the perfect fusion Catalogue

Transcription

1 the perfect fusion Catalogue

2

3 Valladolid, June 2014 Dear Doctors, We are pleased to introduce our new MG In-Hex Catalogue Castilla y León Young Businessman of the Year Award. Valladolid 2003 Established in Valladolid (Spain) in 1996, Mozo-Grau was created to offer a service by developing, researching, designing and launching new reliable products and solutions for the field of implantological oral surgery, based on the experience of respected professionals. AQVA Quality and Business Management Award. Madrid 2003 Quality, innovation, and science are among the fundamental bases on which Mozo Grau sets its activities. Mozo Grau has been audited and certified to be in conformance with local, European and international standards. Its high quality standards demand parts to be produced with specifications accurate to within 10 microns (0.01 mm) and 100% verification of the parts manufactured to pass through a series of rigorous tests before shipping. The Bizz Award for Excellence in Quality Houston -Texas (USA) 2005 Entrepeneur of the year award. Castilla y Leon 2012 As evicence of what science means to Mozo-Grau is our Scientific Summary which gathers over 50 scientific articles on experimental and clinical studies, and a collection of selected clinical cases performed with Mozo Grau dental implants. The best guarantee of Mozo-Grau quality and constant improvement is the research team s trust and confidence. As for innovation, Mozo Grau is focused in increasing the added value of its production and quality. In this regard, Mozo Grau has launched MG Código Explorer, a unique numeric code which identifies every single MG dental implant. This code allows doctor and patient to have full traceability and knowledge of the implant. Patients receive their Código Explorer on a MG Implant Card, a very comfortable form to carry information everywhere (see page 11 for further information). Enterpreneur of the Year Award (Category: Industry). Castilla y León 2012 Quality Award. Executive Magazine 2013 p. 3

4 Quality Quality: Mozo-Grau Principle The definition of the Spanish Royal Academy of the Language for quality is: property or set of inherent properties to a thing that allow to appreciate it like equal, better or worse than the rest of its type. The strict reading of this definition places the quality of a product as a comparison to the quality offered by its competitors. At Mozo-Grau this comparison is not enough. Our aim is not only to be better than the rest, but to work to satisfy our clients by offering the most advanced science and techniques. Our Quality Control and Engineering Department set up analysis systems and verification procedures to avoid mistakes from the first stages of production. In this way we are able to develop solid and efficient processes that guarantee 100% reliability on all the products and services. ISO 13485:2003 is an ISO standard, published in 2003, that represents the requirements for a comprehensive management system for the design and manufacture of medical devices. The Medical Devices Directive (Council Directive 93/42/EEC) is intended to harmonize the laws related to medical devices within the European Union. ISO 9001:2008 requires the organization to demonstrate continuous improvement. The CE marking (also known as CE mark) is a mandatory conformity mark on many products placed on the single market in the European Economic Area (EEA). Mozo-Grau complies with all these mandatory certifications and regulations necessary to supply implants in the European Union, moreover Mozo Grau is voluntarily complying with the most exigent standards on the subject. At Mozo-Grau we are proud of the trust placed on us by our clients every time they purchase one of our products. This confidence compels us to meet their expectations. The best quality control any company can have is a satisfied client. p. 4

5 Quality Quality: International Certificates CE Marking ISO : 2012 ISO 9001 : 2008 COLOMBIA VENEZUELA MEXICO TAIWAN RUSSIA CHINA p. 5

6 Index MG-InHex Catalogue MG-INHEX Implants MG-INHEX Prostheses SURGICAL MATERIALS Introduction 3 Quality 4 The Perfect Fusion 7 Scientific Support 8 MG Vial manipulation 10 Código Explorer 11 MG-INHEX Implants MG-INHEX Implant MG-INHEX Implant MG-INHEX Implant MG-INHEX Implant 17 MG-Inhex Prosthetic System 19 Prostheses scheme 20 Tools for prostheses and screwdrivers 25 MINI MG-INHEX Prosthetic System 26 STANDARD MG-INHEX Prosthetic System 28 MAXI MG-INHEX Prosthetic System 34 MG-INHEX Temporary prostheses/immediate Loading 40 Screws for abutment and transfers 43 Surgical Material 45 Instructions for maintenance of surgical instruments 46 Surgical kits 47 Drills for implants 48 Drills for implants and RCD stop kit 50 Bone Expansion 53 Accessories 54 Abbreviations Abut. Abutment cc Cubic centimeters cm centimeter C/A Contra-Angle Diff. Sit. Difficult Situations H Height Impr. Impression mm Millimeters Ncm Newtons per centimeter Prep. Prepable ret. Retaining rpm Revolutions per minute STD Standard Tap. Tapered w/s With screw

7 the perfect fusion With MG-InHex Implant, Mozo-Grau has achieved a solution based on well established scientific results and respecting surgical, biological and prosthetic principles thus ensuring a very aesthetic result. The ease of manipulation and the strength of the materials of the MG-InHex implant allows the clinician to achieve predictable aesthetic results with the security and reliability provided by its high rate of success, based on solid osseointegration and ideal distribution of the biomechanical loads. The trunk and cone profile design of the implant allows its walls to provide sufficient resistance to respond to axial and paraxial occlusion loads with guarantees. The Microthreads in the cortical part, which become threads in the central part, together with the self-tapping design of the apex end, make this implant one of the most stable at insertion in the market. Moreover, the proven efficiency of the RBM treated surface to achieve secondary or biological stability, makes the MG-InHex Implant the best option for immediate loading applications. The internal connection of MG-InHex implant is based on the use of Morse Cone, which reliably ensures the correct stability and solidity in the abutment, without loss of flexibility when planning the restoration. At Mozo-Grau we are very satisfied with the versatility that the MG-InHex Implant offers and we are sure it will meet the most demanding expectations of all the clinical professionals and technicians in the sector. The location of the internal connection point between the implant and the abutment, together with the design of the microthreads in the coronal portion, respect the biological principles that ensure a correct reaction from the perimplant bone. On the other hand, the 45º shoulder has been proven as the best solution in regard to the soft tissues treatment. All these proven principles lead to the achievement of an optimum aesthetic result. micron accuracy p. 7

8 Implantology. Implants. MG-InHex MG-InHex INTERNAL CONNECTION 11º Morse taper double internal hexagon. PLATFORM SWITCHING Respect for the biological principles. MICROTHREADS Reducing marginal bone remodelation. 45º IMPLANT SHOULDER Aesthetic soft tissues. RBM SURFACE TREATMENT Predictable osseointegration. (Success rate 98,2%*) SURFACE TREATMENT UP TO THE IMPLANT COLLAR Evolution of science. LOADING RESISTANCE Strength of material. IMPLANT MORPHOLOGY Self taping, conical apex and V-shape threads. IMMEDIATE LOADING Suitable for the treatment. * According to the multicentric prospective study published in Official Journal of the Spanish Oral and Maxillofacial Surgery Association (published Sept-Oct 2009). 1,475 implants placed, 654 prostheses over 480 patients, 2.5 years follow up. p. 8

9 Implantology. Implants. MG-InHex MG-InHex List of Studies A SOLID BASE: OVER 50 SCIENTIFIC STUDIES AND ARTICLES For more information about the scientific principles that support the MG-InHex implant design, please refer to, among others, the following scientific articles: MICROLEAKAGE OF THE PROSTHETIC ABUTMENT/IMPLANT INTERFACE WITH INTERNAL AND EXTERNAL CONNECTION: IN VITRO STUDY Carlos Larrucea Verdugo et al. University of Talca, Chile. Publication: Clinical Oral Implant Research. Article first published online 4 July 2013 Conclusion:...the lower levels of microleakage occur in 30N tightened abutments, where, as shown in the photomicrographs, the gap is virtually nonexistent for Morse taper connections and external connections get an almost perfect seal. This may be due to the strict manufacturing criteria found in the analysed elements. MG-InHex internal connection photomicrograph. Courtesy of Dr. Carlos Larrucea INFLUENCE OF IMPLANT NECK DESIGN AND IMPLANT-ABUTMENT CONNECTION TYPE ON PERI-IMPLANT HEALTH. RADIOLOGICAL STUDY Miguel Peñarrocha Diago et al. University of Valencia, Spain. Publication: Clinical Oral Implant Research. Vol. 24, Issue 11, pages , November 2013 Conclusion:...Global mean marginal bone loss with Osseous was 0.27 ± 0.43 mm and 0.38 ± 0.51 mm as determined 6 and 12 months after prosthetic loading, respectively, whereas in the case of Inhex was 0.07 ± 0.13 and 0.12 ± 0.17 mm... Anyway, in both groups, the value obtained were within normal ranges described in the literature Measurement of peri-implant marginal bone loss. Courtesy of Dr. Miguel Peñarrocha p. 9

10 Implantology. MG Vial manipulation MG Vial manipulation PLACEMENT OF THE IMPLANT WITH THE CONTRA ANGLE Open the blister Remove the vial Vial Unscrew the plastic cap Pick up the implant with the C/A Place the implant in the alveolus Open the cap flip-top Extract the cover screw Place the cover screw MANUAL PLACEMENT OF THE IMPLANT Open the blister Remove the vial Vial Unscrew the plastic cap Load the implant Place the implant in the alveolus* See the Hex. hand wrench on page 51 Remove the hand wrench Open the cap flip top Extract the cover screw Place the cover screw p. 10

