SEARCH ALARM DOSIMETER DKS-02PN CADMIUM. Operating Manual

Transcription

1 SEARCH ALARM DOSIMETER DKS-02PN CADMIUM Operating Manual

2 2 CONTENTS 1 DESCRIPTION AND OPERATION PURPOSE OF USE TECHNICAL SPECIFICATIONS DELIVERY KIT OF THE DOSIMETER DESIGN AND PRINCIPLE OF OPERATION LABELING AND SEALING PACKING PROPER USE OF THE DOSIMETER OPERATING LIMITATIONS PREPARATION FOR OPERATION USE OF THE DOSIMETER TECHNICAL MAINTENANCE CERTIFICATE OF ACCEPTANCE PACKING CERTIFICATE WARRANTY REPAIR STORAGE SHIPPING DISPOSAL APPENDIX А TROUBLE RECORD DURING USE APPENDIX B REPAIR APPENDIX C STORAGE APPENDIX D PUTTING IN PROLONGED STORAGE AND REMOVAL FROM STORAGE APPENDIX E VERIFICATION AND INSPECTION RESULTS... 58

3 3 This Operating Manual (hereinafter called the OM) is intended to inform the user about the principles of operation and rules of application of the search alarm dosimeter DKS-02PN CADMIUM. The manual contains all information necessary for full implementation of its technical capabilities and its proper use. The Operator Manual contains the following abbreviations: DER - ambient dose equivalent rate of gamma, X-ray and neutron radiation; PC - personal computer. 1 DESCRIPTION AND OPERATION 1.1 Purpose of use DKS-02PN CADMIUM search alarm dosimeter (hereinafter - the dosimeter) is designed to search (detect and localize) for radioactive and nuclear materials by their external gamma and neutron radiation; measure ambient dose equivalent rate (DER) of gamma, X-ray and neutron radiation; determine gamma, X-ray and neutron radiation intensity. The dosimeter is used to control illicit transfer of radioactive materials and search for sources of radioactive radiation in the following areas: Customs and Border Services; Law enforcement agencies (MIA, Security Service of Ukraine, safeguard service); Metallurgy and scrap metal storage; Vehicles monitoring, seaports and airports; Environmental inspectorate; Radioactive waste storage sites.

4 4 1.2 Technical Specifications Key specifications are presented in Table 1.1. Table 1.1 Name Measurement unit Standardized value Sensitivity to gamma radiation for ( 137 Cs), not less than (cps)/(μsv/h) 200 Sensitivity to neutron radiation for: - Thermal neutrons, not less than - Fast neutrons, not less than (pulse cm 2 )/neutron 1.2 ± 0.12, 0.12 ± Measurement range of photonionizing radiation DER μsv/h Indication range of photonionizing radiation DER μsv/h Indication range of count rate of photon-ionizing radiation cps Indication range of count rate of neutron radiation cps Main relative permissible error limit during photon-ionizing radiation DER measurement with 0.95 confidence probability ( 137 Cs) % ±(15+1/H*(10)), where H*(10) is a numeric value of measured DER equivalent to μsv/h Energy range of registered photon-ionizing radiation MeV Energy dependence of the device readings during photonionizing radiation DER measurement in the energy range from 0.05 to 3.00 MeV relative to MeV energy ( 137 Cs) % ±25

5 5 Table 1.1 (continued) Name Anisotropy of the dosimeter when gamma radiation is recorded at gamma quanta incidence at angles from +60 о to - 60 о horizontally and vertically relative to the main measurement direction, marked by a + symbol: - for 137 Cs and 60 Со isotopes - for 241 Am isotope Measurement unit % Standardized value Energy range of registered neutron radiation ev Time of operating mode setting, not more than min 1 Calibration time by the level of gamma background s 2 60 Response time to over 10 times change of photon-ionizing radiation DER s 0.25 Operating supply voltage of the dosimeter from lithium-polymer battery V 3.7 Continuous operation of the dosimeter when powered by the charged battery under natural background radiation and switched hrs 40 off display backlight, not less than Operating temperature range С Dimensions of the dosimeter without a clip, not more than mm Weight of the dosimeter, not more than kg 0.28

6 1.2.2 The dosimeter features a threshold alarm system with three independent threshold levels: - Search threshold level or sigma-threshold (threshold level of pulse count rate from the detector of gamma radiation); - Safety threshold level (threshold level of gamma radiation DER); - Neutron threshold level (threshold level of pulse count rate from the detector of neutron radiation) Search threshold level is calculated automatically by the dosimeter in the mode of calibration by the gamma background intensity level and consists of the background counting rate and the programmed number of rms deviations of background counting rate. Calibration time by the level of gamma background intensity ranges from 2 to 60 seconds. The programming range of the number of rms deviations - from 1 to 9.9. Programming resolution The dosimeter signals about the search threshold level exceeding with light (red), vibration or sound signals "Sigma threshold exceeding". Any combination of alarms is possible, while at least one type must remain. The alarm is duplicated in the display of the dosimeter by highlighting of a corresponding icon Safety threshold level is programmable in the XXX.YY format in µsv/h or msv/h. The minimum safety threshold level may not be less than 0.3 µsv/h. The dosimeter signals about this threshold level exceeding with light (red), vibration or sound signals "Safety threshold exceeding". Any combination of alarms is possible, while at least one type must remain. The alarm is duplicated in the display of the dosimeter by highlighting of a corresponding icon Conditional threshold alarm level by neutron channel is set with the values from 1 to 9, where 1 is the highest sensitivity of the device to neutron radiation (but also the greatest probability of false positives), and 9 is the lowest sensitivity and lowest probability of false positives. Programming resolution 1. The dosimeter signals about this threshold level exceeding with light (blue), vibration or sound signals "Neutron threshold exceeding". Any combination of alarms is possible, while at least one type must remain. The alarm is duplicated in the display of the dosimeter by highlighting of a corresponding icon Threshold alarm of the dosimeter triggers no later than in 2 seconds after the level of gamma radiation increases above the background value (with gamma radiation DER level of 0.1 µsv/h) to the DER level of 0.5 µsv/h for a maximum time of 0.5 sec. 6

