STRUKTURA T01-A INSTALLATION INSTRUCTIONS TOP INLET AND REAR INLET FLOOR STANDING URINAL K-5889T-ER/K-5889T-ET

Size: px

Start display at page:

Download "STRUKTURA T01-A INSTALLATION INSTRUCTIONS TOP INLET AND REAR INLET FLOOR STANDING URINAL K-5889T-ER/K-5889T-ET"

Madlyn Scott
5 years ago
Views:

1 STRUKTURA INSTALLATION INSTRUCTIONS TOP INLET AND REAR INLET FLOOR STANDING URINAL K-5889T-ER/K-5889T-ET BEFORE YOU BEGIN Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. Follow the sections that pertain to your particular installation. This will help you avoid costly mistakes. In addition to proper installation, read all operating and safety instructions. All information in these instructions is based upon the latest product information available at the time of publication. Kohler China reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. These instructions contain important care, cleaning, and warranty information - please leave instructions for the consumer. Observe all local plumbing and building codes. Carefully inspect the new urinal for damage. Site preparation may require additional tools and hardware. CAUTION: Risk of personal injury or product damage. Handle with care. Vitreous china can break or chip if the product is handled carelessly. RECOMMENDED TOOLS AND MATERIALS (NOT SUPPLIED) ( ) Open end/adjustable wrenches Tape measure Basin wrench Pipe wrench Square Level Pliers Socket wrench with sockets Screw driver Seal tape Connection wire Wire cutter Insulation tape Bushing Drill Sealant / - -1-, 2014 Copyright Kohler China Ltd., 2014

2 ROUGHING-IN * Recommended dimensions for installation only, please adjust according to actual situation. Reference Value * K-5889T-ER Unit:mm * /2" Spud Wall 952 * * NPT Tap Floor 300 K-5889T-ET *380 3/4" Spud Wall 952 * * NPT Tap Floor 300 Fig.1 1 Kohler reserves the right to change marked dimensions without prior notice. -2-

3 -3-

4 B. Install urinal B. 1. Check the regulator, see Fig.3. For top inlet urinal, fix the inlet connector as shown, see Fig Back of Urinal Connector of Top Inlet Urinal Nozzle Regulator Nut Thin Gasket Back of Urinal Rubber Gasket Hose Fig Connect inlet pipe: connect with inlet connector and sensor for top inlet urinal(inlet pipe is for purchase as per the sensor type); connect with nozzle and sensor for rear inlet urinal. The inlet pipe shall be long enough(choose and purchase as desired). 3. Install flange (see Fig.5, optional for purchase). Put the urinal against wall and align the bottom with the lines drawn. 4. Insert the screw through the screw hole (see Fig.6.) Into the L-shaped fixing block. Tighten the screw. 5. Apply silicone sealant between the urinal and the wall. 2. ( 3. ( 5 ) 4. ( 6) L 5. Fig.4 4 ) ( ) Flange Screw Hole Fig.5 5 Fig

5 IMPORTANT CONSUMER INFORMATION CONSUMER RESPONSIBILITIES If you live in a hard water area, make certain that the holes in the toilet rim are kept clean to ensure proper flushing. Toilet bowl cleaners should be used at least once a week. Use a long-handled brush to clean the rim holes, and to clean as far into the trap as possible to prevent mineral deposits from forming. Most toilet bowl cleaners are not harmful to the vitreous china surface of the urinal. Please follow the bowl cleaner manufacturer's instructions carefully. Do not use abrasive cleaners or solvents. WARNING: Risk of property or product damage. Do not use cleaners inside the wash basin. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the urinal. This damage can cause leakage and property damage. Kohler Company shall not be responsible or liable for any damage to these urinal fittings caused by the use of cleaners containing chlorine (calcium hypochlorite). WARNING Never spit phlegm and throw stub or something else into the urinal. WARNING: Risk of product damage. Do not throw into the urinal what is easy to block it, such as newspaper, paper pilch. Do not bump the vitreous china with great force to prevent it from damaging and leaking. o Do not use the product in the water below 0 C. 0C o CAUTION: Please do not use hard materials (like scouring pad) to clean product surface, especially the product logo. It is recommended to use sensors of KOHLER brand. (Urinal) 1L 3L (Urinal & Sensor matching table) (Sensor) K-8881T-VC01/VC03-AF/BN, K-8988T-C01/C03-CP/SC K-8881T-UC01/UC03-AF/BN, K-8791T-C01/C03-CP/SC,K-8431T-C01/C03-CP, K-8430T-CP, K-8787T-B01/B03-CP/SC, K-8872T-C01/C03-CP Inlet pipe for top inlet(optional for purchase) ( Urinal) (Inlet Pipe) K-8881T-VC01/VC03-AF/BN K-8881T-UC01/UC03-AF/BN K-5889T-ET-0 K-8787T-B01/B03-CP/SC K-8988T-C01/C03-CP/SC K-8791T-C01/C03-CP/SC K-8431T-C01/C03-CP K-8430T-CP K-2383T-NA -5-

TECH 2 Dew Point Retrofit Kit

TECH 2 Dew Point Retrofit Kit THORESON McCOSH TECH II Instruction Manual 412765A THORESON-McCOSH INC 1885 Thunderbird St. Troy MI. 48084 Phone 1-248-362-0960 Fax 1-248-362-5270 sales@thoresonmccosh.com