11 Implantology. Código Explorer Your Implant, your Code Every Mozo Grau dental implant is identified with a Código Explorer, a unique numeric code that will allow you to have full traceability and knowledge of your implant. IMPLANT CARD Traceability as never seen before Código Explorer ensures 100% traceability of every Mozo Grau implant leading to doctor s and patient s peace of mind. Enter your Código Explorer in Mozo Grau website ( to download a Certificate of Quality showing full information about your implant. Patients receive their Código Explorer on a Mozo Grau Implant Card, a very comfortable form to carry information everywhere. p. 11

12

13 MG-InHex Implants

14 Implantology. Implants. MG-InHex Implants 3. MINI MG-INHEX Implant mount shows millimeter marks and hexagon position MG-INHEX x 10 mm MINI MG-INHEX Implant 3.3 x 11.5 mm MINI MG-INHEX Implant 3.3 x 1 MINI MG-INHEX Implant 3.3 x 15 mm MINI MG-INHEX Implant MG-INHEX MINI Cover screw *Do not tighten at torque values higher than 10 Ncm - Double Internal Hexagon - R.B.M. Treated Surface - Implant Platform: 2.30 mm - Implant Diameter: 3. - Internal thread: 1.4 mm - Internal Morse Cone 11º - Microthreads - Material: Grade V Titanium - Cover screw included in each implant - Implant mount included - No touch sterile package DRILLING SEQUENCE A standard drilling sequence will be needed and the 3.0 mm drill will be the final one to be used (recommended drilling speed: rpm). It is suggested to use the profile drill at 800 rpm. Being the implant self-tapping, on very cortical bones (symphysis area) it is recommended to use the drills for hard bones, and, if considered necessary, use the 3. bone tap to avoid overheating the bone and to facilitate the implant insertion. The use of copious internal irrigation is suggested, too. It is recommended to place the implants at torque values between Ncm. Locator drill 2.0 mm 3.0 mm Profile Drill 3.2 mm hard bone drill Bone Tap (for very cortical bones) rpm 800 rpm rpm 15 rpm p. 14

15 Implantology. Implants. MG-InHex Implants 3.75 mm STANDARD MG-INHEX Implant mount shows millimeter marks and hexagon position MG-INHEX x 8 mm STD MG-INHEX Implant 3.75 x 10 mm STD MG-INHEX Implant 3.75 x 11.5 mm STD MG-INHEX Implant 3.75 x 1 STD MG-INHEX Implant 3.75 x 15 mm STD MG-INHEX Implant MG-INHEX STD Cover screw *Do not tighten at torque values higher than 10 Ncm - Double Internal Hexagon - R.B.M. Treated Surface - Implant Platform: 2.80 mm - Implant Diameter: 3.75 mm - Internal thread: 1.6 mm - Internal Morse Cone 11º - Microthreads - Material: Grade IV Commercially Pure Titanium - Cover screw included in each implant - Implant mount included - No touch sterile package DRILLING SEQUENCE A standard drilling sequence will be needed and the 3. drill will be the final one to be used (recommended drilling speed: rpm). It is suggested to use the profile drill at 800 rpm. Being the implant self-tapping, on very cortical bones (symphysis area) it is recommended to use the drills for hard bones, and, if considered necessary, use the 3.75 mm bone tap to avoid overheating the bone and to facilitate the implant insertion. The use of copious internal irrigation is suggested, too. It is recommended to place the implants at torque values between Ncm. p. 15 Locator drill 2.0 mm 3.0 mm 3. Profile Drill 3.5 mm hard bone drill Bone Tap (for very cortical bones) rpm 800 rpm rpm 15 rpm

16 Implantology. Implants. MG-InHex Implants 4.25 mm STANDARD MG-INHEX Implant mount shows millimeter marks and hexagon position MG-INHEX x 8 mm STD MG-INHEX Implant 4.25 x 10 mm STD MG-INHEX Implant 4.25 x 11.5 mm STD MG-INHEX Implant 4.25 x 1 STD MG-INHEX Implant 4.25 x 15 mm STD MG-INHEX Implant MG-INHEX STD Cover screw *Do not tighten at torque values higher than 10 Ncm - Double internal hexagon - R.B.M. treated surface - Implant Platform: 2.80 mm - Implant Diameter: 4.25 mm - Internal Thread: 1.6 mm - Internal Morse Cone 11º - Microthreads - Material: Grade IV Commercially Pure Titanium - Cover screw included in each implant - Implant mount included - No touch sterile package - Soft Bones (Type IV), Posterior Sectors DRILLING SEQUENCE A standard drilling sequence will be needed and the 3.8 mm drill will be the final one to be used (recommended drilling speed: rpm). It is suggested to use the profile drill at 800 rpm. Being the implant self-tapping, on very cortical bones (symphysis area) it is recommended to use the drills for hard bones, and, if considered necessary, use the 4.25 mm bone tap to avoid overheating the bone and to facilitate the implant insertion. The use of copious internal irrigation is suggested, too. It is recommended to place the implants at torque values between Ncm. p. 16 Locator drill 2.0 mm 3.0 mm mm Profile Drill 4.0 mm hard bone drill Bone Tap (for very cortical bones) rpm 800 rpm rpm 15 rpm

17 Implantology. Implants. MG-InHex Implants 5.0 mm MAXI MG-INHEX MG-INHEX Implant mount shows millimeter marks and hexagon position x 9 mm MAXI MG-INHEX Implant 5.0 x 10 mm MAXI MG-INHEX Implant 5.0 x 11.5 mm MAXI MG-INHEX Implant 5.0 x 1 MAXI MG-INHEX Implant 5.0 x 15 mm MAXI MG-INHEX Implant MG-INHEX MAXI Cover screw *Do not tighten at torque values higher than 10 Ncm - Double Internal Hexagon - R.B.M. Treated Surface - Implant Platform: 3.80 mm - Implant Diameter: 5.0 mm - Internal Thread: 2.0 mm - Internal Morse Cone 11º - Microthreads - Material: Grade IV Commercially Pure Titanium - Cover screw included on each implant - Implant mount included - No touch sterile package - Soft Bones (Type IV), Posterior Sectors, immediate post-extraction sites DRILLING SEQUENCE A standard drilling sequence will be needed and the 4.7 mm drill will be the final one to be used (recommended drilling speed: rpm). Drills wider than 4. are recommended to be used at 400 rpm. It is suggested to use the profile drill at 800 rpm. Being the implant self-tapping, on very cortical bones (symphysis area) it is recommended to use the drills for hard bones, and, if considered necessary, use the 5.0 mm bone tap to avoid overheating the bone and to facilitate the implant insertion. The use of copious internal irrigation is suggested, too. It is recommended to place the implants at torque values between Ncm. p. 17 Locator drill 2.0 mm 3.0 mm mm mm Profile Drill 4.9 mm hard bone drill Bone Tap (for very cortical bones) rpm 400 rpm 800 rpm 400 rpm 15 rpm

18

19 MG-InHex Prosthetic System Prostheses scheme Screwdrivers and tips Healing abutments Impression copings Direct to implant abutments Abutment for Zirconium Ball and Locator abutments Transmucosal (Tapered) Temporary Prostheses / Immediate Loading Screws for Abutments and Transfers

20 Unitary Restoration Cemented Hex prepable abutment Screw Hex gold base UCLA abutment Cemented Hex / Non-Hex gold base UCLA abutment Multiple restoration (fixed) Screw Direct to implant Hex / Non-Hex gold base UCLA abutment 10º Tapered abutment Straight 30º Tapered abutment Transmucosal ABUTMENT FOR ZIRCONIUM Angled 17º angled tapered abutment MG-INHEX Implants Direct to implant Ball abutment Ball abutment Inhex Overdenture (removable) Locator Locator abutment (includes processing pack) Healing abutment Bars Non-Hex gold base UCLA abutment Aesthetic Healing abutment Straight 10º Tapered abutment 30º Tapered abutment Transmucosal Retaining Cap for Tapered Abutment (10º-30º). 2 pcs. Angled 17º angled tapered abutment Tapered abutment cap Angled 17º Direct to implant Unitary Temporary hex castable UCLA abutment Tapered Abutment Cap (10º-30º) Immediate Temporary Restoration Multiple Temporary non hex castable UCLA abutment MINI Platform STANDARD Platform Straight Tapered abutment (10º - 30º) MAXI Platform Transmucosal All the anti-rotational castable abutments are manufactured * in red colour for an easy identification. Angled 17º angled tapered abutment p. 20

