Material Safety Data Sheet Material Name: DELETEP3 BAFFLE COATING 2455 ID: DLM370 / IDH No

Transcription

1 * * * Section 1 - Chemical Product and Company Identification * * * Product Trade Name DELETEP3 BAFFLE COATING 2455 Manufacturer Information Henkel Surface Technologies Contact Phone: (248) Henkel Corporation Stephenson Highway Chemtrec Emergency # (800) Madison Heights, MI * * * Section 2 - Composition / Information on Ingredients * * * CAS # Component Percent Petrolatum >60 Proprietary Solvent naphtha (petroleum), medium aliphatic Component Related Regulatory Information This product may be regulated, have exposure limits or other information identified as the following: C9 through C18 Aliphatic hydrocarbons. * * * Section 3 - Hazards Identification * * * Emergency Overview: WARNING! COMBUSTIBLE! High vapor concentrations are irritating to the eyes, nose, and respiratory tract. Eye Contact: This product may cause irritation to the eyes. Skin Contact: Prolonged and/or repeated skin contact with this product may cause irritation/dermatitis. Skin Absorption: A single exposure is not likely to result in the product being absorbed through the skin in harmful amounts. Ingestion: May cause temporary irritation of the throat, stomach, and gastrointestinal tract. Small amounts of this product, if aspirated into the lungs, may cause mild to severe pulmonary injury. Inhalation: Inhalation of vapors or mists of the product may be irritating to the respiratory system. Excessive inhalation of this material causes headache, dizziness, nausea and incoordination. Medical Conditions Aggravated by Exposure: Pre-existing eye, skin and respiratory disorders. * * * Section 4 - First Aid Measures * * * Eye Contact: Immediately flush eyes with water for at least 15 minutes, while holding eyelids open. Seek medical attention at once. Skin Contact: For skin contact, flush with large amounts of water. Seek immediate medical attention. Ingestion: If the material is swallowed, get immediate medical attention or advice -- Do not induce vomiting. Inhalation: If inhaled, immediately remove the affected person to fresh air. If not breathing, give artificial respiration, preferably mouth-to-mouth. If breathing is difficult, give oxygen. Call a physician if symptoms develop or persist. Page 1 of 5 Issue Date: 10/02/06 Revision:

2 First Aid: Notes to Physician This material, if aspirated into the lungs, may cause chemical pneumonitis; treat the affected person appropriately. * * * Section 5 - Fire Fighting Measures * * * Flash Point: 102 ºF Method Used: Pensky-Martins Closed Cup Upper Flammable Not available Lower Flammable Not available Limit (UFL): Limit (LFL): Flammability Classification: Combustible Fire & Explosion Hazards: Vapors are heavier than air and may travel along the ground to some distant source of ignition and flash back. Empty containers may retain product residue including Flammable or Explosive vapors. Do not cut, drill, grind, or weld near full, partially full, or empty product containers. Decomposition Products: Irritating and toxic gases or fumes may be released during a fire. Extinguishing Media: Dry chemical, foam, carbon dioxide, water fog. Fire-Fighting Instructions: Firefighters should wear full protective clothing including self contained breathing apparatus. * * * Section 6 - Accidental Release Measures * * * Containment Procedures: Stop the flow of material, if this is without risk. Wear appropriate protective equipment and clothing during cleanup. Clean-Up Procedures: Absorb spill with inert material. Shovel material into appropriate container for disposal. Dispose of collected material according to regulation. * * * Section 7 - Handling and Storage * * * Handling Procedures: Avoid contact with eyes, skin and clothing. Do not take internally. For industrial use only. Use this product with adequate ventilation. Storage Procedures: Keep container tightly closed and in a cool, well-ventilated place away from incompatible materials. "Empty" containers retain product residue (liquid and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, static electricity, or other sources of ignition; they may explode. * * * Section 8 - Exposure Controls / Personal Protection * * * Exposure Guidelines: Follow all applicable exposure limits. If oil mists are generated, observe the OSHA exposure limit of 5 mg/m3. The supplier recommends the following exposure limit for petroleum solvent naphtha: 100 ppm. B: Component Exposure Limits ACGIH, OSHA, and NIOSH have not developed exposure limits for any of this product's components. Engineering Controls: Ventilation should effectively remove and prevent buildup of any vapor or mist generated from the handling of this product. Page 2 of 5 Issue Date: 10/02/06 Revision:

