Applicant: PAUL K GUILLOW INC Date: May 23, NEW SALEM STREET P O BOX 229 WAKEFIELD MA USA

Transcription

1 Applicant: PAUL K GUILLOW INC Date: May 23, NEW SALEM STREET P O BOX 229 WAKEFIELD MA USA Attn: DALE BASS Submitted sample said to be : Item Name : (1) Copter Toys (2) Sky Raider (3) Space Shuttle Item No. : (1) 11 (2) 2645 (3) 2650 Quantity : Four sets each Labelled Age Group : (1) "8+" (2) & (3) "Ages 8 and up" Packaging Provided : Yes Vendor : Paul K. Guillow, Inc. Buyer : Paul K. Guillow, Inc. Country of Origin : USA ****************************************************************************************************************************************** For and on behalf of : Intertek Testing Services HK Ltd. Angel Y.F. Cheung Vice President Page 1 of 32

2 Conclusion: The submitted sample was tested under the following requirements requested by the applicant, subject to the information stated in the remark and attached page(s) for details : Requirement (1) U.S. CFR Title 16 (CPSC Regulations) - mechanical and physical tests Sharp point Sharp edge 1501 Small part (2) U.S. CFR Title 16 (CPSC Regulations) - Part (c)(6)(vi) - Flammability test on rigid and pliable solids (3) U.S. ASTM F Physical and Mechanical tests excluding requirement of section 4.12 and (4) ASTM F Flammability Test of Materials other than textile materials (5) ASTM F Total Lead content (6) ASTM F Soluble heavy elements test (7) U.S. Consumer Product Safety Improvement Act 2008 Title I Section Total Lead content in non-surface coating materials (substrate) (8) U.S. CFR Title 16 (CPSC Regulations) - Part Total Lead content in surface coating U.S. Consumer Product Safety Improvement Act 2008 Title I Section Total Lead content in surface coating (9) U.S. Consumer Product Safety Improvement Act 2008 Title I, Section Phthalate content (10) Consumer Product Safety Improvement Act (CPSIA) 2008 Section Tracking labels for children products (11) California Proposition 65 for toys, Consent Judgement no. RG Lead content (12) California Proposition 65 for Toys (designed for or reasonable used by children under six years of age), Consent judgment no. BG Phthalate content Result Not Applicable Not Applicable (13) Model Toxics in Packaging Legislation (packaging materials) - Toxic elements test Page 2 of 32

3 Requirement (14) EN71-1: Mechanical and Physical Properties excluding the requirements of clause (c) and 6 (15) EN71-2 : A1 : Flammability Test (16) EN71-3 : A1: Migration of certain elements (17) REACH Regulation (EC) no. 1907/2006 & amendment (EU) no. 1272/2013 Annex XVII Item 50 - Polycyclic aromatic hydrocarbons content (18) REACH Regulation (EC) no. 1907/2006, Annex XVII Items 51 & 52 & amendment no. 552/ Phthalates content (19) REACH Regulation (EC) no. 1907/2006, Annex XVII Item 61 & Amendment No. 412/2012 (formerly known as Directive 2009/251/EC) - Dimethylfumarate content requirement Result (20) Formaldehyde release See details enclosed (21) 94/62/EC and amendment 2013/2/EU & Directive (EU) 2015/720 Directive (packaging waste) - Toxic elements test (22) Regulation (EC) No. 850/2004 & amendment No.519/2012 and (EU) 2015/2030 on persistent organic pollutants (POPs) - Short Chain Chlorinated Paraffin (C10 - C13) (SCCP) content (23) REACH Regulation (EC) No.1907/2006, Annex XVII Item 23 & amendment No. 2016/217 - Cadmium content requirement (24) REACH Regulation (EC) No. 1907/2006, Annex XVII item 20 & amendment (EU) No. 276/2010 (formerly known as Decision 2009/425/EC) - Organotin content requirement (25) Regulation (EC) No. 850/2004 & amendment No.757/2010 on persistent organic pollutants (POPs), Annex I, Part A - Tetrabromodiphenyl Ether (TetraBDE), Pentabromodiphenyl Ether (PentaBDE), Hexabromodiphenyl Ether (HexaBDE) and Heptabromodiphenyl Ether (HeptaBDE) content (26) Regulation (EC) No. 850/2004 & amendment No.(EU) 2016/293 on persistent organic pollutants (POPs), Annex I, Part A - Hexabromocyclododecane (HBCDD) content (27) REACH Regulation (EC) No. 1907/2006, Annex VII, Item 45 & amendment No. 552/ Octabromodiphenyl Ether (OctaBDE) content Page 3 of 32

4 (1) Physical and Mechanical Test Test Standard : U.S. code of Federal Regulations Title 16 Part , the hazards of sharp points, sharp edge and small parts are assessed both before and after applicable use and abuse tests. Applicant's specified age group for testing : For Ages over 8 Years Remark: The physical and mechanical tests requirements of U.S. Consumer Products Safety Commission for toys and articles intended for use by the children specified in U.S. Code of Federal Regulations Title 16, Part , and 1501 are only for children under 8 years of age. Therefore, the submitted sample was found not applicable. Test Period : Apr 07, 2017 to Apr 22, 2017 (2) Flammability Tests Test Standard : U.S. Code of Federal Regulations Title 16 Part for rigid and pliable solids. Sample Ignition point Burn length (inch) Time (sec) Burn Rate (inch/sec) (inch/sec) Airplane Edge All styles of the submitted toy sample were tested, the above result only showed the most severe burn rate of the samples. Test Period : Apr 07, 2017 to Apr 22, 2017 Page 4 of 32

