Fittings, Tubing & Nipples

Transcription

1 s, Tubing & Nipples P Series Pipe s s to 15,000 psi (1034 bar) Since 1945 utoclave Engineers has designed and built premium quality valves, fittings and tubing. This commitment to engineering and manufacturing excellence has earned utoclave a reputation for reliable, efficient product performance. utoclave Engineers has long been established as the world leader in high pressure fluid handling components for the chemical/petrochemical, research and oil and gas industries. Pipe s, Tubing and Nipples Features: vailable sizes are 1/4", 3/8", 1/2", 3/4" and 1" s and tubing manufactured from cold worked 316 stainless steel. Operating Temperatures from 0 F (-17.8 ) to 400 F (204 ). s,tubing & Nipples - P Series

2 Pipe s s to 15,000 psi (1034 bar) utoclave Engineers pipe fittings, P Series, are designed for liquid and gas applications. vailable from 1/4" to 1" NPT to 15,000 psi and temperatures to 400 F (204 ) atalog onnection imensions - inches (mm) lock Thickness Pipe Elbow PL4400 1/4" NPT 15, ( ) (10.67) (28.58) (38.10) (19.05) (19.05) (19.05) PL6600 3/8" NPT 15, ( ) (14.22) (38.10) (50.80) (25.40) (25.40) (25.40) PL8800 1/2" NPT 15, ( ) (17.53) (47.75) (76.20) (31.75) (38.10) (31.75) PL12 3/4" NPT 10, (689.46) (22.61) (55.37) (76.20) (38.10) (38.10) (35.05) PL16 1" NPT 10, (689.46) (28.58) (63.50) (104.65) (39.67) (52.37) (44.45) Pipe Tee PT4440 1/4" NPT 15, ( ) (10.67) (28.58) (38.10) (19.05) (19.05) (19.05) PT6660 3/8" NPT 15, ( ) (14.22) (38.10) (50.80) (25.40) (25.40) (25.40) PT8880 1/2" NPT 15, ( ) (17.53) (47.75) (76.20) (31.75) (38.10) (31.75) PT12 3/4" NPT 10, (689.46) (22.61) (55.37) (76.20) (38.10) (38.10) (35.05) PT16 1" NPT 10, (689.46) (28.58) (63.50) (104.65) (39.67) (52.37) (44.45) Pipe ross PX4444 1/4" NPT 15, ( ) (10.67) (38.10) (38.10) (19.05) (19.05) (19.05) PX6666 3/8" NPT 15, ( ) (14.22) (50.80) (50.80) (25.40) (25.40) (25.40) PX8888 1/2" NPT 15, ( ) (17.53) (63.50) (76.20) (31.75) (38.10) (31.75) PX12 3/4" NPT 10, (689.46) (22.61) (76.20) (76.20) (38.10) (38.10) (35.05) PX16 1" NPT 10, (689.46) (28.58) (79.38) (104.65) (39.67) (52.37) Figure (44.45) 3 *Maximum pressure rating is based on the lowest rating of any component. ctual working pressure may be determined by pipe pressure rating, if lower. ll dimensions for reference only and subject to change. Figure 3 For prompt service, utoclave stocks select products. onsult your local representative. For mounting hole option add suffix PM to catalog number. onsult factory for mounting hole dimensions. Figure 3 Elbow Tee ross 2 ll general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.

