ABTRONIC X1 Fitness Belt USER MANUAL USER MANUAL

Transcription

1 PAGE 1 USER MANUAL

2 PAGE 2 Congratulations on your choice of AbTronicX1 Fitness Belt. Please read this quick guide and the full manual before first use. CONTROLS OFF/Low Button, decrease Intensity ON/Hi Button, increase Intensity LED Light 1 LED Light 2 PROGRAM Button to change 6 programs Battery Compartment, slide down (uses 1 x CR 2032 battery) A self timer switches the unit off after 10 minutes.

3 PAGE 3 1. ON/HI: Turns the unit on and increases the output intensity. The higher the intensity, the larger the contraction. To adjust to maximum output you need to push this button 10 times. 2. OFF/LOW: Each pressing of this button decreases the intensity by one step down to 10 levels. Turns the unit off. 3. PROGRAM: This button is used to select one of the 6 preprogrammed exercise. The setting is indicated by the color and location of the two LED lights on the unit. The AbTronic X1 unit has the following 6 programs: Program LED 1 LED 2 Description 1 YELLOW Off 2 Off YELLOW 3 YELLOW YELLOW Fast Blaster, very fast, 5 pulses / second Fast exercise, 1 pulse / second, also tapping massage General exercise,3 sec. on 2 sec.rest time,deeper massage 4 GREEN Off Full exercise routine with slow and fast elements 5 Off GREEN Pro exercise routine, mixed mode but many fast elements 6 GREEN GREEN Constant on, low frequency

4 PAGE 4 OPERATION 1. Open the battery door by sliding it gently downward. 2. Insert the 1 pc CR 2032 Lithium Battery into the battery compartment. The positive + pole of the battery should be facing you. You can read the + symbol on the battery. Close the battery door.

5 PAGE 5 3. Attach the AbTronic X1 unit onto the Neoprene Center 4. Attach the Velcro flexible belt male part (the rougher Velcro material that is only once on the flexible belt) to the Neoprene center piece Velcro female part (the softer Velcro material on the Neoprene centre piece). This is on the left side of the neoprene center piece when you look onto it.. If the belt is not long enough, you can use the second shorter belt as an extension.

6 PAGE 6 5. Turn the Neoprene belt on its face and place a generous dab of the conductive training gel onto the 2 conductive areas. Spread it evenly and make sure the surface is covered under a film of gel the use of the belt might feel uncomfortable otherwise. Hint: Read the ingredient list on the toning gel that you are using. You should find Water or Aqua on it. DO NOT USE gel or creams that contain oils. The gel MUST be water based. If you have any doubt, use Aloe Vera Gel that can be easily obtained in any Drug Store. 6. Make sure the unit is switched off = no LED light is lighted up. If you have switched on the unit accidentally, than switch it off by pushing the OFF/LOW so that the LED light goes off. 7. Place the AbTronic X1 belt around your stomach or any other area you want to exercise and close the belt to a comfortable fit with the Velcro belt (not too tight). 8. Select Mode by pressing the PROGRAM button repeatedly. Every time you press the PROGRAM button a different LED or combination will light up indicating one of the 6 preprogrammed routines.

7 PAGE 7 9. Push the ON/HI button several times to carefully increase the intensity.adjust the intensity according to your comfort level. You should feel a light tingling. Push HI button 10 x to increase intensity 10 steps 0 <> 1 <> 2 <> 3 <> 4 <> 5 <> 6 <> 7 <> 8 <> 9 <> 10 Push LOW button 10 x to decrease intensity 10 steps ON HI OFF LOW 10. The intensity has 10 steps. With every push of the button ON/HI you increase the intensity by one step, with every push of the button OFF/LOW you decrease the intensity by one step. To switch the unit off, press the OFF/LOW button several times, until the LED lights go off. The unit has an auto-timer. For your convenience it will shut off after 10 minutes of operation. However please use the system for 4 to 12 consecutive cycles/day for best results.

