ß For cement-retained crowns and bridges. Note: synocta cementable abutments. ß Can be especially helpful with large multi-unit cases Note:

Transcription

1 Choosing the correct Straumann abutment for crowns, bridges, and bars Straumann abutments are torqued to 35 Ncm by using the ratchet with torque control device and the appropriate abutment driver. Abutments for use with Abutments for use with Indications (Regular Neck) implants (Wide Neck) implants 6 Solid abutments (all solid abutments have a 6 taper) 7.0 mm ß For crowns and bridges yellow grey blue green brown Note: Abutments for use with crowns and bridges should not be used with implants that have been placed more than 2.0 mm below the subgingival margin. Straumann offers different prosthetic options for subgingival cases. The synocta prosthetic system allows the impression to be taken at the implant level before an abutment is placed, allowing abutment selection to be evaluated on the model with plastic planning parts. Straumann s synocta abutments can ONLY be used with Straumann implants that have the internal octagon configuration (identified by the 043. and 033. prefix of the implant article number). 1.5 mm mm synocta cementable abutments ß For crowns and bridges ß Can be especially helpful with large multi-unit cases Note: synocta cementable abutments can be shortened occlusally by a maximum of 2.0 mm. synocta 1.5 mm abutments ß For crowns and bridges (can also be used with a gold coping to fabricate a custom abutment for a restoration) ß For bar-retained overdentures 6.7 mm, long 6.7 mm, long 5.7 mm, short 5.7 mm, short , short, A , short, B , long, A , long, B 4.25 mm mm , short, A , short, B , long, A , long, B , A , B synocta angled abutments ß For cement or crowns and bridges ( is for ONLY) ß For cases with angulation problems Note: The short synocta angled abutments are 1.0 mm shorter than the long and cannot be modified. synocta transversal abutment ß For lingual crowns and bridges ß Transversal screw retention is used in cases where occlusal screw retention is not feasible due to esthetic requirements and/or axial alignment of the screw. synocta gold abutment ß For cement or crowns ß Ideal for the fabrication of a custom restoration ß Is good for the esthetic region

2 Component stack sheet Cement-retained restorations 7.0 mm minimum vertical height required for a porcelain fused to metal restoration 1 minimum vertical height required for a porcelain fused to metal restoration 1 Minimum vertical height of 6.0 mm is required for an all-metal restoration (synocta cementable abutments can be shortened occlusally by a maximum of 2.0 mm, which would allow for a porcelain fused to metal restoration with a minimum vertical height requirement of 5.0 mm.) 2 3 Minimum vertical height of 4.5 mm is required for an all-metal restoration ( solid abutments can be shortened occlusally by a maximum of 1.0 mm, which would allow for a porcelain fused to metal restoration with a minimum vertical height requirement of 4.5 mm.) synocta plastic coping 2. synocta cementable abutment 3. Straumann implant 1. Plastic coping 2. Solid abutment 3. Straumann implant Custom abutment restoration 4.25 mm 5.75 mm minimum vertical height required for a porcelain fused to metal restoration 1 NOTE: Other types of restorations with the Straumann Dental Implant System may have different height requirements. NN Narrow Neck (Ø 3.5 restorative platform) Regular Neck (Ø 4.8 mm restorative platform) Wide Neck (Ø 6.5 mm restorative platform) Minimum vertical height of 4.75 mm is required for an all-metal restoration synocta occlusal screw 2. synocta gold abutment 3. Straumann implant International Headquarters Institut Straumann AG Peter Merian-Weg 12 CH-4002 Basel, Switzerland Phone +41 (0) Fax +41 (0) North American Distributors Straumann USA, LLC 60 Minuteman Road Andover, MA Phone 800/ / Fax 978/ Straumann Canada Limited 4145 North Service Road, Suite 303 Burlington, ON L7L 6A3 Phone 800/ / Fax 905/ Straumann products are CE marked 8/07 USLIT 097

3 PROSTHETIC OPTIONS

4 NN (Narrow Neck) Straumann Dental Implant System Ø 3.5 mm System Overview P ROSTHETICS Narrow Neck Transfer parts Solid V V /061/062V /161/162 or Prosthetic restoration V V4 Plastic planning parts V V V /927/928V4 Abutments Temporary restoration/ protective caps/healing caps / /048/049V4 Titanium copings/ matrices Gold copings/ matrices Plastic copings / Auxiliary parts/screws V4 Transfer aids crown bridge bar not for hollow cylinder implants, 15

5 (Regular Neck) Ø 4.8 mm synocta O V V or V V4 / /917/918/919V / /613/617/ / u /923/924/925V V /611/615/ u retentive a / V V V V4 V2 = 2 components per pack V V4 V4 = 4 components per pack V4 V20 = 20 components per pack V4

6 (Wide Neck) Ø 6.5 mm Overdenture 09 anchor Solid V4 synocta / V4 LOCATOR / / / V V V V V V V V V