5 (3) Physical and Mechanical Tests Test Standard : ASTM Standard Consumer Safety Specification for Toy Safety F Applicant's specified age group for testing : For Ages over 8 Years Clause Requirement Assessment 4.1 Material quality P 4.5 Sound producing toys NA Toys intended for children under 36 months of age NA Mouth actuated toys NA Toys and games for 36 months to 72 months - Small part warning NA 4.7 Accessible edges NA 4.8 Projection NA 4.9 Accessible points NA 4.10 Wires or rods NA 4.11 Nails and fasteners P 4.12 Plastic film # Folding mechanisms and hinges NA 4.14 Cords, straps, and elastics NA 4.15 Stability and overload requirement NA 4.16 Confined spaces NA 4.17 Wheels, tires, and axles (96 months of age or less) NA 4.18 Holes, clearance, and accessibility of mechanisms NA 4.19 Simulated protective devices NA 4.20 Pacifiers NA 4.21 Projectile toys P# Teethers and teething toys NA 4.23 Rattles NA 4.24 Squeeze toys NA 4.25 Battery operated toys NA 4.26 Toys intended to be attached to a crib or playpen NA 4.27 Stuffed and beanbag type toys NA 4.28 Stroller and carriage toys NA 4.29 Art materials NA 4.30 Toy gun marking NA 4.31 Balloons NA 4.32 Certain toys with nearly spherical ends NA 4.33 Marbles NA 4.34 Balls NA 4.35 Pompoms NA 4.36 Hemispherical shaped objects NA 4.37 Yo Yo elastic tether toys NA 4.38 Magnets NA 4.39 Jaw Entrapment in Handles and Steering Wheels NA Page 5 of 32

6 Clause Requirement Assessment 4.40 Expanding materials NA 4.41 Toy chests NA 5 Labeling requirements P 6 Instructional literature P 7 Producer's marking - Name of producer / distributor Yes - Address Yes Abbreviation : P = NA = Not Applicable The submitted samples were undergone the tests in accordance with section 8.5 through section 8.17 and 8.19 through 8.26 on normal use, abuse and specific tests for different types of toys whichever is applicable. Remark(s): #1 = As requested by applicant, the requirement in section 4.12 for plastic film and for Rotor under Projectile was not assessed. and May 16, 2017 Test Period : Apr 07, 2017 to May 17, 2017 (4) Flammability Tests Test Standard : Section 4.2 of the ASTM Standard Consumer Safety Specification for Toy Safety F Sample Ignition point Burn length (inch) Time (sec) Burn Rate (inch/sec) (inch/sec) Airplane Edge The above result only showed the most severe burn rate of the samples and components. Test Period : Apr 07, 2017 to Apr 22, 2017 Page 6 of 32

7 (5) Total Lead (Pb) Content Test Method : Sections (1) and (2)(a) of the ASTM Standard Consumer Safety Specification for Toy Safety F963-16, CPSC-CH-E , CPSC-CH-E or/and CPSC-CH-E , analysed by Inductively Coupled Argon Plasma Spectrometry. Coating: Tested Component Result in ppm in ppm (1) <20 90 (2/3) <20 90 (4) <20 90 Substrate: Tested Component Result in ppm in ppm (5/6/7) < (8/9/10) < (11/12) < (13/14) < (15) < ppm = parts per million = mg/kg Tested Components: (1) Coatings on plastic label (sticker #2645). (2) Coatings (red, black) on foam (copter #11). (3) Coatings (blue, black) on foam (copter #11). (4) Coatings (green, black) on foam (copter #11). (5) Transparent plastic label excluding coatings (sticker #2645, copter #11). (6) White foam (space shuttle #2650, glider #2645). (7) Paper label with plastic film (sticker #2650). (8) Black plastic (frame of space shuttle #2650). (9) Orange plastic (launcher #2650). (10) Light brown elastic band (launcher #2650). (11) Dull black plastic (propeller #11). (12) Yellow plastic (hook and holder #11). (13) Transparent elastic band (holder #11). (14) Shiny light brown elastic band (loops #11). (15) Silver color metal (hook #11). Test Period : Apr 07, 2017 to Apr 18, 2017 Page 7 of 32

8 (6) Heavy Elements Analysis Test Method : Sections 8.3.2, 8.3.3, and of the ASTM Standard Consumer Safety Specification for Toy Safety F963-16, acid extraction and analysed by Inductively Coupled Argon Plasma Spectrometry. Materials other than modelling clay: Result (ppm) (1) (5) (6) (ppm) Soluble Barium (Ba) 120 <5 < Soluble Lead (Pb) <5 <5 <5 90 Soluble Cadmium (Cd) <5 <5 <5 75 Soluble Antimony (Sb) <5 <5 <5 60 Soluble Selenium (Se) <5 <5 <5 500 Soluble Chromium (Cr) <5 <5 <5 60 Soluble Mercury (Hg) <5 <5 <5 60 Soluble Arsenic (As) <2.5 <2.5 < Result (ppm) (7) (8) (9) (ppm) Soluble Barium (Ba) <5 <5 < Soluble Lead (Pb) <5 <5 <5 90 Soluble Cadmium (Cd) <5 <5 <5 75 Soluble Antimony (Sb) <5 <5 <5 60 Soluble Selenium (Se) <5 <5 <5 500 Soluble Chromium (Cr) <5 <5 <5 60 Soluble Mercury (Hg) <5 <5 <5 60 Soluble Arsenic (As) <2.5 <2.5 < Result (ppm) (10) (11) (12) (ppm) Soluble Barium (Ba) <5 <5 < Soluble Lead (Pb) <5 <5 <5 90 Soluble Cadmium (Cd) <5 <5 <5 75 Soluble Antimony (Sb) <5 <5 <5 60 Soluble Selenium (Se) <5 <5 <5 500 Soluble Chromium (Cr) <5 <5 <5 60 Soluble Mercury (Hg) <5 <5 <5 60 Soluble Arsenic (As) <2.5 <2.5 < Page 8 of 32