8 PAGE 8 AUTO FUNCTIONS When the conductive area of the belt (silver colored area) does not touch the skin, the intensity can only be set up to 1. If the belt is removed during use, the intensity is automatically reset to 1. If the belt is not placed back into contact with the skin, the unit will turn off after 20 seconds. The unit has an auto-timer. It will shut off after 10 minutes of exercise. If you change the exercise mode within the 10 minutes, the timer will count-down from the original leftover time. WHAT TO DO IF YOU DO NOT FEEL THE STIMULATION Should no stimulation or contraction be felt, move the belt slowly around the area where you want to work on. Make sure you have enough Toning Gel placed on the inside of the neoprene belt. Gradually increase the PULSE INTENSITY by pushing the ON/HI button several times. The AbTronic X1 is a great way to exercise your muscles. It may take a few moments of practice for locating the belt correctly and applying the ideal pressure that provides the best results for you. Hint: If you don t put gel on the belt or the belt is not placed tightly against the skin then an uncomfortable tingling sensation will occur

9 PAGE 9 IMPORTANT NOTES If no or not enough conductive Toning Gel is applied to the neoprene belt, or the belt is not placed tightly against the skin, an uncomfortable tingling sensation could occur. This could also happen if the body has built up excessive oils on the skin. Before each use please ensure that the contact points are thoroughly covered with gel. The neoprene belt should be cleaned regularly with warm water to avoid the build up of body oils. A discoloration of the conductive area however is normal. Do not wash the belt in the washing machine or apply fabric conditioner. If there is a Iocalized redness or irritation on removal of the belt from your skin, this could be caused by the belt drying out during a session. Ensure that it is kept moist at all times. A worn belt can reduce the performance of the unit or cause the belt to feel erratic. The neoprene belt is a consumable item and can wear after 3 months. Wear and tear is not covered by the guarantee. It should be noted however that this design of a belt lasts much longer than comparable stick on gel pads used in other units. For safety, and to avoid unnecessary discomfort, please ensure that the intensity settings are set to zero before and after using the machine. Hint: VERY IMPORTANT: You MUST apply a conductive medium to the silver contact area inside the Neoprene Belt. The Belt must make contact with your skin. It will not work through clothing.

10 PAGE 10 BELT PLACEMENT: Belt Placement The conductive areas can be placed in many different positions, thus allowing more specific targeting of muscle groups. There is a velcro belt that can be used to effectively target individual muscle groups. Please use the long or short Velcro belt to achieve the optimal results. The diagrams in this booklet are provided as a starting recommendation only. AbTronicX1is a personalised training tool and can be adapted to suit the individual. Its intended use is for general physical conditioning. The diagrams shown, have just a letter shown for belt placement. If the contractions are not effective, then place the belt over the area closest. We do not recommend placing the belt over the heart. However as no effective muscle grouping is in this area, there is no need.

11 PAGE 11 BACK FRONT B C B A A I I J J L L P J J I I A A P G D H E N M N M K F F Q Q O O F F * E has been intentionally amitted from this diagram.

12 PAGE 12 ABTRONICX1 FITNESS BELT EXERCISES POINTS A. NECK AND SHOULDERS Gives relaxation and soothing massage to neck and shoulder area B. CHEST Targets breasts in women Targets pectorals in men C. UPPER ABS Targets upper abs similar to situps D. MAIN ABS Targets abs similar to crunch E. LOWER ABS Targets lower abs F. LOVE HANDLES/WAIST Targets love handles.

13 PAGE 13 G. UPPER/MIDDLE BACK Targets upper/middle back. H. LOWER BACK Targets lower back I. ARMS Targets the upper arm. Targets Biceps and Triceps. J. LOWER ARMS Targets lower arms and gripping power. K. BUTTOCKS Targets buttocks, very important posture muscles L. UPPER THIGHS Targets outer/upper thigh muscles. Targets similar muscles to cycling

14 PAGE 14 M. UPPER BACK THIGH Targets tigh muscles N. UPPER FRONT THIGH Targets tigh muscles and similar muscles to cycling O. KNEE AND FRONT THIGH Targets knee/main muscles P. UPPER BACK THIGH Targets the upper back tigh and the biceps femoris. Q. CALVES Targets similar muscles to cycling. Targets calf/foot arch muscles

