Model PA10 ELECTRIC AIR CONDITIONER SS-PA10-09 FEATURES

Transcription

1 AVAILABLE SIZES: CERTIFICATION: Nominal sizes available from 018 through 060 to meet the needs of residential and light commercial applications. All models are listed with UL, (U.S. and Canada), ARI, and CEC. ELECTRICAL RANGE: Units are offered in v, single phase 018 through 060 sizes; 208/230v, three phase in 036, 048 and 060 sizes; and 460v, three phase in 060 size. FAN MOTOR: CABINET: The totally enclosed fan motor provides greater reliability under adverse conditions and dependable performance for many years. The permanent split capacitor type motor was designed for optimum efficiency. The motor was then qualified under extreme conditions to help ensure a long, reliable life. A weather protective cabinet of steel is protected with a galvanized coating and treated with a layer of zinc phosphate. A coat of modified polyester powder coating is then applied and baked on, providing each unit with a hard, smooth finish that will last for many years. All screws on cabinet exterior are coated for a long-lasting, rustresistant, quality appearance. FEATURES UNIT DESIGN: COMPRESSOR: SERVICE VALVES: SERVICEABILITY: The copper tube, enhanced sine wave, aluminum fin coil is designed for optimum heat transfer. Vertical air discharge carries sound and hot condenser air up and away from adjacent patio areas and foliage. The base pan is designed for easy removal of water, dirt, and leaves. Each compressor is protected with internal temperature- and current-sensitive overloads. An internal pressure relief valve provides high-pressure protection to the refrigerant system. For improved serviceability, all models are equipped with a compressor terminal plug. Both service valves are brass, front seating type with sweat connections. Valves are externally located so refrigerant tube connections can be made quickly and easily. Each valve has a service port for ease of checking operating refrigerant pressures. One panel provides access to electrical controls. Removal of top gives access to fan motor, compressor, and condenser coil. Model PA10 ELECTRIC CONDITIONER SS-PA10-09

2 NOTES: 1. Allow 30 in. clearance to service side of unit, 48 in. above unit, 6 in. on one side, 12 in. on remaining side, and 24 in. between units for proper airflow. 2. Minimum outdoor operating ambient in cooling mode is 55 F max 125 F. 3. Series designation is the 14th position of the unit model number. 4. Center of gravity. A 3/ 8 IN. DIA TIEDOWN KNOCKOUTS (2) PLACES IN IN DISCHARGE IN DISCHARGE DISCHARGE FIELD POWER SUPPLY CONN 7 / 8 IN. DIA HOLE WITH 1 1 / 8 IN. DIA KNOCKOUT AND 1 3 / 8 IN. DIA KNOCKOUT FIELD CONTROL SUPPLY CONN 7 / 8 IN. DIA HOLE B J N P 3 / 8 IN. DIA LIQUID LINE CONN DISCHARGE IN 2 7 / 8 C E M F D DIA VAPOR LINE CONN 1 1 / 4 A937 DIMENSIONS (IN.) UNIT SIZE SERIES A B C D E F J M N P NOTE: The data in this publication is displayed for all series, however, every series may not be available from manufacturer. SHIPPING WEIGHT (Lb) 018 C 22-1/ /16 3-3/16 5/8 18-1/2 4-1/16 8-3/ /8 12-1/4 9-3/ C 22-1/ /16 3-3/16 5/8 18-1/2 4-1/16 8-3/ /8 12-1/4 10-3/ C 22-1/ /16 3-3/16 3/4 18-1/2 4-1/16 8-3/ /8 12-1/4 11-1/ B 22-1/ /16 3-3/16 3/4 18-1/2 4-1/16 8-3/ /8 12-1/4 11-3/ C 22-1/ /16 3-3/16 3/4 18-1/2 4-1/16 8-3/ /8 12-1/4 11-3/ C, D 22-1/ /16 3-1/4 7/8 18-1/2 4-1/16 8-3/ /8 12-1/4 11-3/ C 22-1/ /16 3-1/4 7/8 18-1/2 4-1/16 8-3/ /8 12-1/ C 22-1/ /16 3-1/4 7/8 18-1/2 4-1/16 8-3/ /8 12-1/ D 22-1/ /16 3-1/4 7/8 18-1/2 4-1/16 8-3/ /8 12-1/4 15-1/ C /16 3-1/4 7/8 23-1/2 6-1/ / UNITARY CONDITIONING MANUFACTURER CERTIFIED TO ARI AS COMPLYING WITH ARI EQUIPMENT STANDARD 210 REGISTERED QUALITY SYSTEM SOUND POWER (A-wtd., non-pure tone corrected.) NOTE: Tested in accordance with ARI standard (Not listed with ARI.) 2 CERTIFICATION APPLIES ONLY WHEN THE COMPLETE SYSTEM IS LISTED WITH ARI. UNIT SOUND OCTAVE BAND CENTER FREQUENCY (Hz) SIZE LEVEL C C C B C C D C C D C