21 Aesthetic hex prepable abutment Angled abutment (15º - 20º) Abutment for Zirconium Hex titanium UCLA abutment (weld with titanium) Hex / Non-Hex prepable abutment Aesthetic hex prepable abutment Angled abutment (15º - 20º) Abutment for Zirconium Hex / Non-Hex prepable abutment (weld with titanium) Aesthetic hex prepable abutment (weld with titanium) Rotational castable post for tapered abutment (10º - 30º) Rotational titanium post for tapered abutment (10º - 30º) 10º Anti-rotational castable post for tapered abutment 10º Anti-rotational titanium post for tapered abutment Castable post for 17º angled tapered abutment Titanium post for 17º angled tapered abutment Plastic cap Rotational castable post for tapered abutment (10º - 30º) Rotational titanium post for tapered abutment (10º - 30º) 10º Anti-rotational castable post for tapered abutment 10º Anti-rotational titanium post for tapered abutment Castable post for 17º angled tapered abutment Titanium post for 17º angled tapered abutment Temporary titanium hex UCLA abutment Temporary prepable hex abutment Temporary titanium non-hex UCLA abutment Temporary prepable non-hex abutment Temporary castable post for tapered abutment (10º - 30º) Temporary titanium post for tapered abutment (10º - 30º) Castable post for 17º angled tapered abutment Titanium post for 17º angled tapered abutment p. 21

22 Customized prosthesis MG Bio-CAM MG Bio-CAM

23 Mozo-Grau offers more: Quality Reliability Perfect adjustment Peace of mind Accuracy Now more connections available: Branemark type ; Straumann ; Nobel Replace ; Zimmer ; Astra Tech... New! Simply perfect

24

25 Prostheses. Prosthetic System MG-InHex Prosthetic System MG-InHex 100% of all the stages necessary for the production of the prosthesis for our implant system are subject to strict quality controls. High precision machinery, with ±0.005 mm margin error and ±0.01 mm tolerance, is used to produce the prosthetic abutments. Unless expressly specified in any section, the material used for producing the abutments is Grade V Titanium (TiAI 6 V 4 ) TORQUE WRENCHES Dynamometrical manual wrench. Variable Tightening torque from 10 to 35 Ncm 20 Ncm torque wrench 30 Ncm torque wrench Dynamometric ratchet wrench 45 Ncm. - To assure the precise tightening of all the prosthetic screws - For a bigger comfort when working in the posterior zone - Tightening Torque: 30 Ncm for MG-InHex prostheses 30 Ncm for MG-Osseous prostheses SCREWDRIVERS AND TIPS mm short Hex. Screwdriver. Length 8 mm 1.25 mm long Hex. Screwdriver Length 14 mm 14 mm flat screwdriver 1.25 mm short Hex. Screwdriver tip. Length 7 mm 1.25 mm long Hex. Screwdriver tip. Length 12 mm 12 mm flat screwdriver tip 1.25 mm short C/A Hex. Screwdriver. Length 9 mm 1.25 mm long C/A Hex. Screwdriver. Length 14 mm 14 mm C/A flat screwdriver Locator Core Tool 1.25 mm Hex Screwdriver - Used for: Cover screw, implant mount, healing abutment, impression coping, tapered abutment, ball abutment, prosthetic screw, twist drills with stop Screwdriver tip mm Hex Screwdriver - Used for: Cover screw, implant mount, healing abutment, impression coping, tapered abutment, ball abutment, prosthetic screw, twist drills with stop - Used with: ratchet wrench, torque wrench, hand wrench p. 25

26 Prostheses. Prosthetic System MG-InHex Mini MG-InHex Prosthetic System MINI MG-INHEX HEALING ABUTMENTS MINI MG-INHEX Healing abutment MG-INHEX MINI CUFF HEIGHT (H) 2 mm H - Platform: 2.30 mm - : 3. - Screwdriver: Hex 1.25 mm Healing abutment MG-INHEX MINI Healing abutment MG-INHEX MINI 4 mm - It is convenient to leave the cuff 2 mm above the soft tissue - Maximum tightening torque 10 Ncm. MINI MG-INHEX IMPRESSION COPINGS MINI MG-INHEX [ Hex ] Hex Impr. Coping w/s for MG-INHEX MINI Short transfer screw MG-INHEX MINI A L - Stainless Steel - Screwdriver: Hex 1.25 mm - Platform: 2.30 mm - Impression coping: L=1, A=11 mm - Short transfer screw: L= 17 mm, A=9 mm - : 3. [ Hex ] - For single or multiple restorations - Used for open or closed tray MINI MG-INHEX IMPLANT ANALOG MINI MG-INHEX Implant Analogue MG-INHEX MINI - Platform: 2.30 mm - : 3. - Stainless Steel - One single use p For hex closed tray use short transfer screw - Maximum tightening torque 10 Ncm. [ No Hex ] - For multiple restorations - Used for closed tray

27 Prostheses. Prosthetic System MG-InHex Mini MG-InHex Prosthetic System MINI MG-INHEX HEX PREPABLE ABUTMENT MINI MG-INHEX [ Hex ] Hex Prep. Abutment w/s for MG-INHEX MINI Hex Prep. Abutment w/s for MG-INHEX MINI Hex Prep. Abutment w/s for MG-INHEX MINI * Abutments are also available without screw. CUFF HEIGHT (H) 1 mm 2 mm 6.5 mm H - Titanium Grade V abutment that can be cut - Attaches directly to implant - For single or multiple restorations - For cement retained restorations - Platform: 2.30 mm - : 3.70 mm - Screwdriver: 1.25 mm Hex - Soft tissue height must be above the abutment ring height - Torque 30 Ncm. MINI MG-INHEX ANGLED PREPABLE ABUTMENT MINI MG-INHEX [Hex] º Angled prep. abut. w/s for MG-INHEX MINI 20º Angled prep. abut. w/s for MG-INHEX MINI CUFF HEIGHT (H) 2 mm 2 mm 6.5 mm p. 27 H - Titanium Grade V abutment that can be cut - Attaches directly to implant - For single or multiple restorations - For cement retained restorations - Used to correct disparallelism - Platform: 2.30 mm - : 3.7 mm - Screwdriver: 1.25 mm Hex. - Soft tissue height must be above the abutment ring height - Torque 30 Ncm

28 Prostheses. Prosthetic System MG-InHex Standard MG-InHex Prosthetic System STANDARD MG-INHEX HEALING ABUTMENTS STANDARD MG-INHEX Healing abutment MG-INHEX STD CUFF HEIGHT (H) 2 mm - Platform: 2.80 mm - : 4.0 mm - Screwdriver: Hex 1.25 mm Healing abutment MG-INHEX STD Healing abutment MG-INHEX STD 4 mm H - It is convenient to leave the cuff 2 mm above the soft tissue - Maximum tightening torque 10 Ncm Healing abutment MG-INHEX STD 5 mm Healing abutment MG-INHEX STD 6 mm Healing abutment MG-INHEX STD 7 mm STANDARD MG-INHEX AESTHETIC HEALING ABUTMENTS STANDARD MG-INHEX CUFF HEIGHT (H) Aesthetic healing abutment for MG-INHEX STD Aesthetic healing abutment for MG-INHEX STD Aesthetic healing abutment for MG-INHEX STD Aesthetic healing abutment for MG-INHEX STD 4 mm 5 mm 6 mm H - Platform: 2.80 mm - : 6.0 mm - Screwdriver: Hex1.25 mm Recommendation for use: - It is convenient to leave the cuff 2 mm above the soft tissue - Maximum tightening torque 10 Ncm Aesthetic healing abutment for MG-INHEX STD 7 mm STANDARD MG-INHEX IMPRESSION COPINGS STANDARD MG-INHEX p. 28 [ Hex ] [ Non Hex ] Hex Impr. Coping w/s for MG-INHEX STD Aesthetic Hex Impr. Coping w/s for MG-INHEX STD Long Hex Imp Coping w/s for MG-INHEX STD Non-Hex Impr. Coping. for MG-INHEX STD Aesthetic Non-Hex Impr. Coping for MG-INHEX STD Long Non-Hex Impr. Coping for MG-INHEX STD A A L L - Stainless Steel - Screwdriver: Hex 1.25 mm - Platform: 2.80 mm [ Hex ] - For single or multiple restorations - Used for open or closed tray - Supplied with screw Ref (see page 43) - For hex closed tray use short transfer screw (Page 45, order separately) - Hex impression coping: : 4.1 mm L= 13.5 mm A=11 mm - Aesthetic Hex impression coping: : 6.0 mm L= 13.5 mm A=11 mm - Long Hex impression coping: : 4.1 mm L= 17 mm A=15 mm [ Non Hex ] - For multiple restorations - For closed tray only - Non-hex impression coping: : 4.1 mm L=16.30 mm A=11 mm - Aesthetic non-hex impression coping: : 6.0 mm L=16.30 mm A=11 mm - Long non-hex impression coping: : 4.1 mm L=19.30 mm A=14 mm - Maximum tightening torque 10 Ncm.

