VISION 350 HOME GYM. HOME GYM ASSEMBLY, CARE AND INSTRUCTION MANUAL FITNESS #1 HOME

Transcription

1 TROJAN MY SPACE MY TIME VISION 350 HOME GYM HOME GYM ASSEMBLY, CARE AND INSTRUCTION MANUAL CAUTION READ ALL PRECAUTIONS AND INSTRUCTIONS IN THIS MANUAL BEFORE USING THIS EQUIPMENT KEEP THIS MANUAL FOR FUTURE REFERENCE WARRANTY TROJAN #1 HOME SOUTH AFRICA S FITNESS SINCE

2 INDEX PAGE 1. SAFETY INSTRUCTIONS 3 2. PRE ASSEMBLY CHECK LIST 5 3. HARDWARE LIST 6 4. PARTS LIST 9 5. ASSEMBLY STEPS FITNESS TIPS & TECHNIQUES CONDITIONING GUIDELINES WARM - UP AND COOL-DOWN EXERCISE PROGRAM FREQUENTLY ASKED QUESTIONS EXPLODED DRAWING TROJAN 1 YEAR LIMITED WARRANTY TROJAN REPAIRS PROCEEDURE

3 1. SAFETY INSTRUCTIONS It is the sole responsibility of the purchaser of TROJAN products to read the owner s manual, warning labels and instruct all individuals, on proper usage of the equipment. Understanding each and every warning to the fullest is important. If any of these instructions or warnings are unclear please contact Trojan Customer Services on (0861 Trojan), within the Republic of South Africa. The equipment is only intended for HOME USE and is NOT INTENDED FOR COMMERCIAL, INSTITUTIONAL AND/OR STUDIO FACILITIES USE. Contact TROJAN with any questions regarding this classification. It is recommended that all users of TROJAN be informed of the following information prior to use. HEALTH WARNING Before starting any exercise or conditioning program you should consult with your personal physician to see if you require a complete physical exam. This is especially important if you are over the age of 35 or have never exercised, are pregnant or suffer from any illness. If at any time during exercise you feel faint, dizzy or experience pain, stop exercising immediately and consult your physician. To avoid muscular pain and strain, begin each workout by stretching and warming up and end each session by cooling down and stretching. ACCESS CONTROL TROJAN recommends that all fitness equipment be used in a supervised area. It is recommended that the equipment be located in an access controlled area. Control is the responsibility of the owner. Keep children away from all equipment. Parents or others supervising adults must provide close supervision of children if the equipment is used in the presence of children. INSTALLATION TROJAN recommends that all equipment: Be secured to or set up on a solid, level surface to stabilize and eliminate rocking or tipping over during training. Be set up inside your home away from moisture and dust (the equipment is not designed for outdoor use). Be set up with sufficient ventilation to ensure proper operation. Be set up with sufficient space around the equipment so that all exercises can be completed safely. It is recommended that there should be at least 1m of space around the equipment where access is required to exercise. For treadmills it is recommended that you have 2m of space behind the running deck. Be installed by our team of installers. PROPER USAGE Do not use the equipment in any way other than as designed or intended by the manufacturer. It is imperative that TROJAN equipment is used properly to avoid injury. Injuries may result from exercising improperly or excessively. Your TROJAN equipment should only be used by one person at a time. Be careful to maintain your balance while using, mounting, dismounting, folding, unfolding or assembling your TROJAN equipment to avoid injury. Do not attempt to adjust any seats / pads / pulleys etc. while you are on your TROJAN equipment. Servicing other than the procedures in this manual should be performed by an authorized service representative only. Gym and Benches - When adjusting any seat, knee hold down pad, range of motion limiter, foothold pad, pulley or any other type of adjuster, make certain the adjusting pin is fully engaged in the hole to avoid injury