3 See notes on page 5. METERING DEVICE PISTON* UNIT SIZE-SERIES IDENTIFICATION NO. 018-C C C B C C D C C, D C 93 * Piston listed is for any approved coil non-capillary tube combination. Piston is shipped with outdoor unit and must be installed in an approved indoor coil. SPECIFICATIONS UNIT SIZE SERIES C C C ELECTRICAL Unit Volts Hertz Phase Operating Voltage Range* Compressor Rated Load Amps Locked Rotor Amps Condenser Fan Motor Full Load Amps Min Unit Ampacity for Wire Sizing Min Wire Size (60 C/75 F Copper) AWG 14/14 14/14 14/14 Max Wire Length (60 C/75 F) (Ft) 66/ 53/50 39/37 Max Branch Circuit Fuse Size** COMPRESSOR & REFRIGERANT Compressor Type Reciprocating Temperature and Current Protection Internal Line Break Refrigerant Type and Amount (Lbs) R R R Refrigerant Tubes (In. OD) Vapor and Liquid (Up to 50 Ft) 5/8 and 3/8 3/4 and 3/8 CONDENSER COIL & FAN Coil Face Area (Sq Ft) Fan Motor HP, Type, and RPM 1/12 PSC and /10 PSC and 1125 Volts Hertz Phase 208/ Condenser Airflow (CFM) OPTIONAL EQUIPMENT Cycle Protector KSACY0101AAA Start Assist PTC Type KAACS0201PTC Start Assist Capacitor/Relay Type KSAHS0901AAA Low-Pressure Switch KAALP0101LPS High-Pressure Switch KSAHI0101HPS Time-Delay Relay KAATD0101TDR Winter Start Control KAAWS0101AAA Evaporator Freeze Thermostat KAAFT0101AAA Crankcase Heater KAACH1001AAA Liquid Line Solenoid Valve KAALS0101LLS Filter Drier P S Coastal Filter KAACF0401MED TXV Kit (RPB) KAATX0201RPB KAATX0301RPB KAATX0401RPB TXV (Hard Shutoff) KSATX0601HSO Thermostat, Manual Changeover, Non-Programmable, F/ C, 1-Stage Heat, 1-Stage Cool TSTATPPBAC01-B Thermostat, Manual Changeover, 5-2-Day Programmable, F/ C, 1-Stage Heat, 1-Stage Cool TSTATPPSAC01-B Backplate for Standard Thermostat TSTATXXBBP01 Backplate for Programmable Thermostat TSTATXXPBP01 Outdoor Air Temperature Sensor TSTATXXSEN01-B MotorMaster Control 32LT Ball Bearing Fan Motor HC34GE232 3