7 1.2.7 The frequency of false signaling for gamma and neutron radiation - less than 1 per 10 hours of operation in a stable background environment and the following values of threshold levels: - Search - 4; - Safety - 1 µsv/h; - Neutron The dosimeter does not give false signals about the presence of neutron radiation when exposed to gamma radiation from gamma source with 60 Со or 137 Cs with DER value of 100 µsv/h The dosimeter offers a possibility of automatic event logging in the nonvolatile memory, namely: - switching the dosimeter on; - switching the dosimeter off; - search threshold level exceeding; - safety threshold level exceeding; - conditional threshold level exceeding from the detector of neutron radiation; - saving measurement by the user s command; - settings change by the administrator; - device s flash memory erasing Nonvolatile memory capacity allows storing up to 65,000 records of registered event Data communication between the dosimeter and the PC is done via USB The dosimeter displays signs of the low battery The dosimeter remains operable under: - Ambient temperature from -20 to +50 C; - Relative humidity up to 100% at 35 C temperature without humidity condensation; - Atmospheric pressure from 84 to kpa The dosimeter is resistant to sinusoidal vibrations by N1 group according to GOST standard The dosimeter is resistant to single shocks with the following parameters: - Shock pulse duration - 6 ms - Maximum shock acceleration - 50 m/s 2. 7

8 The dosimeter is resistant to falls on each of its six edges from a height of 0.75 m on the concrete floor The dosimeter remains unaffected by constant and alternating magnetic field of (50±1) Hz frequency and 400 A/m intensity The dosimeter is immune to gamma and X-ray radiation of up to 10 Sv/h DER for 5 minutes The ingress protection rating of the dosimeter in compliance with GOST standard is IP The dosimeter is resistant to electromagnetic fields of frequency range in accordance with DSTU IEC : 2007 standard in the frequency range from 80 to 1000 MHz with intensity of 3 V/m (test level 2) The quasi-peak value of the radio-noise field intensity at a distance of 3 m from the dosimeter does not exceed the values for class B equipment according to GOST

9 1.3 Delivery kit of the dosimeter The delivery kit of the dosimeter includes the units and maintenance documentation presented in Table 1.2. Table 1.2- Delivery kit Item Type Q-ty Note Search Alarm Dosimeter DKS-02PN CADMIUM ВІСТ Charging device 1 Model is not specified Operating Manual ВІСТ HE 1 Events Reader software 1 On a mini CD Case 1 Model is not specified 9

10 Design and principle of operation General information, design description Appearance of the dosimeter is shown in Figure 1. Figure 1 Outlook of the dosimeter

11 In terms of design, the dosimeter is made in a shape derivative of rectangular parallelepiped with replacement of flat planes with surfaces with large radii of curvature with rounded edges. The body is dustproof and waterproof, plastic. Dosimeter s working position - vertical. The ingress protection rating is - IP67. The body consists of two covers (1) and (2) connected by screws. The front cover (1) contains a graphical color display (3), multifunctional manipulator (joystick) (4), indicators "GAMMA" (7) "NEUTRON" (8) "BATTERY" (9) and light sensor "ABC" (10). The light panel (5) for signaling when radioactive sources are detected is located in the upper part of the cover. A spring clip retainer (11) is secured with one screw on the back cover, with the help of which the dosimeter is securely fastened on the operator s clothes, and which can be easily removed, if necessary. The back cover and the clip are marked with "+" symbols (12), which stand for the mechanical centers of gamma and neutron radiation detectors. On the right lateral surface of the dosimeter s body under the protective flexible plug (6) there is a USB connector for connecting of the peripheral devices and charging of the built-in battery. Power supply of the dosimeter is charged by a lithium-polymer battery of 3.7 V rated voltage. The dosimeter is sealed with a paste in the recesses (13) of the bottom cover. 11