9 Result (ppm) (13) (14) (15) (ppm) Soluble Barium (Ba) <5 <5 < Soluble Lead (Pb) <5 <5 <5 90 Soluble Cadmium (Cd) <5 <5 <5 75 Soluble Antimony (Sb) <5 <5 <5 60 Soluble Selenium (Se) <5 <5 <5 500 Soluble Chromium (Cr) <5 <5 <5 60 Soluble Mercury (Hg) <5 <5 <5 60 Soluble Arsenic (As) <2.5 <2.5 < Result (ppm) (16) (ppm) Soluble Barium (Ba) < Soluble Lead (Pb) <5 90 Soluble Cadmium (Cd) <5 75 Soluble Antimony (Sb) <5 60 Soluble Selenium (Se) <5 500 Soluble Chromium (Cr) <5 60 Soluble Mercury (Hg) <5 60 Soluble Arsenic (As) < ppm = parts per million = : Since the sample weight of the component was less than 10 mg, soluble heavy metal analysis was not applicable. Tested Components: (1) Coatings on plastic label (sticker #2645). Coatings (red, black) on foam (copter #11). Coatings (blue, black) on foam (copter #11). Coatings (green, black) on foam (copter #11). (5) Transparent plastic label excluding coatings (sticker #2645, copter #11). (6) White foam (space shuttle #2650, glider #2645). (7) Paper label with plastic film (sticker #2650). (8) Black plastic (frame of space shuttle #2650). (9) Orange plastic (launcher #2650). (10) Light brown elastic band (launcher #2650). (11) Dull black plastic (propeller #11). (12) Yellow plastic (hook and holder #11). (13) Transparent elastic band (holder #11). (14) Shiny light brown elastic band (loops #11). (15) Brown wood (rod #11). (16) Silver color metal (hook #11). Test Period : Apr 07, 2017 to Apr 18, 2017 Page 9 of 32

10 (7) Total Lead (Pb) Content in Non-Surface Coating Materials (Substrate) Test Method : Standard Operating Procedures for Determining Total Lead (Pb) in Children s Products, test methods CPSC-CH-E and/or CPSC-CH-E , analysed by Inductively Coupled Argon Plasma Spectrometry. Tested Component Result in ppm in ppm (1/2/3) < (4/5/6) < (7/8) < (9/10) < (11) < ppm = parts per million = mg/kg Tested Components: (1) Transparent plastic label excluding coatings (sticker #2645, copter #11). (2) White foam (space shuttle #2650, glider #2645). (3) Paper label with plastic film (sticker #2650). (4) Black plastic (frame of space shuttle #2650). (5) Orange plastic (launcher #2650). (6) Light brown elastic band (launcher #2650). (7) Dull black plastic (propeller #11). (8) Yellow plastic (hook and holder #11). (9) Transparent elastic band (holder #11). (10) Shiny light brown elastic band (loops #11). (11) Silver color metal (hook #11). Test Period : Apr 07, 2017 to Apr 18, 2017 Page 10 of 32

11 (8) Total Lead (Pb) Content in Surface Coating Test Method : Standard Operating Procedure for Determining Lead (Pb) in Paint and Other Similar Surface Coatings, test method CPSC-CH-E , analysed by Inductively Coupled Argon Plasma Spectrometry. Tested Component Result in ppm in ppm (1) <20 90 (2/3) <20 90 (4) <20 90 ppm = parts per million = mg/kg Tested Components: (1) Coatings on plastic label (sticker #2645). (2) Coatings (red, black) on foam (copter #11). (3) Coatings (blue, black) on foam (copter #11). (4) Coatings (green, black) on foam (copter #11). Test Period : Apr 07, 2017 to Apr 18, 2017 Page 11 of 32

12 (9) Phthalate Content Test Test Method : Standard Operating Procedure for Determining Phthalates, test method CPSC-CH-C was used and phthalate content was determined by Gas Chromatographic-Mass Spectrometric (GC-MS) analysis. Six Phthalate content: Compounds (%, w/w) Result (%, w/w) (1) (2/3/4) (5/6/7) Dibutyl phthalate (DBP) < < Diethyl hexyl phthalate (DEHP) <0.01 <0.01 < Benzyl butyl phthalate (BBP) <0.01 <0.01 < Diisononyl phthalate (DINP) <0.01 <0.01 < Di-n-octyl phthalate (DnOP) <0.01 <0.01 < Diisodecyl phthalate (DIDP) <0.01 <0.01 < Compounds Result (%, w/w) (%, (8/9) (10/11) w/w) Dibutyl phthalate (DBP) <0.01 < Diethyl hexyl phthalate (DEHP) <0.01 < Benzyl butyl phthalate (BBP) <0.01 < Diisononyl phthalate (DINP) <0.01 < Di-n-octyl phthalate (DnOP) <0.01 < Diisodecyl phthalate (DIDP) <0.01 < The above limit was quoted according to US Consumer Product Safety Improvement Act 2008 for prohibition on sale of certain products containing specified phthalates. Remark(s) As requested by the applicant, test was conducted only on components listed in this report. Tested Components: (1) Coatings (red, black, blue, green) on foam (copter #11). (2) Transparent plastic label excluding coatings (sticker #2645, copter #11). (3) White foam (space shuttle #2650, glider #2645). (4) Paper label with plastic film (sticker #2650). (5) Black plastic (frame of space shuttle #2650). (6) Orange plastic (launcher #2650). (7) Light brown elastic band (launcher #2650). (8) Dull black plastic (propeller #11). (9) Yellow plastic (hook and holder #11). (10) Transparent elastic band (holder #11). (11) Shiny light brown elastic band (loops #11). and Apr 28, 2017 Test Period : Apr 07, 2017 to May 19, 2017 Page 12 of 32

13 (10) Tracking Label Assessment Test Standard : Consumer Product Safety Improvement Act (CPSIA) 2008 Section 103 tracking labels for children products. Tracking label found on the packaging: Paul K. Guillow, Inc. LOT 316, 416, 214 Tracking label found on the product: Paul K. Guillow, Inc. LOT 416 Note: The tracking label assessment was based on the submitted sample and the information provided by the applicant. There was no verification on the validity of such information. and May 16, 2017 Test Period : Apr 07, 2017 to May 17, 2017 Page 13 of 32