29 Prostheses. Prosthetic System MG-InHex Standard MG-InHex Prosthetic System STANDARD MG-INHEX IMPLANT ANALOG STANDARD MG-INHEX Implant Analogue MG-INHEX STD Analog wrench MG-INHEX STD - Platform: 2.80 mm - : 4.0 mm - Stainless Steel - One single use Analog wrench To hold the abutment or crown for a comfortable handling at lab or clinic STANDARD MG-INHEX UCLA ABUTMENT STANDARD MG-INHEX TITANIUM Non-Hex Titanium UCLA w/s for MG-INHEX STD - Titanium Grade V abutment - Attaches directly to implant - For cement retained or screw retained restorations - Platform: 2.80 mm - : 4.1 mm - Screwdriver: 1.25 mm Hex Hex Titanium UCLA w/s for MG-INHEX STD A= 10 mm - Hex abutment is recommended for unitary restorations - Maximum tightening torque 20 Ncm. - Ensures a correct fit of the abutment to the implant GOLD Hex GOLD BASE UCLA w/s for MG-INHEX STD (Gold 60/19) Non-Hex GOLD BASE UCLA w/s for MG-INHEX STD (Gold 60/19) A= 10 mm A= 2,7 mm - Hex Castable UCLA with Gold Base abutment - Attaches directly to implant - For cement retained or screw retained restorations - Platform: 2.80 mm - : 4.1 mm - Screwdriver: 1.25 mm Hex. - Cast using Gold alloys 60/19 - Melting temperature 1415ºC * Abutments are also available without screw. * Hex castable abutments are red-coloured for an easy identification. - Ensures a correct fit of the abutment to the implant - Maximum tightening torque 20 Ncm. ABUTMENT FOR ZIRCONIUM Abutment for Zirconium w/s MG-INHEX STD Includes one Sirona s CEREC 3D scanbody 0, Scanbodies (3 pcs each pack)* Compatible with Sirona s CEREC 3D TITANIUM BASE FOR CAD/CAM. For production of customized mesostructures by CAD/CAM techniques Mozo-Grau abutment for Zirconium allows the professional to carry out customized restorations using Zirconium over Mozo-Grau implants with the highest possible accuracy. The abutment for Zirconium can be used as base to cement zirconium structures or mesostructures for unitary or multiple restoration cases, achieving the best possible passive adjustment that allows a safe, predictable and aesthetic result. Mozo-Grau abutment for Zirconium can be scanned by some of the best scanners currently in the market allowing the use of modern software for infographic design. p. 29

30 Prostheses. Prosthetic System MG-InHex Standard MG-InHex Prosthetic System STANDARD MG-INHEX HEX PREPABLE ABUTMENT STANDARD MG-INHEX [ Hex ] Hex Prep. Abutment w/s for MG-INHEX STD Hex Prep. Abutment w/s for MG-INHEX STD Hex Prep. Abutment w/s for MG-INHEX STD Hex Prep. Abutment w/s for MG-INHEX STD Hex Prep. Abutment w/s for MG-INHEX STD CUFF HEIGHT (H) 0 mm 1 mm 2 mm 4 mm 6,5 mm H - Titanium Grade V abutment that can be cut - Attaches directly to implant - For single or multiple restorations - For cement retained restorations - Platform: 2.80 mm - : 4 mm - Screwdriver: 1.25 mm Hex - Soft tissue height must be above the abutment ring height - Torque 30 Ncm. * Abutments are also available without screw. STANDARD MG-INHEX AESTHETIC HEX PREPABLE ABUTMENT STANDARD MG-INHEX [ Hex ] Aesthetic Hex Prepable Abutment w/s for MG-INHEX STD Aesthetic Hex Prepable Abutment w/s for MG-INHEX STD * Abutments are also available without screw. CUFF HEIGHT (H) 4 mm A= 6,5 mm H - Titanium Grade V abutment that can be cut - Attaches directly to implant - For single or multiple restorations - For cement retained restorations - Platform: 2.80 mm - : 6.0 mm - Screwdriver: 1.25 mm Hex. - Soft tissue height must be above the abutment ring height - Usable in situations of high aesthetic compromise - Torque 30 Ncm. STANDARD MG-INHEX NON-HEX PREPABLE ABUTMENT STANDARD MG-INHEX [ Non Hex ] Non-Hex Prep. Abutment for MG-INHEX STD CUFF HEIGHT (H) 1 mm Non-Hex Prep. Abutment for MG-INHEX STD Non-Hex Prep. Abutment for MG-INHEX STD Non-Hex Prep. Abutment for MG-INHEX STD 2 mm 4 mm 6,5 mm H p Titanium Grade V abutment that can be cut - Attaches directly to implant - For multiple restorations - For cement retained restorations - Platform: 2.80 mm - : 4 mm - Screwdriver: 1.25 mm Hex [ 2 pieces ] Non-Hex Prep. Abut. w/s for MG-INHEX STD Non-Hex Prep. Abut. w/s for MG-INHEX STD 1 mm 2 mm 6,5 mm - Soft tissue height must be above the abutment ring height - Torque 30 Ncm Non-Hex Prep. Abut. w/s for MG-INHEX STD H Non-Hex Prep. Abut. w/s for MG-INHEX STD 4 mm * Abutments are also available without screw.

31 Prostheses. Prosthetic System MG-InHex Standard MG-InHex Prosthetic System STANDARD MG-INHEX ANGLED PREPABLE ABUTMENT STANDARD MG-INHEX [Hex] º Angled prep. abut. w/s for MG-INHEX STD 15º Angled prep. abut. w/s for MG-INHEX STD 15º Angled prep. abut. w/s for MG-INHEX STD 20º Angled prep. abut. w/s for MG-INHEX STD 20º Angled prep. abut. w/s for MG-INHEX STD 20º Angled prep. abut. w/s for MG-INHEX STD CUFF HEIGHT (H) 1 mm 5 mm 1 mm 5 mm 6,5 mm H - Titanium Grade V abutment that can be cut - Attaches directly to implant - For single or multiple restorations - For cement retained restorations - Used to correct disparallelism - Platform: 2.80 mm - : 4.0 mm - Screwdriver: 1.25 mm Hex. - Soft tissue height must be above the abutment ring height - Torque 30 Ncm STANDARD MG-INHEX BALL ABUTMENT STANDARD MG-INHEX [ Non Hex ] Ball Abutment with Plastic cap for MG-INHEX STD Ball Abutment with Plastic cap for MG-INHEX STD Ball Abutment with Plastic cap for MG-INHEX STD Ball Abutment with Plastic cap for MG-INHEX STD Ball Abutment with Plastic cap for MG-INHEX STD Ball Abutment Analog (stainless steel) CUFF HEIGHT (H) 1 mm 2 mm 4 mm 5.5 mm H - For overdentures - Up to 10º relative divergence between implants - Attaches directly to the implant - Platform: 2.80 mm - : 4.0 mm - Screwdriver: 1.25 mm Hex. - Stainless steel - Torque 30 Ncm - It is convenient to leave the cuff 1 mm above the soft tissue - The use of the Paralleling Guide will help to avoid disparalellism problems when placing the ball abutments Plastic Cap 4 mm 5 mm STANDARD MG-INHEX LOCATOR ABUTMENT STANDARD MG-INHEX [ Non Hex ] Locator Analog - Pack 2 units Locator Abut.and processing package MG-INHEX STD Locator Abut.and processing package MG-INHEX STD CUFF HEIGHT (H) 1 mm 2 mm - For overdentures - Accommodates a divergent implant between 10 and 20 degrees (40 degrees between implants) - Attaches directly to the implant - Platform: 2.80 mm - : 4.0 mm - Use Locator Core Tool - Torque 20 Ncm Locator Abut.and processing package MG-INHEX STD Locator Abut.and processing package MG-INHEX STD Locator Abut.and processing package MG-INHEX STD 4 mm 5 mm - It is convenient to leave the Locator abutment at least 1 mm above the softtissue level - The use of the Paralleling Guide will help to avoid problems when placing the abutments Locator impression coping Pack 4 units. Locator bar attachment processing pack * Males Clear=strong / Pink=light / Blue=Extralight * Males for divergent implants Green=strong / Red=light Locator bar attachment 2mm (2 pack) p. 31

32 Prostheses. Prosthetic System MG-InHex Standard MG-InHex Prosthetic System Transmucosal tapered abutment for screw retained restorations Recommended for immediate loading and compromised cases with damaged periodontal tissues. Eases the exchange of provisional abutments during the immediate loading protocol. Improves the emergency profile and maintains the gingival and osseous level. Avoids the contact of the temporary abutments and impression copings with the wound. Protects the hard and soft perimplantary tissues and eases the prosthetics hygiene. STANDARD MG-INHEX TAPERED ABUTMENT STANDARD MG-INHEX º tapered abutment MG-INHEX STD CUFF HEIGHT (H) 0 mm 2 mm º tapered abutment MG-INHEX STD 10º tapered abutment MG-INHEX STD 10º tapered abutment MG-INHEX STD 10º tapered abutment MG-INHEX STD 10º tapered abutment MG-INHEX STD 30º tapered abutment MG-INHEX STD 30º tapered abutment MG-INHEX STD 1 mm 2 mm 4 mm 5 mm 1 mm 2 mm Flat side that provides an anti-rotational system to the abutment. 0,75 mm H H - For multiple restorations - For overdentures or superstructures - Screw-retained - The 10º or 30ºangle corrects disparallelism - Attaches directly to the implant - Platform: 2.80 mm - : 4.0 mm - Screwdriver: 1.25 mm Hex. - For restorations in soft tissues thicker than - To take impressions is recommendable to use tapered abutments Impression Copings - Torque 30 Ncm º tapered abutment MG-INHEX STD º tapered abutment MG-INHEX STD 4 mm º tapered abutment MG-INHEX STD 5 mm p. 32

