Product Information PREVENTOL CMK 40

Transcription

1 Product Information PREVENTOL CMK 40 1/8

2 Uses For the preservation of concrete additives, metalworking fluids, textile auxiliaries, thickener solutions, adhesives (including protein-based formulations) and glues, knifing fillers, aqueous coatings etc. For the formulation of disinfectants. Chemical and physical data Composition: Description: alkaline preparation of p-chloro-m-cresol (Preventol CMK) clear, yellow to brown liquid Specification* Assay (GC): min. 38 % p-chloro-m-cresol *Specification values are subject to constant monitoring. Only data given in the current edition of the "Specification" are binding. Characteristic data** Density (20 C): 1,20 1,25 g/cm 3 Crystallisation point: approx. 5 C Initial boiling point: approx. 97 C Flash point: not below 100 C DIN Ignition temperature: not below 600 C DIN ph (20 C): Ionicity: approx in 100 g/l water anionic Stability range: ph 1 14 Solubility: miscible with water **Characteristic data provide further information about the product and are not subject to constant monitoring. They are therefore not binding. Storage If correctly stored and kept in the original sealed package, the shelf life is 1 year. 2/8

3 Application Preventol CMK 40 is an aqeuous alkaline preparation of p-chloro-mcresol (Preventol CMK). This active ingredient has a broad and balanced spectrum of activity covering gram-positive and gramnegative bacteria, mould fungi and yeast. It is particularly effective against putrefactive bacteria and is therefore suitable for use in products which are difficult to preserve (e.g. protein-based formulations). Table I shows the minimum inhibitory concentrations (MIC) in mg/l of the active ingredient p-chloro-m-cresol (Preventol CMK) in nutrient agar contaminated with various organisms. Preventol CMK 40 is miscible with water in any ratio. It is best mixed into the aqueous part of the product to be preserved but can also be incorporated into the ready-to-use product. Regarding the use of Preventol CMK 40, it should be noted that unlike Preventol CMK, this product is anionic. Incorporation into nonpolar products such as mineral oil based metal-working concentrates is therefore not possible with Preventol CMK 40 in most cases. Table II gives fields of application and guide additions for Preventol CMK 40. The large number of preservation problems occurring in practice mean that preliminary trials for testing compatibility and microbiological effectiveness should be carried out for every new application. 3/8

4 Table 1 MIC values for the active ingredient p-chloro-m-cresol (Preventol CMK), contained in Preventol CMK 40 Bacteria Aeromonas punctata 200 Leuconostoc mesenteroides Bacillus mycoides Proteus mirabilis Bacillus subtilis 150 Pseudomonas aeruginosa Desulfovibrio desulfuricans 35 Pseudomonas fluorescens Enterobacter aerogenes 200 Staphylococcus aureus Escherichia coli Yeasts Candida albicans 200 Saccharomyces bailii 200 Candida krusei 200 Torula rubra 50 Rhodotorula mucilaginosa 100 Torula utilis 200 Saccharomyces cerevisiae 200 Mould fungi Alternaria tenuis Chaetomium globosum Aspergillus flavus 100 Mucor racemosus Aspergillus niger 100 Penicillium brevicaule Aspergillus terreus 200 Rhizopus stolonifer Aspergillus ustus 200 Trichophyton mentagrophytes /8

5 Table II Fields of application and guide concentrations for Preventol CMK 40* Fields of application (examples) Use Guide additions* Glues and adhesives Preservation Bone glues % Casein solutions % Gelatins % Dextrin and cellulose glues % Starch glues % Albumin solutions % Hide, leather and other protein glues % Textiles Preservation Yarn humidifiers % Sizes and finishing agents % Spinning preparations % Print thickener dilutions % Metalworking fluids Preservation Metalworking fluid concentrates Ready-for-use metalworking fluid dilutions % % Paper Preservation Filler suspensions and coating compounds % Casein-based preparations % Sizing solutions and dispersions % 5/8

6 Coatings and dyestuffs Preservation Emulsion paints % Casein-based coatings % Dyestuff pastes, knifing fillers and plastic putty Filler suspensions and thickener stock solutions % % Synthetic resin dispersions % Disinfectant and cleaning agents Disinfection Disinfectant concentrates % Ready-to-use disinfectant dilutions % Various Preservation Concrete additives % Protein solutions % Gelatins for photographic applications Protein-based extinguishing agents Polishes and wax emulsions % % % Inks % Chemical toilets Disinfection % *Where not indicated otherwise, the percentage additions are calculated relative to the total formulation. Note: The addition depends on a number of factors such as the material's germ count, the formulation, production and storage conditions. The precise application concentration should therefore be determined in tests carried out under the conditions of application. 6/8

7 Registration / Approval / Recommendation 4-chlor-meta-cresol the active ingredient in Preventol CMK 40 is registrant in the following statements: Germany: German Cosmetics Regulation and EC Cosmetics Directive, Appendix IV, Part 1: 4-chlor-meta-cresol is included in the list of approved preservatives. It is listed under Recommendation XIV of the Plastics Commission of the German Federal Institute for Consumer Health and Veterinary Medicine (BgVV) as a substance for the preservation of plastics dispersions against putrefaction. The product is approved for use in selected disinfectants under 10c of the Federal German Epiemic Act (Bundesseuchengesetz). USA: In the USA, 4-chlor-meta-cresol is approved by the FDA for use as preservatives for food contact applications. Preventol CMK has been registered by the EPA under the approval number , and for use in disinfectants, glues, adhesives, leather, latex emulsions, concrete additives and metal-working fluids. Up-to-date information on the registration status of our products can be obtained from: LANXESS Deutschland GmbH Business Unit Material Protection Leverkusen / Germany Fax: ( ) Precautions When handling Preventol CMK 40, the precautions generally recommended for handling chemicals should be observed, e.g. wearing of protective clothing, safety goggles and protective gloves. Skin contact and vapour inhalation should be avoided. If the product comes into contact with the skin, the affected area should be washed immediately with plenty of soap and water; splashes in the eyes should be rinsed out immediately with plenty of water. If irritation persists, medical attention should be obtained. Contaminated clothing should be changed at once. The current safety data sheet should be observed. This contains further information on labelling, transport and storage as well as information on handling, product safety, toxicity and ecology. Use biocides safely. Always read the label and product information before use. 7/8

8 Labelling The product Preventol CMK 40 is classified as corrosive (C). Hazard description and R-phrases: R 22: Harmful if swallowed. R 34: Causes burns. 8/8 This information and our technical advice - whether verbal, in writing or by way of trials - are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Our advice does not release you from the obligation to check its validity and to test our products as to their suitability for the intended processes and uses. The application, use and processing of our products and the products manufactured by you on the basis of our technical advice are beyond our control and, therefore, entirely your own responsibility. Our products are sold in accordance with the current version of our General Conditions of Sale and Delivery. LANXESS Deutschland GmbH Business Unit Material Protection Leverkusen/Germany Edition: