Instructin Manual IC ACCESS CONTROL Mde: DH16A-12CT Metal surface and keypads Un-netwrked Mde: DH16A-12CTQ Metal surface and keypads Netwrked Mde: DH16A-50CT/CTN Metal surface and keypads Un-netwrked Mde: DH16A-50CTQ/CTQN Metal surface and keypads Netwrked Mde: DH16A-60CT/CTN Plastic surface and keypads Un-netwrked Mde: DH16A-60CTQ/CTQN Plastic surface and keypads Netwrked 2014-V02 Security Technlgy Vgue Innvatin
Keypad Keypad DH16A-12CT DH16A-12CTQ Screw Wrking cnditins: temperature: -20 C ~ +50 C RH: 95% Current and vltage requirements: AC input: ~ 12V - 24V standby current: 80mA wrking current: 110mA Applicable card mde: EM IC card Effective distance: 5cm Capacity: ZONE 1: up t 1000 passwrds & crrelative card ZONE 2: up t 10 passwrds OR crrelative card DH16A-50CT/CTN DH16A-50CTQ/CTQN Wrking cnditins: temperature: -20 C ~ +50 C RH: 95% Current and vltage requirements: AC input: ~ 12V - 24V standby current: 80mA wrking current: 110mA Applicable card mde: EM IC card Effective distance: 5cm Capacity: ZONE 1: up t 1000 passwrds & crrelative card ZONE 2: up t 10 passwrds OR crrelative card 1. Can read MIFARE card. 2. Frequency: 13.56MHz. 3. Effective distance: 5cm. 4. ZONE 1: up t 1000 passwrds & crrelative card ZONE 2: up t 10 passwrds OR crrelative card 5. Card access, cde access and cmbined access. 6. Digital keypad peratin. 7. Built-in pickprf functin. 8. Watchdg timer, pwerful rebt and self-recvery watchdg can cnnect with the external unlck buttn. 9. Dual relay utputs. 10. Unlck utput delay time: 0~99s. 11. IP rating: 65. 12. Dimensin: 152*44*23.5mm. 13. Dual relay utputs fr dr pening, dr status detecting, pen dr by buttn. The functin f dr status detecting is fr ZONE 1 nly. -2- -1-1. Can read MIFARE card. 2. Frequency: 13.56MHz. 3. Effective distance: 5cm. 4. ZONE 1: up t 1000 passwrds & crrelative card ZONE 2: up t 10 passwrds OR crrelative card 5. Card access, cde access and cmbined access. 6. Digital keypad peratin. 7. Built-in pickprf functin. 8. Watchdg timer, pwerful rebt and self-recvery watchdg can cnnect with the external unlck buttn. 9. Dual relay utputs. 10. Unlck utput delay time: 0~99s. 11. IP rating: 65. 12. Dimensin: 123*79*21mm. 13. Dual relay utputs fr dr pening, dr status detecting, pen dr by buttn. The functin f dr status detecting is fr ZONE 1 nly.
Indicatr Keypad Applicable mde: DH16A-12CT/DH16A-12CTQ DH16A-60CT/CTN DH16A-60CTQ/CTQN Wrking cnditins: temperature: -20 C ~ +50 C RH: 95% Current and vltage requirements: AC input: ~ 12V - 24V standby current: 80mA wrking current: 110mA Applicable card mde: EM IC card Effective distance: 5cm Capacity: ZONE 1: up t 1000 passwrds & crrelative card ZONE 2: up t 10 passwrds OR crrelative card Befre installatin, psitin the lcatin where the cntrller unit is munted. Please perate it accrding t the fllwing steps: 1. Open the cntrller by lsening and remving the back case screw at the bttm with the spline tl. 2. Use the prvided drilling template t accurately lcate and drill the required hles. The fur drilling hles are marked "B". 3. Use the screws prvided t munt the back case n the wall. Be sure t draw the wiring thrugh the large centre hle in back case, and keep level. 4. Cnnected accurately the system wiring fllwing the label enclsed n the rear. 5. Put the unit back and screw it n by using the spline tl. 1. Can read MIFARE card. 2. Frequency: 13.56MHz. 3. Effective distance: 5cm. 4. ZONE 1: up t 1000 passwrds & crrelative card ZONE 2: up t 10 passwrds OR crrelative card 5. Card access, cde access and cmbined access. 6. Digital keypad peratin. 7. Built-in pickprf functin. 8. Watchdg timer, pwerful rebt and self-recvery watchdg can cnnect with the external unlck buttn. 9. Dual relay utputs. 10. Unlck utput delay time: 0~99s. 11. IP rating: 65. 12. Dimensin: 120*76*22mm. 13. Dual relay utputs fr dr pening, dr status detecting, pen dr by buttn. The functin f dr status detecting is fr ZONE 1 nly. -4- -3-
Wiring Diagram (Un-netwrked) Applicable mde: DH16A-50/60CT/CTN DH16A-50/60CTQ/CTQN Befre installatin, psitin the lcatin where the cntrller unit is munted. Please perate it accrding t the fllwing steps: 1. Open the cntrller by lsening and remving the back case screw at the bttm with the spline tl. 2. Use the prvided drilling template t accurately lcate and drill the required hles. The fur drilling hles are marked "B". 3. Use the screws prvided t munt the back case n the wall. Be sure t draw the wiring thrugh the large centre hle in back case, and keep level. 4. Cnnected accurately the system wiring fllwing the label enclsed n the rear. 5. Put the unit back and screw it n by using the spline tl. Red-pwer Black-pwer AC input:~ 12V - 24V Brwn-dr status detecting Orange-unlcking buttn 1 Yellw-unlcking buttn 2 Green-GND Blue-NO 2 Purple-COM 2 Gray-NC 2 White-NO 1 Pink-COM 1 Aqua-NC 1 Shielded grund AC input:~ 12V - 24V Dr bell Pay attentin t the crrect directin Shielded grund Dr lck -6- -5- Applicable fr: DH16A-12/50/60CT/CTN
Wiring Diagram (Netwrked) Press the buttn and, the mde indicatr will flash yellw, fllw the buttn twice, the mde indicatr stps flashing, Bi sund will be heard. It indicates that nly the card access is available. Press the buttn and, the mde indicatr will flash yellw, fllw the buttn and, the mde indicatr stps flashing, Bi sund will be heard, it indicates that bth the card and cde access are available. Press the buttn and, the mde indicatr will flash yellw, fllw the buttn and, the mde indicatr stps flashing and Bi sund will be heard, it indicates that card and cde access cmbined is available. -8- -7- Red-pwer Black-pwer AC input:~ 12V - 24V Brwn-dr status detecting Orange-unlcking buttn 1 Yellw-unlcking buttn 2 Green-GND Blue-NO 2 Purple-COM 2 Gray-NC 2 White-NO 1 Pink-COM 1 Aqua-NC 1 Black+white-485- Brwn+white-485+ Shielded grund Shielded grund Dr bell Pay attentin t the crrect directin Black+White 485- Brwn+White 485+ AC input:~ 12V - 24V Dr lck Applicable fr: DH16A-12/50/60CTQ/CTQN 1. ZONE 1 and 2 relays can be prgrammed fr pening the lck, up t 1000 user cards and crrelative cdes can be stred int ZONE 1, 10 user cards r cdes can be stred int ZONE 2. In additin, ZONE 1 can be prgrammed fr 3 mdes t pen the lck: card access(use card nly), card and cde access (use either card r cde), and cmbined access(use card and cde tgether).. 2. Default cde is 1234. 3. Input the admin default cde twice (1234+1234). But a. If the admin default cde yu set is tw digits, please input 12 12 b. If the admin default cde yu set is three digits, please input 123 123 c. If the admin default cde yu set is five digits, please input 12345 12345 The rest may be deduced by analgy... The admin cdes is max 6 digits. After yu enter in the setting mde, the yellw LED will be n. NOTICE In mdes: DH16A-60CT DH16A-60CTQ DH16A-60CTN DH16A-60CTQN, the buttn replaces. Access mde setting
