements n e re iretly from the upper n lower vernier sles (Series 533). 551-311-10 533-404 Optionl Aessories for igitl Moel 05CZA624: SPC le with t swith (1m)* 05CZA625: SPC le with t swith (2m)* 02AZ790A: SPC le for U-WAVE w/ t swith (160mm)* 959143: t hol unit 959149: SPC le with t swith (1m) 959150: SPC le with t swith (2m) 02AZ790C: SPC le for U-WAVE w/ t swith (160mm) *For IP67 moels (up to 300mm) Rnge* Orer No. Aury Remrks 0-200mm (10-210mm) 551-301-10 ±0.03mm IP67 0-300mm (10-310mm) 551-331-10 ±0.04mm IP67, with offset/preset funtion for esy insie mesurement 0-500mm (20-520mm) 551-204-10 ±0.06mm 0-750mm (20-770mm) 551-206-10 ±0.06mm 0-1000mm (20-1020mm) 551-207-10 ±0.07mm *( ): insie mesurement igitl moel Inh/ Rnge* Orer No. Aury Remrks 0-8" (.4-8.4 ) 551-311-10 ±.0015" IP67 0-12" (.4-12.4 ) 551-341-10 ±.002" IP67, with offset/preset funtion for esy insie mesurement 0-20" (.5-20.5 ) 551-224-10 ±.0025" 0-30" (.5-30.5 ) 551-226-10 ±.0025" 0-40" (1-41 ) 551-227-10 ±.003" *( ): insie mesurement igitl moel Roun surfe of jws for urte C mesurement Rnge* Orer No. Aury Remrks 0 (20) - 500mm 533-404 ±0.10mm 0 (20) - 750mm 533-405 ±0.12mm 0 (20) - 1000mm 533-406 ±0.15mm *( ): insie mesurement with metri/metri oule sle -13
il Cliper SERIES 505 Newly esigne il movement for ultr smooth sliing n high shok protetion. Titnium oting is pplie to the sliing surfes to enhne the urility (exept for 0-300mm n 0-12" moel). No wer over 100,000-time sliing test. Cn mesure outsie n insie imeter (O n I), epth, n steps. Clmping srew top the slier. Speil moels ville with rietippe outsie n insie jws. 505-671 505-681 505-673 IMENSIONS 505-683 Grution Remrks 0-100mm 505-680 ±0.015mm 0.01mm, 1mm/rev 0-150mm 505-671 / 505-683* ±0.03mm 0.02mm, 2mm/rev 0-150mm 505-707 ±0.03mm 0.02mm, 2mm/rev Crie-tippe jws for outsie mesurement 0-150mm 505-711 ±0.03mm 0.02mm, 2mm/rev Crie-tippe jws for outsie n insie mesurement 0-150mm 505-681 / 505-685* ±0.02mm 0.01mm, 1mm/rev 0-200mm 505-672 / 505-684* ±0.03mm 0.02mm, 2mm/rev 0-200mm 505-682 / 505-686* ±0.03mm 0.01mm, 1mm/rev 0-300mm 505-673 ±0.04mm 0.02mm, 2mm/rev *Silver over type Inh Grution Remrks 0-4" 505-674 ±.001".001",.1"/rev 0-6" 505-675 / 505-689* ±.001".001",.1"/rev 0-6" 505-708 ±.001".001",.1"/rev Crie-tippe jws for outsie mesurement 0-6" 505-712 ±.001".001",.1"/rev Crie-tippe jws for outsie n insie mesurement 0-8" 505-676 / 505-690* ±.002".001",.1"/rev 0-8" 505-709 ±.002".001",.1"/rev Crie-tippe jws for outsie mesurement 0-8" 505-713 ±.002".001",.1"/rev Crie-tippe jws for outsie n insie mesurement 0-12" 505-720 ±.002".001",.2"/rev 0-12" 505-677* ±.002".001",.1"/rev 0-12" 505-721 ±.002".001",.2"/rev Crie-tippe jws for outsie mesurement 0-12" 505-710* ±.002".001",.1"/rev Crie-tippe jws for outsie mesurement 0-12" 505-714* ±.002".001",.1"/rev Crie-tippe jws for outsie n insie mesurement *Silver over type Titnium oting Conventionl Wer: 0µm Wer: 4µm Tehnil t Aury: Refer to the list of speifitions. il reing: Refer to the list of speifitions. Rnge 0-100mm 180 40 21 16.5 16 0-150mm 231 40 21 16.5 16 0-200mm 288 50 24.5 20 16 0-300mm 403 64 27.5 22 20-14