33 Prostheses. Prosthetic System MG-InHex Standard MG-InHex Prosthetic System STANDARD MG-INHEX TAPERED ABUTMENTS STANDARD MG-INHEX º anti-rotational castable post for tapered abut. w/s - Castable abutment. - Torque 20 Ncm º rotational castable post for tapered abut. w/s 30º rotational castable post for tapered abut. w/s 11 mm * Anti-rotational castable abutments are manufactured in red colour for an easy identification º anti-rotational titanium post for tapered abut. w/s - Grade V Titanium. - Torque 20 Ncm º rotational titanium post for tapered abut. w/s 30º rotational titanium post for tapered abut. w/s 11 mm * Anti-rotational titanium abutments are manufactured in purple colour for an easy identification º tapered abutment analog - Material: stainless steel º tapered abutment analog / / 30 10º anti-rotational impression coping for tapered abut. w/s 10º / 30º rotational impr. coping for tapered abut. w/s 10º / 30º impression coping for tap. abut. closed tray 11 mm * Anti-rotational abutments are manufactured in purple colour for an easy identification º tapered abutment cap (1 piece) 4,2 mm - Grade V Titanium º tapered abutment cap (1 piece) º angled tapered abutment MG-INHEX STD 2 mm height - Grade V Titanium. - Torque 30 Ncm º angled tapered abutment MG-INHEX STD height 17º angled tapered abutment MG-INHEX STD 4 mm height - Used to correct disparalellism between implants. - Used to restore implants with very divergent emergency angles Rotational castable post for 17º angled tapered abutment w/s - Castable abutment. - Torque 20 Ncm Rotational titanium post for 17º angled tapered abutment w/s - Grade V Titanium. - Torque 20 Ncm Rotational 17º angled tapered abutment analog - Material: stainless steel Rotational impression coping for 17º angled tapered abutment w/s - Material: stainless steel º tapered abutment cap - Grade V Titanium. p. 33

34 Prostheses. Prosthetic System MG-InHex Maxi MG-InHex Prosthetic System MAXI MG-INHEX HEALING ABUTMENTS MAXI MG-INHEX Healing abutment MG-INHEX MAXI CUFF HEIGHT (H) 2 mm - Platform: 3.80 mm - : 4.0 mm - Screwdriver: Hex mm Healing abutment MG-INHEX MAXI Healing abutment MG-INHEX MAXI 4 mm H - It is convenient to leave the cuff 1 mm above the soft tissue - Maximum tightening torque 10 Ncm Healing abutment MG-INHEX MAXI 5 mm Healing abutment MG-INHEX MAXI 6 mm Healing abutment MG-INHEX MAXI 7 mm MAXI MG-INHEX AESTHETIC HEALING ABUTMENTS MAXI MG-INHEX CUFF HEIGHT (H) Aesthetic healing abutment for MG-INHEX MAXI Aesthetic healing abutment for MG-INHEX MAXI 4 mm H - Platform: 3.80 mm - : 6.0 mm - Screwdriver: Hex mm Aesthetic healing abutment for MG-INHEX MAXI Aesthetic healing abutment for MG-INHEX MAXI 5 mm 6 mm Recommendation for use: - It is convenient to leave 1 mm of the cuff above the soft tissue - Maximum tightening torque 10 Ncm Aesthetic healing abutment for MG-INHEX MAXI 7 mm MAXI MG-INHEX IMPRESSION COPINGS MAXI MG-INHEX [ Hex ] [ Non Hex ] Hex Impr. Coping for MG-INHEX MAXI Aesthetic Hex Impr. Coping for MG-INHEX MAXI Long Hex Imp Coping for MG-INHEX MAXI Non-Hex Impr. Coping for MG-INHEX MAXI Aesthetic Non-Hex Impr. Coping for MG-INHEX MAXI A A L L - Stainless Steel - Screwdriver: Hex 1.25 mm - Platform: 3.80 mm Long Non-Hex Impr. Coping for MG-INHEX MAXI p. 34 [ Hex ] - For single or multiple restorations - Used for open or closed tray - Supplied with screw Ref (see page 43) - For hex closed tray use short transfer screw (Page 45, order separately) - Hex impression coping: : 4.1 mm L= 15 mm A=11 mm - Aesthetic Hex impression coping: : 6.0 mm L= 15 mm A=11 mm - Long Hex impression coping: : 4.1 mm L= 18.5 mm A=15 mm [ Non Hex ] - For multiple restorations - For closed tray only - Non-hex impression coping: : 4.1 mm L=18.50 mm A=11 mm - Aesthetic non-hex impression coping: : 6.0 mm L=18.50 mm A=11 mm - Long non-hex impression coping: : 4.1 mm L=21.50 mm A=14 mm - Maximum tightening torque 10 Ncm.

35 Prostheses. Prosthetic System MG-InHex Maxi MG-InHex Prosthetic System MAXI MG-INHEX IMPLANT ANALOG MAXI MG-INHEX Implant Analog MG-INHEX MAXI Analog wrench MG-INHEX MAXI - Stainless Steel - Platform: 3.80 mm - : 5.00 mm - One single use Analog wrench To hold the abutment or crown for a comfortable handling at lab or clinic MAXI MG-INHEX TITANIUM UCLA MAXI MG-INHEX TITANIUM Non-Hex Titanium UCLA w/s for MG-INHEX MAXI - Titanium Grade V abutment - Attaches directly to implant - For cement retained or screwretained restorations - Platform: 3.80 mm - : 4 mm - Screwdriver: 1.25 mm Hex Hex Titanium UCLA w/s MG-INHEX MAXI A= 10 mm - Hex abutment is recommended for unitary restorations - Recommended Torque 30 Ncm. - Ensures a correct fit of the abutment to the implant GOLD Hex GOLD BASE UCLA w/s for MG-INHEX MAXI (Gold 60/19) Non-Hex GOLD BASE UCLA w/s for MG-INHEX MAXI (Gold 60/19) A= 10 mm A= 2,7 mm - Castable UCLA with Gold Base abutment - Attaches directly to implant - Platform: 3.80 mm - : 4 mm - Screwdriver: 1.25 mm Hex. - Cast with 60/19 Gold alloys. - Melting temperature 1415ºC * Abutments are also available without screw. * Hex castable abutments are red-coloured for an easy identification. - Recommended Torque 30 Ncm. - Ensures a correct fit of the abutment to the implant ABUTMENT FOR ZIRCONIUM Abutment for Zirconium w/s MG-INHEX MAXI Includes one Sirona s CEREC 3D scanbody 0, Scanbodies (3 pcs each pack)* Compatible with Sirona s CEREC 3D TITANIUM BASE FOR CAD/CAM. For production of customized mesostructures by CAD/CAM techniques Mozo-Grau abutment for Zirconium allows the professional to carry out customized restorations using Zirconium over Mozo-Grau implants with the highest possible accuracy. The abutment for Zirconium can be used as base to cement zirconium structures or mesostructures for unitary or multiple restoration cases, achieving the best possible passive adjustment that allows a safe, predictable and aesthetic result. Mozo-Grau abutment for Zirconium can be scanned by some of the best scanners currently in the market allowing the use of modern software for infographic design. p. 35

36 Prostheses. Prosthetic System MG-InHex Maxi MG-InHex Prosthetic System MAXI MG-INHEX HEX PREPABLE ABUTMENT MAXI MG-INHEX Hex Prep. Abut. w/s for MG-INHEX MAXI Hex Prep. Abut. w/s for MG-INHEX MAXI Hex Prep. Abut. w/s for MG-INHEX MAXI CUFF HEIGHT (H) 0 mm 1 mm 2 mm 6,5 mm H - Titanium Grade V - Attaches directly to implant - For cement retained or screwretained restorations - Platform: 3.80 mm - : 4.1 mm - Screwdriver: 1.25 mm Hex Hex Prep. Abut. w/s for MG-INHEX MAXI Hex Prep. Abut. w/s for MG-INHEX MAXI 4 mm - Hex abutment is recommended for unitary restorations - Torque 30 Ncm. * Abutments are also available without screw. MAXI MG-INHEX NON-HEX PREPABLE ABUTMENT Non-Hex Prep. Abut. for MG-INHEX MAXI Non-Hex Prep. Abut. for MG-INHEX MAXI Non-Hex Prep. Abut. for MG-INHEX MAXI Non-Hex Prep. Abut. for MG-INHEX MAXI Non-Hex Prep. Abut. w/s for MG-INHEX MAXI Non-Hex Prep. Abut. w/s for MG-INHEX MAXI Non-Hex Prep. Abut. w/s for MG-INHEX MAXI Non-Hex Prep. Abut. w/s for MG-INHEX MAXI CUFF HEIGHT (H) 1 mm 2 mm 4 mm 1 mm 2 mm 4 mm * Abutments are also available without screw. MAXI MG-INHEX AESTHETIC HEX PREPABLE ABUTMENT Aest. Hex Prep. Abut. w/s for MG-INHEX MAXI Aest. Hex Prep. Abut. w/s for MG-INHEX MAXI CUFF HEIGHT (H) 4 mm * Abutments are also available without screw. 6,5 mm H 6,5 mm H 6,5 mm H MAXI MG-INHEX - Titanium Grade V abutment for chair side modification - Attaches directly to implant - For multiple restorations - For cement retained restorations. - Platform: 3.80 mm - : 4.1 mm - Screwdriver: 1.25 mm Hex. - Soft tissue height must be above the abutment ring height - Torque 30 Ncm. MAXI MG-INHEX - Titanium Grade V post for chair side modification - Attaches directly to implant - For single or multiple restorations - For cement retained restorations - Platform: 3.80 mm - : 6.0 mm - Screwdriver: 1.25 mm Hex - Soft tissue height must be above the abutment ring height - Usable in situations of high aesthetic compromise - Torque 30 Ncm. p. 36 [ Hex ] [ Hex ] [ 2 pieces ] [ Non Hex ]

