LOCTITE FT220. Section 2. Composition / information on ingredients. Section 3. Hazards identification.

Transcription

1 Safety Data Sheet LOCTITE FT220 Page 1 of 5 MSDS-No. : Revision: printing date: Section 1. Identification of the substance/preparation and of the company/undertaking Product name: LOCTITE FT220 Identification of manufacturer, importer or distributor Importer: Henkel Vietnam Co., Ltd. Room th Floor, Giay Viet Plaza, Ly Chinh Thang Street, Ward 9- District 3-HCM City, Vietnam. Phone : Fax : address of person responsible for Safety Data Sheet: ap-ua-psra.sea@henkel.com Section 2. Composition / information on ingredients General chemical description: Primer Declaration of ingredients: EINECS content Classification % Xi - Irritant; R36/37/38 Section 3. Hazards identification Hazard classification: Risk phrases: Xi - Irritant R36/37/38 Irritating to e, respiratory system and skin. Section 4. First aid measures Inhalation: Skin contact: Move to fresh air, consult doctor if complaint persists. Do not pull bonded skin apart. It may be gently peeled apart using a blunt object such as a spoon, preferably after soaking in warm soapy water. Cyanoacrylates give off heat on solidification. In rare cases a large drop will generate enough heat to cause a burn. Burns should be treated normally after the adhesive has been removed from the skin. If lips are accidentally stuck together apply warm water to the lips and encourage maximum wetting and pressure from saliva inside the mouth. Peel or roll lips apart. Do not try to pull the lips apart with direct opposing action.

2 Eye contact: Ingestion: LOCTITE FT220 Page 2 of 5 If the eye is bonded closed, release eyelashes with warm water by covering with wet pad. Cyanoacrylate will bond to eye protein and will cause periods of weeping which will help to debond the adhesive. Keep eye covered until debonding is complete, usually within 1-3 days. Do not force eye open. Medical advice should be sought in case solid particles of cyanoacrylate trapped behind the eyelid cause any abrasive damage. Ensure that breathing passages are not obstructed. The product will polymerise immediately in the mouth making it almost impossible to swallow. Saliva will slowly separate the solidified product from the mouth (several hours). Section 5. Fire fighting measures Suitable extinguishing media: Special protection equipment for firefighters: Hazardous combustion products: Foam, extinguishing powder, carbon dioxide. Fine water spray Fire fighters should wear positive pressure self-contained breathing apparatus (SCBA). Oxides of carbon, oxides of nitrogen, irritating organic vapors. Section 6. Accidental release measures Personal precautions: Environmental precautions: Clean-up methods: Ensure adequate ventilation. Do not let product enter drains. Do not use cloths for mopping up. Flood with water to complete polymerization and scrape off the floor. Cured material can be disposed of as non-hazardous waste. Section 7. Handling and storage Handling: Ventilation (low level) is recommended when using large volumes Use of dispensing equipment is recommended to minimise the risk of skin or eye contact Storage: For optimum shelf life store in original containers under refrigerated conditions at 2-8 C ( F) Section 8. controls / personal protection Ingredient Type ppm mg/m 3 Remarks ETHYL CYANOACRYLATE Time Weighted Average 0,2 ACGIH (TWA): Respiratory protection: Ensure adequate ventilation. Hand protection: Chemical-resistant protective gloves (EN 374). Suitable materials for short-term contact or splashes (recommended: at least protection index 2, corresponding to > 30 minutes permeation as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness) Suitable materials for longer, direct contact (recommended: protection index 6, corresponding to > 480 minutes permeation as per EN 374): nitrile rubber (NBR; >= 0.4 mm thickness) This information is based on literature references and on information provided by glove manufacturers, or is derived by analogy with similar substances. Please note that in practice the working life of chemical-resistant protective gloves may be considerably shorter than the permeation determined in accordance with EN 374 as a result of the many influencing factors (e.g. temperature). If signs of wear and tear are noticed then the gloves should be replaced.