3 atalog onnection imensions - in.(mm) Pipe oupling 15F4488 1/4" NPT 15, ( ) (10.67) (19.05) (38.10) 15F6688 3/8" NPT 15, ( ) (14.22) (25.40) (41.28) 15F8888 1/2" NPT 15, ( ) (17.53) (30.23) (50.80) 10F /4" NPT 10, (689.46) (22.61) (30.06) (69.90) 10F " NPT 10, (689.46) (28.58) (44.50) (63.50) Figure 4 atalog onnection imensions - inches (mm) E Max Pipe ulkhead oupling 15F4488 1/4" NPT 15, ( ) (10.67) (23.80) (50.80) (25.40) (15.75) (9.65) 15F6688 3/8" NPT 15, ( ) (14.22) (28.60) (60.50) (35.05) (20.07) (9.65) 15F8888 1/2" NPT 15, ( ) (17.53) (42.67) (66.80) (47.80) (23.11) (9.65) 10F /4" NPT 10, (689.46) (22.61) (42.67) (66.80) (47.80) (23.11) (9.65) 10F " NPT 10, (689.46) (28.58) (49.28) (88.90) (47.50) (38.10) (9.65) Figure 5 atalog Pipe Plugs onnection *Maximum pressure rating is based on the lowest rating of any component. + distance across flats ll dimensions for reference only and subject to change. For prompt service, utoclave stocks select products. onsult your local representative. imensions - in.(mm) PP40 1/4" NPT 15, ( ) (16.00) (28.45) PP60 3/8" NPT 15, ( ) (19.05) (28.45) PP80 1/2" NPT 15, ( ) (25.40) (38.10) PP120 3/4" NPT 10, (689.46) (35.05) (38.10) PP160 1" NPT 10, (689.46) (35.05) (47.75) Figure 6 NOTE: NPT (Pipe) onnections: - NPT threads must be sealed using a high quality PTFE tape and/or paste product. Refer to thread sealant manufacturer's instructions on how to apply thread sealant. - Sealing performance may vary based on many factors such as pressure, temperature, media, thread quality, thread material, proper thread engagement and proper use of thread sealant. - ustomer should limit the number of times an NPT fitting is assembled and disassembled because thread deformation during assembly will result in deteriorating seal quality over time. When using only PTFE tape, consider using thread lubrication to prevent galling of mating parts. Figure 4 HEX (=Panel hole drill size) Figure 5 E MX Figure 6 HEX HEX oupling ulkhead oupling Plugs ll general terms and conditions of sale, including limitations of our liability, apply to all products and services sold. 3

4 s to 15,000 (1034 bar) atalog onnection imensions - inches (mm) lock Thickness Street Pipe Elbow SPL4400 1/4" NPT 15, ( ) (5.54) (38.10) (38.10) (28.70) (25.40) (19.05) SPL6600 3/8" NPT 15, ( ) (7.54) (44.75) (38.10) (31.75) (25.40) (25.40) SPL8800 1/2" NPT 15, ( ) (9.12) (57.15) (50.80) (41.40) (31.75) (31.75) SPL12 3/4" NPT 10, (689.46) (14.47) (63.50) (66.55) (44.45) (33;27) (38.10) SPL16 1" NPT 10, (689.46) (19.43) Male Pipe Elbow MPL4400 1/4" NPT 15, ( ) (5.54) (38.10) (38.10) (28.70) (28.70) (19.05) MPL6600 3/8" NPT 15, ( ) (7.54) (44.45) (44.45) (31.75) (31.75) (25.40) MPL8800 1/2" NPT 15, ( ) (9.12) (50.80) (50.80) (38.10) (38.10) (25.40) MPL12 3/4" NPT 10, (689.46) (14.47) (66.55) (66.55) (44.45) (44.45) (38.10) MPL16 1" NPT 10, (689.46) (19.43) (76.20) (76.20) (54.10) (54.10) (35.05) Male Pipe Tee MPT4440 1/4" NPT 15, ( ) (5.54) (57.15) (38.10) (28.70) (28.70) (19.05) MPT6660 3/8" NPT 15, ( ) (7.54) (63.50) (44.45) (44.45) (31.75) (25.40) MPT8880 1/2" NPT 15, ( ) (9.12) (76.20) (50.80) (38.10) (38.10) (25.40) MPT12 3/4" NPT 10, (689.46) (14.47) (88.90) (66.55) (44.45) (44.45) (38.10) MPT16 1" NPT 10, (689.46) (19.43) (104.65) (76.20) (54.10) (54.10) (44.45) Figure 3 Figure 3 Street Elbow Male Elbow Male Tee 4 ll general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.