ABSOUTE Coolnt Proof Cron Fier Cliper SERIES 552 with Interhngele Jws The rnge of pplitions n e expne y using interhngele jws (optionl). Quik n esy exhnging of jws ue to the unique lmping mehnism. (A pir of lmping wheels is stnr essory.) Provie with preset funtion for setting esire strting point, whih llows iret reout of offset mesurements. SPC t output. 552-182-10 with optionl interhngele jws Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error) Resolution: 0.01mm or.0005"/0.01mm isply: C Sle type: ABSOUTE eletromgneti liner enoer Mx. response spee: Unlimite Bttery: SR44 (1 p.), 938882 Bttery life: Approx. 5,000 hours in ontinuous use ust/wter protetion level: IP66 Stnr essory: Jw lmps (2 ps.), 05GZA033 0-450mm 552-181-10 ±0.04mm 0-600mm 552-182-10 ±0.04mm 0-1000mm 552-183-10 ±0.05mm 0-1500mm 552-184-10 ±0.09mm 0-2000mm 552-185-10 ±0.12mm Interhngele Jws (Optionl) Stnr type 9 Insie point type 5 9 Inh/ 0-18" 552-191-10 ±.002" 0-24" 552-192-10 ±.002" 0-40" 552-193-10 ±.002" 0-60" 552-194-10 ±.004" 0-80" 552-195-10 ±.005" Stnr Type Orer No. Components 07CZA056 Right (07CAA044), 28mm 30mm eft (07CAA045) (1.1") (1.2") 35 Insie Point Type Funtions Origin-set, Zero-setting, Presetting, Offsetting, t hol, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Optionl Aessories 05CZA624: SPC le with t swith (1m) 05CZA625: SPC le with t swith (2m) 02AZ790A: SPC le for U-WAVE w/ t swith (160mm) 0.5 Surfe Plte Type 4.5 9 30 Srier Type ø 60 Centerline Type ø1 ø 9 9 9 Orer No. Components 07CZA058 07CZA041 x 2ps. 25mm 50mm 07CZA059 07CZA048 x 2ps. 1" 2" Srier Type Orer No. Components 07CZA055 Right (07CZA042), 8mm 30mm eft (07CZA043) 07CZA061 Right (07CZA042), eft (07CZA049) 031" 1.2" Surfe Plte Type Orer No. 07CZA044 90mm (3.5") 28mm (1.1") Centerline Type Orer No. Components 07CZA057 07CZA039 x 2ps. 30mm 30mm 07CZA060 07CZA047 x 2ps. 1.2" 1.2" -15
ABSOUTE Coolnt Proof Cron Fier Cliper SERIES 552 ightweight igimti Clipers tht employ CFRP (Cron Fier Reinfore Plstis) in the em n jws. Highly urle n esy to hnle. The rnge of pplitions n e expne y using the optionl tthments. iret reout of insie mesurements from the C. (Offset vlue n e set esily y using the Offset key.) Preset funtion for setting esire strting point. SPC t output. Speil moel ville with ermi jws suitle for mesuring mgneti prouts. 552-314-10 552-155-10 552-151-10 Rnge* Orer No. (stnr / long jws / ermi jws) Aury (stnr / long jws / ermi jws) 0 (20) - 450mm 552-302-10 / 552-150-10 / 552-155-10 ±0.04mm / ±0.06mm / ±0.04mm 0 (20) - 600mm 552-303-10 / 552-151-10 / 552-156-10 ±0.04mm / ±0.06mm / ±0.04mm 0 (20) - 1000mm 552-304-10 / 552-152-10 ±0.05mm / ±0.07mm 0 (20) - 1500mm 552-305-10 / 552-153-10 ±0.09mm / ±0.11mm 0 (20) - 2000mm 552-306-10 / 552-154-10 ±0.12mm / ±0.14mm *( ): Minimum imension in insie mesurement Inh/ Rnge* Orer No. (stnr / long jws / ermi jws) Aury (stnr / long jws / ermi jws) 0 (.5 ) - 18" 552-312-10 / 552-160-10 / 552-165-10 ±.002" / ±.0025 / ±.002 0 (.5 ) - 24" 552-313-10 / 552-161-10 / 552-166-10 ±.002" / ±.0025 / ±.002 0 (1 ) - 40" 552-314-10 / 552-162-10 ±.002" / ±.003 0 (1 ) - 60" 552-315-10 / 552-163-10 ±.004" / ±.0045 0 (1 ) - 80" 552-316-10 / 552-164-10 ±.005" / ±.0055 *( ): Minimum imension in insie mesurement Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error) Resolution: 0.01mm or.0005"/0.01mm isply: C Sle type: ABSOUTE eletromgneti liner enoer Mx. response spee: Unlimite Bttery: SR44 (1 p.), 938882 Bttery life: Approx. 5,000 hours in ontinuous use ust/wter protetion level: IP66 Funtions Origin-set, Zero-setting, Presetting, Offsetting, t hol, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Optionl Aessories 05CZA624: SPC le with t swith (1m) 05CZA625: SPC le with t swith (2m) 02AZ790A: SPC le for U-WAVE w/ t swith (160mm) -16
IMENSION e Stnr moels Cermi jw moels ong jw moels Stnr moels, Cermi jw moels R10 f 8 f Rnge e f 0-450mm 640 100 18 41.2 91.8 25 10 (.25") 0-600mm 790 100 18 41.2 91.8 25 10 (.25") 0-1000mm 1230 150 24 62.8 113.8 32 10 (.5") 0-1500mm 1740 150 24 62.8 113.8 32 10 (.5") 0-2000mm 2250 150 24 62.8 113.8 32 10 (.5") ( ): inh/mm moels ong jw moels Rnge e f 0-450mm 680 200 24 89 91.8 25 10 (.25") 0-600mm 830 200 24 89 91.8 25 10 (.25") 0-1000mm 1280 200 24 110 113.8 32 10 (.5") 0-1500mm 1790 200 24 110 113.8 32 10 (.5") 0-2000mm 2300 200 24 110 113.8 32 10 (.5") ( ): inh/mm moels e Interhngele jw moels Interhngele jw moels Rnge e 0-450mm 640 41.2 91.8 25 0-600mm 790 41.2 91.8 25 0-1000mm 1230 62.8 113.8 32 0-1500mm 1740 62.8 113.8 32 0-2000mm 2250 62.8 113.8 32 ( ): inh/mm moels -17
f Vernier Cliper SERIES 160 with Ni Style Jws n Fine Ajustment The jws hve roun mesuring fes for urte insie imeter (I) mesurement. With fine justment (exepting 160-130/131/132/133/134). The single min sle moels feture n itionl (offset) vernier sle to enle insie mesurements to e re iretly. 160-131 160-101 Rnge* Orer No. Aury Grutions Remrks 0 (20) - 450mm 160-130 ±0.10mm 0.05mm without fine justment 0 (20) - 600mm 160-131 ±0.10mm 0.05mm without fine justment 0 (20) - 1000mm 160-132 ±0.15mm 0.05mm without fine justment 0 (20) - 1500mm 160-133 ±0.22mm 0.05mm without fine justment 0 (20) - 2000mm 160-134 ±0.28mm 0.05mm without fine justment *( ): Minimum imension in I mesurement with insie mesurement vernier sle Tehnil t Aury: Refer to the list of speifitions. Grution: Refer to the list of speifitions. Rnge* Orer No. Aury Grutions Remrks 0 (10) - 300mm 160-127 ±0.04mm 0.02mm 0 (20) - 450mm 160-128 ±0.05mm 0.02mm 0 (20) - 600mm 160-101 ±0.05mm 0.02mm 0 (20) - 1000mm 160-104 ±0.07mm 0.02mm 0 (20) - 1500mm 160-110 ±0.1mm 0.02mm 0 (20) - 2000mm 160-113 ±0.12mm 0.02mm *( ): Minimum imension in I mesurement with insie mesurement vernier sle /Inh Rnge* Orer No. Aury Grutions Remrks 0 (10) - 300mm 160-150 ±0.04mm 0.02mm/.001 +10mm/.394 to reing in insie mesurement 0 (20) - 450mm 160-151 ±0.05mm 0.02mm/.001 +20mm/.787 to reing in insie mesurement 0 (20) - 600mm 160-153 ±0.05mm 0.02mm/.001 +20mm/.787 to reing in insie mesurement 0 (20) - 1000mm 160-155 ±0.07mm 0.02mm/.001 +20mm/.787 to reing in insie mesurement 0 (20) - 1500mm 160-157 ±0.1mm 0.02mm/.001 +20mm/.787 to reing in insie mesurement 0 (20) - 2000mm 160-159 ±0.12mm 0.02mm/.001 +20mm/.787 to reing in insie mesurement *( ): Minimum imension in I mesurement Inh Rnge* Orer No. Aury Grutions Remrks 0 (.3 ) - 12" 160-124 ±.0015".001 0 (.5 ) - 18" 160-116 ±.002".001 0 (.5 ) - 24" 160-102 ±.002".001 0 (1 ) - 40" 160-105 ±.003".001 0 (1 ) - 60" 160-111 ±.004".001 0 (1 ) - 80" 160-114 ±.005".001 *( ): Minimum imension in I mesurement Inh/ Rnge* Orer No. Aury Grutions Remrks 0 (.3 ) - 12" 160-125 ±.0015".001 /0.02mm +.3 /7.62mm to reing in insie mesurement 0 (.5 ) - 18" 160-119 ±.002".001 /0.02mm +.5 /12.7mm to reing in insie mesurement 0 (.5 ) - 24" 160-103 ±.002".001 /0.02mm +.5 /12.7mm to reing in insie mesurement 0 (1 ) - 40" 160-106 ±.003".001 /0.02mm +1 /25.4mm to reing in insie mesurement 0 (1 ) - 60" 160-112 ±.004".001 /0.02mm +1 /25.4mm to reing in insie mesurement 0 (1 ) - 80" 160-115 ±.005".001 /0.02mm +1 /25.4mm to reing in insie mesurement *( ): Minimum imension in I mesurement with metri/inh oule sle with insie mesurement vernier sle with inh/metri oule sle IMENSIONS Roun-fe jws for urte I mesurement e R Rnge e f R 0-300mm 445 95 25 12 20 10 3.8 R5 0-450mm 630 125 100 18 25 14.8 6 R10 0-600mm 780 125 100 18 25 14.8 6 R10 0-1000mm 1240 172 140 24 32 17 10 R10 0-1500mm 1800 212 180 30 32 19 10 R10 0-2000mm 2300 220 180 30 40 23 12 R10-18
