Test Report Number: SHAH S1

Size: px

Start display at page:

Download "Test Report Number: SHAH S1"

Ashlee Blankenship
5 years ago
Views:

Applicant: JOHNSON INDUSTRIES (SHANGHAI) CO., LTD. Date: JUN 28, 2013 AI NO.4500, BAOQIAN ROAD, ZHUQIAO TOWN, JIADING DISTRICT, SHANGHAI,CHINA Attn: SHENG YUAN THIS IS TO SUERSEDE REORT NO.

************************************************************************************************************************************************************ : As requested by the applicant, for

1 Applicant: JOHNSON INDUSTRIES (SHANGHAI) CO., LTD. Date: JUN 28, 2013 AI NO.4500, BAOQIAN ROAD, ZHUQIAO TOWN, JIADING DISTRICT, SHANGHAI,CHINA Attn: SHENG YUAN THIS IS TO SUERSEDE REORT NO. SHAH DATED MAY 30, 2013 Sample Description: One(1) piece of submitted sample said to be Bench. Item Name Item No. : Breaker Olympic Flat Bench. : MG-A678-03(FW202). ************************************************************************************************************************************************************ : As requested by the applicant, for details refer to attached page(s). ************************************************************************************************************************************************************ Conclusion: Tested sample Standard Result Submitted sample EN 957-1: stationary training equipment- general safety requirement and test methods. ass EN 957-4:2006+A1:2010 stationary training equipment strength ass training benches additional specific safety requirement and test methods ***************************************************************************************************************************************************** To be continued Authorized By: For Jacob Lin General Manager age 1 Of 4

2 1. GENERAL SAFETY REQUIREMENTS FOR STATIONARY TRAINING EQUIMENT With reference to EN 957-1: 2005 Stationary training equipment General safety requirements and test methods, the submitted sample was subjected to the following test: Number of Sample Tested: One (1) iece Initial inspection: No any damage was found. Class: SC (studio use, minimum accuracy) Maximum user s weight load as claimed by the applicant: 182kg Executive Summary: 1 Scope Normative references Terms and definitions Classification. Class: SC - 5 Safety requirements Stability of free-standing equipment Test person of 182kg. The equipment did not fall over. 5.2 External construction Edges No sharp edges existed Tube ends All tube ends were closed off Squeeze, shear, rotating and reciprocating points within the No squeeze or shear accessible area points Weights No such design. NA 5.3 Equipment access and escape The user can access and escape the training equipment easily. 5.4 Adjustment and locking mechanisms Adjustment and locking could be done well. 5.5 Ropes, belts and chains General No such design. NA Wire ropes and pulleys No such design. NA Rope and belt guides No such design. NA 5.6 ull in points No pull in points. NA 5.7 Gripping positions Integral handgrips No such design. NA Applied handgrips No such design. NA Rotating handgrips No such design. NA 5.8 Electrical safety No electrical parts NA 7 Care and maintenance rovided 8 Assembly instructions rovided 9 General Instructions for use rovided 10 Marking rovided Abbreviation: =ass F=Fail NA=Not Applicable NC=Not Conducted NR = Not Requested age 2 Of 4

3 ADDITIONAL SAFETY REQUIREMENT FOR STRENGTH TRAINING BENCHES With reference to EN 957-4:2006+A1: 2010 Stationary Training Equipment Strength Training Benches Additional Specific Safety Requirement And Test Methods, the submitted sample was subjected to the following test: Number of Sample Tested: One (1) iece Initial inspection: No any damage was found. Class: SC (S: studio, C: minimum accuracy) Maximum user s weight load as claimed by the applicant: 182 kg Maximum training weight load on barbell support as claimed by the applicant: 273 kg Executive Summary: 1 Scope Normative references Terms and definitions Classification. Class: SC - 5 Safety requirements General Benches with fixed barbell supports Rotational stability of the barbell The barbell is nonoverturned when place the 20kg weight disk on the side of the bar, with mid-plane of the disk positioned 200mm from the end of the bar Rotational stability of benches with fixed barbell supports The barbell is nonoverturned when place the 20kg weight disk on the side of the bar, with mid-plane of the disk positioned 200mm from the end of the bar Longitudinal stability The bench is nonoverturned when position the bench on a 10 slope and place a barbell loaded with 600lb on the barbell support in the highest position. 5.3 Free-standing barbell supports in conjunction with benches Non-free standing barbell NA supports. 5.4 Dimensions of the barbell support a =26mm b=65mm c=310mm 5.5 Barbell support strength The support could absorb the loads of 136kg without impairment of the performance and no breakage was found after the test. 5.6 Loading (Comply with Clause 5.2 EN957-2: 2003) - EN957-2: clause 5.2- Loading Intrinsic loading Loading: 2x182=364kg Deformation is less than 1/100 after loading. Loading: 4x182=728kg No breakage is found after test Extrinsic loading Extrinsic load for Class H Class S NA Extrinsic load for Class S Loading: 11790N Deformation is less than 1/100 after loading. age 3 Of 4

Date Sample Received: Feb.19, 2013 Testing eriod: Feb.

4 Loading: 23580N No breakage is found after test. 5.7 Barbell support The weights support was easily accessible to the user. 7 Additional instructions for use rovide 8 Marking rovide Abbreviation: =ass F=Fail NA=Not Applicable NC=Not Conducted NR = Not Requested icture 1: Sample as received icture 2: Sample as received Date Sample Received: Feb.19, 2013 Testing eriod: Feb.19, 2013 to May 30, 2013 ***************************************************************************************************************************************************** End Of Report This report is made solely on the basis of your instructions and/or information and materials supplied by you. It is not intended to be a recommendation for any particular course of action. Intertek does not accept a duty of care or any other responsibility to any person other than the Client in respect of this report and only accepts liability to the Client insofar as is expressly contained in the terms and conditions governing Intertek's provision of services to you. Intertek makes no warranties or representations either express or implied with respect to this report save as provided for in those terms and conditions. We have aimed to conduct the Review on a diligent and careful basis and we do not accept any liability to you for any loss arising out of or in connection with this report, in contract, tort, by statute or otherwise, except in the event of our gross negligence or wilful misconduct. age 4 Of 4

5 To: JOHNSON INDUSTRIES (SHANGHAI) CO., LTD. Attention: SHENG YUAN Date: Jun 28, 2013 Re: Report Revision Notification Intertek Testing Services Report Number SHAH Dated May 30, lease be informed that all the content recorded in the above captioned report will be void. This captioned report is now superseded by a revised Intertek Testing Services Report Number SHAH S1. lease return the original captioned report to us immediately. Thank you for your attention. Authorized By: For Jacob Lin General Manager

Applicant: SP BERNER PLASTIC GROUP SL Date: Jun 11, 2013 CAMINO DE LA LLOMA ALDAYA (VALENCIA) SPAIN

Applicant: SP BERNER PLASTIC GROUP SL Date: Jun 11, 2013 CAMINO DE LA LLOMA 35 46960 ALDAYA (VALENCIA) SPAIN Attn: MAPI FORTE Sample Description: One (1) submitted sample said to be : Item Name : Flexible