14 (11) Total Lead (Pb) content Test Method : Acid digestion and analysed by Inductively Coupled Argon Plasma Spectrometry. Coating: Tested Component Result in %, w/w in %, w/w (1) < (2/3) < (4) < Substrate: Tested Component Result in %, w/w in %, w/w (5/6/7) < (8/9/10) < (11/12) < (13/14) < (15) < The above limit was quoted from the Consent Judgement no. RG settled by Superior Court of the State of California for the County of Alameda, for toys based on the California Proposition 65. Tested Components: (1) Coatings on plastic label (sticker #2645). (2) Coatings (red, black) on foam (copter #11). (3) Coatings (blue, black) on foam (copter #11). (4) Coatings (green, black) on foam (copter #11). (5) Transparent plastic label excluding coatings (sticker #2645, copter #11). (6) White foam (space shuttle #2650, glider #2645). (7) Paper label with plastic film (sticker #2650). (8) Black plastic (frame of space shuttle #2650). (9) Orange plastic (launcher #2650). (10) Light brown elastic band (launcher #2650). (11) Dull black plastic (propeller #11). (12) Yellow plastic (hook and holder #11). (13) Transparent elastic band (holder #11). (14) Shiny light brown elastic band (loops #11). (15) Silver color metal (hook #11). Test Period : Apr 07, 2017 to Apr 18, 2017 Page 14 of 32

15 (12) Phthalate Content Test Test Method : Solvent extraction and Gas Chromatographic-Mass Spectrometric (GC-MS) analysis. Assessment: The testing scope was not applicable to the submitted sample, therefore no phthalate testing has been performed. Test Period : Apr 07, 2017 to May 19, 2017 Page 15 of 32

16 (13) Toxic Elements Analysis Test Method : Model Toxics in Packaging Legislation requirement of packaging and packaging components, acid digestion method was used and toxic elements contents were determined by Inductively Coupled Argon Plasma Spectrometry, and Hexavalent Chromium content was determined by UV-Visible Spectrophotometry. Result (ppm) (1) (2/3/4) (5) (ppm) Total Lead (Pb) <5 <5 <5 -- Total Cadmium (Cd) <5 <5 <5 -- Total Mercury (Hg) <5 <5 <5 -- Chromium VI (Cr (VI)) <1 <1 <1 -- Sum of Pb, Cd, Hg and Cr (VI) <16 <16 < Result (ppm) (6) (7/8) (9) (ppm) Total Lead (Pb) <5 <5 <5 -- Total Cadmium (Cd) <5 <5 <5 -- Total Mercury (Hg) <5 <5 <5 -- Chromium VI (Cr (VI)) <1 <1 <1 -- Sum of Pb, Cd, Hg and Cr (VI) <16 <16 < ppm = parts per million = mg/kg Tested Components: (1) Coatings on plastic (poly bag #2650, #2645) (packaging). (2) Transparent plastic excluding coatings (poly bag #2650, #2645) (packaging). (3) Paper label with plastic film (background of sticker #2650) (packaging). (4) Transparent plastic label with coatings (sticker #2650) (packaging). (5) White paper sheet (back of sticker #2650, #2645) (packaging). (6) Coatings on plastic (lining of poly bag #11) (packaging). (7) Transparent plastic sheet (poly pag #11) (packaging). (8) White foam (background of copter #11) (packaging). (9) Coatings (blue, black, green, red) on foam (background of copter #11) (packaging). Test Period : Apr 07, 2017 to Apr 18, 2017 Page 16 of 32

17 (14) Physical and Mechanical Tests Test Standard : European Standard on Safety of Toys EN71-1:2014 Applicant's specified age group for testing : For Ages over 8 Years The submitted samples were undergone the following abuse tests: Clause Testing Items Protective components (60N) 8.5 Drop Test ( 850 mm x 5 ) 8.7 Impact test (1 kg) Clause Requirement Assessment 4 General requirements 4.1 Material cleanliness P 4.2 Assembly NA 4.3 Flexible plastic sheeting NA 4.4 Toy bags NA 4.5 Glass NA 4.6 Expanding Materials NA 4.7 Edges P 4.8 Points and Metallic wires P 4.9 Protruding parts NA 4.10 Parts moving against each other P 4.11 Mouth actuated toys and other toys intended to be put into mouth NA 4.12 Balloons NA 4.13 Cords of toy kites and other flying toys NA 4.14 Enclosures NA 4.15 Toys intended to bear the mass of a child NA 4.16 Heavy immobile toys NA 4.17 Projectiles P# Aquatic toys and inflatable toys NA 4.19 Percussion caps specifically designed for use in toys and toys using NA percussion caps 4.20 Acoustics NA 4.21 Toys containing non -electrical heat source NA 4.22 Small balls NA 4.23 Magnets NA 4.24 Yo-yo balls NA 4.25 Toys attached to food NA 5 Toys intended for children under 36 months 5.1 General requirements for toys intended for children under 36 months NA 5.2 Soft-filled toys and soft-filled parts of a toy NA 5.3 Plastic sheeting NA 5.4 Cords, chains and electrical cables in toys NA 5.5 Liquid filled toys NA 5.6 Speed limitation of electrically driven ride-on toys NA 5.7 Glass and porcelain NA 5.8 Shape and size of certain toys NA 5.9 Toys comprising monofilament fibres NA Page 17 of 32

18 Clause Requirement Assessment 5.10 Small balls NA 5.11 Play figures NA 5.12 Hemispheric-shaped toys NA 5.13 Suction cups NA 5.14 Straps intended to be worn fully or partially around the neck NA 6 Packaging #1 7 Warnings, markings and instructions for use 7.1 General P 7.2 Toys not intended for children under 36 months NA 7.3 Latex balloons NA 7.4 Aquatic toys NA 7.5 Functional toys NA 7.6 Hazardous sharp functional edges and points NA 7.7 Projectiles NA 7.8 Imitation protective masks and helmets NA 7.9 Toy kites NA 7.10 Roller skates, inline skates, skateboards and certain other ride-on toys NA 7.11 Toys intended to be attached to or strung across a cradle, cot, or NA perambulator 7.12 Liquid-filled teethers NA 7.13 Percussion caps specifically designed for use in toys NA 7.14 Acoustics NA 7.15 Toy bicycles NA 7.16 Toys intended to bear the mass of a child NA 7.17 Toys comprising monofilament fibres NA 7.18 Toy scooters NA 7.19 Rocking horses and similar toys NA 7.20 Magnetic / electrical experimental sets NA 7.21 Toys with electrical cables exceeding 300 mm in length NA 7.22 Toys with cords or chains intended for children of 18 months and over but under 36 months NA Abbreviation : P = NA = Not Applicable Page 18 of 32