12 1.4.2 Operation of the dosimeter The dosimeter consists of the following main parts: high sensitivity detecting unit of gamma radiation (GDUh), low sensitivity detecting unit of gamma radiation (GDUl), detecting unit of neutron radiation (NDU), supply voltage formers (SVF), bias voltage formers (BVF), GPS/GNSS receiver (NAV), display and processing module (DPM), graphical color display (GCD), battery (B), thermal detector (TD). GDUh consists of the detector of CsI(Tl) scintillator type with silicon photomultiplier and amplifier, while NDU - of the detector of LiI(Eu) scintillator type with silicon photomultiplier and amplifier. GDUl is a Geiger-Muller counter. The principle of operation of the detecting unit is based on the transformation of scintillations in the semiconductor photomultiplier caused by gamma or neutron radiation in the scintillator into the voltage pulses. These pulses are fed to the input of the amplifier where they become amplified and come to the output as pulses of positive polarity. The number of these pulses is proportional to gamma or neutron radiation DER, and the amplitude to the energy. To ensure high temperature stability of the detectors with silicon photomultiplier, DPM carries out constant temperature compensation, measuring the exact values of temperature at the detectors, and precisely adjusts their bias voltage. DPM processes the pulse flow coming from the outputs of GDUh, GDUl, NDU, and calculates the value of gamma radiation DER, which corresponds to this flow considering the multichannel amplitude analysis, and the pulse count rate from GDUh, GDUl, and NDU. Depending on the operating mode of the dosimeter, the GCD displays the readings of DER, flux intensity, intensity flow histogram, statistical error by gamma and neutron channels. If DER exceeds 100 µsv/h by gamma channel, GDUh is automatically turned off, and the DER value is calculated from GDUl that runs continuously. The DPM consists of the non-volatile memory, which stores entries of the events log. 12

13 Labeling and sealing The upper cover and the panel of the dosimeter is inscribed with the name and a symbol of the dosimeter, the ingress protection rating and the manufacturer s trademark The lower cover of the dosimeter contains the factory serial number and the date of manufacture Sealing of the dosimeter is performed by the manufacturer Removal of seals and repeated sealing is performed by the company after repair and calibration of the dosimeter. 1.6 Packing The dosimeter, the charger and the operating manual are placed into a dust and waterproof case The case with the dosimeter kit is put into a cardboard packing box, which is glued up on both sides with a plastic film with a sticky layer.

14 14 2 PROPER USE OF THE DOSIMETER 2.1 Operating limitations Operating limitations are presented in Table 2.1. Table 2.1 Operating limitations Operating limitation 1 Ambient air temperature Limitation parameters from - 20 to 50 С 2 Relative humidity Up to 100 % at 35 С temperature without humidity condensation 3 Effect of gamma radiation Gamma radiation DER up to 10 Sv/h during 5 min 2.2 Preparation for operation Scope and order of external examination Before using the dosimeter, unpack it and check if the delivery kit is complete. Examine for mechanical damages Rules and order of examination for operational readiness Read this OM carefully before you start, and examine the location and purpose of indicators and controls Charge the battery by connecting the charger to the USB-port of the dosimeter. However, if the dosimeter was on, it would automatically turn off and switch to the charging mode, and the display would show the battery charging process animation:. Notes 1 The dosimeter is equipped with a lithium-polymer battery with no "memory effect", which can be charged at any time. 2 Fully charge the battery before the long-term storage of the dosimeter.

15 2.2.3 List of possible troubles and troubleshooting The list of possible troubles and troubleshooting is presented in Table 2.2. Please record the possible troubles in the table of Appendix A of the Operating Manual. Table Possible troubles and troubleshooting Trouble, its manifestation and additional features The dosimeter does not switch on No communication between the dosimeter and the PC The dosimeter s battery does not charge Probable cause The battery is discharged Damaged USB cable 1 Damaged USB cable 2 Charging device is out of order Troubleshooting Charge the battery Replace the USB cable 1 Replace the USB cable 2 Replace the charging device At failure to eliminate the troubles presented in Table 2.2, or at detection of more complicated troubles, the dosimeter should be sent for repair to the manufacturer. 15

16 Use of the dosimeter Safety measures during use of the dosimeter All works on the dosimeter use should be carried out according to the requirements set out in the following documents: "Radiation Safety Standards of Ukraine" (NRBU-97). State hygienic standards DHN , "Basic Sanitary Rules of Radiation Safety of Ukraine" (OSPU-2005) DSP The dosimeter s surface contains no voltages hazardous for life The dosimeter meets the requirements of DSTU 7237:2011 standard in terms of protection against electric shock by 0 Safety class according to GOST A special protective jacket is used to prevent accidental contact with conductive parts. Ingress protection rating is - IP67 according to GOST The dosimeter meets the requirements of GOST , GOST of fire safety Direct application of the dosimeter is not dangerous for personnel and is environmentally friendly In the event of contamination the dosimeter is subject to decontamination by wiping its surfaces by a gauze swab moistened with a standard decontaminating agent Disposal of the dosimeter should be performed in compliance with the "Laws of Ukraine" On Environmental Protection" and "On Waste", by group 4 DSanPiN , i.e. metal is recycled or melted, and plastic parts are dumped Operating modes of the dosimeter The dosimeter has the following modes: - Switching on/off ( ); - DER measurement and indication by gamma and neutron channels ( ); - Intensity histograms display by gamma and neutron channels ( ); - Setting up the dosimeter ( ); - Mode of data communication with PC ( ) A joystick with a central button (according to Figure 1) is used to manage operation of the dosimeter. Use the joystick to change the operating modes of the dosimeter, its settings, and navigate the menu. The central button serves to save the settings, confirm the entered data, recalibration and switching on/off the dosimeter.