Enter ne set number(3 digits) frm 000 t 999 data strage units, yellw LED indicatr will be flashing: 1. If red LED indicatr is n, means there is data stred in this set f unit, Add the user card and cde(zone 1) press the buttn twice t clean up; 2. If green LED indicatr is n, means this number data strage unit is vacant and can be added card and passwrds in. Add card and passwrds steps: 1. Enter in setting mde, and the yellw LED indicatr will be flashing. 2. Input three-figure frm 000 t 999 data strage units, and the green LED indicatr is n. 3. Swipe card, and a sund "BI" means added in. Then input the crrelative passwrds fr the card just added. The length f passwrds shuld be the same as admin cde. Fr example, the admin cde is 12 ( tw is the length), herein shuld set tw digits passwrds, yu can set 00-99 as yur passwrds. If the admin cde is 123 (three is the l ength), herein shuld set three d igits p asswrds, yu can set 000-999 as yur passwrds. The rest may be deduced by analgy The sund " BI " means card added in and passwrds setting Press the buttn Set the digit length f passwrd Press the buttn and yellw LED indicatr will be flashing, then press the buttn 4 and a sund "BI" as reminder, then input X(X=2,3,4, 5,6): 2--Stands fr the passwrd/cde digit length is 2(00-99) 3--Stands fr the passwrd/cde digit length is 3(000-999) The rest may be deduced by analgy, and the maximum is 6 digits. A sund "BI" as reminder, means digit length setting If the sund is "BI BI BI", means digit length is as same as the existence, and new setting is nt permitted. NOTICE Once the digit length changed, all added cards and passwrds will be cleared. t quit the setting mde. Delete the user card and cde(zone 1) Enter ne set number(3 digits) frm 000 t 999 data strage units, if red LED indicatr is n, means there is data stred in this set f unit, press the buttn twice t delete the card and cde. Add the user card r cde(zone 2) Press the buttn and, the yellw LED indicatr will be flashing. Input tw-figure frm 00 t 09 data strage units, yellw LED indicatr will be flashing; 1. But if red LED indicatr light is n, it means there is data stred in this set f unit, press the buttn twice t clean up; 2. If green LED indicatr light is n, it means this data strage unit is vacant and can be added card r passwrd in. Add card r passwrd: Swipe card, and a sund "BI" means added in; OR input t he c rrelative passwrds. The length f passwrds shuld be as same as admin cde. Fr example, the admin cde is 12 ( tw is the length ), herein shuld setting tw digits passwrds, yu can set 00-99 as yur passwrd. The admin cde is 123(three is the length), herein shuld setting three digits passwrds, yu can set 000-999 as yur passwrds. The rest may be deduced by analgy...sund "BI" heard and yellw indicatr light stps flashing, means card added in r passwrds setting Delete the user card r cde(zone 2) Press the buttn and, the yellw LED indicatr will be flashing, Input tw-figure frm 00 t 09 data strage units. If red LED indicatr light is n, it means there is data stred in this set f unit, press the buttn twice t delete the card r cde. -9- -10-
Press the buttn and, the mde indicatr will flash yellw, Enter the number frm 00 t 99, yellw light stps flashing, in the mean time a lng beep will be heard, it indicates a success f unlck time setting. 00-99 means the unlcking time, eg. 05 means the unlcking time is 5s. If set time as 00 means: swipe card r input passwrd nce t pen the dr, swipe card r input passwrd again t clse the dr. If set time as 00 means: swipe card r input passwrd nce t pen the dr, swipe card r input passwrd again t clse the dr. the buttn twice, (a cntinuus beep will be heard and mde indicatr stps flashing), it indicates all user cards and cdes have been cleaned ut the buttn twice, (a cntinuus beep will be heard and mde indicatr will turn yellw), it indicates it restres t factry defaults. Press the buttn t quit the setting mde setting. If enter wrng infrmatin, it will imply as BI.BI. sunds. The device wuld turn back withut actins in 30 secnds autmatically accmpany with BI. BI. sunds. If it is nt in the setting mde and press incmplete numbers, it will turn back in 5 secnds autmatically accmpany with BI.BI. sunds. When set as pening the dr by card cmbined with passwrd, if nly card r passwrd is used, the system will exit in 5 secnds autmatically with Bi Bi sunds. Set the unlcking time fr ZONE 1 Set the unlcking time fr ZONE 2 Press the buttn and, the mde indicatr will flash yellw, Enter the number frm 00 t 99, yellw light stps flashing, in the mean time a lng beep will be heard, it indicates a success f unlck time setting. 