19 Below are additional information according to the Toy Safety Directive 2009/48/EC requirement. These information also appears as a note within the EN71 but are not standard requirements and not accredited: Marking The manufacturer's and importer's name, registered trade name or registered trade mark, the address and type, batch, serial or model number or other element allowing their identification shall be indicated on the product itself. In addition, toys or packagings shall also bear the CE-marking. After checking, it was found that Toy Packaging Manufacturer's name Present for item #11 & #2650 Present Manufacturer's address Present for item #11 & #2650 Present Importer's name Absent Absent Importer's address Absent Absent Product identification code Present for item #11 Present CE-marking Absent Present The submitted projectile sample of SPACE SHUTTLE is propelled into free flight by a child releasing an elastic band and EN71-1 does not cover by the specific risks related to this type of product, therefore, a further safety evaluation of EC Type examination must be conducted in addition to this report. Remark(s): #1 = As requested by applicant, the requirement of clause (c) for Helicopter rotors and single propellers under Projectiles requirement and clause 6 for Packaging was not assessed. and May 16, 2017 Test Period : Apr 07, 2017 to May 17, 2017 (15) Flammability Test Test Standard : European Standard on Safety of Toys EN71-2 : A1 : 2014 Clause Requirement Assessment 4.1 General P 4.2 Toys to be worn on the head NA 4.3 Toy disguise costumes and toys intended to be worn by a child in play NA 4.4 Toys intended to be entered by a child NA 4.5 Soft filled toys NA Abbreviation : P = NA = Not Applicable Test Period : Apr 07, 2017 to Apr 22, 2017 Page 19 of 32

20 (16) 19 Toxic Element Migration Test Test Standard : EN71-3: A1:2014 Category (III): Scraped-off toy material: Result (mg/kg) (1) (2) (3) (mg/kg) Soluble Aluminium (Al) <300 <300 < Soluble Antimony (Sb) <10 <10 < Soluble Arsenic (As) <10 <10 <10 47 Soluble Barium (Ba) 120 <10 < Soluble Boron (B) <50 <50 < Soluble Cadmium (Cd) <5 <5 <5 17 Soluble Chromium (III) (Cr III) ++ <10 <10 < Soluble Chromium (VI) (Cr VI) ++ <0.1 <0.1 < Soluble Cobalt (Co) <10 <10 < Soluble Copper (Cu) <10 <10 < Soluble Lead (Pb) <10 <10 < Soluble Manganese (Mn) <10 <10 < Soluble Mercury (Hg) <10 <10 <10 94 Soluble Nickel (Ni) <10 <10 < Soluble Selenium (Se) <10 <10 < Soluble Strontium (Sr) <100 <100 < Soluble Tin (Sn) <10 <10 < Soluble Organic tin <2.0 < Soluble Zinc (Zn) <100 <100 < Result (mg/kg) (4) (5) (6) (mg/kg) Soluble Aluminium (Al) <300 <300 < Soluble Antimony (Sb) <10 <10 < Soluble Arsenic (As) <10 <10 <10 47 Soluble Barium (Ba) <10 <10 < Soluble Boron (B) <50 <50 < Soluble Cadmium (Cd) <5 <5 <5 17 Soluble Chromium (III) (Cr III) ++ <10 <10 < Soluble Chromium (VI) (Cr VI) ++ <0.1 <0.1 < Soluble Cobalt (Co) <10 <10 < Soluble Copper (Cu) <10 <10 < Soluble Lead (Pb) <10 <10 < Soluble Manganese (Mn) <10 <10 < Soluble Mercury (Hg) <10 <10 <10 94 Soluble Nickel (Ni) <10 <10 < Soluble Selenium (Se) <10 <10 < Soluble Strontium (Sr) <100 <100 < Soluble Tin (Sn) <10 <10 < Soluble Organic tin ++ <2.0 <2.0 < Soluble Zinc (Zn) <100 <100 < Page 20 of 32

21 Result (mg/kg) (7) (8) (9) (mg/kg) Soluble Aluminium (Al) <300 <300 < Soluble Antimony (Sb) <10 <10 < Soluble Arsenic (As) <10 <10 <10 47 Soluble Barium (Ba) <10 <10 < Soluble Boron (B) <50 <50 < Soluble Cadmium (Cd) <5 <5 <5 17 Soluble Chromium (III) (Cr III) ++ <10 <10 < Soluble Chromium (VI) (Cr VI) ++ <0.1 <0.1 < Soluble Cobalt (Co) <10 <10 < Soluble Copper (Cu) <10 <10 < Soluble Lead (Pb) <10 <10 < Soluble Manganese (Mn) <10 <10 < Soluble Mercury (Hg) <10 <10 <10 94 Soluble Nickel (Ni) <10 <10 < Soluble Selenium (Se) <10 <10 < Soluble Strontium (Sr) <100 <100 < Soluble Tin (Sn) <10 <10 < Soluble Organic tin ++ <2.0 <2.0 < Soluble Zinc (Zn) <100 <100 < Result (mg/kg) (10) (11) (12) (mg/kg) Soluble Aluminium (Al) <300 <300 < Soluble Antimony (Sb) <10 <10 < Soluble Arsenic (As) <10 <10 <10 47 Soluble Barium (Ba) <10 <10 < Soluble Boron (B) <50 <50 < Soluble Cadmium (Cd) <5 <5 <5 17 Soluble Chromium (III) (Cr III) ++ <10 <10 < Soluble Chromium (VI) (Cr VI) ++ <0.1 <0.1 < Soluble Cobalt (Co) <10 <10 < Soluble Copper (Cu) <10 <10 < Soluble Lead (Pb) <10 <10 < Soluble Manganese (Mn) <10 < Soluble Mercury (Hg) <10 <10 <10 94 Soluble Nickel (Ni) <10 <10 < Soluble Selenium (Se) <10 <10 < Soluble Strontium (Sr) <100 <100 < Soluble Tin (Sn) <10 <10 < Soluble Organic tin ++ <2.0 <2.0 < Soluble Zinc (Zn) < < Page 21 of 32