15 PAGE TAKING CARE OF YOUR UNIT The ABTRONICX1 belt is made of quality materials. The only maintenance required with the ABTRONICX1 is to clean the conductive ara gently from time to time with a wet cloth, soapy water and to replace the battery.do NOT immerse the belt in water or other liquids.do not rub hard on the conductive areas. Do not wash the belt in the washing machine or apply fabric conditioner. NEVER BEND the conductive pads! A discoloration of the conductive area and a crumbled look after many uses however is normal. The conductive pads are a consumable item and can wear with use, depending on the gel you are using, your own body fluids and how often you use the belt. Worn conductive areas can reduce the performance of the unit or cause the belt to feel erratic. Wear and tear is not covered by the guarantee.it should be noted however that this is the most advanced 4 th generation design of a belt that lasts much longer than comparable stick on gel pads used in other units. If several people want to share the ABTRONICX1 you can easily detach the computer unit by unsnapping it from the neoprene center and use it on your own personal belt for hygienic reasons. Just pull the unit off and put it on a new belt. The ABTRONICX1 is extremely energy efficient. The Batteries lasts for approx. 100 sessions of ten minutes. If the output becomes weak or the unit switches off automatically in less than 10 minutes, it is time to change the batteries (even if the LED is still lit up). The electronic computer unit is built very reliable and uses SMT technology. It is maintenance free and will give you many, many years of trouble free usage.

16 PAGE CARE AND CLEANING Do not wash the belt in washing machine or apply fabric softener as this can damage the belt Do not dry clean Do not use bleach Clean accessories with a slightly wet sponge with detergent and wipe with a cloth. Clean the unit with a cloth soaked with disinfectant diluted in water at 1/10th. Clean the training pads with a mix of water/hypoallergenic detergent, then rinse thoroughly. 4.2 IMPORTANT PLEASE READ If no or not enough ABTRONICX1 toning gel is applied to the conductive areas, or the belt is not placed tightly against the skin, an uncomfortable tingling sensation can occur. This can also happen if the body has built up excessive oil on the skin. Before use, ensure that the contact points are thoroughly covered with gel. Please note that some discoloration of the conductive area and a crumbled look is perfectly normal. The unit remains functional even if, after heavy use, the conductive pads develop some cracks, as long as you use enough conductive gel. DO NOT Bend the conductive areas. If you experience skin redness or irritation after removing the belt from your skin, this could be caused by the conductive pads drying out during a session. Ensure that the pads are kept moist

17 PAGE 17 at all times and that you use plenty of the ABTRONICX1 training gel. Worn conductive areas can reduce the performance of the unit or cause the belt to feel erratic. The conductive areas are a consumable item and do wear out eventually. Wear and tear is not covered by the guarantee. 4.3 FREQUENTLY ASKED QUESTIONS Q. How does the ABTRONICX1 really work? A. ABTRONICX1 is designed to copy the messages sent from your brain to the abdominal muscle during exercise. This message causes the muscle to contract and relax. Q. Can muscles become over-developed or strained? A. No - the principle is the same for general training of muscles- the more exercise, with suitable periods of rest, the stronger the muscles become. Q. Can this machine be used for all ages? A. Yes - absolutely. ABTRONICX1 is not age dependent and can be used at any age. However, the very elderly and children should use it under supervision and, keep the intensity low. Q. Will I find it uncomfortable? A. As long as the belt is moist and kept firmly against the skin you will not feel any unpleasantness. At low

18 PAGE 18 intensity you will feel a slight tingling sensation but as the intensity gets higher you will only feel the pleasant contraction. Start using it on your upper Abs first, not directly over the belly button where most people are most sensitive. Q. Should the intensity settings be the same for each muscle? A. Each muscle will respond differently, so intensities will accordingly be different. Move the belt around to find the right trigger point that gives you maximum contraction. Q. Are there any contra-indications to use of the machine? A. Yes - If exercise is inadvisable due to ill health, then a medical practitioner should be consulted before using this or any other device. Read all contra-indications on the last page carefully! Q. When should I notice any effect? A. Depending on the frequency of use and body fat, you should notice increases in abdominal strength within 1-2 weeks. Abdominal muscle tone will show within approximately 3 weeks after incorporating the ABTRONICX1 into your program. Q. I am getting a prickling sensation but no contraction. A. Move the belt slightly to find the right trigger points that give maximum contractions and the most pleasant feeling. Try increasing the intensity. This could also be caused because either the belt does not have enough toning gel on it (water based) or is not tightly placed

19 PAGE 19 against the skin. Failing this remove belt and wash inner surface with wet cloth and soapy water to remove body oils. Q. I noticed a redness of the skin after the exercise. Is this a problem? A. A slight redness of the skin after a session with the ABTRONICX1 is normal. It should fade quickly. Some pressure to the skin from the stretched belt may also cause it. You should not be concerned about this. If the redness is excessive, you may not have used enough conductive toning gel or it may have dried out during a longer session. Try using more toning gel the next time, replenish it after each 10 minute session and use a lower intensity level. 5.0 CONTRAINDICATIONS ABTRONICX1 should NOT be used by people with cardiac pacemaker, defibrillator or other implanted electronic or metallic devices. ABTRONICX1 should NOT be used by pregnant women, and during first 6 weeks after their babies birth. ABTRONICX1 should NOT be used by people with undiagnosed pain syndromes and hemorrhagic diseases. ABTRONICX1 should NOT be used on injured or otherwise impaired muscles ABTRONICX1 should NOT be used on the heart area.