4 1. SAFETY INSTRUCTIONS INSPECTION Do not use or permit use of any equipment that is damaged or has worn or broken parts. For all TROJAN equipment use only replacement parts supplied by TROJAN. Always make sure that all nuts and bolts are tightened prior to each use. Cables and belts pose an extreme liability if used when frayed. Always replace any cable at first sign of wear. Routinely inspect all accessory clips that join attachments to the cables and replace at the first sign of wear. Maintain labels and nameplates do not remove labels for any reason. They contain important information. Equipment maintenance Preventative maintenance is the key to smooth operating equipment. Please ensure that you follow our maintenance tips to ensure the continued correct function of your TROJAN equipment. Before any use, examine all accessories approved for use with the TROJAN equipment for damage or wear. Should your Trojan equipment appear damaged or worn do not attempt to use or repair the equipment yourself. Please contact our service department on (0861 Trojan) to arrange a repair. OPERATING WARNINGS It is the purchaser s responsibility to instruct all users as to the proper operating procedures of all TROJAN equipment. Keep children away from all moving parts and away from all strength equipment. Parents must provide close supervision of children if the equipment is used in the presence of children. Do not wear loose fitting clothing or jewellery when using the equipment. It is also recommended that users tie up long hair to avoid contact with moving parts. Ensure that anyone not using the equipment stays clear of the user, accessories and moving parts while the machine is in operation. SELECTORIZED WEIGHT STACKS Use only weight selector pins supplied by TROJAN. Should you loose or damage your pin, contact our service department to arrange delivery of a new pin. Ensure that weight selector pins are fully inserted as partial insertion can cause weights to fall unexpectedly. Never pin the weight stack in an elevated position. Never remove a selector pin if any weights are suspended. Never attempt to release jammed weights or pins that are suspended. USER WEIGHT LIMITATIONS This TROJAN VISION 350 may not be used by persons weighing more than 120kg. SAVE THIS INSTRUCTION MANUAL FOR FUTURE USE AND REFERENCE If any of these instructions or warnings are unclear please contact Trojan Customer Services on (0861 Trojan), within the Republic of South Africa or visit

5 2. PRE ASSEMBLY CHECK LIST Thank you for choosing the TROJAN VISION 350 HOME GYM. We take great pride in producing this quality product and hope it will provide many hours of quality exercise to make you feel better, look better and enjoy life to its fullest. Yes, it is a proven fact that a regular exercise program can improve your physical and mental health. Too often, our busy lifestyles limit our time and opportunity to exercise. The TROJAN VISION 350 HOME GYM provides a convenient and simple method to begin your assault on getting your body in shape and achieving a healthier lifestyle. Before reading further, please familiarise yourself with the parts that are labelled. Read this manual carefully before using the TROJAN VISION 350 HOME GYM. Lat Bar Pulley Back Rest Cushion Guide Rod Butterfly Arm Seat Cushion Arm Curl Attachment Weight Stack Leg Curl Pad Chest Press Arm Curl Bar

6 3. HARDWARE LIST

7 3. HARDWARE LIST

8 3. HARDWARE LIST

9 4. PARTS LIST NO. DESCRIPTION QTY 1 Main Base 1 2 Rear Base 1 3 Vertical Post 1 4 Guide Rod 2 5 Top Beam 1 6 Butterfly Extension 1 7 Left Butterfly Arm 1 8 Right Butterfly Arm 1 9 Seat Cushion Support 1 10 Seat Support Post 1 11 Leg Extension 1 12 Arm Curl Frame 1 13 Bench Press Arm 1 14 Solid Handle 2 15 Left Adjustable Plate 1 16 Right Adjustable Plate 1 17 Adjustable Press Frame (A) 1 18 Adjustable Press Frame (B) 1 19 Foam Rod (Short) 1 20 Foam Rod (Long) 1 21 Lat Bar 1 22 Curl Bar 1 23 Single Pulley Bracket 2 24 Pulley Bracket Plate 2 25 Intersect Pulley Bracket 1 NO. DESCRIPTION QTY 26 Arm Curl Cushion 1 27 Seat Cushion 1 28 Backrest Cushion 1 29 Weight Selection Rod 1 30 Top Plate 1 31 Weight Plate Weight Base Plate 1 33 Weight Selection Pin 1 34 Pin x 80mm Oval End Cap 2 36 Plastic Bushing x 50mm Square End Plug x 80mm Oval End Plug mm Round End Plug mm Round End Plug 5 41 Round Bushing 3 42 Bumper Cap /8 Plastic Dome Cap /8 Plastic Dome Cap /2 Plastic Dome Cap 2 46 Foam Roll 4 47 Round Bumper 2 48 Oval Bumper 2 49 PVC Handle Grip 4 50 Pop Pin

10 4. PARTS LIST NO. DESCRIPTION QTY 51 PT-1B Pop Pin 3 52 Chain Hook 5 53 Red Pulley 2 54 Pulley Big Pulley 1 56 Chain (Short) 1 57 Chain (Long) 1 58 Handle Grip (Long) 2 59 Handle Grip (Short) 2 60 Taper End Plug 1 61 Taper Bumper 1 62 Plate 2 63 Upper Cable 1 64 Low Cable 1 65 Butterfly Cable 1 66 Oil Bushing Ø 44 x Ø 39.4 x Ø 19.1 x 12mm Oil Bushing 4 68 Ø 50 x Ø 44 x Ø 12.8 x 12mm Oil Bushing 2 69 Ø 44 x Ø 39.4 x Ø 25.6 x 12mm Oil Bushing /8 x 3-3/8 Hex Bolt /8 x 4-1/4 Hex Bolt /8 x 2-1/2 Hex Bolt /8 x 1-1/2 Hex Bolt /8 x 2 Hex Bolt /8 x 2-1/8 Hex Bolt 2 NO. DESCRIPTION QTY 77 1/2 x 3-3/8 Hex Bolt /8 x 3-3/4 Hex Bolt /8 x 3 Hex Bolt 1 80 M10 x 25mm Screw 2 81 M8 x 16mm Hex Bolt 6 82 M8 x 42mm Hex Bolt 2 83 M8 x 60mm Hex Bolt 2 84 Ø 19 x 280 Pivot Shaft /8 Lock Nut /2 Lock Nut /8 Lock Nut 4 88 M8 Lock Nut 2 89 M8 Washer /8 Washer /2 Washer /8 Washer 4 93 T3.0 x Ø 11 x Ø 36mm Washer /8 x 4 Hex Bolt 2 95 T3.0 x Ø 13 x Ø 32mm Washer 1 96 T3.0 x Ø 26 x Ø 46mm Washer /8 x 3/4 Allen Bolt 2 98 Ø 13 x T1.0 x 11mm Bushing 2 99 Ø 13 x T1.0 x 17mm Bushing Ø 13 x T1.0 x 22mm Bushing /8 x 1-3/4 Hex Bolt /8 x 1 Hex Bolt

11 5. ASSEMBLY STEPS Step 1 Attach Main Base (1) to Rear Base (2) using two 3/8 x 4 Hex Bolts (94), four 3/8 Washers (90) and two 3/8 Lock Nuts (85)

12 5. ASSEMBLY STEPS Step 2 Slide one Round Bumper (47) onto each Guide Rod (4). Insert both Guide Rods (4) into the holes of Rear Base (2) using two 3/8 x1 Hex Bolts (76) and two 3/8 Washers (90) to secure them. Slide Weight Base Plate (32) down onto the Guide Rods (4) as shown. Attach the Plastic Bushing (36) onto the top of Weight Selection Rod (29), at the first hole, using Pin (34). Slide Top Plate (30) down as shown. Attach Vertical Post (3) to Main Base (1) using two 3/8 x 4-1/4 Hex Bolts (71), four 3/8 Washers (90) and two 3/8 Lock Nuts (85)

13 5. ASSEMBLY STEPS Step 3 Slide Top Plate (30) and Weight Plate Selection Rod (29) up, and then slide ten Weight Plates (31) into place as shown. Slide the Weight Selection Pin (33) into the weight plates. Attach Top Beam (5) to the top of the Guide Rods (4) using two 3/8 x1 Hex Bolts (76) and two 3/8 Washers (90). Place Top Beam (5) onto the Vertical Post (3) as shown. With the Upper Cable (63) in the groove of Red Pulley (53), install the pulley into the bracket of Top Beam (5) using one 3/8 x 2 Hex Bolt (74), two 3/8 Washers (90) and one 3/8 Lock Nut (85). Attach both Plates (62) to the Top Beam (5) using two 3/8 x 4-1/4 Hex Bolts (71), two 3/8 x 3/4 Allen Bolts (97), six 3/8 Washers (90) and two 3/8 Lock Nuts (85)

14 5. ASSEMBLY STEPS Step 4 Attach Bench Press Arm (13) to the Main Base (1) using one Ø19 x 280mm Pivot Shaft (84), two 5/8 Washers (92), two 5/8 Lock Nuts (87) and two 5/8 Plastic Dome Caps (43). Insert both Adjustable Press Frames A&B (17, 18) into the Bench Press Arm (13) using two PT-1B Pop Pins (51) as shown

15 5. ASSEMBLY STEPS Step 5 Attach Seat Cushion Support (9) to the Vertical Post (3) using two 3/8 x 2-1/8 Hex Bolts (75), four 3/8 Washers (90) and two 3/8 Locknuts (85). Attach Seat Support Post (10) to Main Base (1) using two 3/8 x 4-1/4 Hex Bolts (71), four 3/8 Washers (90) and two 3/8 Locknuts (85). Attach Seat Cushion Support (9) to Support Post (10) using one 3/8 x 2-1/2 Hex Bolt (72), two 3/8 Washers (90) and one 3/8 Locknut (85). Attach Leg Extension (11) to Support Post (10) using one 1/2 x 3-3/8 Hex Bolt (77), two 1/2 Washers (91), one 1/2 Lock nut (86) and two 1/2 Plastic Dome Caps (45). 1/2 PLASTIC DOME CAP 3/8 X 4-1/4 HEX BOLT 3/8 X 2-1/2 HEX BOLT 3/8 X 2-1/8 HEX BOLT 1/2 x 3-1/8 HEX BOLT 3/8 WASHER 1/2 WASHER 3/8 LOCK NUT 1/2 LOCK NUT

16 5. ASSEMBLY STEPS Step 6 Attach Butterfly Extension (6) to Vertical Post (3) using two 3/8 x 3-3/4 Hex Bolts (78), four 3/8 Washers (90) and two 3/8 Lock Nuts (85). Insert the shaft of Left Butterfly Arm (7) through the Left Adjustable Plate (15) to Butterfly Extension (6). Secure with one 5/8 Washer (92) and one 5/8 Locknut (87) and 5/8 Plastic Dome Cap (43). Attach Solid Handle (14) to Left Butterfly Arm (7) using one 3/8 x 1 Hex Bolt (76), one 3/8 Washer (90), one Washer (93) and 3/8 Plastic Dome Cap (44). Follow the above steps for the Right Butterfly Arm assembly. Attach two Single Pulley Brackets (23) to the bracket of Vertical Post (3) using two M8 x 60mm Hex Bolts (83), four M8 Washers (89) and two M8 Lock Nuts (88)

17 5. ASSEMBLY STEPS Step 7 Thread the Upper Cable (63) through the pulley brackets of the unit as shown. With Upper Cable (63) in the groove of Pulley (54), install Pulley (2) into the bracket of Top Beam (5) using one 3/8 x 2 Hex Bolt (74), two 3/8 Washers (90) and one 3/8 Lock Nut (85). With Upper Cable (63) in the groove of Pulley (54), install pulley 3 into top of Pulley Bracket Plate (24) using one 3/8 x 2 Hex Bolt (74), two 3/8 Washers (90) and one 3/8 Lock Nut (85). With Upper Cable (63) in the groove of Big Pulley (55), install the Pulley (4) into the bracket of Top Beam (5) using one 3/8 x 1-3/4 Hex Bolt (101), two 3/8 Washers (90) and one 3/8 Lock Nut (85). Attach bolt end of Upper Cable (63) to Weight Selection Rod (29) using one T3.0 x Ø13 x Ø32mm Washer (95) and one T3.0 x Ø26 x Ø46mm Washer (96). Attach ball end of Upper Cable (63) to Lat Bar (21) using two Chain Hooks (52) and one Chain (Short) (56)

