TC TC500-X...Proportional TC1000-X...Proportional TC500-D...3-Position TC1000-D...3-Position. Electric Actuator

Transcription

1 Datasheet No.: TC TC500-X...Proportional TC000-X...Proportional TC500-D...3-Position TC000-D...3-Position Electric Actuator Suitable for valve stroke 20mm. Rating force 500N/000N TC500-X.../ TC000-X... : proportional control type, 0(2)~0VDC, many kinds of control signals TC500-D.../ TC000-D... : 3-position control type Max. force can reach 700N/200N 24VAC/ 220VAC can be selected Alternating current magnet synchronous motor,fixed torque output force. Input/valve position signals: 0(2)~0VDC and (only proportional) Valve position signals: 0-0K resistance, SPDT or active signal available (only 3-position) PCB is made of 32bit signalchip + embedded operating system, adopt SMT paster welding technology,precision of the electronic pieces using first-class brand home and aboard is %. PCB has a function with defend wrong connection. Application Proportional control type has self-adaption function which can automatic testing the max stroke of valve. These actuators are used in 2-port, 3-port valve (TL/TF/TFR/TTF...series), whose stroke is 22 mm. Environment temperature: -0~60 Permissible medium temperature: -25~+50 (water valve) / 2~+80 (steam valve) Functions 2~+220 (high temperature steam valve) /2~+450 (super-high temperature steam valve) Note: when temperature of medium is below 0,e.g.refrigerant(R2,R22,R34a,R202),glycol, stem heater(thot-/ THOT-2) can be used to avoid connection part frosting or freezing. Proportional type TC500-X... / TC000-X... Control singnal: 0(2)~0VDC, TC500-X.../TC000-X... realize controlling by terminal O,E signal Control singal at terminal O,E increasing: the actuator shaft extends, and valve stem retracts Control singal at terminal O,E decreasing: the actuator shaft retracts, and valve stem extends Control singal at terminal has no changing: the actuator shaft and valve stem stays in present position Notes:.This DA mode was made before leaving factory, if RA mode needed(control signal increases, actuator shaft retracts), just put the 5th switch of from to. 2. Pay attention to relationship between valve stem and valve opening,closing. Tiger Controls globe valve is: valve stem retracts, valve opens. PICV is: valve stem retracts,valve closes

2 3-position control type Voltage on terminal and 2: the actuator shaft extends, and valve stem retracts TC500-D.../ TC000-D.. Voltage on terminal and 3: the actuator shaft retracts, and valve stem extends 3-position control signal No voltage on terminal,2 and,3: the actuator shaft and valve stem stays in present position Ordering and Transportation When ordering, please give clear indication on products type reference and any accessories required, such as: TC500-X24-S.2. Actuator, valve body and accessories are supplied in seperated packages. Combination device TC500/TC000...electric actuator can be fitted with 2-port, 3-port TL...,TF... series valve body whose stroke is less than 20mm. Mechanical Design Type DN (mm) PN(Mpa) Datasheet No. 2-port TL series / 2.5 optional TL-02 TF series / 2.5 optional TF-02 TFR...series / 2.5 optional TFR-02 TTF...series / 2.5 optional TTF-02 Actuator have long service time without repairing TC500/TC000...actuator with AC magnet synchronous motor Limit force mechanical part was designed in order to protect the other part from overloading TC500-X/D.../ TC000-X/D actuator has function of outage at limit position Manual device is standard configuration Flow character Equal-linear flow characteristic. The relationship between control signal0(2)~0vdc, and flow is shown in the belowing figure: medium flow 00% equal-linear curve control signal 00% 2

3 Debugging Description A. Connect actuator and valve body. B. Turn off power of actuator. C. power and control signal wires. D. Set dip switch to needed position. After the setting,turn on power of actuator,setted function will come into effect.(dip switch can be setted with power) E. Turn on the power of actuator. F. Actuator self-stroking: this step is for matching stroke of actuator and valve. () Running light on PCB will keep flickering( frequency is Hz),actuator shaft extends to down limited positon firstly, and then retracts to up limited position.(actuator will not be controlled by signal now) (2) Running light stops flickering after 3 minutes of self-stroking. Self-stroking stops. By then, actuator running direction can be controlled by control signal. Remarks: If self-stroking is needed when power on, press down the red button on PCB over 3 seconds until the running light flickering. Self-stroking phenomenon are the same as step (2), (3) above. G.Kvs adjustment. By aperture potentiometer, max. aperture can be setted from 00% to 30%. Ralationship between relative flow and opening can be adjusted flexibly.00%-40% opening has high and low sensitivity. 40%~30% opening only has low sensitivity. Note:. The factory default setting is automatic self-stroking,it means that actuator will repeat automatic self-stroking when power on each time. Type Summary 2.If you don't need automatic self-stroking function,you can set the 7th switch to. It will change into manual self-stroking(phenomenon as same with (),(2). 500N actuator Type Type Description Rating Force Actual Output Force Operating Voltage Control Feedback Running Time (50Hz) Diagram 000N actuator TC500-X24-S.2 Proportional 500N 500N~700N 24VAC 0(2)~0VDC TC500-X220-S.2 Proportional 500N 500N~700N 220VAC 0(2)~0VDC 0(2)~0VDC 0(2)~0VDC Diagram Diagram 2 TC500-D24-S.2 3-position 500N 500N~700N 24VAC 3-position No TC500-D220-S.2 3-position 500N 500N~700N 220VAC 3-position No TC500-D24-SF0K.2 TC500-D220-SF0K.2 TC500-D24-SF2.2 TC500-D220-SF2.2 TC500-D24-SF3.2 TC500-D220-SF3.2 Type 3-position with 0-0K resistance 3-position with 0-0K resistance 3-position with 2 SPDT 3-position with 2 SPDT 3-position with active signal 3-position with active signal Type Discription 500N 500N~700N 24VAC 3-position 500N 500N~700N 220VAC 3-position 500N 500N~700N 24VAC 3-position 500N 500N~700N 220VAC 3-position 0-0K resistance 0-0K resistance 2 SPDT 2 SPDT 500N 500N~700N 24VAC 3-position active signal Diagram 6 500N 500N~700N 220VAC 3-position active signal Diagram 6 Rating Force Actual Output Force Operating Voltage Control Feedback Running Time (50Hz) Diagram TC000-X24-S.2 Proportional 000N 000N~200N 24VAC 0(2)~0VDC TC000-X220-S.2 Proportional 000N 000N~200N 220VAC 0(2)~0VDC 0(2)~0VDC 0(2)~0VDC Diagram Diagram 2 TC000-D24-S.2 3-position 000N 000N~200N 24VAC 3-position No TC000-D220-S.2 3-position 000N 000N~200N 220VAC 3-position No TC000-D24-SF0K.2 TC000-D220-SF0K.2 TC000-D24-SF2.2 TC000-D220-SF2.2 TC000-D24-SF3.2 TC000-D220-SF3.2 3-position with 0-0K resistance 3-position with 0-0K resistance 3-position with 2 SPDT 3-position with 2 SPDT 000N 000N~200N 24VAC 3-position 000N 000N~200N 220VAC 3-position 000N 000N~200N 24VAC 3-position 000N 000N~200N 220VAC 3-position 0-0K resistance 0-0K resistance 2 SPDT 2 SPDT 3-position with 000N 000N~200N 24VAC 3-position active signal active signal Diagram 6 3-position with 000N 000N~200N 220VAC 3-position active signal active signal Diagram 6 3

4 Diagram M M B O O E Y Control signal power Feedback signal L N O E Y AC220V Controls signal Feedback signal diagram: proportional (24VAC) diagram 2: proportional (220VAC) M 2 3 Power Power Terminal Shaft -2 extent -3 retract Terminal Actuator axes -2 extend restract Feedback resistence K 0 0 0K 0 0K 0K 0 diagram3: 3-position diagram4: 3-position with 0~0K DOWN UP 2 3 COM DOWN UP Power Power COM NO COM NO 2 3 COM DOWN UP Power Power DL UL diagram 5: 3-position with SPDT diagram 6: 3-position with active signal 4