22 Result (mg/kg) (13) (14) (15) (mg/kg) Soluble Aluminium (Al) <300 <300 < Soluble Antimony (Sb) <10 <10 < Soluble Arsenic (As) <10 <10 <10 47 Soluble Barium (Ba) < Soluble Boron (B) <50 <50 < Soluble Cadmium (Cd) <5 <5 <5 17 Soluble Chromium (III) (Cr III) ++ <10 <10 < Soluble Chromium (VI) (Cr VI) ++ <0.1 <0.1 < Soluble Cobalt (Co) <10 <10 < Soluble Copper (Cu) <10 <10 < Soluble Lead (Pb) <10 <10 < Soluble Manganese (Mn) 15 <10 < Soluble Mercury (Hg) <10 <10 <10 94 Soluble Nickel (Ni) <10 <10 < Soluble Selenium (Se) <10 <10 < Soluble Strontium (Sr) <100 <100 < Soluble Tin (Sn) <10 <10 < Soluble Organic tin ++ <2.0 <2.0 < Soluble Zinc (Zn) < Result (mg/kg) (16) (mg/kg) Soluble Aluminium (Al) < Soluble Antimony (Sb) < Soluble Arsenic (As) <10 47 Soluble Barium (Ba) Soluble Boron (B) < Soluble Cadmium (Cd) <5 17 Soluble Chromium (III) (Cr III) ++ < Soluble Chromium (VI) (Cr VI) ++ < Soluble Cobalt (Co) < Soluble Copper (Cu) < Soluble Lead (Pb) < Soluble Manganese (Mn) < Soluble Mercury (Hg) <10 94 Soluble Nickel (Ni) < Soluble Selenium (Se) < Soluble Strontium (Sr) < Soluble Tin (Sn) < Soluble Organic tin ++ < Soluble Zinc (Zn) < mg/kg = milligram per kilogram Page 22 of 32

23 ++ : Unless the test results were marked with "^" or " ", Chromium (III) & Chromium (VI) and Organic tin contents were not directly determined and were derived from migration results of total chromium and tin respectively. Organic tin test result was expressed as tributyl tin. : Confirmation test was performed on the tested component. The reported value was the sum of the migration values of Methyl tin, Butyl tin, Dibutyl tin, Tributyl tin, Tetrabutyl tin, n-octyl tin, Din-octyl tin, Di-n-propyl tin, Diphenyl tin and Triphenyl tin after converted to Tributyl tin by calculation. Tested Components: (1) Coatings on plastic label (sticker #2645). (2) Transparent plastic label excluding coatings (sticker #2645, copter #11). (3) White foam (space shuttle #2650, glider #2645). (4) Paper label with plastic film (sticker #2650). (5) Black plastic (frame of space shuttle #2650). (6) Orange plastic (launcher #2650). (7) Light brown elastic band (launcher #2650). (8) Dull black plastic (propeller #11). (9) Yellow plastic (hook and holder #11). (10) Transparent elastic band (holder #11). (11) Shiny light brown elastic band (loops #11). (12) Brown wood (rod #11). (13) Silver color metal (hook #11). (14) White foam with (red, black) printings (copter #11). (15) White foam with (blue, black) printings (copter #11). (16) White foam with (green, black) printings (copter #11). Test Period : Apr 07, 2017 to Apr 18, 2017 Page 23 of 32

24 (17) Polycyclic Aromatic Hydrocarbons (PAH) Content Test Method : Solvent extraction and determined by Gas Chromatographic - Mass Spectrometry (GC/MS). Compound Result (ppm) (1) (2/3/4) (5/6/7) (ppm) Benzo(a)pyrene <0.10 <0.10 < Benzo(e)pyrene <0.10 <0.10 < Benzo(a)anthracene <0.10 <0.10 < Chrysene <0.10 <0.10 < Benzo(b)fluoranthene <0.10 <0.10 < Benzo(j)fluoranthene <0.10 <0.10 < Benzo(k)fluoranthene <0.10 <0.10 < Dibenzo(a,h)anthracene <0.10 <0.10 < Compound Result (ppm) (8/9) (10/11) (ppm) Benzo(a)pyrene <0.10 < Benzo(e)pyrene <0.10 < Benzo(a)anthracene <0.10 < Chrysene <0.10 < Benzo(b)fluoranthene <0.10 < Benzo(j)fluoranthene <0.10 < Benzo(k)fluoranthene <0.10 < Dibenzo(a,h)anthracene <0.10 < The above limit was quoted according to Annex XVII Items 50 of the REACH Regulation (EC) no. 1907/2006 & amendment (EU) no. 1272/2013 for polycyclic aromatic hydrocarbons (PAH). ppm = parts per million = mg/kg Tested Components: (1) Coatings on plastic label (sticker #2645). (2) Transparent plastic label excluding coatings (sticker #2645, copter #11). (3) White foam with (red, black, blue, green) coatings (space shuttle #2650, glider #2645). (4) Paper label with plastic film (sticker #2650). (5) Black plastic (frame of space shuttle #2650). (6) Orange plastic (launcher #2650). (7) Light brown elastic band (launcher #2650). (8) Dull black plastic (propeller #11). (9) Yellow plastic (hook and holder #11). (10) Transparent elastic band (holder #11). (11) Shiny light brown elastic band (loops #11). Test Period : Apr 07, 2017 to Apr 11, 2017 Page 24 of 32