3 PERSONAL PROTECTIVE EQUIPMENT As prescribed in the OSHA Standard for Personal Protective Equipment (29 CFR ), employers must perform a Hazard Assessment of all workplaces to determine the need for, and selection of, proper protective equipment for each task performed. Eyes/Face Protective Equipment: Wear chemical goggles; face shield (if splashing is possible). Skin Protection: Use impervious gloves. Gloves should be tested to determine suitability for prolonged contact. Use of impervious apron and boots are recommended. Respiratory Protection: If ventilation is not sufficient to effectively prevent buildup of aerosols or mists, appropriate NIOSH/MSHA respiratory protection must be provided. Work Practices: Eye wash fountain and emergency showers are recommended. * * * Section 9 - Physical & Chemical Properties * * * Physical State: Liquid Appearance: Turquoise Odor: Solvent Vapor Pressure: Not applicable Vapor Density: Not applicable Boiling Point: >319 ºF Specific Gravity: at 68 ºF (20 ºC) ph: Not applicable Viscosity: 1,000-1,500 VOC: 1.4 lbs/gl EPA Method 24 Solubility Water: Negligible Evaporation Rate: Not determined Percent Volatile: 23.7% Percent Solids: 76% * * * Section 10 - Chemical Stability & Reactivity Information * * * Chemical Stability: Stable under normal conditions. Conditions to Avoid: Keep away from heat, sparks, or open flame. Incompatibility: This product may react with oxidizing agents. Decomposition Products: Hazardous combustion products may include carbon monoxide, carbon dioxide and hydrocarbon fragments. Hazardous Polymerization: Will not occur. * * * Section 11 - Toxicological Information * * * Acute Toxicity: The petroleum oil(s) contained in this product may be mild skin and eye irritants. Inhalation of large amounts of vapor may produce symptoms of CNS depression, including nausea, headache, weakness, dizziness, loss of coordination, and coma. Repeated skin contact with this product may produce dermatitis or oil acne. B: Component Analysis - LD50/LC50 Petrolatum ( ) Dermal LD50 Rabbit: 3600 mg/kg Solvent naphtha (petroleum), medium aliphatic (Proprietary) Inhalation LC50 Rat: >5.28 mg/l/4h; Oral LD50 Rat: >5000 mg/kg; Dermal LD50 Rabbit: 3000 mg/kg Page 3 of 5 Issue Date: 10/02/06 Revision:

4 Carcinogenicity: B: Component Carcinogenicity None of this product's components are listed by ACGIH, IARC, OSHA, NIOSH, or NTP. Chronic Toxicity Epidemiology: Neurotoxicity: Mutagenicity: Teratogenicity: Other Toxicological Information: None identified. * * * Section 12 - Ecological Information * * * Ecotoxicity: No data available for this product. B: Component Analysis - Ecotoxicity - Aquatic Toxicity Solvent naphtha (petroleum), medium aliphatic (Proprietary) Test & Species Conditions 96 Hr LC50 Pimephales promelas 800 mg/l [static] 96 Hr EC50 Selenastrum 450 mg/l capricornutum 48 Hr EC50 Daphnia magna >100 mg/l Environmental Fate: No data is available concerning the environmental fate, biodegradation or bioconcentration for this product. * * * Section 13 - Disposal Considerations * * * US EPA Waste Numbers & Descriptions: If discarded, this product is considered a RCRA ignitable waste, D001. B: Component Waste Numbers No EPA Waste Numbers are applicable for this product's components. Disposal Instructions: Dispose of waste material according to Local, State, Federal, and Provincial Environmental Regulations. * * * Section 14 - Transportation Information * * * US DOT Information Shipping Name: Please refer to the container label for transportation information. * * * Section 15 - Regulatory Information * * * US Federal Regulations This product is considered hazardous under 29 CFR (Hazard Communication). Page 4 of 5 Issue Date: 10/02/06 Revision:

5 B: Component Analysis None of this products components are listed under SARA Section 302 (40 CFR 355 Appendix A), SARA Section 313 (40 CFR ), or CERCLA (40 CFR 302.4). SARA 311/312: 102 ºF Acute: Yes Chronic: No Fire: Yes Pressure: No Reactive: No State Regulations No additional information available. B: Component Analysis - State None of this product's components are listed on the state lists from CA, FL, MA, MN, NJ, or PA. The following statement(s) are provided under the California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): WARNING! This product contains a chemical known to the state of California to cause cancer. Other Regulations All components are on the U.S. EPA TSCA Inventory List. B: Component Analysis - Inventory Component CAS # TSCA DSL EINECS Petrolatum Yes Yes Yes Solvent naphtha (petroleum), medium aliphatic Proprietary Yes Yes Yes C: Component Analysis - WHMIS IDL No components are listed in the WHMIS IDL. * * * Section 16 - Other Information * * * NFPA Ratings: Health: 1 Fire: 2 Reactivity: 0 Hazard Scale: 0 = Minimal 1 = Slight 2 = Moderate 3 = Serious 4 = Severe HMIS Ratings: Health: 1 Fire: 2 Reactivity: 0 Hazard Scale: 0 = Minimal 1 = Slight 2 = Moderate 3 = Serious 4 = Severe * = Chronic hazard Key/Legend EPA = Environmental Protection Agency; TSCA = Toxic Substance Control Act; ACGIH = American Conference of Governmental Industrial Hygienists; IARC = International Agency for Research on Cancer; NIOSH = National Institute for Occupational Safety and Health; NTP = National Toxicology Program; OSHA = Occupational Safety and Health Administration; NFPA = National Fire Protection Association; HMIS = Hazardous Material Identification System; CERCLA = Comprehensive Environmental Response, Compensation and Liability Act; SARA = Superfund Amendments and Reauthorization Act The information presented herein is believed to be factual as it has been derived from the works and opinions of persons believed to be qualified experts; however, nothing contained in this information is to be taken as a warranty or representation for which Henkel Surface Technologies bears legal responsibility. The user should review any recommendations in the specific context of the intended use to determine whether they are appropriate. Contact: Product Safety and Regulatory Affairs Contact Phone: (248) This is the end of MSDS # DLM370 / IDH No Page 5 of 5 Issue Date: 10/02/06 Revision: