Sony Ericsson W810I Vibration Cell

Size: px

Start display at page:

Download "Sony Ericsson W810I Vibration Cell"

Shannon Freeman
5 years ago
Views:

1 Sony Ericsson W810I Vibration Cell Replacement How to install a new vibration cell in your Sony Ericsson W810I. Geschrieben von: Lucy Bowen ifixit CC BY-NC-SA de.ifixit.com Seite 1 von 11

2 WERKZEUGE: Heavy-Duty Spudger (1) Phillips #00 Screwdriver (1) ifixit Opening Tools (1) T6 Torx Screwdriver (1) ifixit CC BY-NC-SA de.ifixit.com Seite 2 von 11

Schritt 2 Remove the battery cover by applying downward pressure on the

3 Schritt 1 Battery Place your Sony Ericsson W810I screen side down with the battery cover facing up as shown. Schritt 2 Remove the battery cover by applying downward pressure on the Singular Symbol and then shifting the pressure towards the bottom edge of the phone. ifixit CC BY-NC-SA de.ifixit.com Seite 3 von 11

4 Schritt 3 Lift the bottom of the battery away from the phone with your thumb and rotate until the opening in the bottom of the case is oriented downward. The battery should slide out. Schritt 4 Case Remove the two 3.9mm screws with a Phillips size #00 screwdriver. Remove the two 6.35mm screws with a Torx T6 screwdriver. ifixit CC BY-NC-SA de.ifixit.com Seite 4 von 11

5 Schritt 5 Run a plastic opening tool along the edge of the back casing while prying it apart to remove it. Schritt 6 Turn the phone over and open the memory stick compartment. Stick a plastic opening tools into the opening and twist it to gain some leverage. This should begin separating the front casing from the interior plastic support frame. ifixit CC BY-NC-SA de.ifixit.com Seite 5 von 11

6 Schritt 7 Run the plastic opening tool upwards along that side, removing the housing. Schritt 8 Key Pad Peel the rubber keys away from their backing. Do not slide them off. Set them aside. ifixit CC BY-NC-SA de.ifixit.com Seite 6 von 11

7 Schritt 9 Insert a plastic opening tool under the left side of the keypad backing and start to lift. Lift slowly, as you can damage the ribbon cable underneath if you pull the keypad backing away too forcefully. Schritt 10 Insert the plastic opening tool under the ribbon cable attachment and give a small push upwards to dislodge it. ifixit CC BY-NC-SA de.ifixit.com Seite 7 von 11

Schritt 11 LCD Screen Remove the indicated 6.

Schritt 12 Pull LCD screen gently out and the to

point of attachment with a plastic opening tool

8 Schritt 11 LCD Screen Remove the indicated 6.35mm screws with a Torx T6 screwdriver. Schritt 12 Pull LCD screen gently out and the to side. Do not attempt to pull it completely away from the board below it. Push up on the underside of the cable at the point of attachment with a plastic opening tool to detach it. The screen can now be separated. ifixit CC BY-NC-SA de.ifixit.com Seite 8 von 11

plastic opening device, push against the

9 Sony Ericsson W810I Vibration Cell Replacement Schritt 13 Motherboard Using a plastic opening device, push against the underside of the brown portion of the the ribbon cable to unplug it. Schritt 14 ifixit CC BY-NC-SA de.ifixit.com Using a plastic opening device, separate the top of the motherboard from the rest of the plastic casing. Seite 9 von 11

Schritt 15 Pull forwards slightly on the motherboard so that

Thread the ribbon cable through the hole in the motherboard

Schritt 16 Vibration Cell This is the vibration cell.

10 Schritt 15 Pull forwards slightly on the motherboard so that it starts to fall out of the casing. Thread the ribbon cable through the hole in the motherboard so that it does not become caught. Schritt 16 Vibration Cell This is the vibration cell. It causes the phone to vibrate when the vibrate setting is active. ifixit CC BY-NC-SA de.ifixit.com Seite 10 von 11

Schritt 17 Insert the spudger into the crack between the green rubber container

When the cell it is about halfway out, remove the spudger.

11 Schritt 17 Insert the spudger into the crack between the green rubber container and the plastic case and pry it out. When the cell it is about halfway out, remove the spudger. Reinsert the spudger into the crack between the metal top and the plastic case and pry it the rest of the way out. To reassemble your device, follow these instructions in reverse order. Dieses Dokument wurde zuletzt angelegt am :19:50 PM. ifixit CC BY-NC-SA de.ifixit.com Seite 11 von 11

Disassembling Sony Ericsson w600i LCD Section

Disassembling Sony Ericsson w600i LCD Section Disassembling the LCD section allows access to the LCD Buttons and LCD Screen. Geschrieben von: Beau Blanchard ifixit CC BY-NC-SA de.ifixit.com Seite 1 von