4 SPECIFICATIONS Continued UNIT SIZE SERIES C B C/D C ELECTRICAL Unit Volts Hertz Phase / Operating Voltage Range* Compressor Rated Load Amps / Locked Rotor Amps / Condenser Fan Motor Full Load Amps 1.4 Min Unit Ampacity for Wire Sizing / Min Wire Size (60 C/75 F Copper) AWG 12/12 14/14 10/10 Max Wire Length (60 C/75 F) (Ft) 57/54 65/ 67/63 Max Branch Circuit Fuse Size** COMPRESSOR & REFRIGERANT Compressor Type Reciprocating Scroll/Recip Scroll Temperature and Current Protection Internal Line Break Refrigerant Type and Amount (Lbs) R R R R Refrigerant Tubes (In. OD) Vapor and Liquid (Up to 50 Ft) 3/4 and 3/8 7/8 and 3/8 CONDENSER COIL & FAN Coil Face Area (Sq Ft) Fan Motor HP, Type, and RPM 1/4 PSC and 1125 Volts Hertz Phase 208/ Condenser Airflow (CFM) 2500 OPTIONAL EQUIPMENT Cycle Protector KSACY0101AAA Start Assist PTC Type KAACS0201PTC Start Assist Capacitor/Relay Type KSAHS1901AAA N/A KSAHS1501AAA/ KSAHS2201AAA KSAHS1601AAA Low-Pressure Switch KAALP0101LPS High-Pressure Switch KSAHI0101HPS Time-Delay Relay KAATD0101TDR Winter Start Control KAAWS0101AAA Evaporator Freeze Thermostat KAAFT0101AAA Crankcase Heater KAACH1001AAA KAACH1201AAA/ KAACH1001AAA KAACH1201AAA Liquid Line Solenoid Valve KAALS0101LLS Filter Drier P S P S Coastal Filter KAACF0401MED TXV Kit (RPB) KAATX0501RPB KAATX0601RPB TXV (Hard Shutoff) KSATX0601 HSO KSATX0701HSO Thermostat, Manual Changeover, Non-Programmable, F/ C, 1-Stage Heat, 1-Stage Cool TSTATPPBAC01-B Thermostat, Manual Changeover, 5-2-Day Programmable, F/ C, 1-Stage Heat, 1-Stage Cool TSTATPPSAC01-B Backplate for Standard Thermostat TSTATXXBBP01 Backplate for Programmable Thermostat TSTATXXPBP01 Outdoor Air Temperature Sensor TSTATXXSEN01-B MotorMaster Control 32LT Ball Bearing Fan Motor HC40GE232 See notes on page 5. 4

5 SPECIFICATIONS Continued UNIT SIZE SERIES C/D C/D C C C ELECTRICAL Unit Volts Hertz Phase / / Operating Voltage Range* Compressor Rated Load Amps 24.4/ / Locked Rotor Amps 140.0/ / Condenser Fan Motor Full Load Amps Min Unit Ampacity for Wire Sizing 31.9/ / Min Wire Size (60 C/75 F Copper) AWG 8/10 14/14 8/8 12/12 14/14 Max Wire Length (60 C/75 F) (Ft) 97/59 48/46 82/78 58/55 152/144 Max Branch Circuit Fuse Size** COMPRESSOR & REFRIGERANT Compressor Type Scroll Temperature and Current Protection Internal Line Break Refrigerant Type and Amount (Lbs) R /6.10 R Refrigerant Tubes (In. OD) Vapor and Liquid (Up to 50 Ft) 7/8 and 3/8 1-1/8 and 3/8 CONDENSER COIL & FAN Coil Face Area (Sq Ft) 9.45/ Fan Motor HP, Type, and RPM 1/4 PSC and 1125 Volts Hertz Phase Condenser Airflow (CFM) OPTIONAL EQUIPMENT Cycle Protector KSACY0101AAA Start Assist PTC KAACS0201PTC N/A KAACS0201PTC N/A Start Assist Capacitor/RelayType KSAHS1601AAA/ KSAHS1501AAA N/A KSAHS1601AAA N/A Low-Pressure Switch KAALP0101LPS High-Pressure Switch KSAHI0101HPS Time-Delay Relay KAATD0101TDR Winter Start Control KAAWS0101AAA Evaporator Freeze Thermostat KAAFT0101AAA Crankcase Heater KAACH1201AAA KAACH1301AAA Liquid Line Solenoid Valve KAALS0101LLS Filter Drier P S Coastal Filter KAACF0401MED KAACF0501LRG TXV Kit (RPB) KAATX0601RPB KAATX0701RPB TXV Hard Shutoff KSATX0701HSO Thermostat, Manual Changeover, Non-Programmable, F/ C, 1 Stage Heat, 1 Stage Cool TSTATPPBAC01-B Thermostat, Manual Changeover, 5-2-Day Programmable, F/ C, 1-Stage Heat, 1-Stage Cool TSTATPPSAC01-B Backplate for Standard Thermostat TSTATXXBBP01 Backplate for Programmable Thermostat TSTATXXPBP01 Outdoor Air Temperature Sensor TSTATXXSEN01-B MotorMaster Control 32LT LT Ball Bearing Fan Motor HC40GE232 HC40GE4 * Permissible limits of the voltage range at which unit will operate satisfactorily. Operation outside these limits may result in unit failure. If wire is applied at ambient greater than 30 C (86 F), consult Table of the NEC (ANSI/NFPA 70). The ampacity of nonmetallic-sheathed cable (NM), trade name ROMEX, shall be that of 60 C (140 F) conductors, per the NEC (ANSI/NFPA 70) Article Length shown is as measured 1 way along wire path between unit and service panel for voltage drop not to exceed 2%. ** Time-delay fuse or circuit breaker. Start assist capacitor and relay required when using liquid solenoid valve or hard shutoff TXV (except 048 and 060 Sizes). Do not use hard shutoff TXV with liquid solenoid valve. Furnace model numbers P08UA, P08LA, and PG8HA are not compatible with this thermostat. N/A Not applicable in this application. NOTES: 1. Control circuit is 24v on all units and requires external power source. 2. All motors/compressors contain internal overload protection. 3. Copper wire must be used from service disconnect to unit. 5