17 A graphical color display is used to control the dosimeter s operation In the process of operation the dosimeter generates the following vibration-sound and light signals Vibration and sound signals: "Quantum" - a sequence of short beeps that indicate to the intensity of registered gamma quanta or neutrons. Signal frequency is proportional to the count rate of gamma rays or neutrons. Signal "Quantum" can be enabled or disabled only in the mode of the intensity histogram display by gamma and neutron channels. "Sigma threshold level exceeding" - periodic light, sound and/or vibration signals that indicate to the exceeding of the intensity threshold of gamma quanta count or conventional neutrons threshold level. "Safety threshold level exceeding" - periodic light, sound and/or vibration signals generated when the measured value of gamma radiation DER is higher than the safety threshold level. "Low battery" - periodic light, sound and/or vibration signals that indicate to a significant discharge of the dosimeter s battery. These signals can be completely disabled. "Turning the dosimeter on/off" - polytonic sound, vibration and light signals, which indicate that the dosimeter was switched on or off. These signals can be completely disabled. "Key tone" - sound and/or vibration signals generated when there was some manipulation with the dosimeter s controls. These signals can be completely disabled Operation procedure of the dosimeter The general algorithm of control of the dosimeter s operation is as follows. As soon as switched on, the dosimeter enters the mode of DER measurement and indication by gamma and neutron channels, and starts calibration by gamma background level and testing gamma radiation detector efficiency. The duration of calibration is from 60 to 2 s depending on the gamma background DER. An icon fully filled with green color and no flashing "background" inscription inside it indicate to the calibration completion.

18 18 Notes 1 Calibration by the level of gamma background is done automatically when the dosimeter is switched on as required by the user. Calculation of the search sigma threshold level of the alarm is performed regardless of the operating mode of the dosimeter. 2 For manual recalibration while in DER measurement mode, press and hold "OK" button of the joystick for at least 2 seconds. The icon will start filling once again, and the "background" inscription will start flashing. The dosimeter features the mode of audio alarm of registered gamma quanta or neutrons, which turns on and off only in the mode of intensity histogram display by gamma and neutron channels. To enable/disable this mode, press and hold "OK" button of the joystick for at least 2 seconds. For recalibration in terms of intensity of sounding briefly press "OK" of the joystick. Each short press of the joystick rightwards switches the dosimeter between the modes in the following sequence: - the mode of DER measurement and indication by gamma and neutron channels ( ); - the mode of intensity histograms display by gamma and neutron channels ( ); - the mode of the dosimeter setup ( ), which contains the following: Display ( ) Sound ( ) Vibration ( ) Light ( ) Language ( ) GPS ( ) Measurement ( ) Time and Date ( ) About device ( ) By pressing the joystick leftwards, the dosimeter switches between the modes in the reverse sequence. Regardless of the operating mode of the dosimeter, the following icons can be displayed in the top two lines of the display: - display of the current battery status - display of the current time - display of the GPS-receiver status

19 19 - display of the dosimeter s internal memory overflow - display of the alarm threshold level exceeding - display of the gamma background calibration process rate - display of the alarm status of gamma rays or neutrons counting - audible alarm status display - vibration alarm status display - light alarm status display When connecting the dosimeter via the USB-cable to the PC (if the dosimeter was switched on), it automatically switches off and proceeds to the charging mode. Run the "Events Reader" SW and enter the correct password to switch to the mode of data communication with the PC. After completion of operation and exit from the "Events Reader" SW, the dosimeter automatically turns off and proceeds to the charging mode until disconnected from the PC Switching the dosimeter on and entering the measurement mode Hold down the central joystick button for at least 3 seconds to switch the dosimeter on. Backlight of the graphical color display (hereinafter called the display) shows that the dosimeter is on, and then it will display information about the device and the producer s trademark (Fig. 2). If icon appears on the display when you try to turn on the dosimeter, it means that the battery is completely discharged and it should be charged ( ). Note Light, sound and/or vibration signals of the dosimeter switching-on can be enabled or disabled with the help of the relevant items of the setting mode. ( ). After switching on, the display shows the login window (Fig. 3).

20 20 Figure 2 - Switching on the dosimeter Figure 3 Login screen When you move the joystick up or down, choose one of the login options: "User" or "Administrator" and press the central joystick button. Operation in the "Administrator" mode is different in that you can modify the dosimeter settings that directly affect its operation (thresholds levels of the alarm triggering by gamma and neutron channels, as well as the time and date of the device), therefore to enter the "Administrator" mode you must enter the password provided by the manufacturer of the dosimeter (Fig. 4). Figure 4 Entering the administrator password When you move the joystick up or down, choose the required number for each section of the password and press the central button. Shifting between the sections is done by pressing the joystick leftwards or rightwards. After pressing the central joystick button, the dosimeter switches to the mode of DER measurement and indication by gamma and neutron channels ( ).

