No. Error/Event Description Possible causes Possible Solution Classif. Defective RAM memory. Defective RAM memory.

Transcription

1 1 2 Defective RM memory Defective RM memory Defective RM memory Perform a software download Perform a software download Replace the igem battery Defective Power Supply Replace the Power Supply 4 Power ailure Power drops below 4.5VD. Short-circuitry on the igem auses Reset 6 lash Program Memory ailure lash Template Memory ailure 3 RM Memory ailure 5 Error Log Database ailure onfiguration Database ailure R on lash Program rea is R on lash Template rea is Read/Write/read test has failed R on Error Log Database is R on onfiguration Database is igem defective Defective RM memory Defective RM memory Replace the igem battery Replace the igem battery E E E D + lear D D + lear D 7 Unit Price Database ailure R on Unit Price Database is Defective RM memory D + lear D 8 Statistics Database ailure R on Statistics Database is Defective RM memory D + lear D 9 Event Log Database ailure R on Event Log Database is Defective RM memory D + lear D 10 Totals Database ailure R on Totals Database is Defective RM memory D + lear D 11 Totalizers Database ailure R on Totalizers Database is Defective RM memory D + lear D 12 EM Totalizers Database ailure 13 Identity Prom Data Error R on Identity Prom data is. Logged on reset / power-on Defective RM memory Not to be considered Not to be considered N/ N/ N/ N/ N/ 16 Overflow Limit Reached R on EM Totalizers Database is Limit for suppressed overflow has been reached unction programmed with an value Reprogram function according to the pump model unction 8.6N and/or 9.6N Reconfigure unctions with values 8.6N and/or 9.6N ( type) Dirty blocking the solenoid lean the solenoid piston Defective Solenoid D + lear D Page 1 of 7

2 17 Hose test volume Hose test volume out of tolerance HOSE leakage Defective NOZZLE Leakage in the hydraulic system (after the i-meter) Replace the HOSE Replace the NOZZLE ix the leakage 18 Hose test volume Hose test volume out of tolerance (on three consecutive fillings) HOSE leakage Defective NOZZLE Leakage in the hydraulic system (after the i-meter) Replace the HOSE Replace the NOZZLE ix the leakage 19 N/ N/ N/ N/ N/ 20 Display Read back Error Display not properly connected Defective Display Defective Display board heck the Display Replace the Display Replace the Display board N/ N/ N/ illing Start with Zero Unit Price illing Start with No Unit Price Downloaded illing Start after Unit Price hange illing start without Preset Entry Sale start price ST not equal MSTER 30 POS ommunication Lost 31 POS task buffers full 32 POS R error onfigured maximum number of display read back errors has been reached ( ->.17.02) ttempted start of filling with Zero (0) Unit Price ttempted start of filling with no Unit Prices downloaded from POS. ttempted start of filling before Unit Price change timeout ( -> 23.04) Nozzle Lifted without Preset Entry though required ( -> = 1) ttempted start of filling and the unit price is not equal at ST and MSTER No poll from POS for time exceeding configured maximum offline time -> Rx and/or Tx buffers in DRT task is full R of received POS message is Unit price equals to zero Unit price was not received from the POS system ttendant tried to start a delivery after a unit price modification Preset entry is required before starting the delivery (unction 24.01) Different unit prices programmed for the ST and MSTER nozzles unction and are for the POS protocol used igem Download switch (SW2) in the wrong position igem communication protocol jumper in the wrong position Incorrect communication polarity ommunication loss between the POS system and the igem POS system hardware/software igem defective (verify the RX/TX leds) igem is not capable of process all the commands sent by the POS system POS system is sending incomprehensive commands/messages to igem Program unit price (3.0N and/or 4.0N) ontact the POS system Verify the value of unction Wait for the time configured in unction before starting the delivery Verify the value of unction Preset a value before starting the delivery Verify and correct the unit prices orrect the value of unction and 20.01, according to the POS protocol Switch (SW2) MUST be on the left position Verify the jumper according to the protocol being used Verify the polarity of the communication Verify the communication connecting the POS and igem ontact the POS system ontact the POS system ontact the POS system Page 2 of 7

3 33 N/ 21 N/ 21 N/ 21 N/ N/ Verify the status of the STOP button pushed STOP button 34 STOP button pushed 35 lending out of tolerance VP Monitor 10 fillings bad 10 fillings in row with vapor recovery flow rate out of tolerance 38 VP Monitor 72h elapsed 72 hours elapsed after error code No flow on one meter at high speed/blender pump VP Monitor internal error Internal 40 VP Monitor Reset illing terminated due to STOP button press lend Error exceeds configured max Value (%) ( - >.18) Volume ratio between the assigned meters is < 0,5% VP Monitor System (Vaporix) error or not connected VP Monitor System (Vaporix) has been reset 41 Motor feedback Errors from motor Defective STOP button utton is ly programmed unction 8.6N and/or 9.6N with values ( type) Defective Preset keypad Defective Display board Value of function 18 is too low unction 8.6N and/or 9.6N with values ( type) One of the products is not available Replace the STOP button Verify unctions 7.07 and 7.08 Reconfigure unctions 8.6N and/or 9.6N Replace the Preset Keypad Replace the Display board Verify and if necessary modify the value Reconfigure unctions 8.6N and/or 9.6N Obstruction in the suction line ir Pockets Dirty blocking the solenoid lean the solenoid piston i-meter retain relieve allowing passage Replace the i-meter from one i-meter chamber retain/relieve to another Defective Solenoid One of the products is not available i-meter retain relieve allowing passage from one i-meter chamber to another Defective Solenoid unction parameter is Obstruction in the suction line Replace the i-meter retain/relieve Modify the value of unction and to 0 42 Vap not calibrated VP system not calibrated yet 43 Vap current low 44 Vap current high Valve current is low (e.g. no connected) Valve current is high(e.g. short circuit on output) 45 Vap contactor error No contactor detected 46 Vap external error Error detected via external signal input 47 Vap electric error Vap hardware error N/ N/ N/ N/ N/ Page 3 of 7