00-99 means the unlcking time, eg. 05 means the unlcking time is 5s delayed. Clean all user cards and cdes, restres t factry defaults A. When ZONE 1 relay actived, dr indicatr will turn green. B. When ZONE 2 relay actived, dr indicatr will turn red. In case frget the admin cde, press the buttn and hld it, then pwer n. A sund "BI" as reminder, means admin cde default setting Digit length is 2--default admin cde is 12, Digit length is 3--default admin cde is 123, Digit length is 4-default admin cde is 1234, Digit length is 5--default admin cde is 12345, Digit length is 6--default admin cde is 123456(Maxmium is 6). The pickprf alarm The built-in buzzer will send a cntinuus beeping if the phtresistr sensr is directly expsed int the light. The buzzer will be ff autmatically in 60 secnds when the light is n lnger detected, r by entering the admin cde. Mdify administratr cde Press the buttn and, the yellw LED indicatr will be flashing, then input a new administratr cde twice(the length f the new admin cde must as same as the ld ne) and a sunds "BI" means mdify Turn n/ff the pickprf alarm with the and, a lng beep will be heard whilst the mde indicatr stps flashing, pickprf alarm is turned ff. with the and, a lng beep will be heard whilst the mde indicatr stps flashing, pickprf alarm is turned n. -11- -12-
Turn n/ff the dr bell with the and, a lng beep will be heard whilst the mde indicatr stps flashing the functin f dr bell is turned ff. with the and, a lng beep will be heard whilst the mde indicatr stps flashing, the functin f dr bell is turned n. NOTICE: The relay in ZONE 2 fr dr bell is available if the functin f dr bell is turned n but the functin r dr lck is inactive. Press the buttn in standby mde, the relay cntacts ne time, the dr bell ringing is triggered. Add the master card(nly fr ZONE 1) Press the buttn and, the mde indicatr will flash green, it indicates there is n master card stred; if the indicatr turns green and n flashing, it indicates there is already data existed, press the buttn twice t clean up the data, and then indicatr will flash green, swipe the master card, a lng beep will be heard, it indicates that adding Using the master card enter the setting mde Swipe the master card, the indicatr will be yellw whilst a lng "BI" heard, enter the setting mde. Swipe the master card again, the indicatr will turn green whilst three times rapid Bi sund will be heard and exit the setting mde.. The access cntrl will be lcked fr 60s if the mistaken cde cntinuusly input r swipe the invalid card fr 5 times( bth the keypad perating and the card swiping is nt available during the 60 secnds). Detect the dr status: when smene pens the dr and cmes in, the dr is clsed, the system will autmatically detect the dr status and lck the dr even thugh it is still in delay perid(fr ZONE 1 nly). -14- NOTICE The user cde must be different frm the administratin cde. The cde f ZONE 1 must be different frm that f ZONE 2. -13- Grup cards added in ZONE 1 Press the buttn and, the yellw LED indicatr will be flashing, then press the buttn and, a sund "BI" as reminder. Then input three-figure 000 t 999 data strage units as start added unit, and input 3 digits number indicates the cards quantity yu want t add in. Fr example: 1. Input 005 060--means the cards added in strage units starting frm 005, and the quantity f the whle cards added in are 60. 2. Input 060 150--means the cards added in strage units starting frm 060, and the quantity f the whle cards added in are 150. After adding cards, a sund "BI" as reminder. Swipe the first added card r input the first added card serial number(8 digits), a sund "BI" as reminder, means added in Press the buttn t quit setting mde. Mdify the user cde f ZONE 1 Press the buttn and, the yellw LED indicatr will be flashing, then press the buttn and, a sund "BI" as reminder. Then input three-figure 000 t 999 data strage units and input crrelative passwrds (The length f relative passwrds shuld as same as admin cde). Press the buttn t quit setting mde. Setting access cntrl ID(fr netwrked mdes nly) Press the buttn and, the yellw LED indicatr will be flashing, then press the buttn and, a sund "BI" as reminder. Then input 6 digits ID number, and a sund "BI" as reminder, means ID setting Press the buttn t quit setting mde.