18 5. ASSEMBLY STEPS Step 8 Thread the Butterfly Cable (65) through the brackets of unit as shown in the diagram. Attach one end of Butterfly Cable (65) to Right Adjustable Plate (16) using one 3/8 x 1-1/2 Hex Bolt (73), one 3/8 Washer (90) and one 3/8 Lock Nut (85). With Butterfly Cable (65) in groove of Pulley (54), install Pulley (5) into Single Pulley Bracket (23) using one 3/8 x 2 Hex Bolt (74), two 3/8 Washers (90) and one 3/8 Lock Nut (85). With Butterfly Cable (65) in groove of Pulley (54), install Pulley (6) into top of Intersect Pulley Bracket (25) using one 3/8 x 2 Hex Bolt (74), two 3/8 Washers (90) and one 3/8 Lock Nut (85). With Butterfly Cable (65) in groove of Pulley (54), install Pulley (7) into Single Pulley Bracket (23) using one 3/8 x 2 Hex Bolt (74), two 3/8 Washers (90) and one 3/8 Lock Nut (85). Attach one end of Butterfly Cable (65) to Left Adjustable Plate (15) using one 3/8 x 1-1/2 Hex Bolt (73), one 3/8 Washer (90) and one 3/8 Lock Nut (85)

19 5. ASSEMBLY STEPS Step 9 Thread the Low Cable (64) through brackets as shown in the diagram. With Low Cable (64) in groove of Red Pulley (8), install the pulley into the holes of Leg Extension (11) with one 3/8 x 2-1/2 Hex Bolt (72), two Ø13 x T1.0 x 11mm Bushings (98), two 3/8 Washers (90) and one 3/8 Lock Nut (85). With Low Cable (64) in groove of Pulley (9), install the pulley into the holes of Seat Support Post (10) with one 3/8 x 3 Hex Bolt (79), two Ø13 x T1.0 x 17mm Bushings (99), two 3/8 Washers (90) and one 3/8 Lock Nut (85). With Low Cable (64) in groove of Pulley (10, 12), install the pulleys into the brackets of Bench Press Arm (13) with one 3/8 x 3-3/8 Hex Bolt (70), two 3/8 Washers (90) and one 3/8 Lock Nut (85). With Low Cable (64) in groove of Pulley (11), install the pulley into the slot of Vertical Post (3) with one 3/8 x 3-3/8 Hex Bolt (70), two 3/8 Washers (90), two Ø13 x T1.0 x 22mm Bushings (100) and one 3/8 Lock Nut (85). With Low Cable (64) in groove of Pulley (13), install the pulley into the bracket of Vertical Post (3) with one 3/8 x 2 Hex Bolt (74), two 3/8 Washers (90) and one 3/8 Lock Nut (85). With Low Cable (64) in groove of Pulley (14), install the pulley into the lower of the Intersect Pulley Bracket (25) with one 3/8 x 2 Hex Bolt (74), two 3/8 Washers (90) and one 3/8 Lock Nut (85). With Low Cable (64) in groove of Pulley (15), install the pulley into the bracket of Main Base (1) with one 3/8 x 2 Hex Bolt (74), two 3/8 Washers (90) and one 3/8 Lock Nut (85). With Low Cable (64) in groove of Pulley (16), install the pulley into the lower of Pulley Bracket Plate (24) with one 3/8 x 2 Hex Bolt (74), two 3/8 Washers (90) and one 3/8 Lock Nut (85). Attach the end of Low Cable (64) to the steel piece of Main Base (1) with One Chain Hook (52). Attach the other end of Low Cable (64) to Curl Bar (22) using two Chain Hooks (52) and one Chain (Long) (57). ASSEMBLY DIAGRAM ON NEXT PAGE

20 5. ASSEMBLY STEPS Step

21 5. ASSEMBLY STEPS Step 10 Attach Backrest Cushion (28) to Vertical Post (3) using two M8 x 42mm Hex Bolts (82) and two M8 Washers (89). Attach Seat Cushion (27) to Seat Cushion Support (9) using four M8 x 16mm Hex Bolts (81) and four M8 Washers (89)