4 50 Error on WIP in use 51 Error on idle WIP Errors from WIP used in Transaction ( -> 17.00) Errors from WIP not used in Transaction ( -> 17.01) Vapor pockets Presence of air in the suction line Defective i-meter check Replace the check Pump model not correct Reconfigure pump model (37.00) Verify and clean the Dirty in the magnetic disk magnetic disks (presence of metallic particles) Defective i-meter Defective i-meter check Pump model not correct Dirty in the magnetic disk Defective I-Meter Pulser IS defective Replace the i-meter Replace the check Reconfigure pump model Verify and clean the magnetic disks (presence of metallic particles) Replace the I-Meter Verify / Replace the Pulser IS 52 No response from WIP in use No response from WIP used in Transaction - IS defective IS - IS defective Verify / Replace the - IS Verify / Replace the IS - IS Defective IS Replace the IS 53 N/ N/ N/ N/ N/ 54 ack pulses from idle WIP Pressure applied over the hose (attendant stepping over the hose) Defective i-meter heck Magnetic disk slack Defective magnetic disk Defective I-Meter Verify / orrect Service Station internal procedures Verify and replace the check Verify the magnetic disk retaining O-ring Replace the magnetic disk Replace the i-meter 55 N/ N/ N/ N/ N/ 56 orward low on idle WIP ack pulses from WIP not used in Transaction ( -> ) orward flow on WIP Not used in Transaction (indication of leakage) ( -> ) Pump model not correct Magnetic disk slack Defective Solenoid Reconfigure pump model (37) Verify the magnetic disk retaining Ring 57 N/ N/ N/ N/ N/ Page 4 of 7

5 Pulser IS defective Verify / Replace the Pulser IS - IS defective Verify / Replace the - IS 58 omm failure with WIP in use WIP used in transaction didn t respond on re-transmission. IS - IS defective Verify / Replace the IS - IS Defective IS Replace the IS board Pulser IS defective Verify / Replace the Pulser IS - IS defective Verify / Replace the - IS 59 omm failure with WIP in idle WIP didn t respond to heart beat message IS - IS defective Verify / Replace the IS - IS Defective IS Replace the IS board N/ N/ N/ N/ N/ 62 WIP serial number mismatch WIP is exchanged. and/or Pulser were replaced Modify unction to N/ N/ N/ N/ N/ 66 LPG calibration factor mismatch LPG WIPs needs to be calibrated. To calibrate 1) enter maintenance mode and set parameter 16.05=1. 2) Remove calibration magnet from meter to be calibrated 3) exit and save 4) return calibration magnet N/ N/ N/ N/ N/ 70 No low Timeout 22 Defective ompact Pump Unit heck or oot illing was started but no fuel has been dispensed for connected solenoid configurable time ( -> 17.03) Solenoid fuse open Defective Solenoid attendant did not start the delivery heck or oot solenoid fuse in the igem Page 5 of 7

6 71 onsecutive number of no flow onfigured number of maximum consecutive No low events has been reached ( -> ) Defective ompact Pump Unit heck or oot connected solenoid Solenoid fuse open Defective Solenoid attendant did not start the delivery heck or oot solenoid fuse in the igem 72 low Lost Timeout low was lost for configured maximum time ( -> 17.03) connected solenoid Solenoid fuse open Defective Solenoid attendant did not continue the delivery solenoid fuse in the igem 73 onsecutive number of lost flow onfigured number of maximum consecutive low Lost events has been reached ( -> ) connected solenoid Solenoid fuse open Defective Solenoid attendant did not continue the delivery solenoid fuse in the igem 74 Unfinished filling illing ended before preset or prepay limit was reached Vehicle tank is full / ttendant finished the delivery No product available connected solenoid Solenoid fuse open Defective Solenoid _ solenoid fuse in the igem Page 6 of 7

7 Vehicle tank is full / ttendant finished the delivery _ 75 onsecutive number of unfinished fillings onfigured number of unfinished fillings has been reached ( -> ) No product available connected solenoid Solenoid fuse open Defective Solenoid solenoid fuse in the igem 76 Hydro ilter logged 77 attery level Low 78 LPG Excess low rate onsecutive number of fillings with Hydro ilter logged (44) attery for non-volatile RM is < 2,5 V low rate > 80 lpm on LPG nozzle Replace the battery 79 N/ N/ N/ N/ N/ 80 RTOS mail buffer exhausted Mail buffer of RTOS is exhausted Internal resources exhausted Please contact Wayne not programmed not programmed 03 is not programmed and pump running in standalone mode 04 is not programmed and pump running in standalone mode No unit price for side No unit price for side Program unit price. unction 5.0N Program unit price. unction 4.0N not programmed 05 is not programmed and pump running in serial mode No address configured for side Program address for side. unction not programmed 06 is not programmed and pump running in serial mode No address configured for side Program address for side. unction not programmed not programmed 37 (pump model type) is not programmed 38 (country code) is not programmed No pump model configured No country code configured Program pump model. unction Program country code. unction N/ N/ N/ N/ N/ Notes: or errors 1 to 12 the Grounding and the Power Supply input and output MUST be checked before any another maintenance procedure is executed. lways check the model configuration chart in order to be sure that all the parameters values are Ok. (When a unction value is blinking that indicates that the value of the function is different from the default value) The occurrence of errors 81 to 86 are associated to the following situations: 1- fter a old Start is performed 2- fter a software update (download) Page 7 of 7