5 The PCB of Proportional type Actuator Switch self-stroking button S aperture potentiometer connecting terminal B O O E Y power light running light 20% II UI IO 0 UI II UO DA DW DF HS RA UP RF LS PCB diagram : Proportional type (24VAC) TC500-X24../ TC000-X24.. switch self-stroking button aperture potentiometer power light connecting terminal running light The, switch setting of Proportional type Actuator PCB diagram 2: Proportional type (220VAC) TC500-X220../ TC000-X220.. Switch Function Description Starting of control/ signal 20%:the starting control / signal is 20% (namely 4~20mA or 2~0V) 0:the starting control / signal is 0 (namely 0~20mA or 0~0V) The setting of, switch Type of control signal Impedence match of control signal Type of signal II: current signal UI: voltage signal UI: voltage signal II: current signal IO: current signal UO: voltage signal Operating mode 2 Losing control signal mode 3 Self-stroking mode DA:DA mode (when control signal increases, the actuator shaft extends ) RA: RA mode (when control signal increases, the actuator shaft retracts) DW: When lose control signal (voltage type), actuator will provide a min. control signal internally When lose control signal (current type), actuator will provide a min. control signal internally UP: When lose control signal (voltage type), actuator will provide a max. control signal internally When lose control signal (current type), actuator will provide a min. control signal internally DF: Power on each time, self-stroking starts automatically (factory setting) RF: self-stroking starts only when press the red self-stroking button manually 4 Sensitivity HS: the high sensitivity of control signal %(00%~40%);.5%(40%~30%) LS: the low sensitivity of control signal.5%(00%~30%) 5

6 .Dip switch sample when matched with electric control valve. Nominal setting of, switch Control signal: 0~0VDC; Feedback signal: 0~0VDC; DA mode(factory setting); When lose control signal (voltage type), means input a minimum control signal, the actuator shaft retracts. Control signal: 4~20mA; Feedback signal: 4~20mA; DA mode; When lose control signal (current type), means input a minimum control signal, the actuator shaft retracts. 2.When matched with pressure independent control valve,the fifth dip switch is, other dip switch is the same with electric control valve. Proportional actuator Opening adjustment potentiometer maximum opening 00 Dimensions By aperture potentiometer, max. aperture can be setted from 00% to 30%. Flexibly adjust the relationship between the relative flow and opening of valve body, the factory default value is 00%. Mounting Orientation Medium is chilled/hot water Installation downwards is forbidden Medium is steam Random direction is OK 6

7 Installation Sheet Prepare for assembling the actuator, take 2 down the sliding block firstly, and then disentangle the clip. Keep the actuator s axes and the valve s stem concentric.make these two connectiong faces coinciding. Then lock the two screws on the clip. Observation hole 3 Pull the sliding block to the groove and lock it 4 by two screws. The status after assembled. Technology Data Eelectric parameter Electric Motor synchronous motor with permanent magnetic Operating Voltage TC500-X24.../ TC000-X24... TC500-X220.../ TC000-X Frequency 24VAC ± 5% 220VAC ± 5% 50Hz or 60Hz available Power consumption TC500/000-D.../F0K/F3... TC500/000-D...F2... TC500/000-X VA 7.5VA 7.5VA Impedance(only for proportional type) voltage input impedance current input impedance >00K <0.67K Function Parameter Load requirements (only for proportional type) voltage output load requirement current output load requirement >K <0.5K Up and down dead band Sensitivity 2% %;.5% Control type TC500-D.../ TC000-D... TC500-X.../ TC000-X... 3-position proportional Control TC500-D.../ TC000-D... TC500-X.../ TC000-X... 24VAC/ 220VAC 0(2)~0VDC, 7