f ong Jw Vernier Cliper SERIES 534 ong jws for mesuring hr-to-reh workpiee fetures. 534-110 534-114 Tehnil t Aury: Refer to the list of speifitions. Grution: Refer to the list of speifitions. Rnge* Orer No. Aury Grution Remrks 0 (10) - 300mm 534-109 ±0.07mm 0.05mm without fine justment 0 (20) - 500mm 534-110 ±0.13mm 0.05mm without fine justment *( ): Minimum imension in insie mesurement IMENSIONS with insie mesurement vernier sle Rnge* Orer No. Aury Grution Remrks 0 (10) - 300mm 534-113 ±0.04mm 0.02mm 0 (20) - 500mm 534-114 ±0.06mm 0.02mm 0 (20) - 750mm 534-115 ±0.08mm 0.02mm 0 (20) - 1000mm 534-116 ±0.10mm 0.02mm *( ): Minimum imension in insie mesurement /Inh Rnge* Orer No. Aury Grution Remrks 0 (10) - 300mm 534-101 ±0.07mm 0.05mm/ 1/128 +10mm/.394 to reing in insie mesurement 0 (10) - 300mm 534-105 ±0.04mm 0.02mm/.001 +10mm/.394 to reing in insie mesurement 0 (20) - 500mm 534-102 ±0.13mm 0.05mm/ 1/128 +20mm/.787 to reing in insie mesurement 0 (20) - 500mm 534-106 ±0.06mm 0.02mm/.001 +20mm/.787 to reing in insie mesurement 0 (20) - 700mm 534-103 ±0.16mm 0.05mm/ 1/128 +20mm/.787 to reing in insie mesurement 0 (20) - 700mm 534-107 ±0.08mm 0.02mm/.001 +20mm/.787 to reing in insie mesurement 0 (20) - 1000mm 534-104 ±0.20mm 0.05mm/ 1/128 +20mm/.787 to reing in insie mesurement 0 (20) - 1000mm 534-108 ±0.10mm 0.02mm/.001 +20mm/.787 to reing in insie mesurement *( ): Minimum imension in insie mesurement Inh Rnge* Orer No. Aury Grution Remrks 0 (.3 ) - 12" 534-117 ±.002".001 0 (.8 ) - 20" 534-118 ±.003".001 0 (.8 ) - 30" 534-119 ±.004".001 0 (.8 ) - 40" 534-120 ±.004".001 *( ): Minimum imension in insie mesurement with insie mesurement vernier sle with metri/inh oule sle with insie mesurement vernier sle Roun-fe jws for urte I mesurement R e Rnge e f R 0-300mm 445 110 90 12 20 7 3.8 R5 0-500mm 682 225 200 18.5 25 12 6 R10 0-750mm 995 232 200 18.5 32 12 8 R10 0-1000mm 1230 232 200 18.5 32 12 8 R10-19
Offset Cliper SERIES 573, 536 ABSOUTE igimti n vernier type The em-mounte jw n e juste to filitte mesurement of steppe setions n hr-to-get-t workpiee fetures. With epth r. SPC t output (Series 573). 573-601 536-101 Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error for igitl moels) Resolution*: 0.01mm or.0005"/0.01mm Grution**: 0.05mm isply*: C Sle type*: ABSOUTE eletromgneti liner enoer Mx. response spee*: Unlimite Bttery*: SR44 (1 p.), 938882 Bttery life*: Approx. 3 yers uner norml use (1 yer: 300mm moel) ust/wter protetion level*: IP67 *igitl moels **Anlog moels igitl moel 0-150mm 573-601 ±0.02mm 0-150mm 573-611* ±0.02mm 0-200mm 573-602 ±0.02mm 0-200mm 573-612* ±0.02mm 0-300mm 573-604 ±0.03mm 0-300mm 573-614* ±0.03mm Inh/ igitl moel 0-6" 573-701 ±.001" 0-8" 573-702 ±.001" 0-12" 573-704 ±.0015" Funtions of igitl Moel Origin-set, Zero-setting, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Optionl Aessories for igitl Moel 05CZA624: SPC le with t swith (1m) 05CZA625: SPC le with t swith (2m) 02AZ790A: SPC le for U-WAVE w/ t swith (160mm) *Without thum roller 0-150mm 536-101 ±0.05mm 0-200mm 536-102 ±0.05mm 0-300mm 536-103 ±0.08mm IMENSIONS A B C Vernier moel igitl moel Rnge 0-150mm/0-6 95 10 40 30 0-200mm/0-8 95 10 50 38.5 0-300mm/0-12 135 15 64 51-20