6 ACCESSORY USAGE GUIDELINE ACCESSORY REQUIRED FOR LOW-AMBIENT APPLICATIONS (Below 55 F) REQUIRED FOR LONG-LINE APPLICATIONS* (Over 50 Ft) REQUIRED FOR SEA COAST APPLICATIONS (Within 2 Miles) Crankcase Heater Yes Yes No Evaporator Freeze Thermostat Yes No No Winter Start Control Yes No No Accumulator No No No Compressor Start Assist Capacitor and Relay Yes Yes No MotorMaster Control Yes No No Wind Baffle See low-ambient instructions No No Coastal Filter No No Yes Support Feet Recommended No Recommended Liquid-Line Solenoid Valve or Hard Shutoff TXV No See Long-Line Application Guideline Ball Bearing Fan Motor Yes No No * For tubing line sets between 50 and 175 ft and/or 20 ft vertical differential, refer to Residential s Split s Long-Line Application Guidelines. Only when low-pressure switch is used. No ACCESSORY DESCRIPTION AND USAGE (Listed Alphabetically) 1. Ball Bearing Fan Motor A fan motor with ball bearings which permits speed reduction while maintaining bearing lubrication. SUGGESTED USE: Required on all units where Low-Ambient kit (full modulation feature) or MotorMaster Control has been added. 2. Coastal Filter A mesh screen inserted under the top cover and inside the base pan to protect the condenser coil from salt damage without restricting airflow. SUGGESTED USE: In geographic areas where salt damage could occur. 3. Compressor Start Assist Capacitor/Relay Type Start capacitor and start relay gives hard boost to compressor motor at each start-up. SUGGESTED USE: Installations where interconnecting tube length exceeds 50 ft. Installations where outdoor design temperature exceeds 105 F (40.6 C). Replacement installations with hard shutoff expansion valve on indoor coil. 4. Compressor Start Assist PTC Type Solid-state electrical device which gives a soft boost to the compressor at each start-up. SUGGESTED USE: Installations with marginal power supply. Replacement installations with rapid pressure balance (RPB) expansion valve on indoor coil. 5. Crankcase Heater An electric resistance heater which mounts to the base of the compressor to keep the lubricant warm during off cycles. Improves compressor lubrication on restart and minimizes chance of refrigerant slugging. May or may not include a thermostat control. SUGGESTED USE: When interconnecting tube length exceeds 50 ft. When unit will be operated below 55 F (12.8 C) outdoor air temperature. Use with low-ambient controller. All commercial installations. 6. Cycle Protector Solid-state timing device which prevents compressor rapid recycling. Control provides an approximate 5-minute delay after power to the compressor has been interrupted for any reason, including normal room thermostat cycling. SUGGESTED USE: Installations in areas where power interruptions are frequent. Where user is likely to play with the room thermostat. All commercial installations. Installations where interconnecting tube length exceeds 50 ft. High-rise applications. 7. Evaporator Freeze Thermostat An SPST temperature actuated switch which stops unit operation when evaporator reaches freeze-up conditions. SUGGESTED USE: All units where winter start control has been added. 8. High-Pressure Switch Auto reset SPST switch activated by refrigerant pressure on high side of refrigerant circuit. Cycles compressor off if refrigerant pressure rises to about 400 psig. Provides additional protection against compressor damage due to loss of outdoor airflow. To prevent rapid compressor recycling, cycle protector can be used with this switch. SUGGESTED USE: Installations exposed to very dirty outdoor air. Installations where condenser inlet air temperature exceeds 125 F (51.7 C). 9. Liquid Solenoid Valve (LSV) An electrically operated shutoff valve to be installed at the outdoor or indoor unit (depending on tubing configuration) and which stops and starts refrigerant liquid flow in response to compressor operation. Maintains a column of refrigerant liquid ready for action at next compressor operation cycle. Note: Compressor start assist capacitor/relay type must also be used. SUGGESTED USE: For improved system performance in air conditioners for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory. In certain long line applications. (Refer to Long-Line Application Guideline.) 6