5 atalog onnection imensions - inches (mm) lock Thickness Street Pipe Tee SPT4440 1/4" NPT 15, ( ) (5.54) (50.80) (35.05) (20.57) (25.40) (19.05) SPT6660 3/8" NPT 15, ( ) (7.54) (63.50) (38.10) (25.40) (25.40) (25.40) SPT8880 1/2" NPT 15, ( ) (9.12) (76.20) (44.45) (38.10) (31.75) (31.75) SPT12 3/4" NPT 10, (689.46) (14.47) (79.25) (66.55) (35.05) (33.27) (38.10) SPT16 1" NPT 10, (689.46) (19.43) (104.65) (76.20) (54.10) (54.10) (44.45) Male ranch Tee PT4440 1/4" NPT 15, ( ) (5.54) (50.80) (38.10) (25.40) (28.70) (19.05) PT6660 3/8" NPT 15, ( ) (7.54) (50.80) (44.45) (25.40) (31.75) (25.40) PT8880 1/2" NPT 15, ( ) (9.12) (76.20) (57.15) (44.45) (41.15) (31.75) PT12 3/4" NPT 10, (689.46) (14.47) (76.20) (63.50) (38.10) (44.45) (35.05) PT16 1" NPT 10, (689.46) (19.43) (104.65) (76.20) (52.32) (54.10) (44.45) Figure 4 Figure 5 Figure 4 Figure 5 Street Tee ranch Tee NOTE: NPT (Pipe) onnections: - NPT threads must be sealed using a high quality PTFE tape and/or paste product. Refer to thread sealant manufacturer's instructions on how to apply thread sealant. - Sealing performance may vary based on many factors such as pressure, temperature, media, thread quality, thread material, proper thread engagement and proper use of thread sealant. - ustomer should limit the number of times an NPT fitting is assembled and disassembled because thread deformation during assembly will result in deteriorating seal quality over time. When using only PTFE tape, consider using thread lubrication to prevent galling of mating parts. 5

6 Pipe Hex Nipples s to 15,000 psi (1034 bar) For rapid system make-up, utoclave Engineers supplies pipe nipples in various sizes and lengths for pipe valves and fittings. Special lengths In addition to the standard lengths listed in the table below, nipples are available in custom lengths. onsult factory. atalog onnection imensions - in.(mm) Hex Pipe Hex lose Nipples 15MP4P4 1/4" NPT 15, ( ) (5.54) (16.00) (46.02) 15MP6P6 3/8" NPT 15, ( ) (7.54) (19.05) (47.63) 15MP8P8 1/2" NPT 15, ( ) (9.12) (23.88) (63.50) 10MP12P12 3/4" NPT 10, (689.46) (14.47) (30.23) (63.50) 10MP16P16 1" NPT 10, (689.46) (19.43) (35.05) (81.03) Pipe Hex Nipples 15MP4P4-4 1/4" NPT 15, ( ) (5.54) (16.00) (101.60) 15MP4P4-6 1/4" NPT 15, ( ) (5.54) (16.00) (152.40) 15MP4P4-8 1/4" NPT 15, ( ) (5.54) (16.00) (203.20) 15MP6P6-4 3/8" NPT 15, ( ) (7.54) (19.05) (101.60) 15MP6P6-6 3/8" NPT 15, ( ) (7.54) (19.05) (152.40) 15MP6P6-8 3/8" NPT 15, ( ) (7.54) (19.05) (203.20) 15MP8P8-4 1/2" NPT 15, ( ) (9.12) (23.88) (101.60) 15MP8P8-6 1/2" NPT 15, ( ) (9.12) (23.88) (152.40) 15MP8P8-8 1/2" NPT 15, ( ) (9.12) (23.88) (203.20) 10MP12P12-4 3/4" NPT 10, (689.46) (14.47) (30.23) (101.60) 10MP12P12-6 3/4" NPT 10, (689.46) (14.47) (30.23) (152.40) 10MP12P12-8 3/4" NPT 10, (689.46) (14.47) (30.23) (203.20) 10MP16P16-4 1" NPT 10, (689.46) (19.43) (35.05) (101.60) 10MP16P16-6 1" NPT 10, (689.46) (19.43) (35.05) (152.40) 10MP16P16-8 1" NPT 10, (689.46) (19.43) (35.05) (203.20) Pipe Hex Reducer Nipples 15MP4P6 1/4" to 3/8" NPT 15, ( ) (5.16) (19.05) (47.75) 15MP4P8 1/4" to 1/2" NPT 15, ( ) (5.16) (23.88) (58.67) 10MP8P16 1/2" to 1" NPT 15, ( ) (9.53) (35.05) (73.15) 10MP12P16 3/4" to 1" NPT 10, (689.46) (12.70) (35.05) (74.68) HEX HEX *Maximum pressure rating is based on the lowest rating of any component. ctual working pressure may be determined by tubing pressure rating, if lower. ll dimensions for reference only and subject to change. Pipe Nipple Reducer Nipple 6 ll general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.

