PERMATEX INDUSTRIAL CORPORATION 07/02/97 ROCKY HILL, CONNECTICUT TELEPHONE: (860) MATERIAL SAFETY DATA SHEET Page 01 of 06

Size: px

Start display at page:

Download "PERMATEX INDUSTRIAL CORPORATION 07/02/97 ROCKY HILL, CONNECTICUT TELEPHONE: (860) MATERIAL SAFETY DATA SHEET Page 01 of 06"

Judith Shaw
5 years ago
Views:

1 CHEMICAL PRODUCT AND COMPANY IDENTIFICATION MATERIAL SAFETY DATA SHEET Page 01 of 06 Part No.: 6MA Part Number: 6MA Product Type: RTV-Silicone Aerosol 2. COMPOSITION, INFORMATION ON INGREDIENTS Ingredients CAS No. % Non-hazardous ingredients Proprietary Poly(dimethylsiloxane), hydroxy terminated Ethyltriacetoxysilane Methyltriacetoxysilane SILICA, AMORPHOUS (FUMED) ACETIC ACID *** BUTANE PROPANE ISOBUTANE ***When this product is exposed to moisture, 3-5% acetic acid may be formed. Ingredients which have exposure limits Exposure Limits (TWA) ACGIH OSHA OTHER Ingredients (TLV) (PEL) SILICA, AMORPHOUS (FUMED) 10mg/m3 TWA 6mg/m3 TWA None ACETIC ACID 10 ppm TWA 10 ppm TWA None 25 mg/m3 25 mg/m3

2 MATERIAL SAFETY DATA SHEET Page 02 of COMPOSITION, INFORMATION ON INGREDIENTS (continued) BUTANE 800 ppm TWA 800 ppm TWA None 1900mg/M3 1900mg/M3 PROPANE Asphyxiant 1000 ppm None 1800 mg/m3 Exposure Limits (STEL) ACGIH OSHA Ingredients (TLV) (PEL) ACETIC ACID 15 ppm None 37 mg/m3 3. HAZARDS IDENTIFICATION Toxicity: Primary Routes of Entry: Signs and symptoms of Exposure: Existing Conditions Aggravated by Exposure: Eye and skin irritant. Moderately toxic by ingestion. If use creates respirable particles, some respiratory systems injury may occur. May enhance allergic conditions in certain people. Skin, ingestion, inhalation, eyes. Acetic acid produced during cure irritates eyes, nose throat. May cause moderate corneal injury and considerable redness to eyes. Inhalation may may cause difficulty in breathing. Ingestion may cause vomiting. Swallowing large amounts may cause digestive discomfort. Heart disease and respiratory disorders. Methyltriacetoxysilane: Eye, skin, and pulmonary disorders. Literature Referenced Carcinogen Ingredients Target Organ and Other Health Effects NTP IARC OSHA Non-hazardous ingredients No Data NO NO NO Poly(dimethylsiloxane), hydroxy terminated No Data NO NO NO Ethyltriacetoxysilane No Data NO NO NO

3 Methyltriacetoxysilane No Data NO NO NO MATERIAL SAFETY DATA SHEET Page 03 of HAZARDS IDENTIFICATION (continued) SILICA, AMORPHOUS (FUMED) NUI NO N/A NO ACETIC ACID COR EYE GAS IMM IRR NO NO NO BUTANE CAR CNS IRR NO NO NO PROPANE CAR CNS IRR NO NO NO ISOBUTANE CAR CNS LUN NO NO NO Abbreviations N/A Not Applicable CNS Central nervous system EYE Eyes IMM Immune system LUN Lung CAR Cardiac COR Corrosive GAS Gastrointestinal IRR Irritant NUI Nuisance dust 4. FIRST AID MEASURES Ingestion: Inhalation: Skin Contact: Eye Contact: Do not induce vomiting. Keep individual calm. Obtain medical attention. Remove to fresh air. Treat symptomatically. Wipe off paste with paper towel or cloth. Wash exposed area with soap and water. Flush at least 15 minutes with water. Obtain medical attention. 5. FIRE FIGHTING MEASURES Flash Point: 212 F (Base only) Method: Tag closed cup Recommended Extinguishing Agents: Carbon dioxide, water fog, dry chemical Hazardous Products formed by Fire or Thermal Decomp Acetic acid, formaldehyde, silica fume, carbon dioxide Unusual Fire or Explosion Hazards: Containers may vent, rupture, or burst at elevated temperatures.

