PEEK SS Columns & Guard Columns

Transcription

1 PEEK SS Columns & Guard Columns ~ Stainless Steel Analytical Columns ~ PEEK Columns ID 2.1, 4.0, 4.6 & 7.5 mm ~ Jour-Guard Cartridges Stainless Steel or PEEK ~ Stainless Steel End Fittings 1/4 OD Columns ~ Stainless Steel Preparative Columns ~ In-Line Biocompatible Guard Columns ~ One-Piece Column Coupler ~ Column End Plugs Stainless Steel Analytical Columns Jour s 4.6 mm ID stainless steel analytical columns are made of high quality SS316L. The finish of the inner surface is extremely smooth with a maximum of 0.2 µm RA. We prefer for safety reasons (especially when packing columns) the threaded (5/16-24) tubing type with SS end-fitting and SS insert. The insert is on the inside conical shaped in order to provide an equal sample distribution over the 0.5 or 2 µm frit. Frits are made of SS 316L and supplied with a PEEK ring. All connections are female fittings. We also offer 3.0 and 4.0 mm ID columns. Stainless Steel Analytical Columns 4.6 mm ID Length 0.5 µm 2.0 µm 50 mm mm mm mm mm Stainless Steel Analytical Columns 4.0 mm ID

2 Length 0.5 µm 2.0 µm 50 mm mm mm mm mm Length 0.5 µm 2.0 µm 50 mm mm mm mm mm Insert End Fitting Packing Adapter Slurry Reservoir Packing Seal P PEEK Encased SS Frit, 2µm P PEEK Encased SS Frit, 0.5 µm

3 PEEK Columns PEEK Columns 4.6 mm & 4.0 mm ID Today s HPLC and IC applications are more demanding than ever. The limitations of traditional stainless steel pose significant problems for a growing number of important biotechnology and ion chromatography applications. Wetted Surfaces: PEEK and PAT (PEEK Alloyed with Teflon) frits Pressures: Max. 350 bar (5000 psi) continous. During packing Max. 560 bar (8000 psi) PEEK Columns 7.5 mm ID Ideal for Semi-prep Biochromatography. The basic column design is shown in the figure and consists of a length of threaded PEEK tubing and two Peek end fittings with the packed bed held in place by two PAT (PEEK Alloyed with Teflon) frits. Connections are made through PEEK inlet and outlet fittings which accept 1/16 OD tubing and standard fingertight fittings. Max operating pressure 350 bar (5000 psi). Low Protein Binding insures high recovery and accurate quantification Wetted Surfaces: PEEK and PAT (PEEK Alloyed with Teflon) frits Pressure: Up to 350 bar (5000 psi) PEEK Columns 2.1 mm ID We have designed this column for your narrow-bore applications and where only limited amounts of sample are available for analysis. Because 2.1 mm ID columns operate at 1/5th the flow rate of their 4.6 mm counterparts, the same sample mass injected on a 2.1 mm column will produce 5X the detector signal. This greater mass sensitivity provides the same analysis as a 4.6 mm column with only 20% of the sample. Only PEEK and PAT (PEEK Alloyed with Teflon) contact the fluid stream. Wetted Surfaces: PEEK and PAT frits Pressure: Should not be used over 210 bar (3000 psi) 2.1 mm ID PEEK Column Tube PAT Frit PEEK End Fitting PEEK Columns 2.1 mm ID mm x 2.1 mm mm x 2.1 mm mm x 2.1 mm mm x 2.1 mm mm x 2.1 mm mm x 2.1 mm PAT Frit End Fitting

4 65216 Packing Adapter Packing Seal PEEK End Fitting PAT Frit 4.6 mm ID PEEK Column Tube PEEK Columns 4.6 mm ID mm x 4.6 mm mm x 4.6 mm mm x 4.6 mm mm x 4.6 mm mm x 4.6 mm mm x 4.6 mm mm x 4.6 mm PAT Frit PEEK End Fitting Packing Adapter Packing Seal 7.5 mm ID PEEK Column Tube PEEK Frit Spacer PAT Frit PEEK End Fitting PEEK Columns 7.5 mm ID mm x 7.5 mm mm x 7.5 mm mm x 7.5 mm mm x 7.5 mm mm x 7.5 mm

5 mm x 7.5 mm PAT Frit PEEK End Fitting PEEK Frit Spacer Packing Adapter Packing Seal PEEK End Fitting PAT Frit 4.0 mm ID PEEK Column Tube mm x 7.5 mm mm x 7.5 mm mm x 7.5 mm mm x 7.5 mm mm x 7.5 mm mm x 7.5 mm PAT Frit PEEK End Fitting Packing Adapter Packing Seal Jour-Guard Cartridges Stainless Steel or PEEK