7 ACCESSORY DESCRIPTION AND USAGE (Listed Alphabetically) Continued 10. Low-Pressure Switch Auto reset SPST switch activated by refrigerant pressure on low side of refrigerant circuit. Cycles compressor off if refrigerant pressure drops to about 27 psig. Prevents indoor coil freeze-up due to loss of indoor airflow. Also, provides additional protection against compressor damage due to loss of refrigerant charge. To prevent rapid compressor recycling. Cycle protector can be used with this switch. SUGGESTED USE: Where indoor coil is exposed to dirty air. All commercial installations. 11. MotorMaster Control A fan speed control device activated by a temperature sensor. Designed to control condenser fan motor speed in response to the saturated, condensing temperature during operation in cooling mode only. For outdoor temperatures down to 20 F, it maintains condensing temperature at 100 F ± 10 F. SUGGESTED USE: operation at outdoor temperatures below 55 F. All commercial installations. 12. Sound Hood Wraparound sound attenuation cover for the compressor. Reduces unit sound level by about 2dBA. SUGGESTED USE: Unit installed closer than 15 ft to quiet areas bedrooms, etc. Unit installed between 2 houses less than 10 ft apart. 13. Thermostatic Expansion Valve (TXV) Kits A modulating flow control valve which meters refrigerant liquid flow rate into the evaporator in response to the superheat of the refrigerant gas leaving the evaporator. Kit includes valve, adapter tubes, and external equalizer tube. Both hard shutoff and RPB type valves are available. SUGGESTED USE: For improved system performance in cooling mode for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory. 14. Time-Delay Relay An SPST delay relay which briefly continues operation of the indoor blower motor to provide additional cooling after the compressor cycles off. SUGGESTED USE: For improved efficiency ratings for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory. 15. Winter Start Control An SPST delay relay which bypasses the low-pressure switch for approximately 3 minutes to permit start-up for cooling operation under low-load conditions. SUGGESTED USE: All air conditioners where low-ambient controller has been added. 7

8 RATINGS AND PERFORMANCE UNIT SIZE-SERIES 018-C 024-C 030-C 036-B (3 Phase) 036-C (1 Phase) See notes on page 10. INDOOR MODEL TOT. CAP. BTUH FACTORY SUPPLIED ENHANCE- MENT STANDARD RATING SEER PAYNE GAS FURNACE OR ACCESSORY TDR ACCESSORY TXV *CC5A/CD5AA018 17,200 NONE CC5A/CD5AA024 17,400 NONE CC5A/CD5AW024 17,400 NONE CE3AA024 17,400 NONE CF5AA024 17,400 NONE CK3BA024 17,400 NONE CK5A/CK5BA018 17,200 NONE CK5A/CK5BA024 17,400 NONE CK5A/CK5BW024 17,400 NONE FF1DNA018 17,200 TDR FF1DNA024 17,400 TDR FF1DNE018 17,200 TDR&TXV FF1DNE024 17,400 TDR&TXV PF1MNA018 17,200 TDR PF1MNA024 17,400 TDR PF1MNB018 17,200 TDR PF1MNB024 17,400 TDR *CC5A/CD5AA024 22,000 NONE CC5A/CD5AA030 22,400 NONE CC5A/CD5AW024 22,000 NONE CC5A/CD5AW030 22,400 NONE CE3AA024 22,000 NONE CE3AA030 22,400 NONE CF5AA024 22,000 NONE CK3BA024 22,000 NONE CK3BA030 22,400 NONE CK5A/CK5BA024 22,000 NONE CK5A/CK5BA030 22,400 NONE CK5A/CK5BW024 22,000 NONE CK5A/CK5BW030 22,400 NONE FF1DNA024 22,200 TDR FF1DNA030 22,800 TDR FF1DNE024 22,200 TDR&TXV FF1DNE030 22,800 TDR&TXV PF1MNA024 22,200 TDR PF1MNA030 22,400 TDR PF1MNB024 22,200 TDR PF1MNB030 22,400 TDR *CC5A/CD5AA030 27,600 NONE CC5A/CD5AA036 28,400 NONE CC5A/CD5AW030 27,600 NONE CC5A/CD5AW036 28,400 NONE CE3AA030 27,600 NONE CE3AA036 28,400 NONE CF5AA036 28,400 NONE CK3BA030 27,600 NONE CK3BA036 28,400 NONE CK5A/CK5BA030 27,600 NONE CK5A/CK5BA036 28,400 NONE CK5A/CK5BT036 28,400 NONE CK5A/CK5BW030 27,600 NONE CK5A/CK5BW036 28,400 NONE FF1DNA030 27,600 TDR FF1DNE030 27,600 TDR&TXV PF1MNA030 27,600 TDR PF1MNA036 28,400 TDR PF1MNB030 27,600 TDR PF1MNB036 28,400 TDR *CC5A/CD5AA036 33,800 NONE CC5A/CD5AA042 33,800 NONE CC5A/CD5AW036 33,800 NONE CE3AA036 33,400 NONE CE3AA042 33,600 NONE CF5AA036 33,600 NONE CK3BA036 33,800 NONE CK3BA042 33,800 NONE CK5A/CK5BA036 33,800 NONE CK5A/CK5BA042 33,800 NONE CK5A/CK5BT036 33,800 NONE CK5A/CK5BT042 33,800 NONE CK5A/CK5BW036 33,800 NONE *CC5A/CD5AA036 33,800 NONE CC5A/CD5AA042 33,800 NONE CC5A/CD5AW036 33,800 NONE CC5A/CD5AW042 33,800 NONE CE3AA036 33,400 NONE CE3AA042 33,600 NONE CF5AA036 33,600 NONE CK3BA036 33,800 NONE CK3BA042 33,800 NONE CK5A/CK5BA036 33,800 NONE CK5A/CK5BA042 33,800 NONE CK5A/CK5BT036 33,800 NONE CK5A/CK5BT042 33,800 NONE CK5A/CK5BW036 33,800 NONE EER 8