8 Environment Condition Feedback TC500-X.../ TC000-D... TC5000-D.../TC000-D... TC500/000-D..-F0K TC500/000-D..-F2 TC500/000-D..-F3 IP degree 0(2)~0VDC, no 0-0K resistance SPDT active signal IP54 Permissible medium temperature -25~+30 (water) /2~+80 (steam) 2~+220 (high tempreature steam valve)/ 2~+450 (super-high tempreature steam valve) Notes:. When medium temperature below 0 (R2, R22, R34a, R202, glycol), the stem of the valve should be protected by electric heating cover(thot-/thot-2) to avoid frosting and icing. Running Enviroment tempreture: Enviroment humidity: Transportation Enviroment tempreture: Enviroment humidity: -0~+60 (3-position type) 95% RH -30~+65 95% RH Storage Enviroment tempreture: Enviroment humidity: -5~+50 95% RH Material Cover Bracket PC die casting aluminum(surface anti-rust process) Dimension and Weight Product Dimensions Weight refer to the dimension figure.7kg Lifetime Lifetime 00 thousand times Certificate Certificate CE,RoHS,REACH 8

9 Datasheet No.: TR800/ Electric Actuator TR800/3000-D...Series TR800/3000-X...Series TR5000-D...Series TR5000-X...Series Stroke 40mm. Rating force 800N/ 3000N/5000N TR800-X.../ TR3000-X... /TR5000-X...: proportional control type, many kinds of control signal: 0(2)~0VDC, TR800-D.../ TR3000-D./TR5000-D...: 3-position control type Max. actual force: 2000N/3500N/5500N 24VAC/220VAC can be selected Visible window, PCB status can be seen clearly LED display module can display the percentage of control signal and valve position signal and relative alarm information. 0-K resistance,0-0k resistance, SPDT are optional(only 3-position) Control signals: 0(2)~0VDC and (only proportional control type) PCB is made of 32bit signalchip + embedded operating system, adopt SMT paster welding technology,precision of the electronic pieces using first-class brand home and aboard is %. PCB has a function with defend wrong connection. Application Selfstroke for proportional control type can automatic testing the max stroke of valve. These actuators used in 2-port, 3-port valve (TL/TF/TFR/TTF...series), whose stroke is less than 44mm. Environment temperature: -0~60 Permissible medium temperature: -25~+50 (water valve) / 2~+80 (steam valve) /2~+220 (high temperature steam valve) / 2~+450 (super-high temperature steam valve) Notes: Functions Proportional type TR800-X... /TR3000-X... /TR5000-X... Control singnal/ vale signal: 0(2)~0VDC, When medium temperature below 0 (R2, R22, R34a, R202, glycol), the stem of the valve should be protected by stem heater (THOT-/THOT-2) to avoid frosting and icing. TR800-X.../TR3000-X.../TR5000-X... realize controlling by terminal O,E signal Control singal at terminal O,E increasing: the actuator shaft extends, and valve stem retracts Control singal at terminal O,E decreasing: the actuator shaft retracts, and valve stem extends Control singal at terminal has no changing: the actuator shaft and valve stem stays in present position Notes:.This DA mode was made before leaving factory, if RA mode needed(control signal increases, actuator shaft retracts), just put the 5th switch of from to. 2. Pay attention to relationship between valve stem and valve opening,closing. Tiger Controls globe valve is: valve stem retracts, valve opens. PICV is: valve stem retracts,valve closes. 9