6 Jour-Guard Cartridge System is a breakthrough in simplicity, reliability and performance! Packing SS Jour-Guard Cartridge RP/C18-5 µm SS Jour-Guard Cartridge RP/C8-5 µm SS Jour-Guard Cartridge RP/Phenyl-5 µm SS Jour-Guard Cartridge NP/Silica-5 µm PEEK Jour-Guard Cartridge RP/C18-5 µm PEEK Jour-Guard Cartridge RP/C8-5 µm PEEK Jour-Guard Cartridge RP/Phenyl-5 µm PEEK Jour-Guard Cartridge NP/Silica-5 µm Jour-Guard Holder Includes: P/N 25602, Jour One-Piece Column Coupler, Female Type

7 Stainless Steel End Fittings 1/4 OD Columns - Can be delivered with or without distributor plate - Comes complete with 0.5, 2 or 5 µm SS frits - Ready for mounting with a configuration to match most instruments. We produce high quality SS column end fittings for standard 1/4 columns from SS 316L steel. Here is a fitting which is passivated with nitric acid and which features a flow geometry producing optimum distribution of sample and eluant across the surface of the column. The Jour SS end fittings are cleaned with ultrasound and are ready for mounting. Stainless Steel End Fittings 1/4 OD Columns CE CE14-2 CE14-5 Stainless Steel Column End Fitting with 0.5 µm SS Frit Stainless Steel Column End Fitting with 2 µm SS Frit Stainless Steel Column End Fitting with 5 µm SS Frit Back to Peek - SS Columns & Guard Columns Stainless Steel Preparative Columns Jour offers a complete line of empty 20 mm ID (1 OD) preparative columns in a variety of lengths including guard columns. We use a zero void end-cap, which accepts industry standard (10-32) fittings and all columns have threaded ends. This avoids the complicated connections with ferrules and allows easy cleaning and refilling. Jour Stainless Steel 20 mm ID Prep. Columns Length (mm)

8 Untitled Document Page 8 of SS Prep. Column 20 mm ID 50 mm SS Prep. Column 20 mm ID 100 mm SS Prep. Column 20 mm ID 150 mm SS Prep. Column 20 mm ID 250 mm SS Prep. Column 20 mm ID 300 mm SS Prep. Column 20 mm ID 500 mm SS Prep. Column 20 mm ID 1000 mm Accessories for 20 mm ID Prep. Columns 43 Slurry reservoir complete for 20 mm ID (1 OD) columns (light version, 1 m length, 20 mm ID) 44 Slurry reservoir complete for 20 mm ID (1 OD) columns (heavy version, 40 mm ID) 46 SS Replacement Frit 5 µm 47 SS Column to Column Adapter 20 mm (to join two columns or guard columns) 48 SS Guard Column (50 mm) 49 SS End piece 54 SS Plate Teflon encased Poro-Web Frit OD 20 mm Thickness 1.7 mm 2 µm Teflon encased Poro-Web Frit OD 20 mm Thickness 1.7 mm 5 µm Back to Peek - SS Columns & Guard Columns In-Line Biocompatible Guard Column - Biocompatible - Easy to Fill Jour's In-Line PEEK Guard Column System extends the life of your valuable analytical column by trapping contaminants from the sample and mobile phase, thereby preventing loss of retention.

9 Only PEEK and PAT contact the eluant and sample. This system is ideal for use with proteins or other biopolymers that may be contaminated or adsorbed by metal surfaces. Jour Guard Columns are easily dry-packed or slurry packed. Guard columns may be changed in minutes without the use of tools - all connections may be made by hand. In-Line PEEK Guard Column In-Line Guard Column, Includes Long Cartridge Nut Guard Cartridge Insert Guard Cartridge ID 8.00 x 3.00 mm Filter Body Slurry Packing Adapter Back to Peek - SS Columns & Guard Columns One-Piece Column Coupler - Join Column to Column - Join Column to Guard Column - Join Column to Injector or Detector - No Wrenches Required Seals to 350 bar (5000 psi) - Metal-Free PEEK Version Here is a inexpensive way to connect columns without the use of extra tubing to join a column to a guard column or to join a column to the injector. The One-Piece-Column-Coupler is made of PEEK with a knurled handle which replaces wrenches. It is also metal-free, and can sustain a working pressure of 350 bar (5000 psi). One-Piece Column Coupler Color Code Female Type Column Coupler for Columns with Black female ports Waters Type Column Coupler for Waters Columns Red Male Type Column Coupler for Columns with Red + Bushing Male Fittings, Valco Type Column Coupler for Valco Fittings Blue Waters Type Column Coupler to Female ports Black with W & F intials

10 Back to Peek - SS Columns & Guard Columns Column End Plugs Try our column end plugs in fingertight design. One size fits all columns. Easy handling is guaranteed by the additional 5/16" wrench flat, which allows you to loosen the plug in case it should be stuck. The long design and the threading down to the ferrule ensures a safe closing of your valuable column. We have made the entire test: Plug sealing, plug evaporation and of course the drop test. We recommend our Column End Plug. Column End Plugs P/N Color 4071 White 4072 Black 4073 Red 4074 Green 4075 Blue Back to Peek - SS Columns & Guard Columns