9 RATINGS AND PERFORMANCE Continued UNIT SIZE-SERIES 036-C (1 Phase) 042-C, D 047-C 048-C, D (1 & 3 Phase) 060-C (1 & 3 Phase) See notes on page 10. INDOOR MODEL TOT. CAP. BTUH FACTORY SUPPLIED ENHANCE- MENT STANDARD RATING SEER PAYNE GAS FURNACE OR ACCESSORY TDR ACCESSORY TXV PF1MNA036 33,200 TDR PF1MNA042 33,800 TDR PF1MNA071 35,000 TDR&TXV PF1MNB036 33,200 TDR PF1MNB042 33,800 TDR PF1MNB071 35,000 TDR&TXV *CC5A/CD5AA042 40,000 NONE CC5A/CD5AC048 39,500 NONE CC5A/CD5AW042 40,000 NONE CC5A/CD5AW048 40,500 NONE CD5AA048 40,500 NONE CE3AA042 40,000 NONE CE3AA048 40,500 NONE CF5AA048 40,500 NONE CK3BA042 40,000 NONE CK3BA048 40,500 NONE CK5A/CK5BA042 40,000 NONE CK5A/CK5BA048 40,500 NONE CK5A/CK5BE042 40,500 NONE CK5A/CK5BT042 40,000 NONE CK5A/CK5BT048 40,500 NONE CK5A/CK5BW048 40,500 NONE PF1MNB042 40,000 TDR PF1MNB048 41,000 TDR PF1MNB071 42,000 TDR&TXV *CD5AA048 44,000 NONE CC5A/CD5AA060 44,000 NONE CC5A/CD5AC048 43,000 NONE CC5A/CD5AW048 44,000 NONE CC5A/CD5AW060 44,500 NONE CE3AA048 44,000 NONE CE3AA060 44,500 NONE CF5AA048 44,000 NONE CK3BA048 44,000 NONE CK3BA060 44,000 NONE CK5A/CK5BA048 44,000 NONE CK5A/CK5BA060 44,000 NONE CK5A/CK5BT048 44,000 NONE CK5A/CK5BT060 44,000 NONE CK5A/CK5BW048 44,000 NONE CK5A/CK5BX060 44,500 NONE PF1MNA048 44,500 TDR PF1MNA060 45,000 TDR PF1MNA070 45,500 TDR PF1MNA071 45,000 TDR&TXV PF1MNB048 44,500 TDR PF1MNB060 45,000 TDR PF1MNB070 45,500 TDR PF1MNB071 45,000 TDR&TXV *CD5AA048 45,500 NONE CC5A/CD5AA060 45,500 NONE CC5A/CD5AC048 44,500 NONE CC5A/CD5AW048 45,500 NONE CC5A/CD5AW060 46,000 NONE CE3AA048 45,500 NONE CE3AA060 46,000 NONE CF5AA048 45,500 NONE CK3BA048 45,500 NONE CK3BA060 45,500 NONE CK5A/CK5BA048 45,500 NONE CK5A/CK5BA060 45,500 NONE CK5A/CK5BT048 45,500 NONE CK5A/CK5BT060 45,500 NONE CK5A/CK5BW048 45,500 NONE CK5A/CK5BX060 46,000 NONE PF1MNB048 45,500 TDR PF1MNB060 46,000 TDR PF1MNB070 46,500 TDR PF1MNB071 46,500 TDR&TXV *CC5A/CD5AW060 57,000 NONE CC5A/CD5AA060 56,000 NONE CE3AA060 57,000 NONE CK3BA060 56,000 NONE CK5A/CK5BA060 56,000 NONE CK5A/CK5BT060 56,000 NONE CK5A/CK5BX060 57,000 NONE PF1MNA060 57,500 TDR PF1MNA070 58,000 TDR PF1MNA071 58,000 TDR&TXV PF1MNB060 57,500 TDR PF1MNB070 58,000 TDR PF1MNB071 58,000 TDR&TXV EER 9