22 5. ASSEMBLY STEPS Step 11 Attach Arm Curl Cushion (26) to the Arm Curl Frame (12) using two M8 x 16mm Hex Bolts (81) and two M8 Washers (89). Insert Arm Curl Frame (12) into Seat Support Post (10) and secure with PT-1B Pop Pin. Insert Foam Rod (20) through the bushing of Seat Support Post (10) then slide one Foam Roll (46) onto each end. Insert Foam Rod (19) through the holes of Leg Extension (11) then slide one Foam Roll (46) onto each end. Recheck all bolts and nuts are tightened securely before using the machine

23 6. FITNESS TIPS AND TECHNIQUES AEROBIC EXERCISE Aerobic exercise is any sustained activity that sends oxygen to your muscles via your heart and lungs. Aerobic exercise improves the fi tness of your lungs and heart - your body s most important muscle. Aerobic exercise fi tness is promoted by any activity that uses your large muscles (arms, legs, or buttock, for example). Your heart beats quickly and you breathe deeply. An aerobic exercise should be part of your entire exercise routine. WEIGHT TRAINING Along with aerobic exercising which helps get rid of and keep off the excess fat that our bodies can store, weight training is an essential part of the exercise routine process. Weight training helps tone, build and strengthen muscle. If you are working above your target zone, you may want to do a lesser amount of reps. And as always consult your physician before beginning any exercise program. MUSCLE CHART HOME GYM The exercise routine that is performed on the home gym will develop the upper and lower body muscle group as well as condition the circulatory system and provide a good aerobic workout. These muscle groups are highlighted on the muscle chart below

24 7. CONDITIONING GUIDELINES How you begin your exercise program depends on your physical condition. If you have been inactive for several years, or are severely overweight, you must start slowly and increase your time on the equipment; a few minutes per workout. Initially, you may be able to exercise only for a few minutes in your target zone, however, your aerobic fitness will improve over the next six to eight weeks. Don t be discouraged if it takes longer. It s important to work at your own pace. Ultimately, you ll be able to exercise continuously for 30 minutes. The better your aerobic fitness, the harder you will have to work to stay in your target zone. Please remember these essentials : Have your doctor review your training and diet programs to advise you of a workout routine you should adopt. Begin your training program slowly with realistic goals that have been set by you and your doctor. Monitor your pulse frequently. Establish your target heart rate based on your age and condition. Set up your equipment on a flat, even surface at least 3 feet from walls and furniture. EXERCISE INTENSITY To maximize the benefits of exercising, it is important to exercise with the proper intensity. The proper intensity level can be found by using your heart rate as a guide. For effective aerobic exercise, your heart rate should be maintained at a level between 65% and 85% of your maximum heart rate as you exercise. This is known as your target zone. You can find your target zone in the table below. During the first few months of your exercise program, keep your heart rate near the low end of your target zone as you exercise. After a few months, your heart rate can be increased gradually until it is near the middle of your target zone as you exercise. To measure your heart rate, stop exercising but continue moving your legs or walking around and place two fingers on your wrist. Take a six-second heartbeat count and multiply the results by 10 to find your heart rate. For example, if your six-second heartbeat count is 14, your heart rate is 140 beats per minute. (A six-seconds count is used because your heart rate will drop rapidly when you stop exercising.) Adjust the intensity of your exercise until your heart rate is at the proper level. For more information visit