7 Pipe heck Valves s to 15,000 (1034 bar) Pipe O-Ring heck Valves FLOW operating temperature for standard o-ring check valves 0 F (-17.8 ). Provides unidirectional flow and tight shut-off for liquids and gas with high reliability. When differential drops below cracking pressure*, valve shuts off. (Not for use as relief valve.) Materials: 316 Stainless Steel: body, cover, poppet, cover gland. 300 Series Stainless Steel: spring Standard O-ring: Viton, for operation to 400 F (204 ). una-n or Teflon available for 250 F (121 ) or 400 F (204 ) respectively; specify when ordering. *racking : 20 psi (1.38 bar) ±30%. Springs for higher cracking pressures (up to 100 psi (6.89 bar)) available on special order for O-ring style check valves only. Pipe all heck Valves FLOW operating temperature for pipe ball check valves 0 F (-17.8 ). Prevents reverse flow where leak-tight shut-off is not mandatory. When differential drops below cracking pressure, valve closes. With all-metal components, valve can be used up to 400 F (204 ). Technical Information section for connection temperature limitations. (Not for use as a relief valve.) all and poppet are an integral design to assure positive, in-line seating without chatter. Poppet is designed essentially for axial flow with minimum pressure drop. Materials: 316 Stainless Steel: body, cover, ball poppet, cover gland. 300 Series Stainless Steel: ball, spring. UTION: While testing has shown O-Rings to provide satisfactory service life, both cyclic and shelf life may vary widely with differing service conditions, properties of reactants, pressure and temperature cycling and age of the O-ring. FREQUENT INSPETIONS SHOUL E ME to detect any deterioration, and O-rings replaced as required. 7

8 Pipe heck Valves atalog onnection Rated v imensions - inches (mm) Hex Hex Pipe O-Ring heck Valves PO4400 1/4" NPT 15, ( ) (3.05) (85.60) (60.33) (20.57) (20.57) PO6600 3/8" NPT 15, ( ) (5.59) (100.33) (73.15) (25.40) (25.40) PO8800 1/2" NPT 15, ( ) (9.14) (136.14) (98.55) (35.05) (30.23) PO12 3/4" NPT 10, (689.46) (13.21) (159.77) (120.65) (44.45) (35.05) PO16 1" NPT 10, (689.46) (17.53) (186.18) (146.05) (47.75) (47.75) Pipe all heck Valves P4400 1/4" NPT 15, ( ) (3.05) (85.60) (60.33) (20.57) (20.57) P6600 3/8" NPT 15, ( ) (5.59) (100.33) (73.15) (25.40) (25.40) P8800 1/2" NPT 15, ( ) (9.12) (136.14) (98.55) (35.05) (30.23) P12 3/4" NPT 10, (689.46) (13.21) (159.77) (120.65) (44.45) (35.05) P16 1" NPT 10, (689.46) (17.53) (186.18) (146.05) (47.75) (47.75) heck Flow - water, GPM For flow rates using alternate fluids, consult utoclave Engineers. *Maximum pressure rating is based on the lowest rating of any component. + distance across flats ll dimensions for reference only and subject to change. For prompt service, utoclave stocks select products. onsult your local representative. NOTE: NPT (Pipe) onnections: - NPT threads must be sealed using a high quality PTFE tape and/or paste product. Refer to thread sealant manufacturer's instructions on how to apply thread sealant. - Sealing performance may vary based on many factors such as pressure, temperature, media, thread quality, thread material, proper thread engagement and proper use of thread sealant. - ustomer should limit the number of times an NPT fitting is assembled and disassembled because thread deformation during assembly will result in deteriorating seal quality over time. When using only PTFE tape, consider using thread lubrication to prevent galling of mating parts. HEX HEX ll general terms and conditions of sale, including limitations of our liability, apply to all products and services sold.! WRNING! FILURE OR IMPROPER SELETION OR IMPROPER USE OF THE PROUTS N/OR SYSTEMS ESRIE HEREIN OR RELTE ITEMS N USE ETH, PERSONL INJURY N/OR PROPERTY MGE. This document and other information from Snap-tite, Inc., its subsidiaries and authorized distributors, provides product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. ue to the variety of operation conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Snap-tite, Inc. and its subsidiaries at any time without notice. ISO-9001 ertified E-0709 Industrial Estate Whitemill-Wexford Republic of Ireland PH: FX: ste_sales@snap-tite.com Hessinger rive Erie, Pennsylvania US PH: FX: ae_sales@snap-tite.com