t t Offset Centerline Cliper SERIES 536, 573 ABSOUTE igimti n vernier type Speilly esigne for hole enter-toenter mesurements on the sme, or offset, plnes. Cn lso mesure from n ege to hole enter. Hole imeter shoul e in the rnge 1.5mm - 10mm (.06" -.4"). SPC t output (Series 573). Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error for igitl moels) Resolution*: 0.01mm or.0005"/0.01mm Grution**: 0.05mm isply*: C Sle type*: ABSOUTE eletromgneti liner enoer Mx. response spee*: Unlimite Bttery*: SR44 (1 p.), 938882 Bttery life*: Approx. 3 yers uner norml use (1 yer: 310mm moel) ust/wter protetion level*: IP67 *igitl moels **Anlog moels 573-605 Funtions of igitl Moel Origin-set, Zero-setting, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Optionl Aessories for igitl Moel 05CZA624: SPC le with t swith (1m) 05CZA625: SPC le with t swith (2m) 02AZ790A: SPC le for U-WAVE w/ t swith (160mm) igitl moel 10-160mm 573-605 ±0.03mm 10-160mm 573-615* ±0.03mm 10-210mm 573-606 ±0.03mm 10-210mm 573-616* ±0.03mm 10-310mm 573-608 ±0.04mm 10-310mm 573-618* ±0.04mm 536-105 Inh/ igitl moel.4-6.4" 573-705 ±.0015".4-8.4" 573-706 ±.0015".4-12.4" 573-708 ±.0015" *Without thum roller 10-150mm 536-105 ±0.05mm 10-200mm 536-106 ±0.05mm 10-300mm 536-107 ±0.08mm IMENSIONS 10 30 ø1 10 ø1 Vernier moel 10 30 ø1 10 igitl moel Rnge t 10-150mm 75 3 10-200mm 75 3 10-300mm 100 3.8 Rnge t 10-160mm/.4-6.4 75 3.5 10-210mm/.4-8.4 75 3.5 10-310mm/.4-12.4 100 3.8-21
ABSOUTE Bk-Jw Centerline Cliper SERIES 573 Center-to-enter & ege-to-enter Types Speilly esigne to mesure hole enterto-enter or ege-to-enter istnes. Provie with jws on the k of the slier, mesurements n e re esily from ove. iret reing of pith mesurements is ville ue to the offset vlue setting funtion. SPC t output. 573-116-10 (Center-to-enter type) 10-200mm 573-116-10 ±0.10mm 10-300mm 573-117-10 ±0.15mm IMENSIONS Center-to-enter istne type 573-118-10 (Ege-to-enter type) Ege-to-enter istne type 10-200mm 573-118-10 ±0.10mm 10-300mm 573-119-10 ±0.15mm Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error) Resolution: 0.01mm or.0005"/0.01mm isply: C Sle type*: ABSOUTE eletrostti liner enoer Mx. response spee: Unlimite Bttery: SR44 (1 p.), 938882 Bttery life: Approx. 3.5 yers uner norml use Funtions Origin-set, Zero-setting, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Optionl Aessories 959143: t hol unit 959149: SPC le with t swith (1m) 959150: SPC le with t swith (2m) 02AZ790C: SPC le for U-WAVE w/ t swith (160mm) 05FAJ735: Centerline liper inspetion gge (250) 0 50±0.015 100±0.015 150±0.015 4 ø5 (30) 30 30 (10) 64 (25) (40) ø10 ø1 573-116-10 573-117-10 ø20 ø1 573-118-10 573-119-10-22
Point Cliper SERIES 573, 536 ABSOUTE igimti n vernier type Nrrow-tip jws fit into very smll grooves n trks, mking mny previously iffiult outsie mesurements fr esier to otin. With epth r. SPC t output (Series 573). 573-621 Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error for igitl moels) Resolution*: 0.01mm or.0005"/0.01mm Grution**: 0.05mm isply*: C Sle type*: ABSOUTE eletromgneti liner enoer Mx. response spee*: Unlimite Bttery*: SR44 (1 p.), 938882 Bttery life*: Approx. 3 yers uner norml use ust/wter protetion level*: IP67 *igitl moels **Anlog moels 2011207400 536-121 Funtions of igitl Moel Origin-set, Zero-setting, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Optionl Aessories for igitl Moel 05CZA624: SPC le with t swith (1m) 05CZA625: SPC le with t swith (2m) 02AZ790A: SPC le for U-WAVE w/ t swith (160mm) igitl moel 0-150mm 573-621 ±0.02mm 0-150mm 573-625 ±0.02mm 0-150mm 573-622* ±0.02mm 0-150mm 573-626* ±0.02mm Inh/ igitl moel 0-6" 573-721 ±.001" 0-6" 573-725 ±.001" *without thum roller 0-150mm 536-121 ±0.05mm IMENSIONS 25 40 30 10 2 2 573-625, 626, 725 2 21 21 10 10 30 40 30 40 0.3 0.3 0.3 0.3 536-121 573-621, 622, 721-23