4 Explosive Limits: (% by volume in air)lower 1.8% (% by volume in air)upper 9.5% MATERIAL SAFETY DATA SHEET Page 04 of ACCIDENTAL RELEASE MEASURES Steps to be taken in case of spill or leak: Wipe and/or scrape up spilled material. Maintain good ventilation for large spills. Place scrap material in a well-ventilated place and allow to cure to rubber. 7. HANDLING AND STORAGE Safe Storage: Store away from heat, spark or open flame. Store below 120 F. (Contact Loctite Customer Service for shelf Life information) Handling: Avoid prolonged breathing of vapor. Keep away from eyes. Avoid prolonged skin contact. Keep away from heat, sparks, or open flame. Do not smoke while using. Wash hands after use. When spraying more than one half can or more than one can consecutively, use NIOSH/MSA approved respirator. 8. EXPOSURE CONTROLS, PERSONAL PROTECTION Eyes: Skin: Ventilation: Safety glasses or goggles. Rubber or plastic gloves. Long sleeves and long pants. Provide adequate local ventilation to maintain vapor concentration below TLV. Use self contained breathing apparatus when vapor concentration exceeds TLV. 9. PHYSICAL AND CHEMICAL PROPERTIES See Section 2 for Exposure Limits. The properties listed below apply to the base material only. Appearance: Odor: Boiling Point: ph: Blue paste Acetic acid None: Polymeric Material Does not apply

5 Solubility in Water: Nil Specific Gravity 1.04 Volatile Organic Compound (EPA Method 24) 9.6% ; 100 grams per liter (calculated) Vapor Pressure: 66 psig Vapor Density: More than 1 MATERIAL SAFETY DATA SHEET Page 05 of PHYSICAL AND CHEMICAL PROPERTIES (continued) Evaporation Rate (Ether = 1) Slower than butyl acetate 10. STABILITY AND REACTIVITY Stability: Stable Hazardous Polymerization: Will not occur Incompatibility: Strong acids. Adhesive is polymerized by contact with moisture. Conditions to Avoid: Not available Hazardous Decomposition Products (non-thermal): Acetic acid fumes. 11. TOXICOLOGICAL INFORMATION 12. ECOLOGICAL INFORMATION 13. DISPOSAL CONSIDERATIONS Recommended methods of disposal: See Section 3. No data available Cured rubber scrap can be incinerated. Follow EPA local regulations for disposal of aerosol cans. EPA Hazardous Waste Number D001 - Hazardous waste per 40CFR TRANSPORTATION INFORMATION DOT (49 CFR 172) Domestic Ground Transport Proper Shipping Name: Consumer Commodity Hazard Class or Division: ORM-D Identification Number: None

6 Marine Pollutant: None IATA Proper Shipping Name: Consumer Commodity (Not more than 500 ml); Aerosols, flammable n.o.s. (More than 500 ml) Class or Division: Class 9 (Not more than 500 ml); Division 2.1 (More than 500 ml) UN or ID Number: ID 8000 (Not more than 500 ml); UN 1950 (More than 500 ml) MATERIAL SAFETY DATA SHEET Page 06 of REGULATORY INFORMATION CA Proposition 65: No Prop65 chemicals are known to be present. 16. OTHER INFORMATION Estimated NFPA(R) Code: Health Hazard: 1 Fire Hazard: Sealant: 1; Propellant: 4 Reactivity Hazard: 0 Specific Hazard: Does not apply Estimated HMIS(R) Code: Health Hazard: 1 Flammability Hazard: Sealant: 1; Propellant: 4 Reactivity Hazards: 0 Personal Protection: See Section 8. NFPA is a registered trademark of the National Fire Protection Assn. HMIS is a registered trademark of the National Paint and Coatings Assn. Prepared By: Stephen Repetto Title: Research Chemist, Health and Safety Company: Loctite Corp., 1001 Tr Br Cr, Rocky Hill CT (24hr.) Phone: (860) Revision Date: January 22, 1996 Revision: 0005

HENKEL LOCTITE CORPORATION 10/28/02 ROCKY HILL, CONNECTICUT EMERGENCY PHONE: (860) MATERIAL SAFETY DATA SHEET Page 01 of 05

HENKEL LOCTITE CORPORATION 10/28/02 ROCKY HILL, CONNECTICUT EMERGENCY PHONE: (860) MATERIAL SAFETY DATA SHEET Page 01 of 05 81204 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION MATERIAL SAFETY DATA SHEET Page 01 of 05 Product Type: Aerosol lubricant 2. COMPOSITION, INFORMATION ON INGREDIENTS Ingredients CAS No. % STODDARD SOLVENT