25 8. WARM-UP AND COOL-DOWN WORKOUT GUIDELINES Each workout should include the following three parts: A warm-up, consisting of 5 to 10 minutes of stretching and light exercise. A proper warm-up increases your body temperature, heart rate, and circulation in preparation for exercise. Training zone exercise, consisting of 20 to 30 minutes of exercising with your heart rate in your training zone. (Note: During the first few weeks of your exercise program, do not keep your heart rate in your training zone for longer than 20 minutes.) A cool-down, with 5 to 10 minutes of stretching. This will increase the flexibility of your muscles and will help to prevent post-exercise problems. EXERCISE FREQUENCY To maintain or improve your condition, plan three workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each week, if desired. Remember, the key to success is make exercise a regular and enjoyable part of your everyday life. 1 SUGGESTED STRETCHES The correct form for several basic stretches is shown at the right. Move slowly as you stretch, never bounce. 1. Toe Touch Stretch Stand with your knees bent slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax. Repeat 3 times. Stretches: Hamstrings, back of knees and back Hamstring Stretch Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg. Reach toward your toes as far as possible. Hold for 15 counts, then relax. Repeat 3 times for each leg. Stretches: Hamstrings, lower back and groin Calf/Achilles Stretch With one leg in front of the other, reach forward and place your hands against a wall. Keep your back leg straight and your back foot flat on the floor. Bend your front leg, lean forward and move your hips toward the wall. Hold for 15 counts, then relax. Repeat 3 times for each leg. To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles tendons and ankles Quadriceps Stretch With one hand against a wall for balance, reach back and grasp one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. Repeat 3 times for each leg. Stretches: Quadriceps and hip muscles. 5. Inner Thigh Stretch Sit with the soles of your feet together and your knees outward. Pull your feet toward your groin area as far as possible. Hold for 15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip muscles. For more information visit

26 9. EXERCISE PROGRAM DEVELOPING AN EXERCISE PROGRAMME For the first month of training you should allow your body to adjust to its new workload. For the first 2 to 4 weeks you should only perform one work set of each exercise, only increasing the number of sets you perform after this adjustment period. Develop your workout according to the time available to you and remember, the more effort you put in, the greater the benefits and the quicker you will see results. DIET Diet is a very important aspect of any fitness programme. A balanced diet will help you get to your goal weight. EXERCISE TECHNIQUE Hand Grips There are two styles of handgrips that can be used when exercising: Overhand Grip The bar is gripped with the hands reaching over the top of the bar and the palms facing in towards the body Underhand Grip The bar is gripped with the hands reaching under the bar and the palms facing away from the body. Breathing Breathing at the correct time is an important part of weight training. Breathe out while you are putting the effort into the movement, i.e. when you are lifting or pushing the weight. Breathe in on the return movement or the part of the movement that requires the least effort. Never hold your breathe during an exercise. Exercise Style All exercises should be done in a controlled manner. Do not jerk the weight around as this can lead to injury as well as limiting the benefit of the exercise. THE WORKOUT The Warm Up Always warm up thoroughly before each workout session to help minimise the risk of injury. Warm up on any Trojan exercise bike or treadmill or any other similar machine. Weekly Routine Perform a weight training routine 3 times per week, ensuring a day of rest and recovery between sessions

27 9. EXERCISE PROGRAM Reps and Sets Repetitions (Reps) is the term used to denote the number of consecutive times a certain movement is repeated without a break, while Sets denotes how many times you should repeat that exercise in a training session e.g. 3 sets of 10 reps means you should perform 10 reps for 1 set, have a break and then repeat another 2 sets. Recommended rep ranges 6-8 reps for Functional strength and hypertrophy (increase in muscle size) 8-12 reps for Total hypertrophy (increase in muscles size) reps Muscle-Strength endurance SAFE USE OF YOUR EQUIPMENT When using a barbell always ensure that there is someone to help you if you get into any difficulty on an exercise specifically when bench pressing, shoulder pressing or squatting. As you start using heavier weights, it is advised that you train with someone as you can help each other out while training and motivate one another to achieve your goals. Do s and Don ts Do make sure that your weights are firmly clamped to the bar. Do seek medical advice before starting any exercise programme. Do start off slowly to avoid unnecessary soreness and stiffness. Do remember to bend at the knees when lifting heavy weights from the floor. Do maintain a firm, straight back when lifting weights. Do remember to breath properly. Do warm up thoroughly before exercising. Don t exercise within 2 hours of eating a large meal. Do ensure that there is someone to help you when you lift heavy weights