21 21 WARNING! Do not share the login password as "Administrator" with individuals who will use the dosimeter as "Users". They should not be able to change settings that directly affect the dosimeter s operation Switching off the dosimeter Hold down the central joystick button for at least 3 seconds to switch the dosimeter off. The display shows the information about the manufacturer and the dosimeter switches off The mode of DER measurement and display by gamma and neutron channels Once enabled as a "User" or as an "Administrator" the dosimeter enters the mode of DER measurement and indication by gamma and neutron channels. "DER" inscription in the upper left corner of the display speaks for the dosimeter s operation in this mode. Figure 5 Mode of DER measurement and indication The window is divided into two independent display areas: the upper one displays DER and the pulse count rate of gamma radiation, while the lower one DER and the pulse count rate of neutrons. The resolution of display of the pulse count rate of gamma radiation is 1 cps, that of neutrons cps. A unit of measurement is specified near each value, according to which the data is displayed at this point of time. An analogue scale of pulse count intensity is also present at each display area, which automatically changes the gradation depending on the radiation intensity, and a statistical error in percentage is displayed as well (Fig. 5).

22 22 If the set threshold level of alarm triggering by sigma threshold is exceeded, icons and alternately appear in the area of icons display. If the threshold level of alarm triggering by neutrons count rate is exceeded, icons and alternately appear in the area of icons display, whereas triggering of both alarms causes alternate appearance of icons and in the area of icons display. Light, sound and/or vibration alarms also turn on according to the dosimeter s settings ( ). If the set threshold level of alarm triggering by the level of security is exceeded, icon appears, and light, sound and/or vibration alarms also turn on according to the dosimeter s settings ( ). Note - If you need to recalibrate the dosimeter by sigma-threshold for gamma radiation, you should hold down the central joystick button for at least 2 seconds in the mode of DER measurement and indication by gamma and neutron channels. IMPORTANT! If DER is over 50 µsv/h, only the alarm by the security level would trigger and it would be impossible to recalibrate the dosimeter by sigmathreshold of gamma radiation. IMPORTANT! The effect of powerful electromagnetic radiation on the device may cause false readings and false alarms.

23 The mode of intensity histograms display by gamma and neutron channels To switch to the mode of intensity histograms display by gamma and neutron channels, move the dosimeter s joystick to the left or to the right (depending on the current operating mode of the dosimeter). "FID" inscription in the left upper corner of the display indicates to operation in this mode. Figure 6 Histograms display mode The window is divided into two independent display areas: the upper one reflects DER, gamma radiation pulse count rate and an intensity histogram of gamma radiation reflecting pulses for each 100 ms during the last 28 seconds, and the bottom one - DER, neutrons pulse count rate and an intensity histogram of neutron radiation reflecting pulses for each 100 ms during the last 28 sec. The resolution of display of the pulse count rate of gamma radiation is 1 cps, that of neutrons cps. A unit of measurement is specified near each value, according to which data is displayed at this point of time. A figure in the upper left corner of the histograms indicates its current dimension, and each point in the histogram field on the vertical axis indicates the 1/10 of this value (Fig. 6). Note - In the absence of a neutron radiation source in the environment, the intensity histogram of neutron radiation would not be observed on the display since the common background radiation contains no neutron component.

24 24 If the set level of alarm triggering by sigma threshold for gamma radiation is exceeded, icons and alternately appear in the area of icons display. If the threshold level of alarm triggering by neutrons count rate is exceeded, icons and alternately appear in the area of icons display. Whereas triggering of both alarms causes alternate appearance of icons and in the area of icons display. Light, sound and/or vibration alarms also turn on according to the dosimeter s settings ( ). If the set threshold level of alarm triggering by the level of security is exceeded, icon appears, and light, sound and/or vibration alarms also turn on according to the dosimeter s settings ( ). To enable and disable audio sounding of pulse count rate, hold down the central joystick button for at least 2 seconds. icon indicates to the enabled mode of pulse count rate sounding, icon - to the disabled. Short pressing of the central joystick button in the event enabled sounding of pulse count rate initiates recalibration of the sounding rate relative to the current pulse count rate, which facilitates distinguishing of sounds when the dosimeter approaches a radiation source and switch sounding from the mode of continuous signal to distinguishable periodic one.

25 The mode of the dosimeter setup To switch to the setup mode, move the dosimeter s joystick to the left or to the right (depending on the current operating mode of the dosimeter). "SET" inscription in the left upper corner of the display indicates to operation in this mode. Figure 7 Dosimeter setup mode The dosimeter setup mode includes the following items (Fig. 7): Display backlight setup, Sound setup of sound notifications and alarms, Vibro setup of vibrating notifications and alarms, Light setup of light notifications and alarms, Language choice of data display language on the dosimeter display, GPS configuration of the dosimeter s GPS-receiver, Measurements setting thresholds of the alarm triggering and tracks saving, Time&Date setting the time and the date, Device Info Information about the device and the manufacturer. To switch to the desired item of settings, move the dosimeter s joystick up or down until this item becomes highlighted by the cursor, then press the central joystick button to confirm switching to this item.