20 PAGE WARNINGS 1. The long-term of chronic electrical stimulation are unknown. 2. Apply electrodes ONLY to normal, intact, clean skin. 3. DO NOT APPLY STIMULATION: Over the carotid sinus nerves. Over the neck or mouth. Severe spasms of the laryngeal and pharyngeal muscles may occur with contractions strong enough to clse the airway and/or cause difficulty in breathing. Stimulation over the neck can also have an adverse effect on the heart rhythm or blood pressure. Transcerebrally (through the head) Over swollen, infected or inflamed areas of skin eruptions (e.g., phlebitis, thrombophlebitis, varicose veins, etc.) Transthoracically; introduction of electrical current into the heart may cause rhythm disturbances, which could be fatal. Over or in proximity to, cancerous lesions. If you are epileptic After experiencing acute trauma or fracture Following recent surgery If you have a hernia (abdominal or lingual) To the frontal, laryngeal and temporal regions of the neck. 4. Never use the ABTRONICX1 while driving, operating machinery or during activities in which involuntary muscle contractions may endanger the user or others. 5. Do not use the ABTRONICX1 in the bath or shower 6. Persons with suspected heart problems or epilepsy should obtain appropriate medical advise. 7. The ABTRONICX1 should never be used while sleeping 8. Do not immerse the ABTRONICX1 unit or belt in any liquid. 9. The ABTRONICX1 must be kept out of reach of children.

21 PAGE PRECAUTIONS: DO NOT USE WHEN: 1. DO NOT use if there is tendency to Hemorrhage (acute trauma or fracture). 2. DO NOT use following any recent surgical procedure when muscle contraction may disrupt the healing process. 3. DO NOT use over the menstruating uterus. 4. DO NOT use if you have skin areas that lack normal sensation 5. Place electrodes in accordance with illustrations PRECAUTIONS: 1. The safety of neuromuscular stimulation during pregnancy has not been established. 2. Place electrodesin accordance with illustrations in the User Manual. 3. Users should start all sessions in a sitting or prone position (minimum for the first 5 minutes) 4. This unit should not be used while driving, operating machinery or during any activity in which involuntary muscle contractions may place the user at undue risk of injury. ADVERSE EFFECTS Skin irritation and burns beneath the electrodes has been reported with the use of electrical muscle stimulation.

22 PAGE POPULATION The ABTRONICX1 is not suitable to use for infants or toddlers, it is suitable to use at any other age, however, the very elderly and children should use it under supervision and, keep the intensity low 5.4 IMPORTANT GUIDELINES The ABTRONICX1 is extremely safe and simple to use, however, ABTRONICX1 does not take any responsibility for any harm caused due to misuse of the product. As a safeguard we suggest you read the entire manual and that if you have the following conditions, please seek professional medical advice before using the machine: After childbirth (see heading After Childbirth) Persons using a heart pacemaker or with cardiac condition Epilepsy Multiple Sclerosis Phlebitis in its active phase (inflammation of a vein) Where tissue is inflamed through disease or injury Recent scar tissue or surgery Varicose veins in its later stages During the heavy days of your period do not use the unit on your abs.

23 PAGE 23 If in doubt, consult your physiotherapist, osteopath, or medical practitioner. The ABTRONICX1 is intended to use on healthy muscles only. Unsupervised children should not use this machine You can easily detach the unit from the belt if you want to clean the belt. To re-attach the unit just snap it on. For easy operation when the unit is used in the abdominal area the display can be flipped upside down with a push of the button.