10 3-position control type TR800-D... / TR3000-D... Voltage on terminal and 2: the actuator shaft extends, and valve stem retracts / TR5000-D... Voltage on terminal and 3: the actuator shaft retracts, and valve stem extends 3-position control signal No voltage on interminal,2 and,3: the actuator shaft and valve stem stays in present position Ordering and Transportation When ordering, please give clear indication on products type and accessories required, such as: TR800-X24-S.2. Actuator and valve body are supplied in separated packages. Combination device TR800/TR3000/TR electric actuator can be fitted with 2-port, 3-port TL...,TF... series valve body whose stroke is less than 40mm. Type DN (mm) PN(Mpa) Datasheet No. TL series / 2.5 optional TL-02 TF... series / 2.5 optional TF-02 TFR... series / 2.5 optional TFR-02 TTF...series / 2.5 optional TTF-02 Mechanical Design Actuator have long service time without repair TR800/TR3000/TR actuator with synchronous motor TR800-D.../ TR3000-D.../TR5000-D actuator have limit switch Manual device is standard configuration Flow character Linear flow characteristic. The relationship between control signal and flow is shown in the belowing figure: medium flow 00% equal-linear curve control signal 00% 0

11 Debugging A. Connect actuator and valve body. B. Turn off power of actuator. C. power and control signal wires. D. Set dip switch to needed position. After the setting,turn on power of actuator,setted function will come into effect.(dip switch can be setted with power) E. Turn on the power of actuator. F. Actuator self-stroking: this step is for matching stroke of actuator and valve. () Running light on PCB will keep flickering( frequency is Hz),actuator shaft extends to down limited positon firstly, and then retracts to up limited position.(actuator will not be controlled by signal now) (2) Running light stops flickering after 5 minutes of self-stroking. Self-stroking stops. By then, actuator running direction can be controlled by control signal. Remarks: If self-stroking is needed when power on, press down the red button on PCB over 3 seconds until the running light flickering. Self-stroking phenomenon are the same as step (2), (3) above. G.Kvs adjustment. By aperture potentiometer, max. aperture can be setted from 00% to 30%. Ralationship between relative flow and opening can be adjusted flexibly.00%-40% opening has high and low sensitivity. 40%~30% opening only has low sensitivity. Type Summary Note:. The factory default setting is automatic self-stroking,it means that actuator will repeat automatic selfstroking when power on each time. 2.If you don't need automatic self-stroking function,you can set the 7th switch to. It will change into manual self-stroking(phenomenon as same with (),(2). 800N actuator Type Type Discription Rating Force Actual Output Force Operating Voltage Control Feedback Running Time (50Hz) Diagram TR800-X24-S.2 Proportional 800N 800N~2000N 24VAC 0(2)~0VDC TR800-X220-S.2 Proportional 800N 800N~2000N 220VAC 0(2)~0VDC 0(2)~0VDC 0(2)~0VDC Diagram Diagram 2 TR800-D24-S.2 3-position 800N 800N~2000N 24VAC 3-position No TR800-D220-S.2 3-position 800N 800N~2000N 220VAC 3-position No TR800-D24-SFK.2 TR800-D220-SFK.2 TR800-D24-SF0K.2 TR800-D220-SF0K.2 TR800-D24-SF2.2 3-position with 0-K resistance 800N 800N~2000N 24VAC 3-position 0-K resistance 3-position with 0-K resistance 800N 800N~2000N 220VAC 3-position 0-K resistance 3-position with 0-0K resistance 800N 800N~2000N 24VAC 3-position 0-0K resistance 3-position with 0-0K resistance 800N 800N~2000N 220VAC 3-position 0-0K resistance 3-position with 2 SPDT 800N 800N~2000N 24VAC 3-position 2 SPDT Diagram N actuator Type Type Discription Rating Force Actual Output Force Operating Voltage Control TR3000-X24-S.2 Proportional 3000N 3000N~3500N 24VAC 0(2)~0VDC TR3000-X220-S.2 Proportional 3000N 3000N~3500N 220VAC 0(2)~0VDC Feedback 0(2)~0VDC 0(2)~0VDC Running Time (50Hz) Diagram Diagram Diagram 2 TR3000-D24-S.2 3-position 3000N 3000N~3500N 24VAC 3-position No TR3000-D220-S.2 3-position 3000N 3000N~3500N 220VAC 3-position No TR3000-D24-SFK.2 TR3000-D220-SFK.2 TR3000-D24-SF0K.2 TR3000-D220-SF0K.2 TR3000-D24-SF2.2 3-position with 0-K resistance 3-position with 0-K resistance 3-position with 0-0K resistance 3-position with 0-0K resistance 3-position with 2 SPDT 3000N 3000N~3500N 24VAC 3-position 3000N 3000N~3500N 220VAC 3-position 3000N 3000N~3500N 24VAC 3-position 3000N 3000N~3500N 220VAC 3-position 3000N 3000N~3500N 24VAC 3-position 0-K resistance 0-K resistance 0-0K resistance 0-0K resistance 2 SPDT Diagram 6