37 Prostheses. Prosthetic System MG-InHex Maxi MG-InHex Prosthetic System MAXI MG-INHEX ANGLED PREPABLE ABUTMENT MAXI MG-INHEX º Angled prep. abut. w/s for MG-INHEX MAXI 15º Angled prep. abut. w/s for MG-INHEX MAXI 15º Angled prep. abut. w/s for MG-INHEX MAXI 20º Angled prep. abut. w/s for MG-INHEX MAXI 20º Angled prep. abut. w/s for MG-INHEX MAXI 20º Angled prep. abut. w/s for MG-INHEX MAXI CUFF HEIGHT (H) 1 mm 5 mm 1 mm 5 mm MAXI MG-INHEX LOCATOR ABUTMENT Locator Analog pack 2 pcs. CUFF HEIGHT (H) Locator Abut. and processing package MG-INHEX MAXI Locator Abut. and processing package MG-INHEX MAXI Locator Abut. and processing package MG-INHEX MAXI Locator Abut. and processing package MG-INHEX MAXI Locator Abut. and processing package MG-INHEX MAXI mm 4 mm 5 mm 5 mm 6,5 mm H H 4 mm - Titanium Grade V abutment for chair side modification - Attaches directly to implant - For single or multiple restorations - For cement retained restorations - Used to correct disparallelism - Platform: 3.80 mm - : 4.0 mm - Screwdriver: 1.25 mm Hex - Soft tissue height must be above the abutment ring height - Torque 30 Ncm. MAXI MG-INHEX - For overdentures - Accommodates a divergent implant between 10 and 20 degrees (40 degrees between implants) - Attaches directly to the implant - Platform: 2.80 mm - : 4.0 mm - Use Locator Core Tool - Torque 20 Ncm - It is convenient to leave the Locator abutment at least 1 mm above the soft-tissue level - The use of the Paralleling Guide will help to avoid problems when placing the abutments Locator impression coping Pack 4 units. Locator bar attachment processing pack Locator bar attachment 2mm (2 pack) * Males Clear=strong / Pink=light / Blue=Extralight * Males for divergent implants Green=strong / Red=light p. 37 [ Non Hex ] [ Non Hex ] [ Hex ] MAXI MG-INHEX BALL ABUTMENT Ball Abut. with Plastic cap for MG-INHEX MAXI Ball Abut. with Plastic cap for MG-INHEX MAXI Ball Abut. with Plastic cap for MG-INHEX MAXI Ball Abut. with Plastic cap for MG-INHEX MAXI Ball Abut. with Plastic cap for MG-INHEX MAXI Ball Abutlment Analog (stainless steel) Plastic Cap CUFF HEIGHT (H) 1 mm 2 mm 4 mm 5.5 mm MAXI MG-INHEX - For overdentures - Maximum angle of 10º - Attaches directly to the implant - Platform: 3.80 mm - : 4.0 mm - Screwdriver: 1.25 mm Hex. - Stainless steel - Torque 30 Ncm - It is convenient to leave the cuff 1 mm above the soft tissue - The use of the Paralleling Guide will help to avoid disparalellism problems when placing the ball abutments

38 Prostheses. Prosthetic System MG-InHex Maxi MG-InHex Prosthetic System Transmucosal tapered abutment for screw retained restorations Recommended for immediate loading and compromised cases with damaged periodontal tissues. Eases the exchange of provisional abutments during the immediate loading protocol. Improves the emergency profile and maintains the gingival and osseous level. Avoids the contact of the temporary abutments and impression copings with the wound. Protects the hard and soft perimplantary tissues and eases the prosthetics hygiene. MAXI MG-INHEX TAPERED ABUTMENTS MAXI MG-INHEX CUFF HEIGHT (H) º tapered abutment MG-INHEX MAXI 10º tapered abutment MG-INHEX MAXI 10º tapered abutment MG-INHEX MAXI 10º tapered abutment MG-INHEX MAXI 10º tapered abutment MG-INHEX MAXI 10º tapered abutment MG-INHEX MAXI 30º tapered abutment MG-INHEX MAXI 30º tapered abutment MG-INHEX MAXI 0 mm 1 mm 2 mm 4 mm 5 mm 1 mm 2 mm Flat side that provides an anti-rotational system to the abutment. 2 mm H 0,75 mm H - For multiple restorations - For overdentures or superstructures - For screw-retained restorations - The10º or 30º angle corrects disparallelism - Attaches directly to the implant - Platform: 3.80 mm - : 4.0 mm - Screwdriver: 1.25 mm Hex. - For restorations in soft tissues thicker than - To take impressions is recommendable to use tapered abutments impression copings - Torque 30 Ncm º tapered abutment MG-INHEX MAXI º tapered abutment MG-INHEX MAXI 4 mm º tapered abutment MG-INHEX MAXI 5 mm p. 38

39 Prostheses. Prosthetic System MG-InHex Maxi MG-InHex Prosthetic System MAXI MG-INHEX TAPERED ABUTMENTS MAXI MG-INHEX º anti-rotational castable post for tapered abut. w/s - Castable abutment. - Torque 20 Ncm º rotational castable post for tapered abut. w/s 30º rotational castable post for tapered abut. w/s 11 mm * Anti-rotational castable abutments are manufactured in red colour for an easy identification º anti-rotational titanium post for tapered abut. w/s - Grade V Titanium. - Torque 20 Ncm º rotational titanium post for tapered abut. w/s 30º rotational titanium post for tapered abut. w/s 11 mm * Anti-rotational titanium abutments are manufactured in purple colour for an easy identification º tapered abutment analog - Material: stainless steel º tapered abutment analog / / 30 10º anti-rotational impression coping for tapered abut. w/s 10º / 30º rotational impr. coping for tapered abut. w/s 10º / 30º impression coping for tap. abut. closed tray 11 mm * Anti-rotational abutments are manufactured in purple colour for an easy identification º tapered abutment cap (1 piece) 4,2 mm - Grade V Titanium º tapered abutment cap (1 piece) º angled tapered abutment MG-INHEX MAXI 2 mm height - Grade V Titanium. - Torque 30 Ncm º angled tapered abutment MG-INHEX MAXI height 17º angled tapered abutment MG-INHEX MAXI 4 mm height - Used to correct disparalellism between implants. - Used to restore implants with very divergent emergency angles Rotational castable post for 17º angled tapered abutment w/s - Castable abutment. - Torque 20 Ncm Rotational titanium post for 17º angled tapered abutment w/s - Grade V Titanium. - Torque 20 Ncm Rotational 17º angled tapered abutment analog w/s - Material: stainless steel Rotational impression coping for 17º angled tapered abutment w/s - Material: stainless steel º tapered abutment cap - Grade V Titanium. p. 39

40 Prostheses. Prosthetic System MG-InHex Temporary Prostheses/Immediate Loading MG-InHex 2 MM HEIGHT MG-INHEX TEMPORARY PREPABLE ABUTMENT MG-INHEX [ Hex ] [ Hex ] [ Hex ] [ Non Hex ] [ Non Hex ] CUFF HEIGHT (H) 2 mm 2 mm 2 mm 2 mm 2 mm MG-INHEX TEMPORARY TITANIUM UCLA ABUTMENT Temp. Prep. Abut. Hex for chair side modif. MG-INHEX MINI w/s Temp. Prep. Abut. Hex for chair side modif. MG-INHEX STD w/s Temp. Prep. Abut. Hex for chair side modif. MG-INHEX MAXI w/s Temp. Prep. Abut. Non-Hex for chair side modif. MG-INHEX STD w/s Temp. Prep. Abut. Non-Hex for chair side modif. MG-INHEX MAXI w/s MG-INHEX TEMPORARY CASTABLE UCLA ABUTMENT Temporary castable non hex UCLA MG-INHEX STD w/s Temporary castable non hex UCLA MG-INHEX MAXI w/s Temporary castable hex UCLA MG-INHEX STD w/s Temporary castable hex UCLA MG-INHEX MAXI w/s * Abutments are also available without screw. * Anti-rotational castable abutments are manufactured in red colour for an easy identification. Temporary titanium Hex UCLA for MG-INHEX STD w/s Temporary titanium Hex UCLA for MG-INHEX MAXI w/s A= 10 mm 10 mm - Titanium Grade V abutment for chair side modification - Attaches directly to implant - For single or multiple restorations - Screw retained - Screwdriver: 1.25 mm Hex - Retaining Surface - Easy fixation of the temporary prosthesis - MINI: 2. - STD: 2.8 mm - MAXI: 3.8 mm - For temporary restorations to be placed for up to 2 or 3 months - Torque 10 Ncm * Plastic cap included, except on MG-Inhex MINI. To place between the temporary crown and the abutment to ensure a better fit * Abutments are also available without screw Plastic cap Facilitates and ensures a correct passive adjustment of the aesthetic temporary crown. MG-INHEX - Temporary castable abutment - For direct to implant restorations - For screw retained restorations - Platform STD: 2.80 mm - Platform MAXI: 3.80 mm - : 4 mm - Screw driver: 1.25 mm hex - For unitary restorations is recommended to use hex abutments - Torque 10 Ncm MG-INHEX - Titanium Grade V abutment for chair side modification - Attaches directly to implant - Screw retained - Screwdriver: 1.25 mm Hex - Retaining Surface - Easy fixation of the temporary prosthesis Temporary titanium Non-hex UCLA for MG-INHEX STD w/s Temporary titanium Non-hex UCLA for MG-INHEX MAXI w/s - For temporary restorations to be placed for up to 2 or 3 months - Torque 10 Ncm. *Abutments are also available without screw p. 40 7,6 mm 6,5 mm H [ Non Hex ]