10 * Tested Combination In most cases, only 1 method should be used to achieve TDR function. Using more than 1 method in a system may cause degradation in performance. Use either the accessory Time-Delay Relay KAATD0101TDR or a furnace equipped with TDR. Most Payne furnaces are equipped with TDR. Requires hard shutoff TXV; based on computer simulation. EER Energy Efficiency Ratio SEER Seasonal Energy Efficiency Ratio TDR Time-Delay Relay TXV Thermostatic Expansion Valve N/A Not Applicable NOTES: 1. Ratings are net values reflecting the effects of circulating fan motor heat. Supplemental electric heat is not included. 2. Tested outdoor/indoor combinations have been tested in accordance with DOE test procedures for central air conditioners. Ratings for other combinations are determined under DOE computer simulation procedures. 3. Determine actual CFM values obtainable for your system by referring to fan performance data in fan-coil or furnace-coil literature. 4. Minimum outdoor operating ambient in cooling mode is 55 F (12.8 C), maximum 115 F (46.1 C). 5. The dashes ( ) appearing in the SEER WITH ACCESSORY TDR column indicate no improvement in efficiency due to time-delay function built into unit as manufactured (see table). 10

11 EVAPORATOR CFM EWB DETAILED COOLING CAPACITIES* CONDENSER ENTERING TEMPERATURES F Sens kw** Sens kw** Sens kw** Sens kw** Sens PA10JA018-C Outdoor Section With CC5A/CD5AA018 Section kw** Multipliers for Determining the Performance With Other Sections Section Size Power Section Size Power CC5A/CD5AA FF1DNA CC5A/CD5AW FF1DNE CE3AA CF5AA PF1MNA CK3BA CK5A/CK5BA PF1MNB CK5A/CK5BW PA10JA024-C Outdoor Section With CC5A/CD5AA024 Section Multipliers for Determining the Performance With Other Sections Section Size Power Section Size Power CC5A/CD5AA CK5A/CK5BW CC5A/CD5AW FF1DNA CE3AA FF1DNE CF5AA PF1MNA CK3BA PF1MNB CK5A/CK5BA See notes on page

12 EVAPORATOR CFM EWB DETAILED COOLING CAPACITIES* Continued CONDENSER ENTERING TEMPERATURES F Sens kw** Sens kw** Sens kw** Sens kw** Sens PA10JA030-C Outdoor Section With CC5A/CD5AA030 Section kw** Multipliers for Determining the Performance With Other Sections Section Size Power Section Size Power CC5A/CD5AA CK5A/CK5BT CK5A/CK5BW CC5A/CD5AW FF1DNA CE3AA FF1DNE PF1MNA CF5AA CK3BA PF1MNB CK5A/CK5BA PA10JA036-B Outdoor Section With CC5A/CD5AA036 Section Multipliers for Determining the Performance With Other Sections Section Size Power Section Size Power CC5A/CD5AA CK3BA CC5A/CD5AW CK5A/CK5BA CE3AA CK5A/CK5BT CF5AA CK5A/CK5BW See notes on page