26 26 To change the settings in items "Display", "Sound", "Vibro", "Light" and "GPS", move the dosimeter s joystick up or down until you select the desired option, then move the dosimeter s joystick leftwards or rightwards to select, or a different value depending on the selected parameter. To change the settings in the "Language" item, move the dosimeter s joystick up or down until you select the desired language, then press the central joystick button to confirm your choice. To change the settings in items "Measurements", "Time&Date" and subitem "Change Password" of the item "Device Info", move the dosimeter s joystick up or down until you select the desired option, then press the central joystick button to confirm your choice. Then, you should move the dosimeter s joystick leftwards or rightwards until you select the desired value or unit of measurement, and then move the joystick up or down until you select the desired value. Press the central button of the joystick to return to selection of other parameters of the respective item. Each item of the setup menu contains icons (in addition to "About Device") and responsible for saving the settings and returning to the previous menu without saving settings respectively. To select the desired icon, move the dosimeter s joystick up or down until this icon becomes highlighted with green cursor (for example, ), then press the central joystick button to confirm.

27 Display Display item contains the following settings (Fig. 8): Figure 8 Display parameters setup Brightness makes it possible to set the display backlight intensity ranging from 10% to 100% in 10% increment, or "Auto". When selecting the display backlight intensity "Auto", its intensity is adjusted automatically, depending on the external lighting. Backlight Interval - makes it possible to set the following display backlight time: 15 s, 30 s, 60 s, 120 s, 300 s or continuous backlight.

28 Sound Sound item contains the following settings (Fig. 9): Figure 9 Setup of sound signals Sound ON makes it possible to enable or disable the beeps when switching the dosimeter on and off; Sound Keys makes it possible to enable or disable sounding of manipulation with the dosimeter controls; Sound Signal makes it possible to enable or disable the audible alarm triggered by exceeding the threshold level of radiation; Sound Bat. makes it possible to enable or disable the audible alarm when the dosimeter s battery is discharged.

29 Vibration Vibration item contains the following settings (Fig. 10): Figure 10 Setup of vibration signals Vibr. ON makes it possible to enable or disable vibration signals when switching the dosimeter on and off; Vibr. Keys makes it possible to enable or disable vibration during manipulation with the dosimeter controls; Vibr. Signal makes it possible to enable or disable the vibration alarm triggered by exceeding the threshold level of radiation; Vibr. Bat. makes it possible to enable or disable the vibration alarm when the dosimeter s battery is discharged.

30 Light Light item contains the following settings (Fig. 11): Figure 11 Setup of light signals Light ON makes it possible to enable or disable light signals when switching the dosimeter on and off; Light Signal makes it possible to enable or disable the light alarm triggered by exceeding the threshold level of radiation; Light Bat. makes it possible to enable or disable the light alarm when the dosimeter s battery is discharged.

31 Language Language item makes it possible to change the data display language on the dosimeter display (Fig. 12): Figure 12 Language setup GPS GPS item contains the following settings (Fig. 13): Figure 13 GPS-receiver parameters setup GPS power supply - makes it possible to enable or disable the dosimeter s GPS-receiver; GPS data update - makes it possible to set the following coordinates update interval: 15 s, 30 s, 60 s, 120 s, 300 s or continuous update;

32 32 GPS information - makes it possible to switch to viewing the current data of GPS-receiver, namely, time, date, coordinates, number of satellites currently found by the device (SIU), as well as information on whether these coordinates are reliable (Fig. 14). Figure 14 GPS information Measurement Measurement item contains the following settings (Fig. 15): Figure 15 Measurement parameters setup Sigma threshold Gamma - makes it possible to set the threshold of the alarm triggering by the number of exceedances of the mean square value of pulse count rate of gamma radiation; Conditional threshold Neutrons - makes it possible to set the conditional threshold of the alarm triggering by neutrons; Safety Threshold - makes it possible to set the threshold of the alarm triggering by the DER value;

33 33 Save measurements - allows saving the events with current coordinates, time and DER in the dosimeter s memory during measurement. If GPS-receiver was disabled at the time of saving, or there was no communication with satellites, information about current coordinates will not be added to the event. IMPORTANT! The options to configure "Sigma threshold Gamma", "Conditional threshold Neutrons" and "Security Threshold" are available only after logging in the "Administrator" mode ( ). The dosimeter s memory allows storing about 65,000 events. If and icons alternatively appear in the top line of the display, it means that the dosimeter s memory is full and a further saving of events is impossible. To read the events and clear them from the dosimeter s memory use the "Events Reader" software ( ) Time and Date Time and Date item contains the following settings (Fig. 16): Figure 16 Time and date parameters setup Current time - makes it possible to set the current time; Current date - makes it possible to set the current date. IMPORTANT! The option to configure "Current time" and "Current date" parameters is available only after entering the "Administrator" mode ( ).

34 About the device Item "About the device" contains information about the model of the dosimeter, version of its trademark software, serial number, and information about the dosimeter s manufacturer (Fig. 17). Figure 17 About the device This item also contains the subitem "Change password" that allows you to change the password in the "Administrator" mode ( ). The subitem "Change Password" contains the following items (Fig. 18): Figure 18 Password change Enter password - enter the current password in this field; Enter new password - enter a new password in this field; Repeat new password - reenter the new password in this field.