41 Prostheses. Prosthetic System MG-InHex Temporary Prostheses/Immediate Loading MG-InHex TEMPORARY CASTABLE POST FOR TAPERED ABUTMENT MG-INHEX [ Non Hex ] Temporary castable post for 10º tapered abut. w/s - Abutment for chair side modification - Screwdriver: 1.25 mm Hex. - Screw retained - Retaining Surface - Easy fixation of the temporary prosthesis Temporary castable post for 30º tapered abut. w/s 11 mm - For temporary restorations to be placed for up to 2 or 3 months - Torque 10 Ncm. TEMPORARY TITANIUM POST FOR TAPERED ABUTMENT MG-INHEX [ Non Hex ] Temporary Titanium post for 10º Tapered Abut. w/s Temporary Titanium post for 30º Tapered abut. w/s 11 mm - Abutment for chair side modification - Screwdriver: 1.25 mm Hex. - Screw retained - Retaining Surface - Easy fixation of the temporary prosthesis - For temporary restorations to be placed for up to 2 or 3 months - Torque 10 Ncm. Temporary post for tapered abutment Allows the retention of the temporary prosthesis during the immediate loading procedure. TEMPORARY TITANIUM POST FOR ANGLED TAPERED ABUTMENT MG-INHEX [ No Hex ] Temporary Titanium post for 17º angled tapered abutment - Abutment for chair side modification - Screwdriver: 1.25 mm Hex. - Screw retained - Retaining Surface - Easy fixation of the temporary prosthesis - For temporary restorations to be placed for up to 2 or 3 months - Torque 10 Ncm. TEMPORARY CASTABLE POST FOR ANGLED TAPERED ABUTMENT MG-INHEX - Abutment for chair side modification - Screwdriver: 1.25 mm Hex. - Screw retained - Retaining Surface - Easy fixation of the temporary prosthesis - For temporary restorations to be placed for up to 2 or 3 months - Torque 10 Ncm. p. 41 [ No Hex ] Temporary Castable post for 17º angled tapered abutment

42 Prostheses. Prosthetic System MG-InHex Temporary Prostheses/Immediate Loading MG-InHex RETAINING CAP FOR TAPERED ABUTMENT MG-INHEX [ Non Hex ] Retaining cap for 10º tapered abutment with screw 6 mm - Screw retained. - Screw driver: 1.25 mm hex. - Retaining surface. - Easy fixation of the temporary prosthesis Retaining cap for 30º tapered abutment with screw - For temporary restorations to be placed for up to 2 or 3 months - Torque 10 Ncm. Retaining cap for tapered abutment Allows the adaptation of the patient s temporary prosthesis during the immediate loading procedure. p. 42

43 Prostheses. Prosthetic System MG-InHex Screws for abutments and transfers MINI MG-INHEX IMPLANT MG-INHEX DESCRIPCIÓN Short transfer screw L=17 mm A=9 mm MG-INHEX MINI Long transfer screw L=2 A=17 mm MG-INHEX MINI Transfer screw for waxing MG-INHEX MINI head=2.1 mm thread= 1.4. L=29 mm A=2 Retaining screw hex mm L= 8.6 mm MG-INHEX MINI Retaining screw for angled abutment L= 8.20 mm MG-INHEX MINI [ MINI ] - head: 2.1 mm thread: 1.4 mm [ STANDARD ] - head: 2.4 mm thread: 1.6 mm [ MAXI ] - head: 2.4 mm thread: 2.0 mm STANDARD MG-INHEX IMPLANT A L A L A L A L A Short transfer screw L=14 mm A=8 mm MG-INHEX STD L Long transfer Screw L=20 mm A=14 mm MG-INHEX STD Transfer screw for waxing L=26 mm A=20 mm MG-INHEX STD Retaining screw Hex 1.25 mm L=7.7 mm A=1.7 mm MG-INHEX STD Ret. screw w/slot for dif. sit. L=6.9 mm A=1.2 mm MG-INHEX STD Ret. screw for ang. abut. L=6.9 mm A=1.2 mm MG-INHEX STD Prosthetic screw for castable/titanium tapered abutment L=4.7 mm A=1.7 mm MG-OSSEOUS/INHEX STD MG-INHEX Lab Screw - Head: 2.4 mm Thread: 1.6 mm A=2.3 mm L=8.4 mm MAXI MG-INHEX Lab Screw - Head: 2.4 mm Thread: 2.0 mm A=2.3 mm L=9.7 mm Retaining screw for 17º angled tapered abut. MG-INHEX STD Prosth. screw for 17º angled tap. abut. MG-OSSEOUS/INHEX Lab screw MG-INHEX STD (5 pcs) A L MAXI MG-INHEX IMPLANT Short transfer screw L=14 mm A=8 mm MG-INHEX MAXI Long transfer Screw L=20 mm A=14 mm MG-INHEX MAXI Transfer screw for waxing L=26 mm A=20 mm MG-INHEX MAXI Ret. screw Hex 1.25 mm L=7.7 mm A=1.7 mm MG-INHEX MAXI Ret. screw w/slot for dif. sit. L=6.9 mm A=1.2 mm MG-INHEX MAXI Ret. screw for angled abut. L=6.9 mm A=1.2 mm MG-INHEX MAXI Prosthetic screw for castable/titanium tapered abutment L=4.7 mm A=1.7 mm MG-OSSEOUS/INHEX Retaining screw for 17º angled tapered abutment MG-INHEX MAXI Prost. screw for 17º angled tapered abutment MG-OSSEOUS/INHEX Lab screw MG-INHEX MAXI (5 pcs) p. 43

44 Surgical kit for Computer-Guided Surgery Fidelis MG-Fidelis

45 Surgical material

46 Surgical material. Instructions for maintenance Instructions for maintenance of surgical instruments PRE-TREATMENT All products must be cleaned, disinfected and sterilized prior to use; this applies in particular prior to first use i.e. after delivery as all products are supplied nonsterile. The thorough cleaning and disinfecting is indispensable in order to achieve effective sterilization. The disinfectant used during pre-treatment only ensures personal protection and can be no substitute for the disinfection procedure to be used later after completion of the cleaning process. TREATMENT DURING USE During use, separate the soiled instruments to avoid further contamination of the instrument tray. Clean / disinfect the soiled products, arrange them in the instrument tray, and sterilize only the instruments that will be used. Impurities must be removed from the products directly after use. To do so, use distilled water or a disinfectant solution; the disinfectant must not contain aldehyde (which could fix blood residues to the instrument surface). TREATMENT AFTER USE 1. Choosing the cleaning / disinfecting agents: It is recommended to use a neutral/enzymatic detergent (minimum admissible ph value 5.5). It should contain neither bleach nor Organic solutions (e.g. alcohols, ether), nor oxidants (e.g. hydrogen peroxides), nor halogens (chlorine, iodine, bromine). Caution should be paid with tap water as it may contain too much chlorine. Avoid solutions with aldehyde (which could fix blood residues to the instrument surface). 2. Choosing the products for the cleaning process: For the manual removal of impurities, only use nylon brushes. Never use metal brushes or steel wool. Use a wire to clean the internal cooling canal of the drills (Not applicable to RCD drills). 3. How to clean / disinfect the surgical instruments: Eliminate thoroughly all the post-operative residues (blood, bone...). As to products with lumen (cavities), such as drills with internal cooling, rinse all cavities by using a disposable syringe and a wire for this purpose (Not applicable to RCD drills). Do not clean, implant drills with other tools made of different material, in the same ultrasonic box. During the cleaning process in ultrasonic box, avoid as much as possible, shocks and contacts with other drills or instruments. Rinse and dry the drills immediately after the cleaning process (preferably use distilled water to rinse). Never store instruments while they are still wet. 4. How to sterilize: Sterilization by wet heat autoclaving 134 ºC (273 ºF) - 18 minutes (5 minutes in case of RCD drills). Make sure that the elements, inside the autoclave, are not rusted. Wrap the elements in sterilization packaging intended for this purpose. Never allow surgical instruments to touch one another while being sterilized. Surgical instruments and sterilization trays should never be exposed to temperatures exceeding 137 C (279 F). p. 46