Ble Type Cliper SERIES 573, 536 ABSOUTE igimti n vernier type The thin le-type jws fit into very smll grooves n mke previously iffiult outsie mesurements fr esier to otin. The outsie mesuring fes re rietippe. With epth r. SPC t output (Series 573). 573-634 536-134 Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error for igitl moels) Resolution*: 0.01mm or.0005"/0.01mm Grution**: 0.05mm isply*: C Sle type*: ABSOUTE eletromgneti liner enoer Mx. response spee*: Unlimite Bttery*: SR44 (1 p.), 938882 Bttery life*: Approx. 3 yers uner norml use ust/wter protetion level*: IP67 *igitl moels **Anlog moels igitl moel 0-150mm 573-634 ±0.02mm 0-150mm 573-635* ±0.02mm Inh/ igitl moel 0-6" 573-734 ±.001" Funtions of igitl Moel Origin-set, Zero-setting, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Optionl Aessories for igitl Moel 05CZA624: SPC le with t swith (1m) 05CZA625: SPC le with t swith (2m) 02AZ790A: SPC le for U-WAVE w/ t swith (160mm) *without thum roller 0-150mm 536-134 ±0.05mm 0-200mm 536-135 ±0.05mm 0-300mm 536-136 ±0.08mm IMENSIONS 3.5 t 40 Virnier moel 0.75 20 igitl moel Rnge t 0-150mm 40 20 0.75 3 0-200mm 50 25 0.75 3 0-300mm 64 30 1 3.8-24
Nek Cliper SERIES 573, 536 ABSOUTE igimti n vernier type Cn mesure wll thikness insie ores n reesses. SPC t output (Series 573). 573-651 Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error for igitl moels) Resolution*: 0.01mm or.0005"/0.01mm Grution**: 0.05mm isply*: C Sle type*: ABSOUTE eletromgneti liner enoer Mx. response spee*: Unlimite Bttery*: SR44 (1 p.), 938882 Bttery life*: Approx. 3 yers uner norml use ust/wter protetion level*: IP67 *igitl moels **Anlog moels Funtions of igitl Moel Origin-set, Zero-setting, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Optionl Aessories for igitl Moel 05CZA624: SPC le with t swith (1m) 05CZA625: SPC le with t swith (2m) 02AZ790A: SPC le for U-WAVE w/ t swith (160mm) Rnge igitl moel Orer No. Aury 0-150mm 573-651 ±0.03mm 0-150mm 573-652* ±0.03mm 0-150mm 573-653 ±0.03mm 0-150mm 573-654* ±0.03mm *Point type 573-653, 573-654: without thum roller 0-150mm 536-151 ±0.05mm 0-150mm 536-152* ±0.05mm *Point type Point jw type 536-151 536-152 Inh/ 0-6" 573-751 ±.0015" 0-6" 573-752* ±.0015" *Point type igitl moel IMENSIONS 35 5 5 33.5 28.5 40 536-151 573-651, 653, 751 5 5 38 2 5 5 Point jw type 536-152 33.5 5 10 40 ø2.4 5 (e) ø0.5 Point jw type 573-652, 654, 752-25
ABSOUTE Insie Cliper SERIES 573, 536 Knife-ege/Insie Groove/Point Jw Type Speilly esigne for insie mesurements in hr-to-reh ples. SPC t output (Series 573). Knife-ege type 573-642 536-142 Insie groove type 573-745 Point jw type 536-145 Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error for igitl moels) Resolution*: 0.01mm or.0005"/0.01mm Grution**: 0.05mm isply*: C Sle type*: ABSOUTE eletromgneti liner enoer Mx. response spee*: Unlimite Bttery*: SR44 (1 p.), 938882 Bttery life*: Approx. 