Companion One. Silversphere Bedside Monitoring. Wireless. Wireless Compatibility

Transcription

1 Silversphere Bedside Monitoring Silversphere bedside monitoring devices allow higher-acuity residents and their caregivers to feel safe while residents are in their beds. With both active and passive alerting options, caregivers are notified immediately when the bedside monitoring devices are activated. Devices are supervised, meaning if the resident removes the device from the call station, an alert is provided to caregivers. WCCA (shown with CCRA-8W call cord) Options are available for both wireless and hardwired systems Wireless CCRA-8W 8' Push Button for WCCA CCRA-D8W 8' Dual Push Button for WCCA CCPA-8G 8 Gray Pneumatic Pad for WCCA Not compatible with WCCA-NC call stations Wireless Compatibility HWDA Wireless Data Router HWNA Wireless Network Router WRMA Hardwired RF Receiver WAPA Wireless Access Point CCRA-8W CCRA-D8W

2 Call Cord Options continued CCPA-8G CCSA-BD10-W CCSA-BD10-W CCSA-BD10--W-KIT Replacement Pad, 10" x 30" w/ 4-pin connection Includes 10 x 30 bed sensor pad, and WCCA-NC monitor. * Features break-away cable for safety. Replace bed pressure sensors annually. Compatible only with WCCA-NC call stations CCRA-E10W Extension Cord, 10" white, 8-pin din connectors CCRA-E10W

3 Incontinence Sensor The Incontinence Sensor wireless product is a passive alarm device used when the resident is in bed or seated in a chair. It alerts caregivers of a urinary incontinence situation that requires their attention. The Incontinence Sensor product is part of the Companion One system and utilizes the same infrastructure and reporting methods as other wireless Silversphere devices. CCSA-IS-W replacement incontinence sensor pad Initiation of the urinary incontinence alarm takes place when a pad placed on a bed or chair under a fitted sheet or comparable material becomes wet. Other than the actual incontinence itself, the resident is not required to take any action to activate the pad or create an incontinence alarm. The alarm is automatically reset once the pad becomes dry. The pad can be wiped clean and has been tested with Lysol-brand disinfectants, but must be completely dry (both wiped and air) before being placed back into service. The device is supervised, meaning if the resident removes the sensor from the call station, an alert is provided to caregivers. The reset button on the WCCA-IS does not affect device operation, but can be used for Staff Check if the zone is associated with a Staff Check zone group. Installation - Workbench The Incontinence Sensor will need to be assigned to a zone within a zone group that has the following custom user events: Long name Incontinence Alarm and short name Incont Alm to be associated with the Cord Button transmitter code on the WCCA-IS. This alarm occurs during an incontinence situation. Long name Incont Device Trbl and short name Incon Trbl to be associated with the Cord Remove transmitter code on the WCCA-IS. This alarm triggers when the sensor is disconnected. Please consult the Workbench Guide for instructions on how to add custom event names. (Page S.3 52 in section 3.8: System Options, User Events.) Incontinence Sensor* CCSA-IS-W-KIT CCSA-IS-W Wireless** Includes incontinence sensor pad and WCCA-IS monitor. Replacement incontinence sensor pad, w/ 8-pin din connector * Features break-away cable for safety. **Compatible only with WCCA-IS call stations

4 Touch Pad The CCTA touch pad provides reliable and versatile actuation for residents with limited dexterity. The CCTA features a large, ultrasensitive touch plate surface that can be easily pressed by a hand, foot, elbow, chin, etc. The grey-color tent design with clip and Velcro attachment methods allow for multiple positioning possibilities to make it simple and convenient for any resident to use. Use the security clips to attach the call device to a bed, pillow case, sheet, or resident s clothing in the right angle or tent position (Diagram A and B). The Velcro strap can be used to fasten the CCTA to a bed rail as shown in Diagram C. The 10 ft. length cord attaches to WCCA call cord station, which is included with the CCTA-KIT. CCTA-KIT CCTA Includes CCTA touch pad and WCCA monitor Replacement touch pad, w/ 8-pin din connector

5 Hardwired CCMA-8W 8' Push Button for Hardwired Stations CCMA-15W 15' Push Button for Hardwired Stations CCMA-25W 25' Push Button for Hardwired Stations Hardwired Compatibility HDCA Hardwired Data Router ECSA-Cx Call Stations ECSA-ICx Call Stations CCMA-8W (shown with ECSA-CD1) CCMA-8W CCSA-BD10 CCSA-BD10-KIT Replacement Pad, 10" x 30" w/ 4-pin modular connection Includes 10 x 30 bed sensor pad, battery-powered audible monitor, and cord from monitor to call station. * Features breakaway cable for safety. Replace bed pressure sensors annually. CCMA-DA Duplexer, modular, for attaching two call cords to one call station. CCMA-DA CCSA-BD10