24 PAGE TROUBLE SHOOTING GUIDE PROBLEM POSSIBLE CAUSE SOLUTION LEDs do Batteries not Install Batteries not light installed up at all Batteries installed Check polarity + sign incorrectly Batteries are Replace Batteries empty LEDs light up, but warning beep is emitted (high pitch warning tone beeps) LEDs light up, but nothing occurs No skin contact Unit not snapped on belt correctly Microprocessor hang up Battery is low Intensity set to low level Not enough conductive gel on belt used gel is not water-based the belt is positioned Incorrectly Belt is worn or has oil deposits. Battery is low Use water based gel on conductive pads and place belt directly onto skin. Check that unit is connected firmly with all connectors to the belt. Increase intensity by pushing the up Perform a RESET, remove Batteries for 1 minute for full RESET Change Battery Increase intensity by pushing the up buttons Put more water based gel between belt and skin Read label on the gel that you use. Make sure you find water or aqua on it. Move belt around to locate your trigger points. Clean conductive area or replace. (see hint below) Change Battery

25 PAGE 25 LEDs light up, but all buttons do not work Microprocessor hang up Battery is low Perform a RESET, remove batteries for 1 minute for full RESET Change Battery Tip: You can determine whether your conductive pads are worn out and need replacing or whether the electronic unit does not generate sufficient output power. Simply unsnap the unit from the belt. Place a little bit of conductive gel on the tip of the fingers of one hand and press your fingers against the contacts of the unit. Switch the unit on and carefully increase intensity to level one or two. If the unit is working properly you will feel a tingling sensation in your fingers which indicates that you need to get new conductive pads. IMPORTANT: POWER RESET If the unit does not switch on, or if you can t change to different programs, the microprocessor may have hanged. Please perform a simple RESET. Remove batteries and replace them after one minute.

26 PAGE 26 SPECIFICATION Channel: Intensity Control: Wave Form Out Voltage Power Supply Size Weight Frequency Pulse Width Contraction Time Relaxation Time Ramp Time Timer Max. Charge per pulse Battery Life Environment for operating and storage: Single Channel Adjustable 0-28uA, Max output 28uA peak to peak into 10k ohm load each channel. Asymmetrical Bi-Phase Square Pulse Adjustable 0-168V, Max output 168V peak to peakinto 10k ohm load each channel. 3V CR2032 battery 55mm(L) X 50mm (W) X 13.8mm (H) 21.2g(with battery) Adjustable, due to different modes. Adjustable, due to different modes. Adjustable, due to different modes. Adjustable, due to different modes. Adjustable, due to different modes. Default time is 10 minutes, Adjustable, due to different modes. Approximately 20 hours at nominal settings Temperature: 10 C ~40 C (50 ~140 F), Humidity rate: 85%, Pressure: Normal atmospheric pressure.

27 PAGE 27 MODES Modes No. 1 Grade Stages(Cycle Repeat A ) A Stage A Stage Frequency (HZ) Pulse Width (ms) Modes No. 2 3 Grade Stages(Cycle Repeat A ) A Stage A Stage A Stage A Stage Frequency (HZ) Pulse Width (ms) Contraction Time (ms) Relaxation Time (ms) Modes No. 4 Grade 1-7 Stages (Cycle from A to N) A Stage B Stage C Stage D Stage E Stage F Stage G Stage Frequency (HZ) Pulse Width (ms) Contraction Time (ms) Relaxation Time (ms)

28 PAGE 28 Modes No. 4 Grade 1-7 Stages (Cycle from A to N) H Stage I Stage J Stage K Stage L Stage M Stage N Stage Frequency (HZ) Pulse Width (ms) Contraction Time (ms) Relaxation Time (ms) Modes No. 4 Grade 8-10 Stages (Cycle from A to N) A Stage B Stage C Stage D Stage E Stage F Stage G Stage Frequency (HZ) Pulse Width (ms) Contraction Time (ms) Relaxation Time (ms) Modes No. 4 Grade 8-10 Stages (Cycle from A to N) H Stage I Stage J Stage K Stage L Stage M Stage N Stage Frequency (HZ) Pulse Width (ms) Contraction Time (ms) Relaxation Time (ms)

29 PAGE 29 Modes No. 5 Grade 1-7 Stages A Stage B Stage C Stage D Stage E Stage F Stage (Cycle from A to F) Frequency (HZ) Pulse Width (ms) Contraction Time (ms) Relaxation Time (ms) Modes No. 5 Grade 8-10 Stages A Stage B Stage C Stage D Stage E Stage F Stage (Cycle from A to F) Frequency (HZ) Pulse Width (ms) Contraction Time (ms) Relaxation Time (ms) Modes No. 6 Grade Stages(Cycle Repeat A Stage A Stage A ) Frequency (HZ) Pulse Width (ms)

30 by Red Lemon Incorporation MMXV RLX1EngV1.3