13 EVAPORATOR CFM EWB DETAILED COOLING CAPACITIES* Continued CONDENSER ENTERING TEMPERATURES F Sens kw** Sens kw** Sens kw** Sens kw** Sens PA10JA036-C Outdoor Section With CC5A/CD5AA036 Section kw** Multipliers for Determining the Performance With Other Sections Section Size Power Section Size Power CC5A/CD5AA CK5A/CK5BT CC5A/CD5AW CK5A/CK5BW PF1MNA CE3AA CF5AA PF1MNB CK3BA CK5A/CK5BA PA10JA042-C, D Outdoor Section With CC5A/CD5AA042 Section Multipliers for Determining the Performance With Other Sections Section Size Power Section Size Power CC5A/CD5AA CK5A/CK5BA CC5A/CD5AC CC5A/CD5AW CK5A/CK5BE CK5A/CK5BT CD5AA CE3AA CK5A/CK5BW PF1MNB CF5AA CK3BA See notes on page

14 EVAPORATOR CFM EWB DETAILED COOLING CAPACITIES* Continued CONDENSER ENTERING TEMPERATURES F Sens kw** Sens kw** Sens kw** Sens kw** Sens PA10JA047-C Outdoor Section With CC5A/CD5AA048 Section kw** Multipliers for Determining the Performance With Other Sections Section Size Power Section Size Power CC5A/CD5AA CK5A/CK5BT CC5A/CD5AC CC5A/CD5AW CK5A/CK5BW CK5A/CK5BX CD5AA PF1MNA CE3AA CF5AA CK3BA PF1MNB CK5A/CK5BA PA10JA048-C, D Outdoor Section With CC5A/CD5AA048 Section Multipliers for Determining the Performance With Other Sections Section Size Power Section Size Power CC5A/CD5AA CK5A/CK5BA CC5A/CD5AC CC5A/CD5AW CK5A/CK5BT CD5AA CK5A/CK5BW CE3AA CK5A/CK5BX PF1MNB CF5AA CK3BA See notes on page

15 EVAPORATOR CFM EWB DETAILED COOLING CAPACITIES* Continued CONDENSER ENTERING TEMPERATURES F Sens kw** Sens kw** Sens kw** Sens kw** Sens PA10JA060-C Outdoor Section With CC5A/CD5AA060 Section kw** Multipliers for Determining the Performance With Other Sections Section Size Power Section Size Power CC5A/CD5AA PF1MNA CC5A/CD5AW PF1MNA CE3AA PF1MNA CK3BA PF1MNB CK5A/CK5BA PF1MNB CK5A/CK5BT PF1MNB CK5A/CK5BX * Detailed cooling capacities are based on indoor and outdoor unit at same elevation per ARI standard 210/ If additional tubing length and/or indoor unit is located above outdoor unit, a slight variation in capacity may occur. and sensible capacities are net capacities. Blower motor heat has been subtracted. Sensible capacities shown are based on 80 F (27 C) entering air at the indoor coil. For sensible capacities at other than 80 F (27 C), deduct 835 Btuh (245 kw) per 1000 CFM (480 L/S) of indoor coil air for each degree below 80 F (27 C), or add 835 Btuh (245 kw) per 1000 CFM (480 L/S) of indoor coil air per degree above 80 F (27 C). When the required data falls between the published data, interpolation may be performed. ** Unit kw is total of indoor and outdoor unit kilowatts. 15

16 SYSTEM DESIGN 1. Intended for outdoor installation with free air inlet and outlet. Outdoor fan external static pressure available is less than 0.01-in. wc. 2. Minimum outdoor operating air temperature without low-ambient operation accessory is 55 F (12.8 C). 3. Maximum outdoor operating air temperature is 125 F (51.7 C). 4. For reliable operation, unit should be level in all horizontal planes. 5. Maximum elevation of indoor coil above or below base of outdoor unit is: indoor coil above = 50 ft, indoor coil below = 150 ft. 6. For interconnecting refrigerant tube lengths greater than 50 ft or 20 ft vertical differential, consult Long-Line Application Guideline available from equipment distributor. 7. Crankcase heater required when interconnecting refrigerant tube length exceeds 50 ft. 8. If any refrigerant tubing is buried, provide a minimum 6 in. vertical rise to the valve connections at the unit. Refrigerant tubing lengths up to 36 in. may be buried without further consideration. For buried lines longer than 3 ft, consult your local distributor. 9. Use only copper wire for electric connection at unit. Aluminum and clad aluminum are not acceptable for the type of connector provided. SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE UNIT MUST BE INSTALLED IN ACCORDANCE WITH INSTALLATION INSTRUCTIONS Cancels: SS-PA Payne Heating & P.O. Box 70, Indianapolis, IN 406 PRINTED IN U.S.A. Catalog No. 52PA