3 yers uner norml use ust/wter protetion level*: IP67 *igitl moels **Anlog moels Funtions of igitl Moel Origin-set, Zero-setting, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error 573-646 536-146 Optionl Aessories for igitl Moel 05CZA624: SPC le with t swith (1m) 05CZA625: SPC le with t swith (2m) 02AZ790A: SPC le for U-WAVE w/ t swith (160mm) Remrks 10-200mm 573-642 ±0.05mm Knife-ege type, Mesurle min. hole imeter: ø10mm 10-200mm 573-643* ±0.05mm Knife-ege type, Mesurle min. hole imeter: ø10mm 10-160mm 573-645 ±0.05mm Insie groove type, Mesurle min. hole imeter: ø10mm 10-160mm 573-647* ±0.05mm Insie groove type, Mesurle min. hole imeter: ø10mm 20-170mm 573-646 ±0.03mm Point jw type, Mesurle min. hole imeter: ø20mm 20-170mm 573-648* ±0.03mm Point jw type, Mesurle min. hole imeter: ø20mm *without thum roller igitl moel Knife-ege type Insie groove type Inh/ igitl moel Remrks.4" - 8" 573-742 ±.002" Knife-ege type, Mesurle min. hole imeter: ø.4".4" - 6" 573-745 ±.002" Insie groove type, Mesurle min. hole imeter: ø.4".8" - 6" 573-746 ±.0015" Point jw type, Mesurle min. hole imeter: ø.8" Remrks 10-200mm 536-142 ±0.12mm Knife-ege type, Mesurle min. hole imeter: ø10mm 10-150mm 536-145 ±0.05mm Insie groove type, Mesurle min. hole imeter: ø10mm 20-150mm 536-146 ±0.05mm Point jw type, Mesurle min. hole imeter: ø20mm 30-300mm 536-147 ±0.08mm Point jw type, Mesurle min. hole imeter: ø30mm 70-450mm 536-148 ±0.10mm Point jw type, Mesurle min. hole imeter: ø70mm 70-600mm 536-149 ±0.12mm Point jw type, Mesurle min. hole imeter: ø70mm Point jw type More thn ø20-26
IMENSIONS Knife-ege type: 536-142 288 Knife-ege type: 573-642, 643, 742 290 70 8 0.3 3 229 16 35 20 3 3 5 3 16 g X X 8 0.3 3 65 Setion X X Setion X X 233 35 20 3 23.5 5 3.5 70 57.5 74.5 90.5 16 X X 16 Insie groove type: 536-145 Insie groove type: 573-645, 647, 745 3 R5 R5 R5 R5 Point jw type: 536-146, 147, 148, 149 Point jw type: 573-646, 648, 746 (233) f e 60 ø2.4 (ø5)* (16) ø0.5 (ø1)* 56 31.5 5 (e) 28.5 2 38 5 40 (60 ) ø0.5 ø2.4 *450 n 600mm rnge moels 10 Rnge e f g 150mm 229 16 38 31 5 5 2 300mm 403 20 98 89 5 10 2 450mm 610 25 145 136 10 25 5 600mm 750 25 145 136 10 25 5-27
Tue Thikness Cliper SERIES 573, 536 ABSOUTE igimti n vernier type The em-mounte jw is roun r tht filittes mesurements of tue wll thikness. SPC t output (Series 573). 573-661 536-161 Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error for igitl moels) Resolution*: 0.01mm or.0005"/0.01mm Grution**: 0.05mm isply*: C Sle type*: ABSOUTE eletromgneti liner enoer Mx. response spee*: Unlimite Bttery*: SR44 (1 p.), 938882 Bttery life*: Approx. 3 yers uner norml use ust/wter protetion level*: IP67 *igitl moels **Anlog moels Rnge igitl moel Orer No. Aury 0-150mm 573-661 ±0.05mm 0-150mm 573-662* ±0.05mm Inh/ igitl moel 0-6" 573-761 ±.002" Funtions of igitl Moel Origin-set, Zero-setting, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Optionl Aessories for igitl Moel 05CZA624: SPC le with t swith (1m) 05CZA625: SPC le with t swith (2m) 02AZ790A: SPC le for U-WAVE w/ t swith (160mm) *without thum roller 0-150mm 536-161 ±0.05mm IMENSIONS 229 56 56 32 40 16 More thn ø3 Vernier moel ø3 235 16 32 40 igitl moel ø3-28
Hook Type Vernier Cliper SERIES 536 Cn mesure with of grooves n lns insie ores n reesses. Tehnil t Aury: ±0.03mm Grution: 0.02mm 536-171 Rnge* Orer No. Aury Remrks 0 (10) - 200mm 536-171 ±0.03mm 0 (2) - 200mm 536-172 ±0.03mm with fine justment *( ): Minimum imension in insie mesurement IMENSIONS 536-172 More thn ø30mm More thn ø30mm e f R5: 536-171 Flt: 536-172 g Rnge e f g 536-171 320 28 12 4 5 3.5 536-172 320 28 28.5 20 12 4 1 3.5 Swivel Vernier Cliper SERIES 536 Moving Jw type Tehnil t Aury: ±0.05mm Grution: 0.05mm The moving jw n e rotte to mesure setione shfts. With epth r. 536-212 0-200mm 536-212 ±0.05mm IMENSIONS 288 50 42 91 16 14.5-29