12 5000N actuator Type Type Discription Rating Force Actual Output Force Operating Voltage Control Feedback Running Time (50Hz) Diagram Diagram TR5000-X24-S.2 Proportional 5000N 4500N~5500N 24VAC 0(2)~0VDC TR5000-X220-S.2 Proportional 5000N 4500N~5500N 220VAC 0(2)~0VDC 0(2)~0VDC 0(2)~0VDC Diagram Diagram 2 TR5000-D24-S.2 3-position 5000N 4500N~5500N 24VAC 3-position No TR5000-D220-S.2 3-position 5000N 4500N~5500N 220VAC 3-position No TR5000-D24-SFK.2 TR5000-D220-SFK.2 TR5000-D24-SF0K.2 TR5000-D220-SF0K.2 TR5000-D24-SF2.2 3-position with 0-K resistance 3-position with 0-K resistance 3-position with 0-0K resistance 3-position with 0-0K resistance 3-position with 2 SPDT 5000N 4500N~5500N 24VAC 3-position 5000N 4500N~5500N 220VAC 3-position 5000N 4500N~5500N 24VAC 3-position 5000N 4500N~5500N 220VAC 3-position 5000N 4500N~5500N 24VAC 3-position 0-K resistance 0-K resistance 0-0K resistance 0-0K resistance 2 SPDT Diagram 6 M M B O O E Y Control signal power Feedback signal L N O E Y AC220V Controls signal Feedback signal diagram: proportional (24VAC ) diagram 2: proportional (220VAC) Electricity terminals shaft - 2 extend - 3 retract K resistance K 0 K K 0 diagram3: 3-position diagram4: 3-position with K Electricity terminals shaft - 2 extend - 3 retract resistance K 0 0 0K 0 0K 0K 0 diagram 5: 3-position with 0K diagram 6: 3-position with SPDT 2

13 The PCB Figure of Proportional type Actuator CPU self-stroking button S 20% II UI IO 0 UI II UO DA DW DF HS RA UP RF LS error light aperture potentiometerr ERR maximum 00 RUN opening running light function digit number digit 24VAC auxiliary terminal UL DL AL B O O E Y connecting terminal PCB diagram : Proportional type (24VAC) TR800-X24../ TR3000-X24.. / TR5000-X24.. CPU self-stroking button S 20% II UI IO 0 UI II UO DA DW DF HS RA UP RF LS error light aperture potentiometer ERR maximum RUN 00 opening running light function digit number digit 220VAC L N O E Y The, switch setting of Proportional type Actuator auxiliary terminal UL DL AL connecting terminal PCB diagram 2: Proportional type (220VAC) TR800-X220../ TR3000-X220../ TR5000-X220.. Switch Function Description Starting of control/ signal 20%:the starting control / signal is 20% (namely 4~20mA or 2~0V) 0:the starting control / signal is 0 (namely 0~20mA or 0~0V) 2 3 Type of control signal Impedence match of control signal II: current signal UI: voltage signal UI: voltage signal II: current signal 4 Type of signal IO: current signal UO: voltage signal Operating mode DA:DA mode (when control signal is increasing, the actuator axes extends ) RA: RA mode (when control signal is increasing, the actuator axes retracts) 2 Losing control signal mode DW: When lose control signal (voltage type), actuator will provide a min. control signal internally When lose control signal (current type), actuator will provide a min. control signal internally UP: When lose control signal (voltage type), actuator will provide a max. control signal internally When lose control signal (current type), actuator will provide a min. control signal internally 3 Self-stroking mode DF: Power up each time, self-stroking starts automatically (factory setting) RF: self-stroking starts only when press the red self-stroking button manually 4 Sensitivity HS: the high sensitivity of control signal %(00%~40%);.5%(40%~30%) LS: the low sensitivity of control signal.5%(00%~30%) 3