47 Surgical material. Surgical kits Surgical kits MG-INHEX SURGICAL KIT Locator drill 2.0 mm twist drill Conical drills: 3.0 / 3.3 / 3.8 / 4.3 / 4.7 mm Profile drills: 3.3 / 3.7 / 4.2 / 4.95 mm Conical drills for hard bones: 3.2 / 3.5 / 4.0 / 4.9 mm 1.25 mm long hex screwdriver Paralleling pins: 4.1 / 5.0 mm 16 mm ratchet wrench extender 15 mm drill extender STD MG-INHEX depth gauge MAXI MG-INHEX 20 mm long implant mount STD MG-INHEX 20 mm long implant mount Hexed hand wrench Ratchet wrench with Hex. converter Open-end wrench Surgical kit box C/A implant mount driver MG-INHEX PLUS SURGICAL KIT Locator drill 2.0 mm twist drill. 3.0 mm conical drill. 3. conical drill 3.8 mm conical drill 4. conical drill 3. profile drill 4.7 mm conical drill 3.75 mm profile drill 3.2 mm conical drill. Hard bone 4.25 mm profile drill MAXI MG-INHEX long implant mount 3.5 mm conical drill. Hard bone 5.0 mm profile drill 4.0 mm C/A circular tissue punch 4.0 mm conical drill. Hard bone 3. bone tap 5.0 mm C/A circular tissue punch 4.9 mm conical drill. Hard bone 3.75 mm bone tap Drill extender 2.0 mm long twist drill mm bone tap 9 mm ratchet wrench extender 3.0 mm long conical drill. 5.0 mm bone tap 16 mm ratchet wrench extender 1.25 mm long hex screwdriver 3. long conical drill Paralleling pins (2 units) C/A Implant mount driver 1.25 mm short C/A hex screwdriver 3.8 mm long conical drill STD MG-INHEX depth gauge Ratchet wrench with Hex converter 1.25 mm long C/A hex screwdriver 4. long conical drill MAXI MG-INHEX depth gauge Open-end wrench Plus surgical kit box 4.7 mm long conical drill STD MG-INHEX long implant mount 1.25 mm short hex screwdriver p. 47

48 Surgical material. Drills for implants Drills for implants LOCATOR DRILLS ø LENGTH DEPTH MARKING mm 8 mm mm mm 16 mm mm 16 mm 6 mm new rdc 2.0 mm 16 mm mm 21 mm - Material: Stainless steel - Internal irrigation - Locator drill depth marks: 8-9 mm mm drills depth marks: mm - 6-mm depth mark drill depth marks: mm mm Long drills depth marks: mm - Use and sterilise the drills up to 3 surgeries (RCD Drills 5 surgeries) - Sterilise only the drills used in the surgery RCD STRAIGHT CONICAL DRILLS ø LENGTH new 3,0 mm 16 mm new 3, 16mm new 3,8 mm 16mm new 4, 16mm - Color ring - Drills lenght: 16 mm - Material: Stainless steel, Diamong-Like Carbon coated - No internal irrigation - Depth marks: mm - Use and sterilise the drills up to 5 surgeries - Sterilize only the drills used in the surgery new 4,7 mm 16mm STRAIGHT CONICAL DRILLS ø LENGTH mm mm mm 3.0 mm mm 16 mm 16 mm 16 mm 16 mm 16 mm 20 mm 20 mm 20 mm - Color ring - Long drills lenght: 20 mm - Short drills length: 16 mm - Material: Stainless steel - Internal irrigation - Short drills depth marks: mm - Long drills depth marks: mm - Use and sterilise the drills up to 3 surgeries - Sterilise only the drills used in the surgery mm mm 20 mm p. 48

49 Surgical material. Drills for implants Drills for implants STRAIGHT CONICAL DRILLS WITH 6 MM DEPTH MARK Ref. Short straight conical drill 3.0 mm - 6 mm depth mark Short straight conical drill mm depth mark Short straight conical drill 3.8 mm - 6 mm depth mark Short straight conical drill mm depth mark Short straight conical drill 4.7 mm - 6 mm depth mark - Color ring - Drills lenght: 16 mm - Material: Stainless steel - Internal irrigation - Depth marks: mm - 3 uses - Sterilize only the drills used in the surgery RCD STRAIGHT CONICAL DRILLS FOR HARD BONE ø LENGTH new 3,2 mm 16 mm new 3,5 mm 16mm new 4,0 mm 16mm new 4,9 mm 16mm - Double color ring - Drills lenght: 16 mm - Material: Stainless steel, Diamong-Like Carbon coated - No internal irrigation - Depth marks: mm - 5 uses - Sterilize only the drills used in the surgery STRAIGHT CONICAL DRILLS FOR HARD BONE ø 3.2 mm 3.5 mm 4.0 mm 4.9 mm LENGTH 16 mm 16 mm 16 mm 16 mm - Double color ring - Short drills lenght: 16 mm - Material: Stainless steel - Internal Irrigation - Short drills depth marks: mm - Use and sterilise the drills up to 3 surgeries - Sterilise only the drills used in the surgery p. 49

50 Surgical material. Drills for implants Drills for implants PROFILE DRILLS Profile drill 3. MG-INHEX Profile drill 3.75 mm MG-INHEX Profile drill 4.25 mm MG-INHEX Profile drill 5.0 mm MG-INHEX - Material: Stainless steel - Sterilise only the drills used in the surgery BONE TAPS Bone tap 3.3 / 3.40 mm MG-OSSEOUS/INHEX Bone tap 3.75 mm MG-OSSEOUS/INHEX Bone tap 4.25 mm MG-OSSEOUS/INHEX Bone tap: 5.0 mm MG-OSSEOUS/INHEX - Material: Stainless steel - Depth marks: mm Recommendations: - Drill speed: 15 rpm RCD DRILL STOP KIT new DRILL STOP KIT This kit includes 21 drill stops to place implants (from 6 mm to 15 mm long) with RCD (Diamond-like carbon) drills - Sterilizable material - Delivers stop easy pick-up and release. - Stop color-coding and organization in the box aid in easy identification. - Reduced size to facilitate storage and sterilization. - Measurement guide aid to ensure a safe drilling process. - Depth identification for each stop group (A, B or C). This kit is composed of all the stop range for Mozo Grau RCD (Diamondlike carbon) drills Instructions for use: 1. Insert the drill into the contra-angle and select the appropriate drill stop according to the desired drillings depth. 2. Insert the drill to the end of drill stop. 3. Verify drilling depth by using the drill depth guide. 4. To release the stop from the drill, insert the contra-angle in the appropriate metallic sheet and pull up. The stop will fall safely into the box. p. 50

51 Surgical material. Surgical Wrenches Surgical material LONG IMPLANT MOUNTS Long implant mount 20 mm INHEX MINI Long implant mount 20 mm INHEX STD Long implant mount 20 mm INHEX MAXI - Replace the normal implant mount in difficult situations (limited interdental space available). - Millimeter marks: useful on flapless surgeries SURGICAL WRENCHES DESCRIPCIÓN Open-end wrench Ratchet wrench Dynamometrical ratchet wrench 45 Ncm. Multiconverter for C/A latch Hexed dynamometrical ratchet wrench adapter Hexed hand wrench Open-end wrench - To hold the implant mount while it is unscrewed. Suitable for cases with little primary stability. Ratchet wrench: - To insert implant - To insert non-traumatic bone expanders Dynamometrical ratchet wrench - To ensure a proper implant insertion torque Multiconverter for C/A latch - To be used with C/A tissue punches and C/A screwdrivers Hexed dynamometrical ratchet wrench - To insert implant with the dynamometrical ratchet wrench Hand wrench - To insert implant by hand p. 51

52 Surgical material. Surgical Wrenches Surgical material RATCHET WRENCH AND DRILL EXTENDERS Ratchet wrench extender 9 mm Ratchet wrench extender 16 mm Drill extender 15 mm - To be used when limited interdental space is available. - To be used when adjacent teeth height does not allow C/A a proper drilling. - In some cases, to be used to replace long drills. C/A IMPLANT MOUNT DRIVER AND CONVERTER C/A implant mount driver Square to Hexagon converter for Ratchet wrench - To insert implants with C/A DEPTH GAUGES mm depth gauge. MINI MG-INHEX mm depth gauge. STD MG-INHEX mm depth gauge. MAXI MG-INHEX 2.0 mm angled depth gauge - Material: stainless steel - D epth marks: , mm. PARALLELING PIN Paralleling pin for MINI platform Paralleling pin for STD platform Paralleling pin for MAXI platform - To ensure implant parallelism at the beginning of the surgery - The pin ring matches the implant platform p. 52

53 Advanced surgery. Bone expansion Bone expansion NON-TRAUMATIC MG-EXPANDERS SET Non-traumatic MG-Expanders set. Size pattern and hand wrench included Hand wrench for MG-Expanders - An easy system for bone expansion or pressing which allows a measured and progessive control. Indicated for thin crests or type IV bone crests (pressing). It allows a perfect control of the implants insertion axis. - Surgical technique: The expanders should be introduced following a slow and sequential method. Once an excessive resistance is encountered, the insertion should be stopped for a few seconds to avoid heating and, then, continue with the normal insertion sequence until the desired depth is reached. The size pattern will help to identify the exact width of each expander according to their depth markings. - Recommended for thin crests or to compact bone in crest where Tipe IV bones are present. Recommendable only for upper maxilla Upper maxilla bone expansion with MG-Expanders p. 53