25 (18) Phthalate Content Test Test Method : EN14372, by Gas Chromatographic-Mass Spectrometric (GC-MS) analysis. Six Phthalate content: Compounds (%, w/w) Result (%, w/w) (1) (2/3/4) (5/6/7) Dibutyl phthalate (DBP) < < Diethyl hexyl phthalate (DEHP) <0.01 <0.01 < Benzyl butyl phthalate (BBP) <0.01 <0.01 < Sum of DBP,DEHP & BBP < < Diisononyl phthalate (DINP) <0.01 <0.01 < Di-n-octyl phthalate (DnOP) <0.01 <0.01 < Diisodecyl phthalate (DIDP) <0.01 <0.01 < Sum of DINP,DnOP & DIDP <0.01 <0.01 < Compounds Result (%, w/w) (%, (8/9) (10/11) w/w) Dibutyl phthalate (DBP) <0.01 < Diethyl hexyl phthalate (DEHP) <0.01 < Benzyl butyl phthalate (BBP) <0.01 < Sum of DBP,DEHP & BBP <0.01 < Diisononyl phthalate (DINP) <0.01 < Di-n-octyl phthalate (DnOP) <0.01 < Diisodecyl phthalate (DIDP) <0.01 < Sum of DINP,DnOP & DIDP <0.01 < The above limit was quoted according to Annex XVII Items 51 & 52 of the REACH Regulation (EC) no. 1907/2006 & amendment no. 552/2009 for phthalate content in toys and childcare articles. Remark(s) As requested by the applicant, test was conducted only on components listed in this report. Tested Components: (1) Coatings (red, black, blue, green) on foam (copter #11). (2) Transparent plastic label excluding coatings (sticker #2645, copter #11). (3) White foam (space shuttle #2650, glider #2645). (4) Paper label with plastic film (sticker #2650). (5) Black plastic (frame of space shuttle #2650). (6) Orange plastic (launcher #2650). (7) Light brown elastic band (launcher #2650). (8) Dull black plastic (propeller #11). (9) Yellow plastic (hook and holder #11). (10) Transparent elastic band (holder #11). (11) Shiny light brown elastic band (loops #11). and Apr 28, 2017 Test Period : Apr 07, 2017 to May 19, 2017 Page 25 of 32

26 (19) Dimethylfumarate Content Test Method : By solvent extraction and Gas Chromatographic-Mass Spectrometric (GC-MS) analysis. Tested Component Result (ppm) Requirement (ppm) (1) < Remark : ppm = parts per million = mg/kg Detection = 0.05ppm Tested Component : (1) Brown wood (rod #11). Testing period : Apr 07, 2017 to Apr 18, 2017 (20) Formaldehyde Release Test method: EN717-3 : 1996 by Flask Method. Tested Component Result (ppm) (1) <1 Remark : ppm = parts per million = mg/kg Tested Component : (1) Brown wood (rod #11). Testing period : Apr 07, 2017 to Apr 11, 2017 Page 26 of 32

27 (21) Toxic Elements Analysis Test Method : 94/62/EC and amendment 2013/2/EU & Directive (EU) 2015/720 Directive on packaging and packaging waste, acid digestion method was used and toxic elements contents were determined by Inductively Coupled Argon Plasma Spectrometry, and Hexavalent Chromium content was determined by UV-Visible Spectrophotometry. Result (ppm) (1) (2/3/4) (5) (ppm) Total Lead (Pb) <5 <5 <5 -- Total Cadmium (Cd) <5 <5 <5 -- Total Mercury (Hg) <5 <5 <5 -- Chromium VI (Cr (VI)) <1 <1 <1 -- Sum of Lead, Cadmium, Mercury and Chromium Cr (VI) <16 <16 < Result (ppm) (6) (7/8) (9) (ppm) Total Lead (Pb) <5 <5 <5 -- Total Cadmium (Cd) <5 <5 <5 -- Total Mercury (Hg) <5 <5 <5 -- Chromium VI (Cr (VI)) <1 <1 <1 -- Sum of Lead, Cadmium, Mercury and Chromium Cr (VI) <16 <16 < ppm = parts per million = mg/kg Tested Components: (1) Coatings on plastic (poly bag #2650, #2645) (packaging). (2) Transparent plastic excluding coatings (poly bag #2650, #2645) (packaging). (3) Paper label with plastic film (background of sticker #2650) (packaging). (4) Transparent plastic label with coatings (sticker #2650) (packaging). (5) White paper sheet (back of sticker #2650, #2645) (packaging). (6) Coatings on plastic (lining of poly bag #11) (packaging). (7) Transparent plastic sheet (poly pag #11) (packaging). (8) White foam (background of copter #11) (packaging). (9) Coatings (blue, black, green, red) on foam (background of copter #11) (packaging). Test Period : Apr 07, 2017 to Apr 18, 2017 Page 27 of 32

28 (22) Short Chain Chlorinated Paraffin (C10 - C13) (SCCP) Content Test method: Solvent extraction and followed by Gas Chromatographic - Negative Chemical Ionization - Mass Spectrometry (GC-NCI-MS) Analysis. Tested Component Result in (%, w/w) (1/2/3) <0.01 (4/5/6) <0.01 (7/8) <0.01 (9/10) <0.01 Requirement : 0.15 % (w/w) Remark : Detection limit = 0.01% (w/w) Tested Component : (1) Transparent plastic label with coatings (sticker #2645, copter #11). (2) White foam with (red, black, blue, green) coatings (space shuttle #2650, glider #2645). (3) Paper label with plastic film (sticker #2650). (4) Black plastic (frame of space shuttle #2650). (5) Orange plastic (launcher #2650). (6) Light brown elastic band (launcher #2650). (7) Dull black plastic (propeller #11). (8) Yellow plastic (hook and holder #11). (9) Transparent elastic band (holder #11). (10) Shiny light brown elastic band (loops #11). Testing period : Apr 07, 2017 to Apr 18, 2017 Page 28 of 32