35 Data communication with PC Installation of software To read and review the events from the dosimeter and setting its parameters use the "Events Reader" software (hereinafter "Events Reader" SW), which is supplied by the dosimeter s manufacturer. IMPORTANT! You need to know the password to log in as "Administrator" to use the "Events Reader" SW. It is common for operation with the dosimeter and this SW. To realize the option of data communication of the dosimeter and the personal computer (hereinafter PC) you first need to install the driver supplied by the dosimeter s manufacturer. After installing the driver, you have to install the "Events Reader" SW. Installation of drivers and "Events Reader" SW is similar to installing other applications and does not require any special skills. IMPORTANT! Smooth operation of "Events Reader" SW requires installation on the PC of the OS Windows 7 and higher. To install the driver and "Events Reader" SW you might need to login in the OS of your PC as the "Administrator". In case of complications, please contact your system administrator who supports your PC Setting data communication with PC Connect the dosimeter via USB-cable to the PC. If the dosimeter is switched on, it automatically switches off and proceeds to charging mode. To switch to the mode of data communication with PC you have to run "Events Reader" SW (through a link on the desktop or via "Start" menu), after which you see a login window into the "Events Reader" SW containing the following fields (Fig. 19): Language selection of the desired language of interface display; COM-port - selection of a COM-port, which the dosimeter is connected to; PIN code - entering a PIN code to access the program.

36 36 Note You may get to know the COM-port number by clicking the right mouse button on the icon "Computer" and selecting "Properties" in the popup window. Then in the left side of the window that appears, select "Device Manager" item and in the "Ports (COM and LPT)" tab find "ST Microelectronics Virtual COM Port". COM-port (COM ) number specified opposite the device is used to select the login window to "Events Reader" SW in the "COM-port" field. If you connect the dosimeter to the same USB-port of the PC each time, the number of its COM-port does not change. An example of access to information about the COM-port number is provided for Windows 7 and may vary in other operating systems. Figure 19 Login window in "Events Reader" SW Select the desired options, enter a PIN code and click "Apply" button. If all data was entered correctly, the main window of the "Events Reader" program opens ( ). If a window appears with a warning that your data is incorrect, check the entered data and click "Apply" again.

37 Events reading After starting the "Events Reader" SW the main window s tab "Events" opens (Fig. 20). Figure 20 "Events" tab In the upper left corner of the "Events" tab a serial number of the connected dosimeter is highlighted in the format "Ser.number ХХХХХХХХ", where ХХХХХХХХ is a unique serial number of the currently connected dosimeter. This tab has the following fields as well: List of events - this field displays the events downloaded from the dosimeter during the last readout session ( ); Events Filter - in this field you can select the type and the date of events that will be displayed in the list after reading from the dosimeter ( ). Click "Read events" to read all events stored in the dosimeter s memory. IMPORTANT! Even if not all types of events were selected in the "Events Filter" field, they still would be read again each time until cleared from the dosimeter s memory ( ).

38 Working with the readout events After successful reading of the events from the dosimeter ( ) they are displayed in the "List of Events" field of the "Events" tab (Fig. 21). Figure 21 Readout events Select the required event in the "List of events" field. The information it contains is displayed rightwards below the "Events Filter" field. If you need to sort the downloaded events, you can check the boxes in the "Events Filter" field opposite those types of events to be displayed in the "List of Events" field. You can also set the time interval to display the events, the date of creation of which falls within this interval. To do this you have to check the box opposite the fields "from" and "to" and set the desired time interval. After selecting the types of events and/or the time interval, click "Apply" to display the events according to the specified parameters. "Clear events" button is designed to delete all events from the dosimeter s memory. IMPORTANT! If the events were not stored on the PC s hard drive (or removable disc), they are not subject to recovery after removal from the dosimeter s memory.

39 39 The upper right corner of the "Events" tab contains the following buttons of the events control: - saving all events to the PC s hard drive in the.dat format (including those that are not displayed according to filters); - download the saved events from the PC s hard drive; - save all events to the PC s hard drive in.html format; - printout the report; - display the event on the map, according to the coordinates where it was saved (if the coordinates have been added, ) (Fig. 22). Figure 22 Event display on the map

40 Settings Proceed to the "Settings" tab of the main window the "Events Reader" SW (Fig. 23) and click "Read settings" to readout the current data from the dosimeter. Figure 23 Settings tab "Settings" tab includes the following fields: Serial No. - this field displays the unique serial number of the connected dosimeter; Sigma threshold by gamma - set the threshold of alarm triggering in this field by the number of rms deviations of gamma radiation pulse count rate; Conditional threshold by neutrons - in this field you can set the threshold of the alarm triggering by the neutrons count rate; Safety threshold by gamma - in this field you can set the threshold of the alarm triggering by gamma radiation DER level; Date/Time - in this field you can enter the current date and time or check the box in the "Synchronization" line and click "Update" to read the system time from the PC. After entering the required data, click "Save settings" to record the updated data in the dosimeter s memory.

41 PIN code change To change the PIN code of access to "Events Reader" SW and login as the "Administrator" in the dosimeter, click on the "Change PIN code" button on the right side of the "Settings" tab of the "Events Reader" SW s main window (Fig. 24). A field of the PIN code change opens featuring the following fields (Fig. 24): Figure 24 PIN code change PIN code - enter the current access PIN code in this field; New PIN code - enter a new access PIN code in this field; Repeat new PIN code - renter the new access PIN code in this field. Click "Apply" to save the new PIN code or "Cancel" to keep the current PIN code unchanged.