3 Eye protection: LOCTITE FT220 Page 3 of 5 Wear protective glasses. Hygienic measures: Wash hands before work breaks and after finishing work. Do not eat, drink or smoke while working. Section 9. Physical and chemical properties Appearance: Odor: ph: Boiling point: Flash point: Solubility: VOC content (1999/13/EC) colourless liquid irritating not applicable > 149 C (> F) 80-93,4 C ( F) Solvent: Water, Polymerises in presence of water. < 3 % Section 10. Stability and reactivity Conditions to avoid: Hazardous polymerization: Stable under normal conditions of storage and use. Rapid exothermic polymerization will occur in the presence of water, amines, alkalis and alcohols. Section 11. Toxicological information Oral toxicity: Inhalative toxicity: Skin irritation: Eye irritation: Cyanoacrylates are considered to have relatively low toxicity. Acute oral LD50 is >5000mg/kg (rat). It is almost impossible to swallow as it rapidly polymerises in the mouth. Irritating to respiratory system, Prolonged exposure to high concentrations of vapours may lead to chronic effects in sensitive individuals, In dry atmosphere with < 50% humidity, vapours may irritate the e and respiratory system Irritating to the skin., Bonds skin in seconds. Considered to be of low toxicity: acute dermal LD50 (rabbit)>2000mg/kg, Due to polymerisation at the skin surface allergic reaction is unlikely to occur Irritating to e., Liquid product will bond eyelids. In a dry atmosphere (RH<50%) vapours may cause irritation and lachrymatory effect Acute toxicity: Value type LD50 LD50 Value > mg/kg > mg/kg application oral dermal Species rat rabbit Method OECD Guideline 401 (Acute Oral Toxicity) OECD Guideline 402 (Acute Dermal Toxicity) Skin corrosion/irritation: Species Method slightly irritating 24 h rabbit OECD Guideline 404 (Acute Dermal Irritation / Corrosion)

4 LOCTITE FT220 Page 4 of 5 Serious eye damage/irritation: Species Method irritating 72 h rabbit OECD Guideline 405 (Acute Eye Irritation / Corrosion) Germ cell mutagenicity: Type of study / administration negative bacterial reverse negative mutation assay (e.g negative Ames test) mammalian cell gene mutation assay in vitro mammalian chromosome aberration test Metabolic activation / with and without with and without Species Method OECD Guideline 471 (Bacterial Reverse Mutation Assay) OECD Guideline 476 (In vitro Mammalian Cell Gene Mutation Test) OECD Guideline 473 (In vitro Mammalian Chromosome Aberration Test) Section 12. Ecological information Mobility: General ecological information: Ecotoxicity: Cured adhesives are immobile. Biological and Chemical Oxygen Demands (BOD and COD) are insignificant. Do not empty into drains / surface water / ground water. No data available. Persistence and degradability: application Degradability Method aerobic 57 % OECD Guideline 301 D (Ready Biodegradability: Closed Bottle Test) Bioaccumulative potential / Mobility in soil: LogKow Bioconcentration factor (BCF) Species Temperature Method 0, C EU Method A.8 (Partition Coefficient) Section 13. Disposal considerations Product Method of disposal: Packaging Disposal for uncleaned package: Cured adhesive: Dispose of as water insoluble non-toxic solid chemical in authorised landfill or incinerate under controlled conditions. Dispose of in accordance with local and national regulations. Contribution of this product to waste is very insignificant in comparison to article in which it is used After use, tubes, cartons and bottles containing residual product should be disposed of as chemically contaminated waste in an authorised legal land fill site or incinerated. Disposal must be made according to official regulations. Section 14. Transport information Road transport ADR:

5 LOCTITE FT220 Page 5 of 5 Railroad transport RID: Inland water transport ADN: Marine transport IMDG: Air transport IATA: Class: 9 Packaging group: III Packaging instructions (passenger) 964 Packaging instructions (cargo) 964 UN no.: 3334 Label: 9 Proper shipping name: Aviation regulated liquid, n.o.s. (Cyanoacrylate ester) Additional Information: Primary packs containing less than 500ml are unregulated by this mode of transport and may be shipped unrestricted. Section 15. Regulations - classification and identification Indication of danger: Risk phrases: Safety phrases: Xi - Irritant R36/37/38 Irritating to e, respiratory system and skin. S26 In case of contact with e, rinse immediately with plenty of water and seek medical advice. S37 Wear suitable gloves. S60 This material and its container must be disposed of as hazardous waste. Global inventory status: Regulatory list TSCA AICS NDSL KECI (KR) INV (CN) Notification Section 16. Other information Issue date: Disclaimer This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is intended to describe our products from the point of view of safety requirements and is not intended to guarantee any particular properties. This safety data sheet was prepared in accordance with Council Directive 67/548/EEC and it's subsequent amendments, and Commission Directive 1999/45/EC.