14 44 Nominal setting of, switch.dip switch sample when used with electric control valve. Control signal: 0~0VDC; Feedback signal: 0~0VDC; ( factory setting) DA mode; When lose control signal (voltage type), means input a minimum control signal, the actuator shaft retracts. Control signal: 4~20mA; Feedback signal: 4~20mA; DA mode; When lose control signal (current type), means input a minimum control signal, the actuator shaft retracts. 2.When used with Pressure independent control valve,the fifth dial code is,other dip switch are the same with electric control valve. Proportional actuator Opening adjustment potentiometer maximum opening 00 Dimensions By aperture potentiometer, max. aperture can be setted from 00% to 30%.Flexibility adjust the relationship between the relative flow and opening of valve body,the factory default value is 00%. Mounting Orientation Medium is chilled/hot water Medium is steam Installation downwards is forbidden random direction is OK 4

15 Installation Sheet.Prepare for assembling the actuator, take down the fixed litting stly,and then disentangle the clip. 2.Keep the actuators s axis and valve s stem concentric. Make these two connecting faces keep coinciding and Observe by observation hole.put the actuator on the convex platform of valve body.then lock the two screws on the clip. Observation hole 3.Full the fixed litting to the grooved and lock by two screws. 4.The status after assembled Technology Data Electric Parameter Electric Motor Synchronous motor with permanent magnetic Operating Voltage TR800-X24.../ TR3000-X24.../TR5000-X24.. TR800-X220.../ TR3000-X220.../TR5000-X220 24VAC± 5% 220VAC± 5% Frequency 50Hz or 60Hz available Power consumption TR800/3000/5000-D... TR800/3000/5000-D...FK/F0K/F2... TR800/3000/5000-X... 3VA 3VA 5VA Impedance (only for proportional type) voltage input impedance current input impedance >00K <0.67K Function Parameter Load requirements (only for proportional type) voltage output load requirement current output load requirement Up and down dead band Sensitivity >K <0.5K 2% %.5% Control type TR800-X.../TR3000-X.../TR5000-X... TR800-D.../TR3000-D.../TR5000-D... proportional 3-position 5

16 Control TR800-X.../TR3000-X.../TR5000-X... TR800-D.../TR3000-D.../TR5000-D... 0(2)~0VDC, 24VAC/220VAC Feedback TR800-X.../TR3000-X.../TR5000-X... TR800-D.../TR3000-D.../TR5000-D.. TR800/3000/5000-D...-SF0K.2 TR800/3000/5000-D..-SF0K.2 TR800/3000/5000-D..-SF2.2 0(2)~0VDC, no 0-K resistance 0-0K resistance SPDT Environment Condition IP degree IP54 Permissible medium temperature -25~+50 (water)/2~+80 (steam) 2~+220 (high tempreature steam valve) /2~+450 (super-high tempreature steam valve) Notes:. When medium temperature is below 0 (R2, R22, R34a, R202, glycol), the stem of the valve should be protected by electric heating cover(thot-/thot-2) to avoid frosting and icing. Running Enviroment tempreture: Enviroment humidity: -0~+60 95% RH Transportation Enviroment tempreture: Enviroment humidity: -30~+65 95% RH Storage Enviroment tempreture: Enviroment humidity: -5~+50 95% RH Material Cover Bracket Gear aluminum die casting aluminum die casting(surface anti-rust process) metal gear Product Dimensions Weight refer to the dimension figure 5.2Kg Lifetime 00 thousand times certificate CE, RoHS, REACH 6