28 10. FREQUENTLY ASKED QUESTIONS Q1. How do I maintain my cables? 1. The cables work in conjunction with the pulleys. When assembling the unit; make sure not to over tighten the pulleys. The pulleys are meant to move freely. 2. Before your workout; make sure all the cables are lined up correctly on the pulleys. Q2. My movable parts are not moving freely. 1. Do not over tighten any bolt or nut which has bushes and movable parts. Q3. My weight stack is not moving freely. 1. Apply a light coating of grease to the guide tubes, as this will help reduce any unnecessary friction. Q4. Is it possible to secure my gym to the ground? 1. Yes, provided that the area in which you are going to secure it is going to be in in a permanent location and that the floors are not tiled. Q5. My gym is not stable. 1. Ensure that all bolts are tightened and that all the end caps are on legs. Q6. Is it a good idea to use my gym in a commercial gym. 1. No, as it is for domestic use only

29 11. EXPLODED DRAWING

30 12. TROJAN 1 YEAR LIMITED WARRANTY The Manufacturer hereby provides a warranty to the original purchaser of this product ( the Consumer ) that this product will be free of manufacturing defects in materials and workmanship which under normal, personal, family or household use (commercial use expressly excluded) manifest themselves within the 1 year from the date of purchase. EXCLUSIONS The warranty does not include and will not be construed to cover products damaged as a result of disaster; misuse; commercial use; use not in accordance within the written instructions included with the product; abuse and/or any non-authorized modification of the product, incorrect installation of the product or normal wear and tear. All demo models carry a 3 month warranty. WAIVER The warranty and the obligations of the manufacturer provided herein are in lieu of, and the consumer, waives all other warranties, guarantees, conditions or liabilities, express or implied, arising by law or otherwise, including without limitation, any obligation of the manufacturer in respect of any injury, loss or damage (direct, indirect or consequential) arising out of the use of, or inability to use this product and whether or not occasioned by the manufacturer s negligence or any act or omission on its part. PROOF OF PURCHASE Any claim in terms of the warranty must be supported by a proof of purchase or a warranty number. Warranty numbers can be issued through contacting our call centre on (0861 Trojan), or online at If such proof is not available, then notwithstanding anything to the contrary herein, the service agent s prevailing charges for services/repairs including call-out and/or spares will be payable by the Consumer upon collection or delivery of the repaired product. The Consumer does not need to return the product to the store. The Consumer shall phone the Trojan hotline on (0861 Trojan) and the Manufacturer s authorized agent will at its discretion either repair the item at the Consumer s residence or collect and repair the item at their premises. During the warranty period the product may only be serviced and/or repaired by the Manufacturer s duly authorized agent(s) Masstores (Pty). Ltd., 16 Peltier Drive, Sunninghill, Johannesburg, 2191, South Africa.

31 13. TROJAN REPAIRS PROCEDURE 1. Procedure for repairs Should you experience any faults or breakdowns on your Trojan equipment, please adhere to the following procedure to have the fault rectified speedily and professionally. Do not return the product to the store* Call 0861 Trojan ( ) to log the faulty product (under warranty or out of warranty) The operator or technical advisor will try identify the fault, and will book a service team call out. The service team will endeavour to fix the problem in your home on an agreed date and time. Only if the fault cannot be repaired in the convenience of your home, will the service team take the faulty product back to the service centre. Items repaired in our service centre will be returned to your home on an agreed date and time. * Note: Should you live in an outlying area, it may be neccessary to return the product to the store nearest to you. Our service operator will advise you of your repair procedure. 2. Cost of Repairs 2.1 Under warranty Any items still under warranty will be repaired free of charge, as long as it complies with the terms and conditions of the warranty. (refer to warranties section in this manual) Any items that need to be repaired that are NOT covered in the warranty will be for the consumer s expense. A quote for the repair/replacement of these items will be provided to the consumer for approval prior to repairs being conducted. 2.2 Out of Warranty Any items that need to be repaired once the warranty has expired will be for the consumer s expense including call out fees. A quote for the repair/replacement of these items will be provided to the consumer for approval prior to repairs being conducted TROJAN