29 (23) Cadmium (Cd) Content Test Method : Acid digestion method was used and total Cadmium content was determined by Inductively Coupled Argon Plasma Spectrometry. Tested Component Result in %, w/w in %, w/w (1) ND 0.1 (2/3) ND 0.1 (4) ND 0.1 (5/6/7) ND 0.01 (8/9/10) ND 0.01 (11/12) ND 0.01 (13/14) ND 0.01 ND : Not detected (< %) Tested Components: (1) Coatings on plastic label (sticker #2645). (2) Coatings (red, black) on foam (copter #11). (3) Coatings (blue, black) on foam (copter #11). (4) Coatings (green, black) on foam (copter #11). (5) Transparent plastic label excluding coatings (sticker #2645, copter #11). (6) White foam (space shuttle #2650, glider #2645). (7) Paper label with plastic film (sticker #2650). (8) Black plastic (frame of space shuttle #2650). (9) Orange plastic (launcher #2650). (10) Light brown elastic band (launcher #2650). (11) Dull black plastic (propeller #11). (12) Yellow plastic (hook and holder #11). (13) Transparent elastic band (holder #11). (14) Shiny light brown elastic band (loops #11). Test Period : Apr 07, 2017 to Apr 18, 2017 Page 29 of 32

30 (24) Organotin Content Test Method : By solvent extraction, followed by Gas Chromatography Mass Spectrometric (GC/MS) analysis. Compounds Result (%, w/w) of tin Requirement (%, w/w) of tin (1/2/3) (4/5/6) Tri-substituted organotin^ <0.005 < Dibutyltin (DBT) <0.005 < Dioctyltin (DOT) <0.005 < Compounds Result (%, w/w) of tin Requirement (%, w/w) of tin (7/8) (9/10) Tri-substituted organotin^ <0.005 < Dibutyltin (DBT) <0.005 < Dioctyltin (DOT) <0.005 < Remark : The above limit was quoted according to Annex XVII Items 20 of the REACH Regulation (EC) no. 1907/2006 & amendment (EU) No. 276/2010 (formerly known as Decision 2009/425/EC) for organotin content. Remark : Detection limit = 0.005% (w/w) of tin ^ = The reported value was calculated by summation of the values of Tri-butyltin, Triphenyltin, Tri-methyltin, Tri-octyltin, Tri-cyclohexyltin Tested Components : (1) Transparent plastic label with coatings (sticker #2645, copter #11). (2) White foam with (red, black, blue, green) coatings (space shuttle #2650, glider #2645). (3) Paper label with plastic film (sticker #2650). (4) Black plastic (frame of space shuttle #2650). (5) Orange plastic (launcher #2650). (6) Light brown elastic band (launcher #2650). (7) Dull black plastic (propeller #11). (8) Yellow plastic (hook and holder #11). (9) Transparent elastic band (holder #11). (10) Shiny light brown elastic band (loops #11). Testing period : Apr 07, 2017 to Apr 18, 2017 Page 30 of 32

31 (25) Tetrabromodiphenyl Ether (TetraBDE), Pentabromodiphenyl Ether (PentaBDE), Hexabromodiphenyl Ether (HexaBDE) and Heptabromodiphenyl Ether Content Test method: By solvent extraction, followed by Gas Chromatography Mass Spectrometric (GC/MS) Analysis. Compound Result (%, w/w) Requirement (%, w/w) (1) Tetrabromodiphenyl ether (Tetra BDE) < Pentabromodiphenyl ether (Penta BDE) < Hexabromodiphenyl ether (Hexa BDE) < Heptabromodiphenyl ether (Hepta BDE) < Remark : Detection limit = % (w/w) The above limit was quoted according to Regulation (EC) No. 850/2004 & amendment No.757/2010 on persistent organic pollutants (POPs), Annex I, Part A. Tested Component : (1) White foam with (red, black, blue, green) coatings (space shuttle #2650, glider #2645). Testing period : Apr 07, 2017 to Apr 18, 2017 (26) Hexabromocyclododecane (HBCDD) Content Test method: By solvent extraction, followed by and Gas Chromatography Mass Spectrometric (GC/MS) analysis. Tested Component Result (ppm) (1) <10 Requirement : 100 ppm Remark : ppm = parts per million = mg/kg The above limit was quoted according to Regulation (EC) No. 850/2004 & amendment No.(EU) 2016/293 on persistent organic pollutants (POPs), Annex I, Part A Tested Component : (1) White foam with (red, black, blue, green) coatings (space shuttle #2650, glider #2645). Testing period : Apr 07, 2017 to Apr 18, 2017 Page 31 of 32

32 (27) Octabromodiphenyl ether (OctaBDE) Content Test method: By solvent extraction, followed by Gas Chromatography Mass Spectrometric (GC/MS) Analysis. Tested Component Result (%, w/w) Requirement (%, w/w) (1) < (2) < (3) < (4) < (5) < (6) < (7) < (8) < (9) < (10) < Remark : Detection limit = % (w/w) The above limit was quoted according to REACH Regulation (EC) No. 1907/2006, Annex VII, Item 45 & amendment No. 552/2009. Tested Components : (1) Transparent plastic label with coatings (sticker #2645, copter #11). (2) White foam with (red, black, blue, green) coatings (space shuttle #2650, glider #2645). (3) Paper label with plastic film (sticker #2650). (4) Black plastic (frame of space shuttle #2650). (5) Orange plastic (launcher #2650). (6) Light brown elastic band (launcher #2650). (7) Dull black plastic (propeller #11). (8) Yellow plastic (hook and holder #11). (9) Transparent elastic band (holder #11). (10) Shiny light brown elastic band (loops #11). Testing period : Apr 07, 2017 to Apr 18, 2017 ********************************************************************************************************************************* End of report Except where explicitly agreed in writing, all work and services performed by Intertek is subject to our standard Terms and Conditions which can be obtained at our website: Intertek's responsibility and liability are limited to the terms and conditions of the agreement. This report is made solely on the basis of your instructions and / or information and materials supplied by you and provide no warranty on the tested sample(s) be truly representative of the sample source. The report is not intended to be a recommendation for any particular course of action, you are responsible for acting as you see fit on the basis of the report results. Intertek is under no obligation to refer to or report upon any facts or circumstances which are outside the specific instructions received and accepts no responsibility to any parties whatsoever, following the issue of the report, for any matters arising outside the agreed scope of the works. This report does not discharge or release you from your legal obligations and duties to any other person. You are the only one authorized to permit copying or distribution of this report (and then only in its entirety). Any such third parties to whom this report may be circulated rely on the content of the report solely at their own risk. This report shall not be reproduced, except in full. Page 32 of 32