PCSIR Laboratories Complex, Peshawar-Pakistan.

Transcription

1 Issue : 10/08/15 Accreditation No: Awarded to Chemical, & Calibration of PCSIR Laboratories Complex, Peshawar-Pakistan. The scope of accreditation is in accordance with the standard specifications outlined in the following page(s) of this document. The accredited scope shall be visible and legible in areas such as customer service, sample-receiving section etc and shall not mislead its users. The accreditation was first time granted on by Pakistan National Accreditation Council. The laboratory complies with the requirements of ISO/IEC 17025:2005. The accreditation requires regular surveillance, and is valid until The decision of accreditation made by Pakistan National Accreditation Council implies that the organization has been found to fulfill the requirements for accreditation within the scope. The organization however, itself is responsible for the results of performed measurements/tests. PAKISTAN NATIONAL ACCREDITATION COUNCIL Sd General Page 1 of 5

2 Issue : 10/08/15. Accreditation Scope of Chemical of PCSIR Laboratories Complex, Peshawar - Pakistan Permanent laboratory premises X Materials/ Products Tested Water field (e.g. environmental testing or mechanical testing) field Chemical 1. ph Types of test/ Properties measured 2. Sodium (Na) 3. Potassium (K) 4. Total Hardness as CaCO 3 5. Calcium Hardness as CaCO 3 6. Total Alkalinity as CaCO 3 7. Chloride (Cl) 8. Total Dissolved Solids 9. Electrical Conductivity Reference to standardized method (e.g. ISO :2003)/ Internal method reference 22 nd Edition, 2012, Method No. Method No H +. B water and wastewater, APHA/AWWA/WEF 22 nd Edition, 2012,Method No Na B. 22 nd Edition, 2012,Method No K B. 22 nd Edition, 2012, Method No C water and wastewater, APHA/AWWA/WEF 22 nd Edition, 2012, Method No Ca.B 22 nd Edition, 2012, Method No B 22 nd Edition, 2012,Method No Cl 22 nd t Edition, 2012, Method No C. 22 nd Edition, 2012,Method No B. Page 2 of 5

3 Issue : 10/08/15 Materials/ Products Tested Water Juice Milk field (e.g. environmental testing or mechanical testing) field Herbal Raw Materials Physical Types of test/ Properties measured 1. Total Plate Count (TPC) 2. Total and Fecal 3. Total Plate Count (TPC) 4. Total and Fecal 5. Total Plate Count (TPC) 6. Total and Fecal i.) Moisture/water content Reference to standardized method (e.g. ISO :2003)/ Internal method reference water and wastewater, APHA/AWWA/WEF 22 nd Edition, 2012 Method No A-B water and wastewater, APHA/AWWA/WEF 22 nd Edition, 2012 Method No.9221 A-E Physical ii). Total Ash Physical iii). Ash acid insoluble Page 3 of 5

4 Issue : 10/08/15 Calibration. Measured Quantity Accreditation Scope of Calibration of PCSIR Laboratories Complex, Peshawar - Pakistan Permanent laboratory premises X Range Calibration & Measurement Capability (CMC) expressed as an uncertainty (±) Brief description of measurement and equipment used Class F2 and Lower 0.02 mg ~ g OIMLRIII-I,2004(E) Mass/Weights classes (10 mg ~ 5kg) Weighing (10 mg ~ 6 kg) 0.09 mg ~ 0.08 g OIMLR76-I,2006(E) Temperature (Liquid In Glass Thermometers) Volume: Micropipette i). 0.5 µl ~ 10 µl ii).10 µl ~ 100 µl iii). 100 µl ~ 1000µL Pipettes i). 1 ml, ii). 2 ml, iii). 5 ml, iv). 10 ml, v). 20 ml, vi). 25 ml Graduated Cylinder i). 10 ml ii). 25 ml iii). 50 ml iv). 100 ml v). 250 ml vi). 500 ml vii) ml Volumetric Flasks i) 25 ml ii) 50 ml iii) 100 ml iv. 250 ml v) 500 ml vi) 1000 ml vii) 2000 ml Burettes i) 25 ml ii) 50 ml iii) 100 ml -20 o C ~ 200 o C 0.12 o C ~ 2 o C ASTM,E77-07, 2008(E) 0.13 µl ~ 0.14 µl 0.20 µl ~ 1.67 µl 0.76 µl ~ 3.66 µl ml ml ml ml 0.13 ml 0.17 ml 0.31 ml 1.45 ml 2.90 ml 0.12 ml 0.13 ml 0.14 ml 0.17 ml BS EN ISO :2002 Analytical Balance, Sartorius Analytical Balance, Sartorius Page 4 of 5

5 Issue : 10/08/15 Beakers i) 50 ml ii) 100 ml iii) 250 ml iv) 500 ml v) 1000 ml 0.58 ml 1.16 ml 1.53 ml 2.94 ml 5.86 ml Pressure Gauge Up to psi 1 psi Direct measurement Dead Weight Tester Electrical AC Voltage DC Voltage AC Current DC Current (Measurement) 200mV ~ 1000 V 1 uv ~ 10 mv Direct measurement Inmel mv ~ 1000 V 0.1 uv ~ 1 mv Direct measurement 0.2 ma ~ 20 A 1 ua ~ 0.1 ma Direct measurement Inmel ma ~ 20 A 0.01 ua ~ 100 ua Direct measurement *capabilities are to be expressed as uncertainties (±) for a confidence probability of not less than 95%. Page 5 of 5