ABSOUTE ow Fore Cliper SERIES 573 ue to the low mesuring fore these lipers re iel for mesuring elsti workpiees suh s plsti prts n 0-180mm 573-191-20 ±0.05mm IMENSIONS 314 ruer prts tht stnr lipers nnot mesure urtely. SPC t output. 573-191-20 Inh/ 0-7" 573-291-20 ±.002" Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error) Resolution: 0.01mm or.0005"/0.01mm isply: C Sle type*: ABSOUTE eletrostti liner enoer Mesuring fore: 0.49N to 0.98N (50gf to 100gf) Jw retrtion: 0.3mm Mx. response spee: Unlimite Bttery: SR44 (1 p.), 938882 Bttery life: Approx. 3.5 yers uner norml use Funtions Origin-set, Zero-setting, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Optionl Aessories 959143: t hol unit 959149: SPC le with t swith (1m) 959150: SPC le with t swith (2m) 02AZ790C: SPC le for U-WAVE w/ t swith (160mm) 16 40 ABSOUTE Snp Cliper SERIES 573 The ABSOUTE igimti snp liper fetures spring-loe mehnism to llow quik n effiient GO/NO-GO inspetion for mss proution prts. SPC t output. A onsistently low mesuring fore n e gurntee y only tking mesurements when the pointer is etween the two fiuil lines. Mesurement proeure Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error) Resolution: 0.01mm or.0005"/0.01mm Repetility: 0.01mm isply: C Sle type*: ABSOUTE eletrostti liner enoer Mesuring fore: 7N to 14N (700gf to 1400gf) Jw retrtion: 2mm Mx. response spee: Unlimite Bttery: SR44 (1 p.), 938882 Bttery life: Approx. 3.5 yers uner norml use 0-100mm 573-181-20 ±0.02mm 0-150mm 573-182-20 ±0.02mm IMENSIONS 573-181-20 Inh/ 0-4" 573-281-20 ±.001" 0-6" 573-282-20 ±.001" Funtions Origin-set, Zero-setting, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Optionl Aessories 959143: t hol unit 959149: SPC le with t swith (1m) 959150: SPC le with t swith (2m) 02AZ790C: SPC le for U-WAVE w/ t swith (160mm 27.5 Rnge 0-100mm/0-4" 233 40 21 16.5 16 0-150mm/0-6" 290 50 24.5 20 16-30
Sriing Cliper SERIES 573, 536 ABSOUTE igimti n vernier type The rie-tippe jws filitte fine sriing on workpiee. With epth r. SPC t output (Series 573). 573-676 Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error for igitl moels) Resolution*: 0.01mm or.0005"/0.01mm Grution**: 0.05mm isply*: C Sle type*: ABSOUTE eletromgneti liner enoer Mx. response spee*: Unlimite Bttery*: SR44 (1 p.), 938882 Bttery life*: Approx. 3 yers uner norml use (1 yer: over 300mm moel) ust/wter protetion level*: IP67 *igitl moels **Anlog moels Funtions Origin-set, Zero-setting, Automti power on/off, t output, inh/mm onversion (inh/mm moels) Alrm: ow voltge, Counting vlue omposition error Optionl Aessories 05CZA624: SPC le with t swith (1m) 05CZA625: SPC le with t swith (2m) 02AZ790A: SPC le for U-WAVE w/ t swith (160mm) 0-150mm 573-676 ±0.02mm 0-200mm 573-677 ±0.02mm 0-300mm 573-679 ±0.03mm 0-150mm 536-221 ±0.05mm 0-200mm 536-222 ±0.05mm 0-300mm 536-223 ±0.08mm IMENSIONS igitl moel e Rnge e 0-150mm 229 46 21.5 17 16 33 0-200mm 288 50 25 20.5 16 43 0-300mm 403 64 27.5 22 20 54-31
Plsti Cliper SERIES 700 igitl Cliper for IY Plsti onstrution for lightweight use. Iel for use in lortory, woo-shop, nursery, otor s surgery, offie, et. Tehnil t Aury: Refer to the list of speifitions. (exluing quntizing error) Resolution: 0.1mm or.001"/0.1mm isply: C Sle type: Eletrostti liner enoer Mx. response spee: 1800mm/s Bttery: SR44 (1 p.), 938882 Bttery life: Approx. 2 yers uner norml use 700-127 Funtions Zero-setting, Power on/off Alrm: ow voltge, Counting vlue omposition error 700-128 0-150mm 700-127 ±0.2mm 0-150mm 700-128* ±0.5mm *eep throt type without insie mesuring jws. Inh/ 0-6" 700-126 ±.008" IMENSIONS 1 235 40 19 15 15 (60) (14.2) (34) 16 4 (60) 235 80 65 (34) (14.2) 4 16 700-127, 700-126 700-128 8-32