42 Map On the "Map" tab of the "Events Reader" SW s main window you can view all points on the map downloaded during the last reading according to the coordinates where they were saved (Fig. 25). Figure 25 Map tab Completion of operation in the mode of data communication with PC After completion of work and exiting the "Events Reader" SW, the dosimeter automatically turns off and switches to the charging mode until it is disconnected from the PC.

43 43 3 TECHNICAL MAINTENANCE 3.1 Technical maintenance of the dosimeter General guidelines The list of operations during technical maintenance (hereinafter - TM) of the dosimeter, the order of priority and features at different stages of the dosimeter use is shown in Table 3.1. Table List of operations during technical maintenance Operations External examination Delivery kit completeness check Operability check Storage battery status control Verification of the dosimeter Type of technical maintenance during during everyday periodica long-term use l use storage OM item No Notes 1 + means the operation is applicable at this type of TM; - means the operation is not applicable. 2 The dosimeters should be verified after manufacture and repair Safety measures TM safety measures fully comply with safety measures presented in OM TM procedure of the dosimeter External examination Examination of the dosimeter should be performed in the following order: а) check the condition of the dosimeter s surfaces, the integrity of seals, absence of scratches, traces of corrosion, and surface damage of the coating; b) check the condition of the USB socket contacts Delivery kit completeness check Check if the delivery kit is complete according to Table Operability check of the dosimeter Operability check of the dosimeter and its procedure are performed according to OM

44 Storage battery status control The dosimeter s battery status control is performed during daily use, and before the long-term storage of the dosimeter. Follow the next procedure: - Switch on the dosimeter; - Monitor the battery s state-of-charge by the indicator on the display; - If the battery is not full, charge it by plugging the charger in the USB socket. 3.2 Verification of the dosimeter The dosimeters should be verified immediately after manufacture, during use (periodic verification at least once a year), as well as after repair Verification operations During verification the operations presented in Table 3.2 should be performed. Table Verification operations Operations Verification technique No. 1 External examination Testing Calculation of the main relative permissible error limit during gamma radiation DER measurement

45 Verification facilities The following facilities that should be used for verification are given in Table 3.3: Table 3.3 Name УПГД-3Б standard equipment УКПН-1М working standard unit of neutron radiation Aspiration psychrometer МВ- 4М Control aneroid barometer М- 67 RKS-01 STORA gamma, beta radiation radiometerdosimeter Regulatory documents or technical specifications Ambient dose equivalent rate of gamma radiation in the range from 0.1 to 10 6 µsv/h. Energy range from 59 kеv to 1.25 MeV. Main relative permissible error limit of gamma radiation DER and DE 4 % with confidence probability of 0.95 Thermal neutron flux density in the range from 10 to 500 cm -2 s -1. Main relative permissible error limit of thermal neutron flux density with confidence probability of %. Л ПС. Temperature measurement range from 30 to С. Temperature measurement error С. Relative humidity measurement range from 10 to 100 %. Relative error of relative humidity measurement in the range from 12 % at t = 10 0 С to 2 % at t = С. Л ПС. Pressure measurement range from 81.3 to kpа (from 610 to 790 mmhg). Pressure measurement error limit is kpа (0.8 mmhg) ТУ У Gamma radiation DER measurement range from 0.1 to 1000 µsv/h. 2. Main relative permissible error limit of gamma radiation DER with the energy of MeV is 15 % at Р=0.95. Notes 1. All verification facilities are to be tested and verified according to the requirements of national standards DSTU and DSTU 2708: The use of other items of measuring equipment that meet the prescribed accuracy is also applicable.

46 Verification conditions The verification test should be carried out under the following conditions: - ambient air temperature within (20±5) С; - relative air humidity within (65±15) %; - atmospheric pressure from 84 kpa to kpa; - natural gamma radiation background should not exceed 0.25 µsv/h; - the dosimeter s power supply from the newly charged storage battery Verification procedure External examination During external examination the dosimeter should meet the following requirements: - the delivery kit should be completed as described in OM 1.3; - labeling should be accurate; - Quality Control Department seals should not be violated; - the dosimeter should be free from mechanical damage that may affect its performance. Note The delivery kit of the dosimeter is checked only at manufacture Testing Switch on the dosimeter according to OM and proceed to calibration relative to gamma background Place the 137 Cs standard spectrometry gamma sources near the dosimeter and observe the increase of pulse count rate from the gamma radiation detector above the background level, and alarm triggering when an automatically set search threshold level is exceeded Place the dosimeter in the УКПН-1М carriage holder so that the mechanical center of neutron radiation beam coincides with the one of the dosimeter. Place the УКПН-1М carriage holder with the dosimeter in the position, where neutron radiation from 239 Pu-Be ensures pulse count rate from the neutron radiation detector within a s -1 range. Make sure that the alarm of neutron radiation is triggered Switch off the dosimeter according to OM Calculation of the main relative permissible error limit during gamma radiation DER measurement Prepare the testing equipment УПГД-3Б according to its Operating Manual. Place the dosimeter in the УПГД-3Б carriage holder so that the mechanical center of gamma beam coincides with the mechanical center of the dosimeter s gamma detector.